sent_cmd memory is not freed before freeing hci_dev causing it to leak
it contents.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Obtaining a MAC address may be deferred in cases when the MAC is stored
in an NVMEM block, for example, and it may not be ready upon the first
retrieval attempt and return EPROBE_DEFER.

It is also possible that a port that does not rely on NVMEM has been
already created when getting the defer request. Thus, also the resources
allocated previously must be freed when doing a roll-back.

Fixes: 76723bca ("net: mv643xx_eth: add DT parsing support")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220223142337.41757-1-maukka@ext.kapsi.fiSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().

Fixes: 35a79e64 ("ping: fix the dif and sdif check in ping_lookup")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1ef3f2fcd31bd681a193b1fcf235eee1603819bd.1645674068.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Revert of a patch that instead of fixing a AQ error when trying
to reset BW limit introduced several regressions related to
creation and managing TC. Currently there are errors when creating
a TC on both PF and VF.

Error log:
[17428.783095] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783107] i40e 0000:3b:00.1: Failed configuring TC map 0 for VSI 391
[17428.783254] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783259] i40e 0000:3b:00.1: Unable to  configure TC map 0 for VSI 391

This reverts commit 3d250466.

Fixes: 3d250466 (i40e: Fix reset bw limit when DCB enabled with 1 TC)
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220223175347.1690692-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.

Fix this by updating skb->csum if available.

Trace resulted by ipv6 ttl dec and then sending packet
to conntrack [actions: set(ipv6(hlimit=63)),ct(zone=99)]:
[295241.900063] s_pf0vf2: hw csum failure
[295241.923191] Call Trace:
[295241.925728]  <IRQ>
[295241.927836]  dump_stack+0x5c/0x80
[295241.931240]  __skb_checksum_complete+0xac/0xc0
[295241.935778]  nf_conntrack_tcp_packet+0x398/0xba0 [nf_conntrack]
[295241.953030]  nf_conntrack_in+0x498/0x5e0 [nf_conntrack]
[295241.958344]  __ovs_ct_lookup+0xac/0x860 [openvswitch]
[295241.968532]  ovs_ct_execute+0x4a7/0x7c0 [openvswitch]
[295241.979167]  do_execute_actions+0x54a/0xaa0 [openvswitch]
[295242.001482]  ovs_execute_actions+0x48/0x100 [openvswitch]
[295242.006966]  ovs_dp_process_packet+0x96/0x1d0 [openvswitch]
[295242.012626]  ovs_vport_receive+0x6c/0xc0 [openvswitch]
[295242.028763]  netdev_frame_hook+0xc0/0x180 [openvswitch]
[295242.034074]  __netif_receive_skb_core+0x2ca/0xcb0
[295242.047498]  netif_receive_skb_internal+0x3e/0xc0
[295242.052291]  napi_gro_receive+0xba/0xe0
[295242.056231]  mlx5e_handle_rx_cqe_mpwrq_rep+0x12b/0x250 [mlx5_core]
[295242.062513]  mlx5e_poll_rx_cq+0xa0f/0xa30 [mlx5_core]
[295242.067669]  mlx5e_napi_poll+0xe1/0x6b0 [mlx5_core]
[295242.077958]  net_rx_action+0x149/0x3b0
[295242.086762]  __do_softirq+0xd7/0x2d6
[295242.090427]  irq_exit+0xf7/0x100
[295242.093748]  do_IRQ+0x7f/0xd0
[295242.096806]  common_interrupt+0xf/0xf
[295242.100559]  </IRQ>
[295242.102750] RIP: 0033:0x7f9022e88cbd
[295242.125246] RSP: 002b:00007f9022282b20 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffda
[295242.132900] RAX: 0000000000000005 RBX: 0000000000000010 RCX: 0000000000000000
[295242.140120] RDX: 00007f9022282ba8 RSI: 00007f9022282a30 RDI: 00007f9014005c30
[295242.147337] RBP: 00007f9014014d60 R08: 0000000000000020 R09: 00007f90254a8340
[295242.154557] R10: 00007f9022282a28 R11: 0000000000000246 R12: 0000000000000000
[295242.161775] R13: 00007f902308c000 R14: 000000000000002b R15: 00007f9022b71f40

