Pull networking fixes from David Miller:
 "Several small bug fixes all over:

   1) be2net driver uses wrong payload length when submitting MAC list
      get requests to the chip.  From Sathya Perla.

   2) Fix mwifiex memory leak on driver unload, from Amitkumar Karwar.

   3) Prevent random memory access in batman-adv, from Marek Lindner.

   4) batman-adv doesn't check for pskb_trim_rcsum() errors, also from
      Marek Lindner.

   5) Fix fec crashes on rapid link up/down, from Frank Li.

   6) Fix inner protocol grovelling in GSO, from Pravin B Shelar.

   7) Link event validation fix in qlcnic from Rajesh Borundia.

   8) Not all FEC chips can support checksum offload, fix from Shawn
      Guo.

   9) EXPORT_SYMBOL + inline doesn't make any sense, from Denis Efremov.

  10) Fix race in passthru mode during device removal in macvlan, from
      Jiri Pirko.

  11) Fix RCU hash table lookup socket state race in ipv6, leading to
      NULL pointer derefs, from Eric Dumazet.

  12) Add several missing HAS_DMA kconfig dependencies, from Geert
      Uyttterhoeven.

  13) Fix bogus PCI resource management in 3c59x driver, from Sergei
      Shtylyov.

  14) Fix info leak in ipv6 GRE tunnel driver, from Amerigo Wang.

  15) Fix device leak in ipv6 IPSEC policy layer, from Cong Wang.

  16) DMA mapping leak fix in qlge from Thadeu Lima de Souza Cascardo.

  17) Missing iounmap on probe failure in bna driver, from Wei Yongjun."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
  bna: add missing iounmap() on error in bnad_init()
  qlge: fix dma map leak when the last chunk is not allocated
  xfrm6: release dev before returning error
  ipv6,gre: do not leak info to user-space
  virtio_net: use default napi weight by default
  emac: Fix EMAC soft reset on 460EX/GT
  3c59x: fix PCI resource management
  caif: CAIF_VIRTIO should depend on HAS_DMA
  net/ethernet: MACB should depend on HAS_DMA
  net/ethernet: ARM_AT91_ETHER should depend on HAS_DMA
  net/wireless: ATH9K should depend on HAS_DMA
  net/ethernet: STMMAC_ETH should depend on HAS_DMA
  net/ethernet: NET_CALXEDA_XGMAC should depend on HAS_DMA
  ipv6: do not clear pinet6 field
  macvlan: fix passthru mode race between dev removal and rx path
  ipv4: ip_output: remove inline marking of EXPORT_SYMBOL functions
  net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode
  net/mlx4_core: Add missing report on VST and spoof-checking dev caps
  net: fec: enable hardware checksum only on imx6q-fec
  qlcnic: Fix validation of link event command.
  ...

Add the missing iounmap() before return from bnad_init()
in the error handling case.
Introduced by commit 01b54b14
(bna: tx rx cleanup fix).
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge allocates chunks from a page that it maps and unmaps that page when
the last chunk is released. When the driver is unloaded or the card is
removed, all chunks are released and the page is unmapped for the last
chunk.

However, when the last chunk of a page is not allocated and the device
is removed, that page is not unmapped. In fact, its last reference is
not put and there's also a page leak. This bug prevents a device from
being properly hotplugged.

When the DMA API debug option is enabled, the following messages show
the pending DMA allocation after we remove the driver.

This patch fixes the bug by unmapping and putting the page from the ring
if its last chunk has not been allocated.

