Vladimir Oltean says:

====================
Improvements to the DSA deferred xmit

After the feedback received on v1:
https://www.spinics.net/lists/netdev/msg622617.html

I've decided to move the deferred xmit implementation completely within
the sja1105 driver.

The executive summary for this series is the same as it was for v1
(better for everybody):

- For those who don't use it, thanks to one less assignment in the
  hotpath (and now also thanks to less code in the DSA core)
- For those who do, by making its scheduling more amenable and moving it
  outside the generic workqueue (since it still deals with packet
  hotpath, after all)

There are some simplification (1/3) and cosmetic (3/3) patches in the
areas next to the code touched by the main patch (2/3).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a cosmetic patch that makes the dp, tx_vid, queue_mapping and
pcp local variable definitions a bit closer in length, so they don't
look like an eyesore as much.

The 'ds' variable is not used otherwise, except for ds->dp.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 3 things that are wrong with the DSA deferred xmit mechanism:

1. Its introduction has made the DSA hotpath ever so slightly more
   inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
   to be initialized to false for every transmitted frame, in order to
   figure out whether the driver requested deferral or not (a very rare
   occasion, rare even for the only driver that does use this mechanism:
   sja1105). That was necessary to avoid kfree_skb from freeing the skb.

2. Because L2 PTP is a link-local protocol like STP, it requires
   management routes and deferred xmit with this switch. But as opposed
   to STP, the deferred work mechanism needs to schedule the packet
   rather quickly for the TX timstamp to be collected in time and sent
   to user space. But there is no provision for controlling the
   scheduling priority of this deferred xmit workqueue. Too bad this is
   a rather specific requirement for a feature that nobody else uses
   (more below).

3. Perhaps most importantly, it makes the DSA core adhere a bit too
   much to the NXP company-wide policy "Innovate Where It Doesn't
   Matter". The sja1105 is probably the only DSA switch that requires
   some frames sent from the CPU to be routed to the slave port via an
   out-of-band configuration (register write) rather than in-band (DSA
   tag). And there are indeed very good reasons to not want to do that:
   if that out-of-band register is at the other end of a slow bus such
   as SPI, then you limit that Ethernet flow's throughput to effectively
   the throughput of the SPI bus. So hardware vendors should definitely
   not be encouraged to design this way. We do _not_ want more
   widespread use of this mechanism.

Luckily we have a solution for each of the 3 issues:

For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.

For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).

For 3, we can actually move the entire implementation to the sja1105
driver.

So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I finally found out how the 4 management route slots are supposed to
be used, but.. it's not worth it.

The description from the comment I've just deleted in this commit is
still true: when more than 1 management slot is active at the same time,
the switch will match frames incoming [from the CPU port] on the lowest
numbered management slot that matches the frame's DMAC.

My issue was that one was not supposed to statically assign each port a
slot. Yes, there are 4 slots and also 4 non-CPU ports, but that is a
mere coincidence.

Instead, the switch can be used like this: every management frame gets a
slot at the right of the most recently assigned slot:

Send mgmt frame 1 through S0:    S0 x  x  x
Send mgmt frame 2 through S1:    S0 S1 x  x
Send mgmt frame 3 through S2:    S0 S1 S2 x
Send mgmt frame 4 through S3:    S0 S1 S2 S3

The difference compared to the old usage is that the transmission of
frames 1-4 doesn't need to wait until the completion of the management
route. It is safe to use a slot to the right of the most recently used
one, because by protocol nobody will program a slot to your left and
"steal" your route towards the correct egress port.

So there is a potential throughput benefit here.

But mgmt frame 5 has no more free slot to use, so it has to wait until
_all_ of S0, S1, S2, S3 are full, in order to use S0 again.

And that's actually exactly the problem: I was looking for something
that would bring more predictable transmission latency, but this is
exactly the opposite: 3 out of 4 frames would be transmitted quicker,
but the 4th would draw the short straw and have a worse worst-case
latency than before.

Useless.

Things are made even worse by PTP TX timestamping, which is something I
won't go deeply into here. Suffice to say that the fact there is a
driver-level lock on the SPI bus offsets any potential throughput gains
that parallelism might bring.

So there's no going back to the multi-slot scheme, remove the
"mgmt_slot" variable from sja1105_port and the dummy static assignment
made at probe time.

While passing by, also remove the assignment to casc_port altogether.
Don't pretend that we support cascaded setups.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
Fix 10G PHY interface types

Recent discussion has revealed that our current usage of the 10GKR
phy_interface_t is not correct. This is based on a misunderstanding
caused in part by the various specifications being difficult to
obtain. Now that a better understanding has been reached, we ought
to correct this.

This series introduce PHY_INTERFACE_MODE_10GBASER to replace the
existing usage of 10GKR mode, and document their differences in the
phylib documentation. Then switch PHY, SFP/phylink, the Marvell
PP2 network driver, and its associated comphy driver over to use
the correct interface mode. None of the existing platform usage
was actually using 10GBASE-KR.

In order to maintain compatibility with existing DT files, arrange
for the Marvell PP2 driver to rewrite the phy interface mode; this
allows other drivers to adopt correct behaviour w.r.t whether the
10G connection conforms to the backplane 10GBASE-KR protocol vs
normal 10GBASE-R protocol.