Fixes: 3fdbd1ce ("openvswitch: add ipv6 'set' action")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Link: https://lore.kernel.org/r/20220223163416.24096-1-paulb@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Niels Dossche <niels.dossche@ugent.be>
Link: https://lore.kernel.org/r/20220223131954.6570-1-niels.dossche@ugent.beSigned-off-by: Jakub Kicinski <kuba@kernel.org>

smc_pnetid_by_table_ib() uses read_lock() and then it calls smc_pnet_apply_ib()
which, in turn, calls mutex_lock(&smc_ib_devices.mutex).

read_lock() disables preemption. Therefore, the code acquires a mutex while in
atomic context and it leads to a SAC bug.

Fix this bug by replacing the rwlock with a mutex.

Reported-and-tested-by: syzbot+4f322a6d84e991c38775@syzkaller.appspotmail.com
Fixes: 64e28b52 ("net/smc: add pnet table namespace support")
Confirmed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220223100252.22562-1-fmdefrancesco@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit b7a49f73 ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.

Fixes: b7a49f73 ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 2afeec08.

The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).

This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.

More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#uSigned-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 1f256578.

The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.

Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.

More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#uSigned-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220222001817.2264967-1-marmarek@invisiblethingslab.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5 fixes 2022-02-22

This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.

* tag 'mlx5-fixes-2022-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5e: Fix VF min/max rate parameters interchange mistake
  net/mlx5e: Add missing increment of count
  net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
  net/mlx5e: Fix MPLSoUDP encap to use MPLS action information
  net/mlx5e: Add feature check for set fec counters
  net/mlx5e: TC, Skip redundant ct clear actions
  net/mlx5e: TC, Reject rules with forward and drop actions
  net/mlx5e: TC, Reject rules with drop and modify hdr action
  net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
  net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
  net/mlx5: Fix possible deadlock on rule deletion
  net/mlx5: Fix tc max supported prio for nic mode
  net/mlx5: Fix wrong limitation of metadata match on ecpf
  net/mlx5: Update log_max_qp value to be 17 at most
  net/mlx5: DR, Fix the threshold that defines when pool sync is initiated
  net/mlx5: DR, Don't allow match on IP w/o matching on full ethertype/ip_version
  net/mlx5: DR, Fix slab-out-of-bounds in mlx5_cmd_dr_create_fte
  net/mlx5: DR, Cache STE shadow memory
  net/mlx5: Update the list of the PCI supported devices
====================

Link: https://lore.kernel.org/r/20220224001123.365265-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The VF min and max rate were passed incorrectly and resulted in wrongly
interchanging them. Fix the order of parameters in
mlx5_esw_qos_set_vport_rate().

Fixes: d7df09f5 ("net/mlx5: E-switch, Enable vport QoS on demand")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add mistakenly missing increment of count variable when looping over
output buffer in mlx5e_self_test().

This resolves the issue of garbage values output when querying with self
test via ethtool.

before:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test        0
Speed Test       1768697188
Health Test      758528120
Loopback Test    3288687

after:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test        0
Speed Test       0
Health Test      0
Loopback Test    0

Fixes: 7990b1b5 ("net/mlx5e: loopback test is not supported in switchdev mode")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently offload of rule on bareudp device require tunnel key
in order to match on mpls fields and without it the mpls fields
are ignored, this is incorrect due to the fact udp tunnel doesn't
have key to match on.

Fix by returning error in case flow is matching on tunnel key.

Fixes: 72046a91 ("net/mlx5e: Allow to match on mpls parameters")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently the MPLSoUDP encap builds the MPLS header using encap action
information (tunnel id, ttl and tos) instead of the MPLS action
information (label, ttl, tc and bos) which is wrong.

Fix by storing the MPLS action information during the flow action
parse and later using it to create the encap MPLS header.

Fixes: f828ca6a ("net/mlx5e: Add support for hw encapsulation of MPLS over UDP")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Fec counters support is checked via the PCAM feature_cap_mask,
bit 0: PPCNT_counter_group_Phy_statistical_counter_group.
Add feature check to avoid faulty behavior.

