This reverts commit b72a7e0f.

It causes a dead loop in dml_prefetch_check.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Qili Lu <qili.lu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
For video mode test pattern (i.e. test pattern disable), the call to
rebuild test pattern params for the pipe is skipped. This causes
dynamic disablement of test pattern to not work, as the
test_pattern_params of the pipe will not be updated and retain the
values of the previously enabled test pattern.

[How]
Rebuild test pattern params even when test pattern is video mode,
allowing the pipe to have updated test_pattern_params values.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
OLED panels show no display for large vtotal timings.

[How]
Check if ss is enabled and read from lut for spread spectrum percentage.
Adjust dprefclk as required. DP_DTO adjustment is for edp only.

Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zhongwei <zhongwei.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The previous check for the is_vsc_sdp_colorimetry_supported flag
for MST sink signals did nothing. Simplify the code and use the
same check for MST and SST.

Cc: stable@vger.kernel.org
Reviewed-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

In order for display colorimetry to work correctly on DP displays
we need to send the VSC SDP packet. We should only do so for
panels with DPCD revision greater or equal to 1.4 as older
receivers might have problems with it.

Cc: stable@vger.kernel.org
Cc: Joshua Ashton <joshua@froggi.es>
Cc: Xaver Hugl <xaver.hugl@gmail.com>
Cc: Melissa Wen <mwen@igalia.com>
Cc: Agustin Gutierrez <Agustin.Gutierrez@amd.com>
Reviewed-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
dwb was not POR previosly.
now need to enable dwb in dml2.

Limitation:
HW DML assumes only one DWB
one set of watermark for all 4 watermark sets
one stream has one DWB only.
WB scaling dml input has one set of scaling tap.
(no chroma so far)

needs to follow up
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

why and how:
as part of cleanup, need to refactor vpg. It was improperly referenced
as a dcn specfic part of link. the dcn agnostic code needed was ripped out
and put into vpg.h, now in dc/inc/hw.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Parandhaman K <parandhaman.k@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
6.75 Gbps link rate training for DP_TEST_LINK_RATE_RATE_8
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Allen Pan <allen.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Wrong logic cause screen corruption.

[How]
Port logic from DCN35/314.

Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Fudongwang <fudong.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY&HOW]
We should not be recursively calling the manual trigger programming function when
FAMS is not in use.

Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY&HOW]
Changes to support future versions of FAMS.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Setting soft max frequency for MCLK is allowed in 1VF mode in SMUv13.0.6
SOCs.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
When Subvp pipe's index is smaller than main pipe's index, the main
pipe's ODM policy is not yet assigned. If we assign subvp pipe's ODM
policy based on main pipe, we will assign uninitialized ODM policy.

[how]
Instead of copying main pipe's policy we copy the main pipe ODM policy
logic. So it doesn't matter whether if main pipe's ODM policy is set,
phantom pipe will always have the same policy because it running the
same calcualtion to derive ODM policy.

Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
In current implemenation ODM mode is only reset when the last plane is
removed from dc state. For any dc validate we will always remove all
current planes and add new planes. However when switching from no planes
to 1 plane, ODM mode is not reset because no planes get removed. This
has caused an issue where we kept ODM combine when it should have been
remove when a plane is added. The change is to reset ODM mode when
adding the first plane.

Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The RB bitmap should be global active RB bitmap &
active RB bitmap based on active SA.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

mode_config's max width x height is 4096x2160 and is higher than DWB's
max resolution 3840x2160 which is returned instead.

Cc: stable@vger.kernel.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We want flexibility to choose how pwrseq instance is mapped to eDP panel

[How]
Add configuration option to choose the pwrseq mapping policy.
When enabled, allow fixed mapping between DIG inst to pwrseq inst.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1. change AMDGPU_VF2PF_UPDATE_MAX_RETRY_LIMIT from 30 to 5.
2. set fatel error detected flag.
Signed-off-by: Zhigang Luo <Zhigang.Luo@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If there are more than one device doing reset in parallel, the first
device will call kfd_suspend_all_processes() to evict all processes
on all devices, this call takes time to finish. other device will
start reset and recover without waiting. if the process has not been
evicted before doing recover, it will be restored, then caused page
fault.
Signed-off-by: Zhigang Luo <Zhigang.Luo@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Set RAS priority handling capability for SMUv13.0.6 SOCs and categorize
RAS priority messages allowed.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When a RAS fatal error is detected, PMFW will only process priority
messages. Other messages won't be taken up for processing and therefore
won't get any response in such a state.

Add logic to filter out non-priority messages when RAS error is
detected. Also, don't poll response response status register before
sending priority messages. Use firmware capability flag to determine
whether to filter priority messages.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add flags to categorize messages and PMFW capabilities.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

In case of fatal errors, set FED status when interrupt is received. Set
the flag on other devices in the hive before RAS recovery work.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This commit removes the lines that describe the 'streams'
and 'stream_count' parameters and adds a line to describe the 'params'
parameter, which was missing from the original comment block.

Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2138: warning: Function parameter or member 'params' not described in 'dc_commit_streams'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2138: warning: Excess function parameter 'streams' description in 'dc_commit_streams'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2138: warning: Excess function parameter 'stream_count' description in 'dc_commit_streams'

Fixes: e779f458 ("drm/amd/display: Add handling for DC power mode")
Cc: Joshua Aberback <joshua.aberback@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use OD (pp_od_clk_voltage) interface to report current limits,
default or those set by user, for SCLK and UCLK on aldebaran.
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use OD (pp_od_clk_voltage) interface to report current limits,
default or those set by user, for SCLK and UCLK on smu_v_13_0_6
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
set_q_mode_offs don't get cleared after GPU reset, nexting SET_Q_MODE
packet to init shadow memory will be skiped, hence there has a page fault.

[How]
VM flush is needed after GPU reset, clear set_q_mode_offs when
emitting VM flush.

Fixes: 8bc75586 ("drm/amdgpu: workaround to avoid SET_Q_MODE packets v2")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: ZhenGuo Yin <zhenguo.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

RAS TA will handle it, the function is useless.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

support MES command SET_HW_RESOURCE1 in sriov
Signed-off-by: chongli2 <chongli2@amd.com>
Reviewed-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Acked-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Check more possible ext error codes.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add more possible ext error code.

v2: still use ext error code instead of UC bit.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

VCN need not be shared in CPX mode always for all GFX 9.4.3 SOC SKUs. In
certain configs, VCN instance can be exclusively allocated to a
partition even under CPX mode.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Check AMDGPU_RUNPM_BAMACO intead of amdgpu_runtime_pm
when setting baco state.
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Optimize the code to add support for BAMACO mode checking
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

centralize all pp_dpm_xxx attr nodes into
pp_dpm_clk_default_attr_update() function.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

ASD is not needed by headless GPU.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support for MACO flag checking.
MACO mode only works if BACO is supported.
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use a unified and more explicit name get_bamaco_support
to replace is_baco_support and get_asic_baco_capability
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add a new runtime pm mode AMDGPU_RUNPM_BAMACO
and related macro definition
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

fix the high voltage issue after unload on smu 13.0.10
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>