- 19 Nov, 2014 22 commits
-
-
Yoshifumi Hosoya authored
Signed-off-by:
Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au>
-
Kouei Abe authored
Signed-off-by:
Kouei Abe <kouei.abe.cp@renesas.com> Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Geert Uytterhoeven authored
The LEDs on the kzm9g board are labeled using upper-case characters. Signed-off-by:
-
Geert Uytterhoeven authored
The LEDs on the koelsch board are labeled using upper-case characters. Signed-off-by:
-
Geert Uytterhoeven authored
The IIC nodes used the generic compatible properties only. This causes the driver to fail when using Standard Speed, as the operational clock is driven by the 104 MHz HP clock: i2c-sh_mobile e6820000.i2c: timing values out of range: L/H=0x208/0x1bf i2c-sh_mobile: probe of e6820000.i2c failed with error -22 Add the SoC-specific compatible property to fix this. Signed-off-by: -
Geert Uytterhoeven authored
The IIC nodes used the generic compatible properties only. This may cause the driver to fail when using Standard Speed on IIC masters where the operational clock is driven by the 130 MHz HP clock. Add the SoC-specific compatible property to fix this. Signed-off-by:
-
Kuninori Morimoto authored
DMA transfer uses DVC DMA DMApp [MEM] -> [SRC] -> [DVC] -> [SSIU] -> [SSI] DMA DMApp [MEM] <- [DVC] <- [SRC] <- [SSIU] <- [SSI] Signed-off-by: -
Kuninori Morimoto authored
DMA transfer to/from SRC DMA DMApp [MEM] -> [SRC] -> [SSIU] -> [SSI] DMA DMApp [MEM] <- [SRC] <- [SSIU] <- [SSI] Current sound driver is supporting SSI/SRC random connection. So, this patch is tring SSI0 -> SRC2 SSI1 <- SRC3 Signed-off-by: -
Kuninori Morimoto authored
DMA transfer to/from SSIU DMA [MEM] -> [SSIU] -> [SSI] DMA [MEM] <- [SSIU] <- [SSI] Signed-off-by: -
Kuninori Morimoto authored
DMA transfer to/from SSI DMA [MEM] -> [SSI] DMA [MEM] <- [SSI] Signed-off-by: -
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Current Koelsch I2C2 has 400kHz settings, but, ak4643 audio codec chip which is connected to I2C2 can't work such frequency. Fixup I2C2 clock frequency to 100kHz. Signed-off-by:
-
Kuninori Morimoto authored
DMA transfer uses DVC DMA DMApp [MEM] -> [SRC] -> [DVC] -> [SSIU] -> [SSI] DMA DMApp [MEM] <- [DVC] <- [SRC] <- [SSIU] <- [SSI] Signed-off-by: -
Kuninori Morimoto authored
DMA transfer to/from SRC DMA DMApp [MEM] -> [SRC] -> [SSIU] -> [SSI] DMA DMApp [MEM] <- [SRC] <- [SSIU] <- [SSI] Current sound driver is supporting SSI/SRC random connection. So, this patch is tring SSI0 -> SRC2 SSI1 <- SRC3 Signed-off-by: -
Kuninori Morimoto authored
DMA transfer to/from SSIU DMA [MEM] -> [SSIU] -> [SSI] DMA [MEM] <- [SSIU] <- [SSI] Signed-off-by: -
Kuninori Morimoto authored
DMA transfer to/from SSI DMA [MEM] -> [SSI] DMA [MEM] <- [SSI] Signed-off-by: -
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Current Lager IIC2 is using default clock frequency, but, ak4643 audio codec chip needs 100kHz This patch clarifies IIC2 clock frequency as 100kHz. Signed-off-by:
-
- 10 Nov, 2014 4 commits
-
-
Kuninori Morimoto authored
Instantiate the Audio DMAC peri peri controllers in the r8a7791 device tree. Signed-off-by:
-
Kuninori Morimoto authored
Instantiate the Audio DMAC peri peri controllers in the r8a7790 device tree. Signed-off-by:
-
Kuninori Morimoto authored
Instantiate the two Audio DMA controllers in the r8a7791 device tree. Signed-off-by:
-
Kuninori Morimoto authored
Instantiate the two Audio DMA controllers in the r8a7790 device tree. Signed-off-by:
-
- 04 Nov, 2014 1 commit
-
-
Koji Matsuoka authored
Signed-off-by:
Koji Matsuoka <koji.matsuoka.xm@renesas.com> Signed-off-by:
-
- 30 Oct, 2014 13 commits
-
-
Geert Uytterhoeven authored
The SATA node used the generic compatible property only, which was deprecated by commit e67adb4e ("sata_rcar: Add R-Car Gen2 SATA PHY support"). Add the SoC-specific one introduced by that commit. Signed-off-by:
-
Laurent Pinchart authored
Add references to the transmit and receive DMA channels in the MMCIF node. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by:
-
Laurent Pinchart authored
Add references to the transmit and receive DMA channels in the two MMCIF nodes. Signed-off-by:
-
Laurent Pinchart authored
Add the MMCIF0 device to the r8a7791 device tree. Signed-off-by:
-
Laurent Pinchart authored
Node names should describe the function of the device, not its IP core name. Signed-off-by:
-
Geert Uytterhoeven authored
The TMU timers used the generic compatible property only. Add the SoC-specific one, to make it future proof. Signed-off-by:
-
Geert Uytterhoeven authored
The CMT1 timer used the generic compatible property only. Add the SoC-specific one, which is already documented, to make it future proof. Signed-off-by:
-
Yoshihiro Shimoda authored
Enable HS-USB device for the Henninger board, defining the GPIO that the driver should check when probing (which is the ID output from MAX3355 OTG chip). Note that there will be pinctrl-related error messages if both internal PCI and HS-USB drivers are enabled but they should be just ignored. Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> [Sergei: added pin function/group and prop, moved device node, fixed summary, added changelog] Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Yoshihiro Shimoda authored
Enable HS-USB device for the Koelsch board, defining the GPIO that the driver should check when probing (which is the ID output from MAX3355 OTG chip). Note that there will be pinctrl-related error messages if both internal PCI and HS-USB drivers are enabled but they should be just ignored. Signed-off-by:
-
Yoshihiro Shimoda authored
Define the R8A7791 generic part of the HS-USB device node. It is up to the board file to enable the device. Signed-off-by:
-
Yoshihiro Shimoda authored
Enable HS-USB device for the Lager board, defining the GPIO that the driver should check when probing. Since this board doesn't have the OTG ID pin, we assume that GP5_18 (USB0_PWEN) is an ID pin because it is 1 when the SW5 is in position 2-3 (meaning USB function) and 0 in other positions. Note that there will be pinctrl-related error messages if both internal PCI and HS-USB drivers are enabled but they should be just ignored. Signed-off-by:
-
Yoshihiro Shimoda authored
Define the R8A7790 generic part of the HS-USB device node. It is up to the board file to enable the device. Signed-off-by:
-
Yoshihiro Shimoda authored
Signed-off-by:
-
