Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len
for physical address and length of framebuffer.

This also fixes output of the 'fbset -i' command - address and length
of the framebuffer is displayed correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len
for physical address and length of framebuffer.

This also fixes output of the 'fbset -i' command - address and length
of the framebuffer is displayed correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

irq_choose_cpu() should compare the affinity mask against cpu_online_map
rather than CPU_MASK_ALL, since irq_select_affinity() sets the interrupt's
affinity mask to cpu_online_map "and" CPU_MASK_ALL (which ends up being
just cpu_online_map).  The mask comparison in irq_choose_cpu() will always
fail since the two masks are not the same.  So the CPU chosen is the first CPU
in the intersection of cpu_online_map and CPU_MASK_ALL, which is always CPU0.
That means all interrupts are reassigned to CPU0...

Distributing interrupts to CPUs in a linearly increasing round robin fashion
is not optimal for the UltraSPARC T1/T2.  Also, the irq_rover in
irq_choose_cpu() causes an interrupt to be assigned to a different
processor each time the interrupt is allocated and released.  This may lead
to an unbalanced distribution over time.

A static mapping of interrupts to processors is done to optimize and balance
interrupt distribution.  For the T1/T2, interrupts are spread to different
cores first, and then to strands within a core.

The following is some benchmarks showing the effects of interrupt
distribution on a T2.  The test was done with iperf using a pair of T5220
boxes, each with a 10GBe NIU (XAUI) connected back to back.

  TCP     | Stock       Linear RR IRQ  Optimized IRQ
  Streams | 2.6.30-rc5  Distribution   Distribution
          | GBits/sec   GBits/sec      GBits/sec
  --------+-----------------------------------------
    1       0.839       0.862          0.868
    8       1.16        4.96           5.88
   16       1.15        6.40           8.04
  100       1.09        7.28           8.68
Signed-off-by: Hong H. Pham <hong.pham@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

This gets us real close to the generic implementation of
setup_per_cpu_areas() except:

1) We store the per-cpu offset into the trap_block[], whereas
   the generic code has it's own static array.

2) We have to initialize the %g5 register to hold the boot cpu's
   per-cpu area offset.

3) The OBP/MDESC cpu info scan is performed at the end.
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we defer the cpu_data() initializations to the end of per-cpu
setup, we can get rid of this local hack we had to setup the per-cpu
areas eary.

This is a necessary step in order to support HAVE_DYNAMIC_PER_CPU_AREA
since the per-cpu setup must run when page structs are available.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

We need to split up the cpu present mask setup from the cpu_data
initialization, and this is a first step towards that.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

With feedback from Sam Ravnborg.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Surprisingly this actually makes LOAD_PER_CPU_BASE() a little
more efficient.
Signed-off-by: David S. Miller <davem@davemloft.net>

Later we're going to want to get at these definitions from
asm/percpu.h and that's not possible via cpudata.h because
of the set of dependencies the non-trap_block[] stuff has.
Signed-off-by: David S. Miller <davem@davemloft.net>

This really isn't necessary at all, a local variable suits the
job just fine.

This frees up 8 bytes in the trap_block[] that we can use later
to store the per-cpu base addresses.
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] fix compile error in arch/ia64/mm/extable.c

Merge branch 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  timers: Logic to move non pinned timers
  timers: /proc/sys sysctl hook to enable timer migration
  timers: Identifying the existing pinned timers
  timers: Framework for identifying pinned timers
  timers: allow deferrable timers for intervals tv2-tv5 to be deferred

Fix up conflicts in kernel/sched.c and kernel/timer.c manually

Merge branch 'timers-for-linus-clockevents' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-clockevents' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clockevent: export register_device and delta2ns
  clockevents: tick_broadcast_device can become static

Merge branch 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clocksource: prevent selection of low resolution clocksourse also for nohz=on
  clocksource: sanity check sysfs clocksource changes

Merge branch 'timers-for-linus-ntp' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-ntp' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  ntp: fix comment typos
  ntp: adjust SHIFT_PLL to improve NTP convergence

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1244 commits)
  pkt_sched: Rename PSCHED_US2NS and PSCHED_NS2US
  ipv4: Fix fib_trie rebalancing
  Bluetooth: Fix issue with uninitialized nsh.type in DTL-1 driver
  Bluetooth: Fix Kconfig issue with RFKILL integration
  PIM-SM: namespace changes
  ipv4: update ARPD help text
  net: use a deferred timer in rt_check_expire
  ieee802154: fix kconfig bool/tristate muckup
  bonding: initialization rework
  bonding: use is_zero_ether_addr
  bonding: network device names are case sensative
  bonding: elminate bad refcount code
  bonding: fix style issues
  bonding: fix destructor
  bonding: remove bonding read/write semaphore
  bonding: initialize before registration
  bonding: bond_create always called with default parameters
  x_tables: Convert printk to pr_err
  netfilter: conntrack: optional reliable conntrack event delivery
  list_nulls: add hlist_nulls_add_head and hlist_nulls_del
  ...