After applying these locally to net-next I've validated that the
only places which mention the old PHY_INTERFACE_MODE_10GKR
definition are:

Documentation/networking/phy.rst:``PHY_INTERFACE_MODE_10GKR``
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c:        if (phy_mode == PHY_INTERFACE_MODE_10GKR)
drivers/net/phy/aquantia_main.c:                phydev->interface = PHY_INTERFACE_MODE_10GKR;
drivers/net/phy/aquantia_main.c:            phydev->interface != PHY_INTERFACE_MODE_10GKR &&
include/linux/phy.h:    PHY_INTERFACE_MODE_10GKR,
include/linux/phy.h:    case PHY_INTERFACE_MODE_10GKR:

which is as expected.  The only users of "10gbase-kr" in DT are:

arch/arm64/boot/dts/marvell/armada-7040-db.dts: phy-mode = "10gbase-kr";
arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts:     phy-mode = "10gbase-kr";
arch/arm64/boot/dts/marvell/armada-8040-db.dts: phy-mode = "10gbase-kr";
arch/arm64/boot/dts/marvell/armada-8040-db.dts: phy-mode = "10gbase-kr";
arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts:   phy-mode = "10gbase-kr";
arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts:   phy-mode = "10gbase-kr";
arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts:      phy-mode = "10gbase-kr";arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts:      phy-mode = "10gbase-kr";arch/arm64/boot/dts/marvell/cn9130-db.dts:      phy-mode = "10gbase-kr";
arch/arm64/boot/dts/marvell/cn9131-db.dts:      phy-mode = "10gbase-kr";
arch/arm64/boot/dts/marvell/cn9132-db.dts:      phy-mode = "10gbase-kr";

which all use the mvpp2 driver, and these will be updated in a
separate patch to be submitted in the following kernel cycle.

v2: add comment to mvpp2 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.

The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.

For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent discussion has revealed that the use of PHY_INTERFACE_MODE_10GKR
is incorrect. Add a 10GBASE-R definition, document both the -R and -KR
versions, and the fact that 10GKR was used incorrectly.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: add sriov support

Set up the basic support for enabling SR-IOV devices in the
ionic driver.  Since most of the management work happens in
the NIC firmware, the driver becomes mostly a pass-through
for the network stack commands that want to control and
configure the VFs.

v4:	changed "vf too big" checks to use pci_num_vf()
	changed from vf[] array of pointers of individually allocated
	  vf structs to single allocated vfs[] array of vf structs
	added clean up of vfs[] on probe fail
	added setup for vf stats dma

v3:	added check in probe for pre-existing VFs
	split out the alloc and dealloc of vf structs to better deal
	  with pre-existing VFs (left enabled on remove)
	restored the checks for vf too big because of a potential
	  case where VFs are already enabled but driver failed to
	  alloc the vf structs

v2:	use pci_num_vf() and kcalloc()
	remove checks for vf too big
	add locking for the VF operations
	disable VFs in ionic_remove() if they are still running
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the netdev ops for managing VFs.  Since most of the
management work happens in the NIC firmware, the driver becomes
mostly a pass-through for the network stack commands that want
to control and configure the VFs.

We also tweak ionic_station_set() a little to allow for
the VFs that start off with a zero'd mac address.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds new AdminQ calls and their related structs for
supporting PF controls on VFs:
    CMD_OPCODE_VF_GETATTR
    CMD_OPCODE_VF_SETATTR
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix up inconsistent usage of upper and lowercase letters in "Samsung"
name.

"SAMSUNG" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.

Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry Torokhov says:

====================
net: phy: switch to using fwnode_gpiod_get_index

This series switches phy drivers form using fwnode_get_named_gpiod() and
gpiod_get_from_of_node() that are scheduled to be removed in favor
of fwnode_gpiod_get_index() that behaves more like standard
gpiod_get_index() and will potentially handle secondary software
nodes in cases we need to augment platform firmware.

Now that the dependencies have been merged into networking tree the
patches can be applied there as well.

v3:
        - rebased on top of net-next

v2:
        - rebased on top of Linus' W devel branch
        - added David's ACKs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

gpiod_get_from_of_node() is being retired in favor of
[devm_]fwnode_gpiod_get_index(), that behaves similar to
[devm_]gpiod_get_index(), but can work with arbitrary firmware node. It
will also be able to support secondary software nodes.

