This reverts commit a81cf979.

The patch causes a regression, which I cannot find the reason for.
So let's revert for now, as a revert hurts only performance.

Original report:
I was trying to resolve the problem with Oliver but we don't get any conclusion
for 5 months, so I am now sending this to mail list and cdc_acm authors.

I am using simple request-response protocol to obtain the boiller parameters
in constant intervals.

A simple one transaction is:
1. opening the /dev/ttyACM0
2. sending the following 10-bytes request to the device:
   unsigned char req[] = {0x02, 0xfe, 0x01, 0x05, 0x08, 0x02, 0x01, 0x69, 0xab, 0x03};
3. reading response (frame of 74 bytes length).
4. closing the descriptor
I am doing this transaction with 5 seconds intervals.

Before the bad commit everything was working correctly: I've got a requests and
a responses in a timely manner.

After the bad commit more time I am using the kernel module, more problems I have.
The graph [2] is showing the problem.

As you can see after module load all seems fine but after about 30 minutes I've got
a plenty of EAGAINs when doing read()'s and trying to read back the data.

When I rmmod and insmod the cdc_acm module again, then the situation is starting
over again: running ok shortly after load, and more time it is running, more EAGAINs
I have when calling read().

As a bonus I can see the problem on the device itself:
The device is configured as you can see here on this screen [3].
It has two transmision LEDs: TX and RX. Blink duration is set for 100ms.
This is a recording before the bad commit when all is working fine: [4]
And this is with the bad commit: [5]
As you can see the TX led is blinking wrongly long (indicating transmission?)
and I have problems doing read() calls (EAGAIN).
Reported-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: a81cf979 ("cdc-acm: implement put_char() and flush_chars()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since renesas_usb3 udc driver calls usb_of_get_companion_dev()
which is on usb/core/of.c, build error like below happens if we
disable CONFIG_USB because the usb/core/ needs CONFIG_USB:

ERROR: "usb_of_get_companion_dev" [drivers/usb/gadget/udc/renesas_usb3.ko] undefined!

According to the usb/gadget/Kconfig, "NOTE:  Gadget support
** DOES NOT ** depend on host-side CONFIG_USB !!".
So, to fix the issue, this patch changes the usb_of_get_companion_dev()
place from usb/core/of.c to usb/common/common.c to be called by both
host and gadget.
Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39facfa0 ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The MTK xHCI controller use some reserved bytes in endpoint context for
bandwidth scheduling, so need keep them in xhci_endpoint_copy();

The issue is introduced by:
commit f5249461 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
It resets endpoints and will drop bandwidth scheduling parameters used
by interrupt or isochronous endpoints on MTK xHCI controller.
Fixes: f5249461 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")

Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.19-rc2

NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.

DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.

DWC3 got a fix for ULPI clock configuration on Baytrail devices.

FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.

Merge tag 'usb-serial-4.19-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v4.19-rc3

Here are two fixes for array-underflow bugs in completion handlers due
to insufficient sanity checks.

All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>

wdm_in_callback() is a completion handler function for the USB driver.
So it should not sleep. But it calls service_outstanding_interrupt(),
which calls usb_submit_urb() with GFP_KERNEL.

To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.

This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

async_complete() in uss720.c is a completion handler function for the
USB driver. So it should not sleep, but it is can sleep according to the
function call paths (from bottom to top) in Linux-4.16.

[FUNC] set_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 372:
  set_1284_register in parport_uss720_frob_control
drivers/parport/ieee1284.c, 560:
  [FUNC_PTR]parport_uss720_frob_control in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
  parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
  parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
  parport_generic_irq in async_complete

[FUNC] get_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 382:
  get_1284_register in parport_uss720_read_status
drivers/parport/ieee1284.c, 555:
  [FUNC_PTR]parport_uss720_read_status in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
  parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
  parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
  parport_generic_irq in async_complete

Note that [FUNC_PTR] means a function pointer call is used.

To fix these bugs, GFP_KERNEL is replaced with GFP_ATOMIC.