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
  powerpc: Fix bug in move of altivec code to vector.S
  powerpc: Add support for swiotlb on 32-bit
  powerpc/spufs: Remove unused error path
  powerpc: Fix warning when printing a resource_size_t
  powerpc/xmon: Remove unused variable in xmon.c
  powerpc/pseries: Fix warnings when printing resource_size_t
  powerpc: Shield code specific to 64-bit server processors
  powerpc: Separate PACA fields for server CPUs
  powerpc: Split exception handling out of head_64.S
  powerpc: Introduce CONFIG_PPC_BOOK3S
  powerpc: Move VMX and VSX asm code to vector.S
  powerpc: Set init_bootmem_done on NUMA platforms as well
  powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
  powerpc/mm: Fix some SMP issues with MMU context handling
  powerpc: Add PTRACE_SINGLEBLOCK support
  fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
  powerpc/virtex: Add ml510 reference design device tree
  powerpc/virtex: Add Xilinx ML510 reference design support
  powerpc/virtex: refactor intc driver and add support for i8259 cascading
  powerpc/virtex: Add support for Xilinx PCI host bridge
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator/max1586: fix V3 gain calculation integer overflow
  regulator/max1586: support increased V3 voltage range
  regulator: lp3971 - fix driver link error when built-in.
  LP3971 PMIC regulator driver (updated and combined version)
  regulator: remove driver_data direct access of struct device
  regulator: Set MODULE_ALIAS for regulator drivers
  regulator: Support list_voltage for fixed voltage regulator
  regulator: Move regulator drivers to subsys_initcall()
  regulator: build fix for powerpc - renamed show_state
  regulator: add userspace-consumer driver
  Maxim 1586 regulator driver

ad6561df ("module: trim exception table on init
free.") put a bogus trim_init_extable() function into ia64 which didn't compile.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (22 commits)
  nilfs2: support contiguous lookup of blocks
  nilfs2: add sync_page method to page caches of meta data
  nilfs2: use device's backing_dev_info for btree node caches
  nilfs2: return EBUSY against delete request on snapshot
  nilfs2: modify list of unsupported features in caveats
  nilfs2: enable sync_page method
  nilfs2: set bio unplug flag for the last bio in segment
  nilfs2: allow future expansion of metadata read out via get info ioctl
  NILFS2: Pagecache usage optimization on NILFS2
  nilfs2: remove nilfs_btree_operations from btree mapping
  nilfs2: remove nilfs_direct_operations from direct mapping
  nilfs2: remove bmap pointer operations
  nilfs2: remove useless b_low and b_high fields from nilfs_bmap struct
  nilfs2: remove pointless NULL check of bpop_commit_alloc_ptr function
  nilfs2: move get block functions in bmap.c into btree codes
  nilfs2: remove nilfs_bmap_delete_block
  nilfs2: remove nilfs_bmap_put_block
  nilfs2: remove header file for segment list operations
  nilfs2: eliminate removal list of segments
  nilfs2: add sufile function that can modify multiple segment usages
  ...

On Thu, May 28, 2009 at 10:59 AM, Mark Brown <broonie@opensource.wolfsonmicro.com> wrote:
> On Thu, May 28, 2009 at 07:15:16AM +0200, Philipp Zabel wrote:
>> The V3 regulator can be configured with an external resistor
>> connected to the feedback pin (R24 in the data sheet) to
>> increase the voltage range.
>>
>> For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
>> V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
>>
>> Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
>
> Looks good.
>
> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Thanks, but it turns out I hit a 32 bit integer overflow in
the gain calculation. I'd like to mend that with the following
patch. Now max_uV could be increased up to 4.294 V, enough to
charge LiPo cells.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The V3 regulator can be configured with an external resistor
connected to the feedback pin (R24 in the data sheet) to
increase the voltage range.

For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

lp3971_i2c_remove' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.devexit.text' of drivers/built-in.o
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Several of the regulator drivers didn't have MODULE_ALIAS so couldn't be
auto loaded. Add the MODULE_ALIAS in case they do get built as modules.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Regulators need to be available early in init in order to allow them
to be available for consumers when requested. This is generally done
by registering them at subsys_initcall() time but not all regulator
drivers have done that. Convert these drivers to do so in order to
mimimise future support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch fixes the follwing build failure on powerpc:-

> Today's linux-next build (powerpc allyesconfig) failed like this:
>
> drivers/regulator/userspace-consumer.c:43: error: conflicting types
> for 'show_state'
> include/linux/sched.h:273: note: previous definition of 'show_state'
> was here
>
> Caused by commit 5defa2bce704ca4151cfe24e4297aa7797cafd22 ("regulator:
> add userspace-consumer driver") which I have reverted for today.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The userspace-consumer driver allows control of voltage and current
regulator state from userspace. This is required for fine-grained
power management of devices that are completely controller by userspace
applications, e.g. a GPS transciever connected to a serial port.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.

The chip is controlled through the I2C bus.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/scsi/fcoe/fcoe.c
	net/core/drop_monitor.c
	net/core/net-traces.c

Let's use TICKS instead of US, so PSCHED_TICKS2NS and PSCHED_NS2TICKS
(like in PSCHED_TICKS_PER_SEC already) to avoid misleading.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While doing trie_rebalance(): resize(), inflate(), halve() RCU free
tnodes before updating their parents. It depends on RCU delaying the
real destruction, but if RCU readers start after call_rcu() and before
parent update they could access freed memory.

It is currently prevented with preempt_disable() on the update side,
but it's not safe, except maybe classic RCU, plus it conflicts with
memory allocations with GFP_KERNEL flag used from these functions.

This patch explicitly delays freeing of tnodes by adding them to the
list, which is flushed after the update is finished.
Reported-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On systems where CONFIG_SHMEM is disabled, mounting tmpfs filesystems can
fail when tmpfs options are used.  This is because tmpfs creates a small
wrapper around ramfs which rejects unknown options, and ramfs itself only
supports a tiny subset of what tmpfs supports.  This makes it pretty hard
to use the same userspace systems across different configuration systems.
As such, ramfs should ignore the tmpfs options when tmpfs is merely a
wrapper around ramfs.

This used to work before commit c3b1b1cb as previously, ramfs would
ignore all options.  But now, we get:
ramfs: bad mount option: size=10M
mount: mounting mdev on /dev failed: Invalid argument

Another option might be to restore the previous behavior, where ramfs
simply ignored all unknown mount options ... which is what Hugh prefers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: Matt Mackall <mpm@selenic.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>