Fixes: 0a1498eb ("net/mlx5e: Expose FEC counters via ethtool")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Offload of ct clear action is just resetting the reg_c register.
It's done by allocating modify hdr resources which is limited.
Doing it multiple times is redundant and wasting modify hdr resources
and if resources depleted the driver will fail offloading the rule.
Ignore redundant ct clear actions after the first one.

Fixes: 806401c2 ("net/mlx5e: CT, Fix multiple allocations and memleak of mod acts")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Such rules are redundant but allowed and passed to the driver.
The driver does not support offloading such rules so return an error.

Fixes: 03a9d11e ("net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

This kind of action is not supported by firmware and generates a
syndrome.

kernel: mlx5_core 0000:08:00.0: mlx5_cmd_check:777:(pid 102063): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3)

Fixes: d7e75a32 ("net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

For RX TLS device-offloaded packets, the HW spec guarantees checksum
validation for the offloaded packets, but does not define whether the
CQE.checksum field matches the original packet (ciphertext) or
the decrypted one (plaintext). This latitude allows architetctural
improvements between generations of chips, resulting in different decisions
regarding the value type of CQE.checksum.

Hence, for these packets, the device driver should not make use of this CQE
field. Here we block CHECKSUM_COMPLETE usage for RX TLS device-offloaded
packets, and use CHECKSUM_UNNECESSARY instead.

Value of the packet's tcp_hdr.csum is not modified by the HW, and it always
matches the original ciphertext.

Fixes: 1182f365 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The ioctl EEPROM query wrongly returns success on read failures, fix
that by returning the appropriate error code.

Fixes: bb64143e ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add missing call to up_write_ref_node() which releases the semaphore
in case the FTE doesn't have destinations, such in drop rule case.

Fixes: 465e7baa ("net/mlx5: Fix deletion of duplicate rules")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Only prio 1 is supported if firmware doesn't support ignore flow
level for nic mode. The offending commit removed the check wrongly.
Add it back.

Fixes: 9a99c8f1 ("net/mlx5e: E-Switch, Offload all chain 0 priorities when modify header and forward action is not supported")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Match metadata support check returns false for ecpf device.
However, this support does exist for ecpf and therefore this
limitation should be removed to allow feature such as stacked
devices and internal port offloaded to be supported.

Fixes: 92ab1eb3 ("net/mlx5: E-Switch, Enable vport metadata matching if firmware supports it")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, log_max_qp value is dependent on what FW reports as its max capability.
In reality, due to a bug, some FWs report a value greater than 17, even though they
don't support log_max_qp > 17.

This FW issue led the driver to exhaust memory on startup.
Thus, log_max_qp value is set to be no more than 17 regardless
of what FW reports, as it was before the cited commit.

Fixes: f79a609e ("net/mlx5: Update log_max_qp value to FW max capability")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When deciding whether to start syncing and actually free all the "hot"
ICM chunks, we need to consider the type of the ICM chunks that we're
dealing with. For instance, the amount of available ICM for MODIFY_ACTION
is significantly lower than the usual STE ICM, so the threshold should
account for that - otherwise we can deplete MODIFY_ACTION memory just by
creating and deleting the same modify header action in a continuous loop.

This patch replaces the hard-coded threshold with a dynamic value.

Fixes: 1c586514 ("net/mlx5: DR, ICM memory pools sync optimization")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently SMFS allows adding rule with matching on src/dst IP w/o matching
on full ethertype or ip_version, which is not supported by HW.
This patch fixes this issue and adds the check as it is done in DMFS.

Fixes: 26d688e3 ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When adding a rule with 32 destinations, we hit the following out-of-band
access issue:

  BUG: KASAN: slab-out-of-bounds in mlx5_cmd_dr_create_fte+0x18ee/0x1e70

This patch fixes the issue by both increasing the allocated buffers to
accommodate for the needed actions and by checking the number of actions
to prevent this issue when a rule with too many actions is provided.