These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function
for the USB driver. So it should not sleep, but it is can sleep
according to the function call paths (from bottom to top) in Linux-4.16.

[FUNC] msleep
drivers/usb/host/u132-hcd.c, 2558:
	msleep in u132_get_frame
drivers/usb/core/hcd.c, 2231:
	[FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number
drivers/usb/core/usb.c, 822:
	usb_hcd_get_frame_number in usb_get_current_frame_number
sound/usb/usx2y/usbusx2yaudio.c, 303:
	usb_get_current_frame_number in i_usX2Y_urb_complete
sound/usb/usx2y/usbusx2yaudio.c, 366:
	i_usX2Y_urb_complete in i_usX2Y_subs_startup

Note that [FUNC_PTR] means a function pointer call is used.

To fix this bug, msleep() is replaced with mdelay().

This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The steps taken by usb core to set a new interface is very different from
what is done on the xHC host side.

xHC hardware will do everything in one go. One command is used to set up
new endpoints, free old endpoints, check bandwidth, and run the new
endpoints.

All this is done by xHC when usb core asks the hcd to check for
available bandwidth. At this point usb core has not yet flushed the old
endpoints, which will cause use-after-free issues in xhci driver as
queued URBs are cancelled on a re-allocated endpoint.

To resolve this add a call to usb_disable_interface() which will flush
the endpoints before calling usb_hcd_alloc_bandwidth()

Additional checks in xhci driver will also be implemented to gracefully
handle stale URB cancel on freed and re-allocated endpoints

Cc: <stable@vger.kernel.org>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix kernel-doc warning for missing struct member description:

../include/linux/mod_devicetable.h:763: warning: Function parameter or member 'driver_data' not described in 'typec_device_id'

Fixes: 8a37d87d ("usb: typec: Bus type for alternate modes")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix kernel-doc warning for missing function parameter 'mode' description:

../drivers/usb/typec/bus.c:268: warning: Function parameter or member 'mode' not described in 'typec_match_altmode'

Also fix typos for same function documentation.

Fixes: 8a37d87d ("usb: typec: Bus type for alternate modes")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_hc_died() should only be called once, and with the primary HCD
as parameter. It will mark both primary and secondary hcd's dead.

Remove the extra call to usb_cd_died with the shared hcd as parameter.

Fixes: ff9d78b3 ("USB: Set usb_hcd->state and flags for shared roothubs")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If dual role mode is enabled, when switch u3port0 to device mode,
it will affect port id calculation of host(xHCI), specially when
host supports multi U2 ports or U3 ports, so need enable its dual
role mode, and fix it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The hope that UAS devices would be less broken than old style storage
devices has turned out to be unfounded. Make UAS support more of the
quirk flags of the old driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This device does not correctly handle the LPM operations.

Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.

This patch adds the equivalent quirk logic as found in uas.
Signed-off-by: Tim Anderson <tsa@biglakesoftware.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix kernel-doc warning (13 times):

../drivers/usb/typec/class.c:1497: warning: Excess function parameter 'drvdata' description in 'typec_port_register_altmode'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix kernel-doc warning:

../drivers/usb/dwc3/gadget.c:510: warning: Excess function parameter 'dwc' description in 'dwc3_gadget_start_config'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

snprintf() always returns the full length of the string it could have
printed, even if it was truncated because the buffer was too small.
So in case the counter value is truncated, we will over-read from
in_buffer and over-write to the caller's buffer.

I don't think it's actually possible for this to happen, but in case
truncation occurs, WARN and return -EIO.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the written data starts with a digit, yurex_write() tries to parse
it as an integer using simple_strtoull().  This requires a null-
terminator, and currently there's no guarantee that there is one.

(The sample program at
https://github.com/NeoCat/YUREX-driver-for-Linux/blob/master/sample/yurex_clock.pl
writes an integer without a null terminator.  It seems like it must
have worked by chance!)