Let's switch this driver over.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we fail to locate GPIO for any reason other than deferral or
not-found-GPIO, we try to print device tree node info, however if might
be freed already as we called of_node_put() on it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of fwnode_get_named_gpiod() that I plan to hide away, let's use
the new fwnode_gpiod_get_index() that mimics gpiod_get_index(), but
works with arbitrary firmware node.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no build time dependency on CONFIG_OF, but we do need to make
sure we gate the initialization of the gpio_chip::of_node member with a
proper check on CONFIG_OF_GPIO. This enables the driver to build on
platforms that do not have CONFIG_OF enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jason A. Donenfeld says:

====================
WireGuard bug fixes and cleanups

I've been working through some personal notes and also the whole git
repo history of the out-of-tree module, looking for places where
tradeoffs were made (and subsequently forgotten about) for old kernels.
The first two patches in this series clean up those. The first one does
so in the self-tests and self-test harness, where we're now able to
expand test coverage by a bit, and we're now cooking away tests on every
commit to both the wireguard-linux repo and to net-next. The second one
removes a workaround for a skbuff.h bug that was fixed long ago.
Finally, the last patch in the series fixes in a bug unearthed by newer
Qualcomm chipsets running the rmnet_perf driver, which does UDP GRO.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Certain drivers will pass gro skbs to udp, at which point the udp driver
simply iterates through them and passes them off to encap_rcv, which is
where we pick up. At the moment, we're not attempting to coalesce these
into bundles, but we also don't want to wind up having cascaded lists of
skbs treated separately. The right behavior here, then, is to just mark
each incoming one as not on a list. This can be seen in practice, for
example, with Qualcomm's rmnet_perf driver.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Yaroslav Furman <yaro330@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before 8b700862 ("net: Don't copy pfmemalloc flag in __copy_skb_
header()"), the pfmemalloc flag used to be between headers_start and
headers_end, which is a region we clear when preparing the packet for
encryption/decryption. This is a parameter we certainly want to
preserve, which is why 8b700862 moved it out of there. The code here
was written in a world before 8b700862, though, where we had to
manually account for it. This commit brings things up to speed.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Quite a bit of the test suite was designed to work with ancient kernels.
Thankfully we no longer have to deal with this. This commit updates
things that we can finally update and removes things that we can finally
remove, to avoid the build-up of the last several years as a result of
having to support ancient kernels. We can finally rely on suppress_
prefixlength being available. On the build side of things, the no-PIE
hack is no longer required, and we can bump some of the tools, repair
our m68k and i686-kvm support, and get better coverage of the static
branches used in the crypto lib and in udp_tunnel.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2020-01-04

This series contains updates to the igc driver only.

Sasha does some housekeeping on the igc driver to remove forward
declarations that are not needed after re-arranging several functions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_sw_init function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_write_itr function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_assign_vector function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_free_q_vector function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_free_q_vectors function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_irq_disable function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_irq_enable function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_configure_msix function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_set_rx_mode function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_set_interrupt_capability function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_alloc_mapped_page function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_configure function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_set_default_mac_filter function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_power_down_link function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to avoid forward-declarations of function if possible.
Rearrange the igc_clean_tx_ring function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2020-01-03

This series contains updates to the ice driver only.

Brett adds support for UDP segmentation offload (USO) based on the work
Alex Duyck did for other Intel drivers. Refactored how the VF sets
spoof checking to resolve a couple of issues found in
ice_set_vf_spoofchk().  Adds the ability to track of the dflt_vsI
(default VSI), since we cannot have more than one default VSI.  Add a
macro for commonly used "for loop" used repeatedly in the code.  Cleaned
up and made the VF link flows all similar.  Refactor the flows of adding
and deleting MAC addresses in order to simplify the logic for error
conditions and setting/clearing the VF's default MAC address field.

Michal moves the setting of the default ITR value from ice_cfg_itr() to
the function we allocate queue vectors.  Adds support for saving and
restoring the ITR value for each queue.  Adds a check for all invalid
or unused parameters to log the information and return an error.

Vignesh cleans up the driver where we were trying to write to read-only
registers for the receive flex descriptors.

Tony changes a netdev_info() to netdev_dbg() when the MTU value is
changed.

Bruce suppresses a coverity reported error that was not really an error
by adding a code comment.

Mitch adds a check for a NULL receive descriptor to resolve a coverity
reported issue.

Krzysztof prevents a potential general protection fault by adding a
boundary check to see if the queue id is greater than the size of a UMEM
array.  Adds additional code comments to assist coverity in its scans to
prevent false positives.

Jake adds support for E822 devices to the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for E822 devices
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Coverity reports some of the calls to xdp_rxq_info_reg() as potential
issues, because the driver does not check its return value. However,
those calls are wrapped with "if (!xdp_rxq_info_is_reg(&ring->xdp_rxq))"
and this check alone is enough to be sure that the function will never
fail.

All possible states of xdp_rxq_info are:
 - NEW,
 - REGISTERED,
 - UNREGISTERED,
 - UNUSED.

The driver won't mark a queue as UNUSED under no circumstance, so the
return value can be ignored safely.

Add comments for Coverity right above calls to xdp_rxq_info_reg() to
suppress the warnings.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In ice_xsk_umem(), variable qid which is later used as an array index,
is not validated for a possible boundary exceedance. Because of that,
a calling function might receive an invalid address, which causes
general protection fault when dereferenced.

To address this, add a boundary check to see if qid is greater than the
size of a UMEM array. Also, don't let user change vsi->num_xsk_umems
just by trying to setup a second UMEM if its value is already set up
(i.e. UMEM region has already been allocated for this VSI).

While at it, make sure that ring->zca.free pointer is always zeroed out
if there is no UMEM on a specified ring.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>