Board files for Phytec phyCARD-S "System on Module" and "Rapid
Development Kit".

Based on patches from:

Steffen Trumtrar <s.trumtrar@pengutronix.de>:
 - Original patch
 - ARM: dts: Set partition offsets for phycard
 - ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100
 - ARM: imx27-phytec-phycard-S.dts: resize nand partitions

Jan Luebbe <jlu@pengutronix.de>:
 - ARM: dts: Enable bad block table in NAND

Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Set operating-points for imx27. There is no regulator support, so the
voltages are 0. The frequencies should be the same for all imx27 boards,
so it is defined here and can be overwritten if necessary.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

On the MX27 Reference Manual the interrupt controller is named AITC:
ARM926EJ-S Interrupt Controller

So use the AITC term instead of AVIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Origin: id:1334193132-18944-2-git-send-email-festevam@gmail.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This adds pinmux entries for USBH1/2 in ULPI mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The mc13892 driver knows that it needs spi-cs-high, so the mc13892
will work. The dataflash also connected to this bus though can only
be probed when the mc13892 is inactive. Due to driver potential
differences in the probe order we can only make sure the mc13892
is inactive when we put the information into the devicetree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

For keeping the alphabetical order in the pinmux nodes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This allows to order the i2c and spi devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This allows to order the i2c and spi devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This allows to order the i2c and spi devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This allows to order the i2c devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This allows to order the i2c and spi devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The i.MX6 gpt is handled by the i.MX31 gpt driver in the kernel,
so add a corresponding compatible entry.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The i.MX6Q and i.MX6DL are pin compatible, so the pinmux entries
should be in sync. This patch systematically adds the pinmux entries
missing from the imx6q to the imx6dl file.
Some name inconsistencies and whitespace damage is fixed along the
way.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch adds the missing (Keypad Port) KPP devicetree node
for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Define minimal memory layout for i.MX27 PCM-038 module.
This will help to use appended DTB with non-DT capable bootloaders.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

i.MX27 have only one PWM, so index from PWM devicetree node removed.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch adds the missing (Digital Audio MUX) AUDMUX devicetree
node for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch adds the missing (Symmetric/Asymmetric Hashing and Random
Accelerator) SAHARA2 devicetree node for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

enable the spi nor for imx6q{dl}-sabresd boards.
Signed-off-by: Huang Shijie <b32955@freescale.com>

This new pinctrl is used by the imx6q-sabresd board.
Signed-off-by: Huang Shijie <b32955@freescale.com>

This new pinctrl is used in the imx6dl-sabresd board.
Signed-off-by: Huang Shijie <b32955@freescale.com>

It contains a bunch of imx soc updates for 3.12.

- Add more ethernet phy fixups for imx6 boards
- Add some missing imx6q clocks into clock driver
- Add new clock types fixup mux and div to work around some ugly
  hardware defect
- Consolidate L2 cache initialization function, so that it can be used
  on more i.MX SoCs
- Replace magic numbers in mach-imx6q.c with well defined macros
- Small fixes for imx6q and pllv3 clock drivers
- Some random updates on imx defconfig files

Add defines for common Micrel PHY setups so that other platforms
can use them. Update imx61 and sama5 hardware to use the micrel_phy.h
PHY defines.

Also add support for the KSZ9021RLRN PHY.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: David S. Miller <davem@davemloft.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Commit 02502da4 (ASoC: imx-mc13783: Depend on ARCH_ARM) caused the selection of
CONFIG_SND_SOC_IMX_MC13783 to be impossible due to a wrong dependency, which
caused CONFIG_SND_SOC_IMX_MC13783 to be removed after the defconfigs cleanups.

The original selection problem has been fixed by 9f19de64 (ASoC: imx-mc13783:
Make SND_SOC_IMX_MC13783 visible again), so it is possible to select
CONFIG_SND_SOC_IMX_MC13783 again as originally done.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Move anatop related (For USB) from board file to anatop driver
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Wandboard has a Broadcom 4329 chipset connected to SDHC, so turn on the wireless
related options.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Generate imx_v4_v5_defconfig by doing:

make imx_v4_v5_defconfig
make savedefconfig
cp defconfig arch/arm/configs/imx_v4_v5_defconfig

No functional change. The goal here is to cleanup imx_v4_v5_defconfig file to
make easier and cleaner the addition of new entries.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Let SATA support be built by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Generate imx_v6_v7_defconfig by doing:

make savedefconfig

cp defconfig arch/arm/configs/imx_v6_v7_defconfig

No functional change. The goal here is to cleanup imx_v6_v7_defconfig file to
make easier and cleaner the addition of new entries.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Current imx53_pm_init() implementation is incomplete as it lacks calling
suspend_set_ops().

Use a single imx5_pm_init() function to handle both mx51 and mx53.

This allows mx53 to enter in low-power mode.

Tested on a mx53qsb:

root@freescale /$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
mmc0: card e624 removed
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)

... (Press Power button)

PM: suspend of devices complete after 17.067 msecs
PM: suspend devices took 0.020 seconds
PM: late suspend of devices complete after 0.954 msecs
PM: noirq suspend of devices complete after 1.288 msecs
Disabling non-boot CPUs ...
PM: noirq resume of devices complete after 0.680 msecs
PM: early resume of devices complete after 0.914 msecs
PM: resume of devices complete after 44.955 msecs
PM: resume devices took 0.050 seconds
Restarting tasks ... done.
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new SDHC card at address e624
mmcblk0: mmc0:e624 SU04G 3.69 GiB
 mmcblk0: p1 p2 p3
libphy: 63fec000.etherne:00 - Link is Down
libphy: 63fec000.etherne:00 - Link is Up - 100/Full
root@freescale /$
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>