Always add a null byte after the written data.  Enlarge the buffer
to allow for this.

Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In xhci_plat_probe() both sysdev and pdev->dev are being used
for finding quirks. There are some drivers(like dwc3 host.c)
which adds quirks(like usb3-lpm-capable) into pdev and the logic
present in xhci_plat_probe() checks for quirks in either sysdev
or pdev for finding the quirks. Because of this logic, some of
the quirks are getting missed(usb3-lpm-capable quirk added by dwc3
host.c driver is getting missed).This patch fixes this by iterating
over all the available parents for finding the quirks. In this way
all the quirks which are present in child or parent are correctly
updated.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure the cancelled URB is on the current endpoint ring.

If the endpoint ring has been reallocated since the URB was enqueued
then the URB may contain TD and TRB pointers to a already freed ring.
In this the case return the URB without touching any of the freed ring
structure data.

Don't try to stop the ring. It would be useless.

This can occur if endpoint is not flushed before it is dropped and
re-added, which is the case in usb_set_interface() as xhci does
things in an odd order.

Cc: <stable@vger.kernel.org>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

WORLDE Controller KS49 or Prodipe MIDI 49C USB controller
cause a -EPROTO error, a communication restart and loop again.

This issue has already been fixed for KS25.
https://lore.kernel.org/patchwork/patch/753077/

I just add device 201 for KS49 in quirks.c to get it works.
Signed-off-by: Laurent Roux <xpros64@hotmail.fr>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:

[    1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[    1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[    1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[    2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[    2.015176] dwc2: probe of 50000000.usb failed with error -16

The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull devicetree updates from Rob Herring:
 "A couple of new helper functions in preparation for some tree wide
  clean-ups.

  I'm sending these new helpers now for rc2 in order to simplify the
  dependencies on subsequent cleanups across the tree in 4.20"

* tag 'devicetree-fixes-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: Add device_type access helper functions
  of: add node name compare helper functions
  of: add helper to lookup compatible child node

Pull ARM SoC fixes from Olof Johansson:
 "First batch of fixes post-merge window:

   - A handful of devicetree changes for i.MX2{3,8} to change over to
     new panel bindings. The platforms were moved from legacy
     framebuffers to DRM and some development board panels hadn't yet
     been converted.

   - OMAP fixes related to ti-sysc driver conversion fallout, fixing
     some register offsets, no_console_suspend fixes, etc.

   - Droid4 changes to fix flaky eMMC probing and vibrator DTS mismerge.

   - Fixed 0755->0644 permissions on a newly added file.

   - Defconfig changes to make ARM Versatile more useful with QEMU
     (helps testing).

   - Enable defconfig options for new TI SoC platform that was merged
     this window (AM6)"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: defconfig: Enable TI's AM6 SoC platform
  ARM: defconfig: Update the ARM Versatile defconfig
  ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
  ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
  ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
  ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
  ARM: dts: imx23-evk: Convert to the new display bindings
  ARM: dts: imx23-evk: Move regulators outside simple-bus
  ARM: dts: imx28-evk: Convert to the new display bindings
  ARM: dts: imx28-evk: Move regulators outside simple-bus
  Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
  arm: dts: am4372: setup rtc as system-power-controller
  ARM: dts: omap4-droid4: fix vibrations on Droid 4
  bus: ti-sysc: Fix no_console_suspend handling
  bus: ti-sysc: Fix module register ioremap for larger offsets
  ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
  ARM: OMAP2+: Fix null hwmod for ti-sysc debug

Pull x86 fixes from Thomas Gleixner:
 "Speculation:

   - Make the microcode check more robust

   - Make the L1TF memory limit depend on the internal cache physical
     address space and not on the CPUID advertised physical address
     space, which might be significantly smaller. This avoids disabling
     L1TF on machines which utilize the full physical address space.