pci 0005:98:00.0: DMA-API: device driver has pending DMA allocations while released from device [count=1]
One of leaked entries details: [device address=0x0000000060a80000] [size=65536 bytes] [mapped with DMA_FROM_DEVICE] [mapped as page]
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:746
Modules linked in: qlge(-) rpadlpar_io rpaphp pci_hotplug fuse [last unloaded: qlge]
NIP: c0000000003fc3ec LR: c0000000003fc3e8 CTR: c00000000054de60
REGS: c0000003ee9c74e0 TRAP: 0700   Tainted: G           O  (3.7.2)
MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI>  CR: 28002424  XER: 00000001
SOFTE: 1
CFAR: c0000000007a39c8
TASK = c0000003ee8d5c90[8406] 'rmmod' THREAD: c0000003ee9c4000 CPU: 31
GPR00: c0000000003fc3e8 c0000003ee9c7760 c000000000c789f8 00000000000000ee
GPR04: 0000000000000000 00000000000000ef 0000000000004000 0000000000010000
GPR08: 00000000000000be c000000000b22088 c000000000c4c218 00000000007c0000
GPR12: 0000000028002422 c00000000ff26c80 0000000000000000 000001001b0f1b40
GPR16: 00000000100cb9d8 0000000010093088 c000000000cdf910 0000000000000001
GPR20: 0000000000000000 c000000000dbfc00 0000000000000000 c000000000dbfb80
GPR24: c0000003fafc9d80 0000000000000001 000000000001ff80 c0000003f38f7888
GPR28: c000000000ddfc00 0000000000000400 c000000000bd7790 c000000000ddfb80
NIP [c0000000003fc3ec] .dma_debug_device_change+0x22c/0x2b0
LR [c0000000003fc3e8] .dma_debug_device_change+0x228/0x2b0
Call Trace:
[c0000003ee9c7760] [c0000000003fc3e8] .dma_debug_device_change+0x228/0x2b0 (unreliable)
[c0000003ee9c7840] [c00000000079a098] .notifier_call_chain+0x78/0xf0
[c0000003ee9c78e0] [c0000000000acc20] .__blocking_notifier_call_chain+0x70/0xb0
[c0000003ee9c7990] [c0000000004a9580] .__device_release_driver+0x100/0x140
[c0000003ee9c7a20] [c0000000004a9708] .driver_detach+0x148/0x150
[c0000003ee9c7ac0] [c0000000004a8144] .bus_remove_driver+0xc4/0x150
[c0000003ee9c7b60] [c0000000004aa58c] .driver_unregister+0x8c/0xe0
[c0000003ee9c7bf0] [c0000000004090b4] .pci_unregister_driver+0x34/0xf0
[c0000003ee9c7ca0] [d000000002231194] .qlge_exit+0x1c/0x34 [qlge]
[c0000003ee9c7d20] [c0000000000e36d8] .SyS_delete_module+0x1e8/0x290
[c0000003ee9c7e30] [c0000000000098d4] syscall_exit+0x0/0x94
Instruction dump:
7f26cb78 e818003a e87e81a0 e8f80028 e9180030 796b1f24 78001f24 7d6a5a14
7d2a002a e94b0020 483a7595 60000000 <0fe00000> 2fb80000 40de0048 80120050
---[ end trace 4294f9abdb01031d ]---
Mapped at:
 [<d000000002222f54>] .ql_update_lbq+0x384/0x580 [qlge]
 [<d000000002227bd0>] .ql_clean_inbound_rx_ring+0x300/0xc60 [qlge]
 [<d0000000022288cc>] .ql_napi_poll_msix+0x39c/0x5a0 [qlge]
 [<c0000000006b3c50>] .net_rx_action+0x170/0x300
 [<c000000000081840>] .__do_softirq+0x170/0x300
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Jitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull spi updates from Mark Brown:
 "A few driver specific fixes plus improved error handling in the
  generic DT GPIO chipselect handling - not exciting but useful."

* tag 'spi-v3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi/spi-atmel: BUG: fix doesn' support 16 bits transfers using PIO
  spi/davinci: fix module build error
  spi: Return error from of_spi_register_master on bad "cs-gpios" property
  spi: Initialize cs_gpio and cs_gpios with -ENOENT
  spi/atmel: fix speed_hz check in atmel_spi_transfer()

Pull drm fixes from Dave Airlie:
 "Just a few straggling fixes I hoovered up, and an intel fixes pull
  from Daniel which fixes some regressions, and some mgag200 fixes from
  Matrox."

* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
  drm/mgag200: Fix framebuffer base address programming
  drm/mgag200: Convert counter delays to jiffies
  drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
  drm/mgag200: Don't change unrelated registers during modeset
  drm: Only print a debug message when the polled connector has changed
  drm: Make the HPD status updates debug logs more readable
  drm: Use names of ioctls in debug traces
  drm: Remove pointless '-' characters from drm_fb_helper documentation
  drm: Add kernel-doc for drm_fb_helper_funcs->initial_config
  drm: refactor call to request_module
  drm: Don't prune modes loudly when a connector is disconnected
  drm: Add missing break in the command line mode parsing code
  drm/i915: clear the stolen fb before resuming
  Revert "drm/i915: Calculate correct stolen size for GEN7+"
  drm/i915: hsw: fix link training for eDP on port-A
  Revert "drm/i915: revert eDP bpp clamping code changes"
  drm: don't check modeset locks in panic handler
  drm/i915: Fix pipe enabled mask for pipe C in WM calculations
  drm/mm: fix dump table BUG
  drm/i915: Always normalize return timeout for wait_timeout_ioctl

Pull virtio/lguest fixes from Rusty Russell:
 "Missing license tag and some fallout from the lguest pagetable rework"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  lguest: clear cached last cpu when guest_set_pgd() called.
  Add missing module license tag to vring helpers.

