The APCI3120_DISABLE_ALL_TIMER define define is not needed, and it's used
incorrectly in apci3120_cancel(). The define is a mask of the bits needed
to disable the counters. Writing the value directly sets unintended bits.

Prior to writing the value, the 'devpriv->us_OutputRegister' is set to 0
and written to the register. This disables all the timers and the external
trigger.

Remove the unnecessary apci3120_exttrig_disable() call as well as the write
of APCI3120_DISABLE_ALL_TIMER.

In apci3120_interrupt(), remove the unnecessary mask and write to disable
all the timers. The COMEDI_CB_EOA event will cause the core to call the
(*cancel) operation which will disable the timers.

Remove the unused define.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Define the CTR0 register in the main driver source file and remove all
the old defines in hwrdv_apci3120.c.

For aesthetics, save the raw digital output state (devpriv->do_bits) in
the digital output (*insn_bits) function and use a macro to set them when
reading/writing a timer.

Use the CTR0 register define in the digital output (*insn_bits) function
and remove the current register define.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a helper function to select a timer and read a value from it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a helper function to select a timer and write a value to it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rename this CamelCase member of the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The timer divisor calculations in this driver are over complicated.

There are three timers on the board. They all use the same base clock
with a fixed prescaler for each timer. The base clock used depends on
the board version and type:

  APCI-3120 Rev A boards OSC = 14.29MHz base clock (~70ns)
  APCI-3120 Rev B boards OSC = 20MHz base clock (50ns)
  APCI-3001 boards OSC = 20MHz base clock (50ns)

The prescalers for each timer are:

  Timer 0 CLK = OSC/10
  Timer 1 CLK = OSC/1000
  Timer 2 CLK = OSC/1000

Add a new member to the private data, 'osc_base', to hold the base clock
time. Set this member during the board attach.

Introduce a helper function to calculate the divisor needed to generate
a nanosecond time with a given timer.

Use the new helper function in the driver to clarify the code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

use find_board_by_major function instead of getting a brd from static
arrary. Becasue tty's major number doesn't start zero and we can
find a brd from dgap_board[].
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The board_t has a tty_struct(serial_driver and print_driver)
that has a major number. When major number is compared in
dgap_tty_open(), just use brd->serial_driver{print_driver}->major.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The tty_struct of serial_driver and print_driver were getting
allocated twice. One is allocated in tty_alloc_driver(), the other
is in dgap_tty_register(). So remove these in dgap_tty_register().
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty's flags can be set by calling tty_alloc_driver().
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'count' and use the comedi_async 'scans_done'
member to detect the end-of-acquisition.

Use the comedi_nsamples_left() helper to get the number of samples to actually
add to the async buffer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'count' and use the comedi_async 'scans_done'
member to detect the end-of-acquisition.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'ao_count' and use the comedi_async 'scans_done'
member to detect the analog output end-of-acquisition.

Use the comedi_nsamples_left() helper to get the number of samples to actually
read from the async buffer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'ai_count' and use the comedi_async 'scans_done'
member to detect the analog output end-of-acquisition.

Use the comedi_nsamples_left() helper to get the number of samples to actually
add to the async buffer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'ao_count' and use the comedi_async 'scans_done'
member to detect the analog output end-of-acquisition.

Use the comedi_nsamples_left() helper to get the number of samples to actually
read from the async buffer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'count' and use the comedi_async 'scans_done'
member to detect the analog input end-of-acquisition.

Use the comedi_nsamples_left() helper to get the number of samples to actually
add to the async buffer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'ai_sample_count' and use the comedi_async
'scans_done' member to detect the analog input end-of-acquisition.

Use the comedi_nsamples_left() helper to get the number of samples to actually
add to the async buffer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'ai_scan_count' and use the comedi_async 'scans_done'
member to detect the analog input end-of-acquisition.

Use the comedi_nsamples_left() helper to work out the number of 'wake' samples in
pci230_ai_update_fifo_trigger_level() and the number of 'todo' samples actually
added to the async buffer in pci230_handle_ai().