   - Fix the GDT mapping for EFI calls on 32bit PTI

   - Fix the MCE nospec implementation to prevent #GP

  Fixes and robustness:

   - Use the proper operand order for LSL in the VDSO

   - Prevent NMI uaccess race against CR3 switching

   - Add a lockdep check to verify that text_mutex is held in
     text_poke() functions

   - Repair the fallout of giving native_restore_fl() a prototype

   - Prevent kernel memory dumps based on usermode RIP

   - Wipe KASAN shadow stack before rewinding the stack to prevent false
     positives

   - Move the AMS GOTO enforcement to the actual build stage to allow
     user API header extraction without a compiler

   - Fix a section mismatch introduced by the on demand VDSO mapping
     change

  Miscellaneous:

   - Trivial typo, GCC quirk removal and CC_SET/OUT() cleanups"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/pti: Fix section mismatch warning/error
  x86/vdso: Fix lsl operand order
  x86/mce: Fix set_mce_nospec() to avoid #GP fault
  x86/efi: Load fixmap GDT in efi_call_phys_epilog()
  x86/nmi: Fix NMI uaccess race against CR3 switching
  x86: Allow generating user-space headers without a compiler
  x86/dumpstack: Don't dump kernel memory based on usermode RIP
  x86/asm: Use CC_SET()/CC_OUT() in __gen_sigismember()
  x86/alternatives: Lockdep-enforce text_mutex in text_poke*()
  x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
  x86/irqflags: Mark native_restore_fl extern inline
  x86/build: Remove jump label quirk for GCC older than 4.5.2
  x86/Kconfig: Fix trivial typo
  x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
  x86/spectre: Add missing family 6 check to microcode check

Pull CPU hotplug fix from Thomas Gleixner:
 "Remove the stale skip_onerr member from the hotplug states"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Remove skip_onerr field from cpuhp_step structure

Pull core fixes from Thomas Gleixner:
 "A small set of updates for core code:

   - Prevent tracing in functions which are called from trace patching
     via stop_machine() to prevent executing half patched function trace
     entries.

   - Remove old GCC workarounds

   - Remove pointless includes of notifier.h"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Remove workaround for unreachable warnings from old GCC
  notifier: Remove notifier header file wherever not used
  watchdog: Mark watchdog touch functions as notrace

Fix the section mismatch warning in arch/x86/mm/pti.c:

WARNING: vmlinux.o(.text+0x6972a): Section mismatch in reference from the function pti_clone_pgtable() to the function .init.text:pti_user_pagetable_walk_pte()
The function pti_clone_pgtable() references
the function __init pti_user_pagetable_walk_pte().
This is often because pti_clone_pgtable lacks a __init
annotation or the annotation of pti_user_pagetable_walk_pte is wrong.
FATAL: modpost: Section mismatches detected.

Fixes: 85900ea5 ("x86/pti: Map the vsyscall page if needed")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/43a6d6a3-d69d-5eda-da09-0b1c88215a2a@infradead.org

Merge tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omap variants against v4.19-rc1

These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.

There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.

And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.

* tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
  ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
  arm: dts: am4372: setup rtc as system-power-controller
  ARM: dts: omap4-droid4: fix vibrations on Droid 4
  bus: ti-sysc: Fix no_console_suspend handling
  bus: ti-sysc: Fix module register ioremap for larger offsets
  ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
  ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Signed-off-by: Olof Johansson <olof@lixom.net>

In the __getcpu function, lsl is using the wrong target and destination
registers. Luckily, the compiler tends to choose %eax for both variables,
so it has been working so far.

Fixes: a582c540 ("x86/vdso: Use RDPID in preference to LSL when available")
Signed-off-by: Samuel Neves <sneves@dei.uc.pt>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180901201452.27828-1-sneves@dei.uc.pt

Pull watchdog fixlet from Wim Van Sebroeck:
 "Document support for r8a774a1"

* tag 'linux-watchdog-4.19-rc2' of git://www.linux-watchdog.org/linux-watchdog:
  dt-bindings: watchdog: renesas-wdt: Document r8a774a1 support

Pull clk fixes from Stephen Boyd:
 "Two small fixes, one for the x86 Stoney SoC to get a more accurate clk
  frequency and the other to fix a bad allocation in the Nuvoton NPCM7XX
  driver"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: x86: Set default parent to 48Mhz
  clk: npcm7xx: fix memory allocation

The trick with flipping bit 63 to avoid loading the address of the 1:1
mapping of the poisoned page while the 1:1 map is updated used to work when
unmapping the page. But it falls down horribly when attempting to directly
set the page as uncacheable.