Higher bits of the base address of framebuffers weren't being
programmed properly. This caused framebuffers that didn't happen to be
allocated at a low enough address to not be displayed properly.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The original line,
  WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp);
wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where
MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into
MGA1064_PIX_CLK_CTL. Change the line to write properly into
MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use
the same pattern (but work correctly), so this patch updates them all
to use this new (slightly more efficient) write pattern. The WREG_DAC
macro was causing the DAC_INDEX register to be set to the same value
twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX
is already at the value we want.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Registers in indices below 0x18 are totally unrelated to modesetting,
so don't write 0's, or anything else into them on modeset. Most of
these registers are hardware cursor related, so this existing code
interferes with hardware cursor development.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Instead of just printing "status updated from 1 to 2", make those enum
numbers immediately readable.

v2: Also patch output_poll_execute() (Daniel Vetter)
v3: Use drm_get_connector_status_name (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (for v1)
Signed-off-by: Dave Airlie <airlied@redhat.com>

We forget to call dev_put() on error path in xfrm6_fill_dst(),
its caller doesn't handle this.

Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a hole in struct ip6_tnl_parm2, so we have to
zero the struct on stack before copying it to user-space.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
we warn drivers when they use napi weight higher than NAPI_POLL_WEIGHT,
but virtio_net still uses 128 by default. This patch makes its default
value to NAPI_POLL_WEIGHT.

Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix EMAC soft reset on 460EX/GT to select the right PHY clock source
before and after the soft reset.

EMAC with PHY should use the clock from PHY during soft reset.
EMAC without PHY should use the internal clock during soft reset.

PPC460EX/GT Embedded Processor Advanced User's Manual
section 28.10.1 Mode Register 0 (EMACx_MR0) states:
Note: The PHY must provide a TX Clk in order to perform a soft reset
of the EMAC. If none is present, select the internal clock
(SDR0_ETH_CFG[EMACx_PHY_CLK] = 1).
After a soft reset, select the external clock.

Without the fix, 460EX/GT-based boards with RGMII PHYs attached to
EMACs experience EMAC interrupt storm and system watchdog reset when
issuing "ifconfig eth0 down" + "ifconfig eth0 up" a few times.
The system enters endless loop of serving emac_irq() with EMACx_ISR
register stuck at value 0x10000000 (Rx parity error).

With the fix, the above issue is no longer observed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver wrongly claimed I/O ports at an address returned by pci_iomap() --
even if it was passed an MMIO address.  Fix this by claiming/releasing all PCI
resources in the PCI driver's probe()/remove() methods instead and get rid of
'must_free_region' flag weirdness (why would Cardbus claim anything for us?).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull tracing/kprobes update from Steven Rostedt:
 "The majority of these changes are from Masami Hiramatsu bringing
  kprobes up to par with the latest changes to ftrace (multi buffering
  and the new function probes).

  He also discovered and fixed some bugs in doing so.  When pulling in
  his patches, I also found a few minor bugs as well and fixed them.

  This also includes a compile fix for some archs that select the ring
  buffer but not tracing.

  I based this off of the last patch you took from me that fixed the
  merge conflict error, as that was the commit that had all the changes
  I needed for this set of changes."

* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/kprobes: Support soft-mode disabling
  tracing/kprobes: Support ftrace_event_file base multibuffer
  tracing/kprobes: Pass trace_probe directly from dispatcher
  tracing/kprobes: Increment probe hit-count even if it is used by perf
  tracing/kprobes: Use bool for retprobe checker
  ftrace: Fix function probe when more than one probe is added
  ftrace: Fix the output of enabled_functions debug file
  ftrace: Fix locking in register_ftrace_function_probe()
  tracing: Add helper function trace_create_new_event() to remove duplicate code
  tracing: Modify soft-mode only if there's no other referrer
  tracing: Indicate enabled soft-mode in enable file
  tracing/kprobes: Fix to increment return event probe hit-count
  ftrace: Cleanup regex_lock and ftrace_lock around hash updating
  ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
  ftrace: Have ftrace_regex_write() return either read or error
  tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
  tracing: Don't succeed if event_enable_func did not register anything
  ring-buffer: Select IRQ_WORK