Remove the unnecessary COMEDI_CB_OVERFLOW event for the hardware FIFO overflow
error. The COMEDI_CB_ERROR event will terminate the command.

comedi_buf_write_samples() can fail if the async buffer does not have room for
the sample. The it will set the COMEDI_CB_OVERFLOW event and return 0. Detect
this and quit trying to read and add more samples. The event will terminate the
command.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a helper function to calculate the number of samples remaining
when the cmd->stop_src is TRIG_COUNT.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'ai_count' and use the comedi_async 'scans_done'
member to detect the analog output end-of-acquisition.

Use the helper function comedi_nscans_left() to get the number of scans in the
async buffer of left in the command.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'ai_count' and use the comedi_async 'scans_done'
member to detect the end-of-acquisition.

Use the helper function comedi_nscans_left() to check if the number of scans
left in the command.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the private data member 'ao_stop_count' and use the comedi_async
'scans_done' member to detect the end-of-acquisition.

Use the helper function comedi_nscans_left() to determine the number of scans
available in the async buffer or left in the command.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a helper function to determine the number of scans left in
the async command.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Setting the `CONFIG_COMEDI_PCI_DRIVERS` kernel configuration option
makes the main "comedi" module depend on the PCI support in the kernel.
That's not that big a deal since PCI support in the kernel is either
built into the kernel or is absent, and is not in a separate module.
Still, not all low-level Comedi drivers need PCI support, so we could
save a bit of space by not including it.  The Comedi PCI support
functions are all in "comedi_pci.c".  Turn it into a separate module so
the support code doesn't have to be loaded unnecessarily.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Setting the `CONFIG_COMEDI_USB_DRIVERS` kernel configuration option
makes the main "comedi" module depend on the "usbcore" module.  But
perhaps the machine has no USB controllers (or they have been disabled),
in which case the "usbcore" module may have been pulled in
unnecessarily.  Only a few low-level Comedi drivers require USB support.
The Comedi USB support functions are all in "comedi_usb.c".  Turn it
into a separate module so we don't have to pull in the "usbcore" and
"usb_common" modules unnecessarily.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Setting the `CONFIG_COMEDI_PCMCIA_DRIVERS` kernel configuration option
makes the main "comedi" module depend on the "pcmcia" module, but many
machines don't have PCMCIA slots and only a few low-level Comedi drivers
need PCMCIA support.  The Comedi PCMCIA support functions are all in
"comedi_pcmcia.c".  Turn it into a separate module so we don't have to
pull in the other PCMCIA support modules unnecessarily.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some declarations and macro definitions in "comedidev.h" are protected
by various `#ifdef`s for kernel configuration options, but the header
file compiles fine without the `#ifdef`s regardless of whether those
config option macros are defined or not.  Remove the `#ifdef`s and
compile the affected code unconditionally.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some low-level Comedi driver modules used to handle PCI devices and ISA
devices in the same module with some conditional compilation.  To reduce
the amount of conditional compilation, some dummy inline versions of
`comedi_to_pci_dev()`, `comedi_pci_enable()`, `comedi_pci_disable()`,
and `comedi_pci_detach()` are defined in "comedidev.h" if
`CONFIG_COMEDI_PCI_DRIVERS` is undefined.  Since those Comedi low-level
driver modules have since had PCI support split out into separate
modules, there is no need to keep the dummy inline functions around any
more, so remove them.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

set by calling CARDbyGetPktType.

change CARDbIsOFDMinBasicRate to check basic_rates.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Changing callers to point to private
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Referencing dwIoBase inside function.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace __iomem with vnt_private providing pointer for dwIoBase

Change BBvPowerSaveModeON and BBvPowerSaveModeOFF to vnt_private and
reference __iomem there, to be removed later.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace with stucture vnt_private *priv

in functions
BBvSoftwareReset
BBvSetTxAntennaMode
BBvSetRxAntennaMode
BBvSetDeepSleep
BBvExitDeepSleep

__iomem *dwIoBase will be moved into BBbWriteEmbedded and BBbReadEmbedded
later.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

we can reach the label Away in total five situation and in four of
of them pDevInfo is NULL. so we were basically dereferencing a NULL
pointer.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

the NULL check for memregion is not required as it has already been
checked for NULL after kzalloc. so we can reach this part of the code
only if memregion is not NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add braces to the else arm of an if/else block in visorchannel_funcs.c
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rename the goto label used throughout visorchannel_funcs.c from Away to cleanup.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Split multiple logging lines to get them closer to 80 characters per line.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the || logical continuation from the start of the second line of an if statement to the end of the first line.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>