The problem is that when the cache mode is changed to uncachable, the pages
needs to be flushed from the cache first. But the decoy address is
non-canonical due to bit 63 flipped, and the CLFLUSH instruction throws a
#GP fault.

Add code to change_page_attr_set_clr() to fix the address before calling
flush.

Fixes: 284ce401 ("x86/memory_failure: Introduce {set, clear}_mce_nospec()")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Link: https://lkml.kernel.org/r/20180831165506.GA9605@agluck-desk

Pull arm64 fixes from Will Deacon:
 "A few arm64 fixes came in this week, specifically fixing some nasty
  truncation of return values from firmware calls and resolving a
  VM_BUG_ON due to accessing uninitialised struct pages corresponding to
  NOMAP pages.

  Summary:

   - Fix typos in SVE documentation

   - Fix type-checking and implicit truncation for SMCCC calls

   - Force CONFIG_HOLES_IN_ZONE=y so that SLAB doesn't fall over NOMAP
     regions"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: mm: always enable CONFIG_HOLES_IN_ZONE
  arm/arm64: smccc-1.1: Handle function result as parameters
  arm/arm64: smccc-1.1: Make return values unsigned long
  Documentation/arm64/sve: Couple of improvements and typos

When PTI is enabled on x86-32 the kernel uses the GDT mapped in the fixmap
for the simple reason that this address is also mapped for user-space.

The efi_call_phys_prolog()/efi_call_phys_epilog() wrappers change the GDT
to call EFI runtime services and switch back to the kernel GDT when they
return. But the switch-back uses the writable GDT, not the fixmap GDT.

When that happened and and the CPU returns to user-space it switches to the
user %cr3 and tries to restore user segment registers. This fails because
the writable GDT is not mapped in the user page-table, and without a GDT
the fault handlers also can't be launched. The result is a triple fault and
reboot of the machine.

Fix that by restoring the GDT back to the fixmap GDT which is also mapped
in the user page-table.

Fixes: 7757d607 x86/pti: ('Allow CONFIG_PAGE_TABLE_ISOLATION for x86_32')
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: hpa@zytor.com
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/1535702738-10971-1-git-send-email-joro@8bytes.org

Pull xen fixes from Juergen Gross:

 - minor cleanup avoiding a warning when building with new gcc

 - a patch to add a new sysfs node for Xen frontend/backend drivers to
   make it easier to obtain the state of a pv device

 - two fixes for 32-bit pv-guests to avoid intermediate L1TF vulnerable
   PTEs

* tag 'for-linus-4.19b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  x86/xen: remove redundant variable save_pud
  xen: export device state to sysfs
  x86/pae: use 64 bit atomic xchg function in native_ptep_get_and_clear
  x86/xen: don't write ptes directly in 32-bit PV guests

Pull m68k fix from Geert Uytterhoeven:
 "Just a single fix for a bug introduced during the merge window: fix
  wrong date and time on PMU-based Macs"

* tag 'm68k-for-v4.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/mac: Use correct PMU response format

Pull i2c fixes from Wolfram Sang:

 - regression fixes for i801 and designware

 - better API and leak fix for releasing DMA safe buffers

 - better greppable strings for the bitbang algorithm

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: sh_mobile: fix leak when using DMA bounce buffer
  i2c: sh_mobile: define start_ch() void as it only returns 0 anyhow
  i2c: refactor function to release a DMA safe buffer
  i2c: algos: bit: make the error messages grepable
  i2c: designware: Re-init controllers with pm_disabled set on resume
  i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus