- 27 Jul, 2010 40 commits
-
-
James Smart authored
- Prevent unregistring of unused FCF when FLOGI is pending. - Prevent point to point discovery on a FCoE HBA. - Fixed FCF discovery failure after swapping FCoE port by switching over to fast failover method when no FCF matches in-use FCF. Signed-off-by:
Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
James Smart authored
- Allow enabling MSI-X intterupts with fewer vectors than requested by looking at the return value from pci_enable_msix. - Implemented driver PCI AER error handling routines for supporting AER error recovering on SLI4 devices. - Remove redundant SLI_ACTIVE checks Signed-off-by:
-
Anil Ravindranath authored
1. MSI-X interrupt support 2. Driver changes to support new maxRAID controller FW version. The changes are mainly done to handle async notification changes done in newer controller FW version. 3. Added state change notifications to notify applications of controller states. Signed-off-by:
Anil Ravindranath <anil_ravindranath@pmc-sierra.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
- Change the Max receive size on CIN FCFs to 0x800 - (From linux community) Check boundary before checking for NULL. - Update last completion time for completed I/O to prevent heartbeat. - Add Balius PCI Device IDs Signed-off-by:
-
James Smart authored
- Fix hba_queue_depth to reflect actual available XRIs - Add support for new SLER specific firmware status codes. - Free SCSI buffer when iotag allocation fails. Signed-off-by:
-
James Smart authored
- Add poll or wait flag parameter to hba_init_link and hba_down_link. - (From Linux Community) Make return with ENXIO negative. - Remove unused INB code from driver. - Prevent block_magmt_io from returning until mailbox is inactive. Signed-off-by:
-
James Smart authored
- Retry PLOGI up to 48 times when LS_RJT reason is "Unable to supply requested data." - When dev loss timeout occures do not change state if there is an outstanding REG_LOGIN. - Add logic to ignore REG_LOGIN completion if discovery is restarted while waiting for REG_LOGIN. - Only change state on REG_LOGIN completion if still in state waiting for REG_LOGIN completion. - Only send ADISCs to FCP-2 Targets (not Initiators). Signed-off-by:
-
Wayne Boyer authored
A change in the hardware design of the chip for the new adapters changes the default endianness of MMIO operations. This patch adds a register definition which when written to with a predefined value will change the endianness back to what the driver expects. This patch also fixes two problems found during testing. First, the first reserved field in the ipr_hostrcb64_fabirc_desc structure only reserved one byte. The correct amount to reserve is 2 bytes. Second, the reserved field of the ipr_hostrcb64_error structure only reserved 2 bytes. The correct amount to reserve is 16 bytes. Signed-off-by:
Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Julia Lawall authored
The function adpt_i2o_post_wait is called from several places, in some of which, such as adpt_abort, a lock may be held. The functions adpt_i2o_reparse_lct and adpt_i2o_lct_get are called from several places, including adpt_rescan where a lock may be held. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @gfp exists@ identifier fn; position p; @@ fn(...) { ... when != spin_unlock_irqrestore when any GFP_KERNEL@p ... when any } @locked@ identifier gfp.fn; @@ spin_lock_irqsave(...) ... when != spin_unlock_irqrestore fn(...) @depends on locked@ position gfp.p; @@ - GFP_KERNEL@p + GFP_ATOMIC // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Giridhar Malavali authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Andrew Vasquez authored
[SCSI] qla2xxx: For ISP 23xx, select user specified login timeout value if greater than minuimum value(4 secs). Signed-off-by:
-
Giridhar Malavali authored
Signed-off-by:
-
Giridhar Malavali authored
Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Lalit Chandivade authored
Driver was not unprotecting correctly, use correct bits to unprotect the flash on ISP 82xx. Signed-off-by:
-
Santosh Vernekar authored
Outstanding mailbox commands, have no way to recover on f/w hung, and we timeout on waiting for mbx response. This in turn affects the recovery process as follows: - We might already be in dpc while waiting for mbx to complete, so recovery for that pci function will never get invoked. Reset Timeout (10 sec) is far less than mbx timeout (30 sec). - Other mbx cmds will get stuck due to serial mbx access. Solution is to identify fw-hung scenario and handle outstanding mbx commands to have an early-exit instead of waiting for response. Other mbx commands waiting for access will also do an early-exit if fw-hung is still applicable. Signed-off-by:
-
Lalit Chandivade authored
After topology change ISP is reset and VPs are re-enabled. If the topology is not fabric, VPs could falsely get enabled. Signed-off-by:
-
Harish Zunjarrao authored
Used bootloder address from FLT while loading FW from flash as well. Signed-off-by:
-
Andrew Vasquez authored
In case of both target and initiator capabilities reported by fc port, the fc port port capability is made mutualy exclusive with priority given for target capabilities. Signed-off-by:
-
Sarang Radke authored
Signed-off-by:
-
Giridhar Malavali authored
Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Andrew Vasquez authored
* hold the hardware_lock throughout the duration of ctx-sp timeout handling -- could result in use-after-free oops. * retry a timed-out login-request. * done() routines are called with the hardware-lock held, issue qla2x00_mark_device_lost() with proper 'defer' flag. * FCP2 capabilities are only relevant to target devices. Signed-off-by:
-
Giridhar Malavali authored
Hold a reference to the srb (sp) while aborting an I/O -- as the I/O can/will complete from within the interrupt-context. Signed-off-by:
-
Giridhar Malavali authored
The TMFs used for pre-24xx ISPs incorrectly assumed 'cpu' tag data could be valid. These chips have no multi-q/cpu-affinity support. This corrects an oops seen on ISP23xx parts. Signed-off-by:
-
Andrew Vasquez authored
This helps to correlate submission/completion messages during triaging. Signed-off-by:
-
Giridhar Malavali authored
The CRB drive active register is cleared when driver is unloaded or when driver enters failed state. Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
-
Stephen M. Cameron authored
We have 32 (MAXSGENTRIES) scatter gather elements embedded in the command. With all these, the total command size is about 576 bytes. However, the last entry in the block fetch table is 35. (the block fetch table contains the number of 16-byte chunks the firmware needs to fetch for a given number of scatter gather elements.) 35 * 16 = 560 bytes, which isn't enough. It needs to be 36. (36 * 16 == 576) or, MAXSGENTRIES + 4. (plus 4 because there's a bunch of stuff at the front of the command before the first scatter gather element that takes up 4 * 16 bytes.) Without this fix, the controller may have to perform two DMA operations to fetch the command since the first one may not get the whole thing. Signed-off-by:
Don Brace <brace@beardog.cce.hp.com> Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
before trying to enter simple mode transport method. Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
