The driver is getting hit with 100s of RSCNs during remote port address
changes. Each of those RSCN's ends up generating UNREG_RPI and REG_PRI
mailbox commands.  The discovery engine within the driver doesn't wait for
the mailbox command completions. Instead it sets state flags and moves
forward. At some point, there's a massive backlog of mailbox commands which
take time for the adapter to process. Additionally, it appears there were
duplicate events from the switch so the driver generated duplicate mailbox
commands for the same remote port.  During this window, failures on PLOGI
and PRLI ELS's are see as the adapter is rejecting them as they are for
remote ports that still have pending mailbox commands.

Streamline the discovery engine so that PLOGI log checks for outstanding
UNREG_RPIs and defer the processing until the commands complete. This
better synchronizes the ELS transmission vs the RPI registrations.

Filter out multiple UNREG_RPIs being queued up for the same remote port.

Beef up log messages in this area.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code.  Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.

Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Update manufacturer attribute to reflect Broadcom Inc, not Emulex
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

While trying to get adapter fw-log for a function whose buffsize was set to
0, kernel panic occurred.

When buffsize is 0, the kernel buffer for the log won't be allocated.  When
fw log usage was enabled, it failed to check the buffer size, and log usage
was started. Eventually the driver referenced the unallocated log buffer.

Added checks of the buffer size before allowing fw logging to be enabled
and added check for valid buffer if enabling fw log.

Performed a couple other minor cleanups while fixing this:
 - clarified log messages
 - re-evaluated log message severity
 - treat any error as an error, not only a couple codes
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

dma_addr_t can be u64 on pae systems but isa_virt_to_bus only ever
returns unsigned long (because an ISA physical address can only be 24
bits). Cast to unsigned long to avoid division.

Fixes: 1794ef2b ("scsi: aha1542: convert to DMA mapping API")
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Complements

v2.6.35 commit 64deb6ef ("[SCSI] zfcp: Use status_read_buf_num
provided by FCP channel") which replaced the hardcoded 16 with a
variable value

Also complements already existing fixups for above commit

v2.6.35 commit 8d88cf3f ("[SCSI] zfcp: Update status read mempool")
v3.10   commit 9edf7d75 ("[SCSI] zfcp: status read buffers on first adapter open with link down")
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Suppose adapter (open) recovery is between opened QDIO queues and before
(the end of) initial posting of status read buffers (SRBs). This time
window can be seconds long due to FSF_PROT_HOST_CONNECTION_INITIALIZING
causing by design looping with exponential increase sleeps in the function
performing exchange config data during recovery
[zfcp_erp_adapter_strat_fsf_xconf()]. Recovery triggered by local link up.

Suppose an event occurs for which the FCP channel would send an unsolicited
notification to zfcp by means of a previously posted SRB.  We saw it with
local cable pull (link down) in multi-initiator zoning with multiple
NPIV-enabled subchannels of the same shared FCP channel.

As soon as zfcp_erp_adapter_strategy_open_fsf() starts posting the initial
status read buffers from within the adapter's ERP thread, the channel does
send an unsolicited notification.

Since v2.6.27 commit d26ab06e ("[SCSI] zfcp: receiving an unsolicted
status can lead to I/O stall"), zfcp_fsf_status_read_handler() schedules
adapter->stat_work to re-fill the just consumed SRB from a work item.

Now the ERP thread and the work item post SRBs in parallel.  Both contexts
call the helper function zfcp_status_read_refill().  The tracking of
missing (to be posted / re-filled) SRBs is not thread-safe due to separate
atomic_read() and atomic_dec(), in order to depend on posting
success. Hence, both contexts can see
atomic_read(&adapter->stat_miss) == 1. One of the two contexts posts
one too many SRB. Zfcp gets QDIO_ERROR_SLSB_STATE on the output queue
(trace tag "qdireq1") leading to zfcp_erp_adapter_shutdown() in
zfcp_qdio_handler_error().

An obvious and seemingly clean fix would be to schedule stat_work from the
ERP thread and wait for it to finish. This would serialize all SRB
re-fills. However, we already have another work item wait on the ERP
thread: adapter->scan_work runs zfcp_fc_scan_ports() which calls
zfcp_fc_eval_gpn_ft(). The latter calls zfcp_erp_wait() to wait for all the
open port recoveries during zfcp auto port scan, but in fact it waits for
any pending recovery including an adapter recovery. This approach leads to
a deadlock.  [see also v3.19 commit 18f87a67 ("zfcp: auto port scan
resiliency"); v2.6.37 commit d3e1088d
("[SCSI] zfcp: No ERP escalation on gpn_ft eval");
v2.6.28 commit fca55b6f
("[SCSI] zfcp: fix deadlock between wq triggered port scan and ERP")
fixing v2.6.27 commit c57a39a4
("[SCSI] zfcp: wait until adapter is finished with ERP during auto-port");
v2.6.27 commit cc8c2829
("[SCSI] zfcp: Automatically attach remote ports")]

Instead make the accounting of missing SRBs atomic for parallel execution
in both the ERP thread and adapter->stat_work.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: d26ab06e ("[SCSI] zfcp: receiving an unsolicted status can lead to I/O stall")
Cc: <stable@vger.kernel.org> #2.6.27+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.

Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Initialise the t10_wwn vendor, model and revision defaults when a device is
allocated instead of when it's enabled. This ensures that custom vendor or
model strings set prior to enablement are not later overwritten with
default values.

The TRANSPORT_FLAG_PASSTHROUGH conditional can be dropped for the following
reasons:

 - target_core_pscsi overwrites the defaults in the
   pscsi_configure_device() callback.
   + the contents is then only used for ConfigFS via
     $pscsi_dev/statistics/scsi_lu/vend, etc.

 - target_core_user doesn't touch the defaults, nor are they used for
   anything outside of ConfigFS.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Use the value stored in t10_wwn.vendor, which defaults to "LIO-ORG", but
can be reconfigured via the vendor_id ConfigFS attribute.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Bryant G. Ly <bly@catalogicsoftware.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The vendor_id attribute will allow for the modification of the T10 Vendor
Identification string returned in inquiry responses. Its value can be
viewed and modified via the ConfigFS path at:

target/core/$backstore/$name/wwn/vendor_id

"LIO-ORG" remains the default value, which is set when the backstore device
is enabled.

[mkp: corrected VPD page number]
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In preparation for supporting user provided vendor strings, add an extra
byte to the vendor, model and revision arrays in struct t10_wwn. This
ensures that the full INQUIRY data can be carried in the arrays along with
a null-terminator.

Change a number of array readers and writers so that they account for
explicit null-termination:

- The pscsi_set_inquiry_info() and emulate_model_alias_store() codepaths
  don't currently explicitly null-terminate; fix this.

- Existing t10_wwn field dumps use for-loops which step over
  null-terminators for right-padding.
  + Use printf with width specifiers instead.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

spc5r17.pdf specifies:

  4.3.1 ASCII data field requirements
  ASCII data fields shall contain only ASCII printable characters (i.e.,
  code values 20h to 7Eh) and may be terminated with one or more ASCII null
  (00h) characters.  ASCII data fields described as being left-aligned
  shall have any unused bytes at the end of the field (i.e., highest
  offset) and the unused bytes shall be filled with ASCII space characters
  (20h).

LIO currently space-pads the T10 VENDOR IDENTIFICATION and PRODUCT
IDENTIFICATION fields in the standard INQUIRY data. However, the PRODUCT
REVISION LEVEL field in the standard INQUIRY data as well as the T10 VENDOR
IDENTIFICATION field in the INQUIRY Device Identification VPD Page are
zero-terminated/zero-padded.

Fix this inconsistency by using space-padding for all of the above fields.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bryant G. Ly <bly@catalogicsoftware.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

NULL check before some freeing functions is not needed.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

NULL check before some freeing functions is not needed.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

NULL check before some freeing functions is not needed.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Nesting in __qla2x00_abort_all_cmds() is way too deep. Reduce the nesting
level by introducing a helper function. This patch does not change any
functionality.
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

flush_scheduled_work() is not required as csio_hw_exit_workers() calls
cancel_work_sync() for hw->evtq_work.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Introduce separate zfcp module parameters to individually select support
for: DIF which should work (zfcp.dif, which used to be DIF+DIX, disabled)
or DIX+DIF which can cause trouble (zfcp.dix, new, disabled).

If DIX is enabled, we warn on zfcp driver initialization.  As before, this
also reduces the maximum I/O request size to half, to support the worst
case of merged single sector requests with one protection data scatter
gather element per sector. This can impact the maximum throughput.

In DIF-only mode (zfcp.dif=1 zfcp.dix=0), we can use the full maximum I/O
request size as there is no protection data for zfcp.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Fedor Loshakov <loshakov@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1056537 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

By spec, the ufs sense data is 18 bytes long.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Replaced vmalloc + memset with vzalloc
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Replaced vmalloc + memset with vzalloc
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Due to the "make ABORT and LUN RESET handling synchronous" patch, cmd->work
is only modified from the regular command execution path and no longer
asynchronously by the code that executes task management functions. Since
the regular command execution code is sequential per command, no locking is
required to manipulate cmd->work. Hence stop protecting cmd->work
manipulations with locking.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Instead of invoking target driver callback functions from the context that
handles an abort or LUN RESET task management function, only set the abort
flag from that context and perform the actual abort handling from the
context of the regular command processing flow. This approach has the
advantage that the task management code becomes much easier to read and to
verify since the number of potential race conditions against the command
processing flow is strongly reduced.

This patch has been tested by running the following two shell commands
concurrently for about ten minutes for both the iSCSI and the SRP target
drivers ($dev is an initiator device node connected with storage provided
by the target driver under test):

 * fio with data verification enabled on a filesystem mounted on top of
   $dev.