Fixes: 1ffd4989 ("net/mlx5: DR, Increase supported num of actions to 32")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

During rule insertion on each ICM memory chunk we also allocate shadow memory
used for management. This includes the hw_ste, dr_ste and miss list per entry.
Since the scale of these allocations is large we noticed a performance hiccup
that happens once malloc and free are stressed.
In extreme usecases when ~1M chunks are freed at once, it might take up to 40
seconds to complete this, up to the point the kernel sees this as self-detected
stall on CPU:

 rcu: INFO: rcu_sched self-detected stall on CPU

To resolve this we will increase the reuse of shadow memory.
Doing this we see that a time in the aforementioned usecase dropped from ~40
seconds to ~8-10 seconds.

Fixes: 29cf8feb ("net/mlx5: DR, ICM pool memory allocator")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add the upcoming BlueField-4 and ConnectX-8 device IDs.

Fixes: 2e9d3e83 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Heyi Guo says:

====================
drivers/net/ftgmac100: fix occasional DHCP failure

This patch set is to fix the issues discussed in the mail thread:
https://lore.kernel.org/netdev/51f5b7a7-330f-6b3c-253d-10e45cdb6805@linux.alibaba.com/
and follows the advice from Andrew Lunn.

The first 2 patches refactors the code to enable adjust_link calling reset
function directly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

DHCP failures were observed with systemd 247.6. The issue could be
reproduced by rebooting Aspeed 2600 and then running ifconfig ethX
down/up.

It is caused by below procedures in the driver:

1. ftgmac100_open() enables net interface and call phy_start()
2. When PHY is link up, it calls netif_carrier_on() and then
adjust_link callback
3. ftgmac100_adjust_link() will schedule the reset task
4. ftgmac100_reset_task() will then reset the MAC in another schedule

After step 2, systemd will be notified to send DHCP discover packet,
while the packet might be corrupted by MAC reset operation in step 4.

Call ftgmac100_reset() directly instead of scheduling task to fix the
issue.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to prepare for ftgmac100_adjust_link() to call
ftgmac100_reset() directly. Only code places are changed.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to prepare for ftgmac100_adjust_link() to call reset function
directly, instead of task schedule.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix following coccicheck warning:
./net/sched/act_api.c:277:7-49: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding myself (Alvin Šipraga) as another maintainer for the Realtek DSA
switch drivers. I intend to help Linus out with reviewing and testing
changes to these drivers, particularly the rtl8365mb driver which I
authored and have hardware access to.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer.  In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {".  That's going to work most of the time,
but there is a potential for those to be equal.

Fixes: 1593123a ("tipc: add name table dump to new netlink api")
Fixes: 1a1a143d ("tipc: add publication dump to new netlink api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This test is checking if we exited the list via break or not.  However
if it did not exit via a break then "node" does not point to a valid
udp_tunnel_nic_shared_node struct.  It will work because of the way
the structs are laid out it's the equivalent of
"if (info->shared->udp_tunnel_nic_info != dev)" which will always be
true, but it's not the right way to test.

Fixes: 74cc6d18 ("udp_tunnel: add the ability to share port tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vhost_vsock_stop() calls vhost_dev_check_owner() to check the device
ownership. It expects current->mm to be valid.

vhost_vsock_stop() is also called by vhost_vsock_dev_release() when
the user has not done close(), so when we are in do_exit(). In this
case current->mm is invalid and we're releasing the device, so we
should clean it anyway.

Let's check the owner only when vhost_vsock_stop() is called
by an ioctl.

When invoked from release we can not fail so we don't check return
code of vhost_vsock_stop(). We need to stop vsock even if it's not
the owner.

Fixes: 433fc58e ("VSOCK: Introduce vhost_vsock.ko")
Cc: stable@vger.kernel.org
Reported-by: syzbot+1e3ea63db39f2b4440e0@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+3140b17cb44a7b174008@syzkaller.appspotmail.com
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If client is unable to initiate a failover reset via H_VIOCTL hcall, then
it should schedule a failover reset as a last resort. Otherwise, there is
no need to do a last resort.

Fixes: 334c4241 ("ibmvnic: improve failover sysfs entry")
Reported-by: Cris Forno <cforno12@outlook.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220221210545.115283-1-drt@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>