If NO_DMA=y:

drivers/built-in.o: In function `cfv_destroy_genpool':
drivers/net/caif/caif_virtio.c:364: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `cfv_create_genpool':
drivers/net/caif/caif_virtio.c:397: undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `macb_free_consistent':
drivers/net/ethernet/cadence/macb.c:878: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:883: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:888: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `macb_alloc_consistent':
drivers/net/ethernet/cadence/macb.c:905: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `macb_tx_interrupt':
drivers/net/ethernet/cadence/macb.c:515: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_tx_error_task':
drivers/net/ethernet/cadence/macb.c:457: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_start_xmit':
drivers/net/ethernet/cadence/macb.c:838: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `at91ether_start':
drivers/net/ethernet/cadence/at91_ether.c:49: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/cadence/at91_ether.c:60: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `at91ether_interrupt':
drivers/net/ethernet/cadence/at91_ether.c:250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `at91ether_start_xmit':
drivers/net/ethernet/cadence/at91_ether.c:169: undefined reference to `dma_map_single'
drivers/built-in.o: In function `at91ether_close':
drivers/net/ethernet/cadence/at91_ether.c:145: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `ath9k_beacon_generate':
drivers/net/wireless/ath/ath9k/beacon.c:146: undefined reference to `dma_unmap_single'
drivers/net/wireless/ath/ath9k/beacon.c:174: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/beacon.c:176: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath9k_beacon_remove_slot':
drivers/net/wireless/ath/ath9k/beacon.c:252: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_descdma_setup':
drivers/net/wireless/ath/ath9k/init.c:382: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_edma_get_buffers':
drivers/net/wireless/ath/ath9k/recv.c:616: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_get_next_rx_buf':
drivers/net/wireless/ath/ath9k/recv.c:740: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_edma_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:176: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:340: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_buf_link':
drivers/net/wireless/ath/ath9k/recv.c:122: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_tasklet':
drivers/net/wireless/ath/ath9k/recv.c:1275: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:1277: undefined reference to `dma_mapping_error'
drivers/net/wireless/ath/ath9k/recv.c:1283: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_init':
drivers/net/wireless/ath/ath9k/recv.c:226: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:229: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_rx_init':
drivers/net/wireless/ath/ath9k/recv.c:303: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:306: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_tx_complete_buf':
drivers/net/wireless/ath/ath9k/xmit.c:2088: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_txstatus_setup':
drivers/net/wireless/ath/ath9k/xmit.c:2344: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_tx_set_retry':
drivers/net/wireless/ath/ath9k/xmit.c:307: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_tx_setup_buffer':
drivers/net/wireless/ath/ath9k/xmit.c:1887: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/xmit.c:1889: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `dma_free_tx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1141: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `dma_free_rx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1120: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `free_dma_desc_resources':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1159: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `stmmac_init_rx_buffers':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:980: undefined reference to `dma_map_single'
drivers/built-in.o: In function `init_dma_desc_rings':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1015: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `stmmac_tx_clean':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2044: undefined reference to `dma_unmap_single'
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2082: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx_refill':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1967: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_xmit':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1845: undefined reference to `dma_map_single'
drivers/built-in.o: In function `skb_frag_dma_map':
include/linux/skbuff.h:2184: undefined reference to `dma_map_page'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/ring_mode.c:40: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:48: undefined reference to `dma_map_single'
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:55: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `xgmac_xmit':
drivers/net/ethernet/calxeda/xgmac.c:1102: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

We have seen multiple NULL dereferences in __inet6_lookup_established()

After analysis, I found that inet6_sk() could be NULL while the
check for sk_family == AF_INET6 was true.

Bug was added in linux-2.6.29 when RCU lookups were introduced in UDP
and TCP stacks.

Once an IPv6 socket, using SLAB_DESTROY_BY_RCU is inserted in a hash
table, we no longer can clear pinet6 field.

This patch extends logic used in commit fcbdf09d
("net: fix nulls list corruptions in sk_prot_alloc")

TCP/UDP/UDPLite IPv6 protocols provide their own .clear_sk() method
to make sure we do not clear pinet6 field.

At socket clone phase, we do not really care, as cloning the parent (non
NULL) pinet6 is not adding a fatal race.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, if macvlan in passthru mode is created and data are rxed and
you remove this device, following panic happens:

NULL pointer dereference at 0000000000000198
IP: [<ffffffffa0196058>] macvlan_handle_frame+0x153/0x1f7 [macvlan]

I'm using following script to trigger this:
<script>
while [ 1 ]
do
	ip link add link e1 name macvtap0 type macvtap mode passthru
	ip link set e1 up
	ip link set macvtap0 up
	IFINDEX=`ip link |grep macvtap0 | cut -f 1 -d ':'`
	cat /dev/tap$IFINDEX  >/dev/null &
	ip link del dev macvtap0
done
</script>

I run this script while "ping -f" is running on another machine to send
packets to e1 rx.

Reason of the panic is that list_first_entry() is blindly called in
macvlan_handle_frame() even if the list was empty. vlan is set to
incorrect pointer which leads to the crash.

I'm fixing this by protecting port->vlans list by rcu and by preventing
from getting incorrect pointer in case the list is empty.

Introduced by: commit eb06acdc "macvlan: Introduce 'passthru' mode to takeover the underlying device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Included changes:
- fix parsing of user typed protocol string to avoid random memory access in
  some cases
- check pskb_trim_rcsum() return value
- prevent DAT from sending ARP replies when not needed
- reorder the main clean up routine to prevent race conditions
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 - More fixes in the vCPU PVHVM hotplug path.
 - Add more documentation.
 - Fix various ARM related issues in the Xen generic drivers.
 - Updates in the xen-pciback driver per Bjorn's updates.
 - Mask the x2APIC feature for PV guests.

* tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/pci: Used cached MSI-X capability offset
  xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
  xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST
  xen: mask x2APIC feature in PV
  xen: SWIOTLB is only used on x86
  xen/spinlock: Fix check from greater than to be also be greater or equal to.
  xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info
  xen/vcpu: Document the xen_vcpu_info and xen_vcpu
  xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.

EXPORT_SYMBOL and inline directives are contradictory to each other.
The patch fixes this inconsistency.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure that the following steps are taken:

- drop packets sent by the VF with vlan tag
- block packets with vlan tag which are steered to the VF
- drop/block tagged packets when the policy is priority-tagged
- make sure VLAN stripping for received packets is set
- make sure force UP bit for the VF QP is set

Use enum values for all the above instead of numerical bit offsets.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commits e6b6a231 "net/mlx4: Add VF MAC spoof checking support" and
3f7fb021 "net/mlx4: Add set VF default vlan ID and priority support"
missed reporting in the device capabilities dump when these features
are actually supported. Also two too noisy debug messages which produce
message on every QP opened by a VF, were left in the code, fix that.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration.)
enables hardware checksum acceleration unconditionally for all fec
variants.  This is inappropriate, because some variants like imx5 have
no such support on hardware.  Consequently, fec is broken on these
platforms.  Fix it by enabling hardware checksum only on imx6q-fec type
of controllers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
This patch series has following bug fixes:
* Fix a bug in unicast MAC address setting in adapter.
  Driver was not deleting older unicast MAC while adding new one.
* Fix an ethtool stats string array by adding missing string entry
  and fix a typo.
* Fix module paramter description. Bracket ')' was missing.
* Fix port status provided though 'ethtool <device>' for 83xx adapter.
* Fix reset recovery path in case of transmit timeout.
* Fix reset recovery during diagnostic tests by preserving
  current device status information.
* Fix mailbox response handling. Driver was not maintaining poll time properly.
* Fix validation of link event command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

o VF driver that has enabled asynchronous link events
  may not set BIT_8 in the request, if it does not require
  link state in the response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Fix mailbox response poll time to maximum 5 seconds which
  includes mailbox response time as well as time required for
  processing AEN if any.
o Driver need to read firmware control mailbox register instead
  of host control mailbox register.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o In order to perform reset recovery during diagnostics tests,
  current device status information need to be preserved.
  This patch makes the required changes in diagnostics routines
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o When transmit timeout happens, recovery attempt should start with
  adapter soft reset. If soft reset fails to resume traffic, firmware
  dump will be collected and driver will perform a hard reset of the
  adapter. Reset recovery on 83xx was failing after a hard reset.
  This patch fixes that issue.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>