 * while true; do sg_reset -d $dev; echo -n .; sleep .1; done

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The TASK ABORTED STATUS (TAS) bit is defined as follows in SAM:
"TASK_ABORTED: this status shall be returned if a command is aborted by a
command or task management function on another I_T nexus and the control
mode page TAS bit is set to one". TAS handling is spread over the target
core and the iSCSI target driver. If a LUN RESET is received, the target
core will send the TASK_ABORTED response for all commands for which such a
response has to be sent. If an ABORT TASK is received, only the iSCSI
target driver will send the TASK_ABORTED response for the commands for
which that response has to be sent.  That is a bug since all target drivers
have to honor the TAS bit. Fix this by moving the code that handles TAS
from the iSCSI target driver into the target core. Additionally, if a
command has been aborted, instead of sending the TASK_ABORTED status from
the context that processes the SCSI command send it from the context of the
ABORT TMF.  The core_tmr_abort_task() change in this patch causes the
CMD_T_TAS flag to be set if a TASK_ABORTED status has to be sent back to
the initiator that submitted the command. If that flag has been set
transport_cmd_finish_abort() will send the TASK_ABORTED response.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Instead of allowing the code that aborts a SCSI command to finish before
all iSCSI data frames have been received, make that code wait until all
iSCSI data frames have been received. Introduce a new member variable in
the target driver template to communicate that information from the iSCSI
target driver to the target core. This change allows to leave out the check
whether or not it is already safe to send the TASK_ABORTED reply from
transport_send_task_abort().

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch does not change any functionality but makes the patch that makes
TMF handling synchronous easier to read.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

A quote from SAM-5: "The order in which task management requests are
processed is not specified by the SCSI architecture model.  The SCSI
architecture model does not require in-order delivery of such task
management requests or processing by the task manager in the order
received. To guarantee the processing order of task management requests
referencing sent to a specific logical unit, an application client should
not have more than one such task management request pending to that logical
unit." This means that it is safe to use the system workqueues instead of
tmr_wq for processing TMFs. An intended side effect of this patch is that
it enables concurrent processing of TMFs.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

A session must only be released after all code that accesses the session
structure has finished. Make sure that this is the case by introducing a
new command counter per session that is only decremented after the
.release_cmd() callback has finished. This patch fixes the following crash:

BUG: KASAN: use-after-free in do_raw_spin_lock+0x1c/0x130
Read of size 4 at addr ffff8801534b16e4 by task rmdir/14805
CPU: 16 PID: 14805 Comm: rmdir Not tainted 4.18.0-rc2-dbg+ #5
Call Trace:
dump_stack+0xa4/0xf5
print_address_description+0x6f/0x270
kasan_report+0x241/0x360
__asan_load4+0x78/0x80
do_raw_spin_lock+0x1c/0x130
_raw_spin_lock_irqsave+0x52/0x60
srpt_set_ch_state+0x27/0x70 [ib_srpt]
srpt_disconnect_ch+0x1b/0xc0 [ib_srpt]
srpt_close_session+0xa8/0x260 [ib_srpt]
target_shutdown_sessions+0x170/0x180 [target_core_mod]
core_tpg_del_initiator_node_acl+0xf3/0x200 [target_core_mod]
target_fabric_nacl_base_release+0x25/0x30 [target_core_mod]
config_item_release+0x9c/0x110 [configfs]
config_item_put+0x26/0x30 [configfs]
configfs_rmdir+0x3b8/0x510 [configfs]
vfs_rmdir+0xb3/0x1e0
do_rmdir+0x262/0x2c0
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Since transport_clear_lun_ref() already waits until the percpu-refcount
.release() method is called, it is not necessary to wait first until
percpu_ref_kill_and_confirm() has finished transitioning the refcount into
atomic mode. Remove the code that waits for percpu_ref_kill_and_confirm()
to complete and also the completion object that is used by that code.  This
patch does not change the behavior of the SCSI target code.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch does not change any functionality. Note: the code that frees
sess_cmd_map already uses kvfree() so that code does not need to be
modified.
Reviewed-by: David Disseldorp <ddiss@suse.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch does not change any functionality but avoids that sparse
complains about the queue_cmd_ring() function and its callers.

Fixes: 6fd0ce79 ("tcmu: prep queue_cmd_ring to be used by unmap wq")
Reviewed-by: David Disseldorp <ddiss@suse.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Notice that, in this particular case, I replaced "Missed the backend's
Closing state -- fallthrough" with "fall through - Missed the backend's
Closing state", which contains the "fall through" annotation at the
beginnig of the code comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Notice that, in this particular case, I replaced "Fall thru" with a "Fall
through" annotation and added a dash as a token in order to separate the
"Fall through" annotation from the rest of the comment on the same line,
which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Addresses-Coverity-ID: 1195463 ("Missing break in switch")
Addresses-Coverity-ID: 1195464 ("Missing break in switch")
Addresses-Coverity-ID: 1195465 ("Missing break in switch")
Addresses-Coverity-ID: 1195466 ("Missing break in switch")
Addresses-Coverity-ID: 1357338 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Also, a break statement is properly aligned.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>