- 19 Feb, 2016 19 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 40GbE Intel Wired LAN Driver Updates 2016-02-19 This series contains updates to i40e/i40evf only. Alex Duyck splits up the descriptor count function from the function that stops the ring to have access to the descriptor count used for the data portion of the frame. The rewrites the logic for how we determine if we can transmit the frame or if it needs to be linearized. Place the checksum close to TSO since they have a lot in common and it can help to reduce the decision tree for how to handle the frame as the first check in TSO is to see if checksumming is offloaded. Carolyn adds functions to blink leds on devices using 10GBaseT PHY since MAC registers used in other designs do not work in this device configuration. Fixes an issue where a previously removed message has returned. Kevin increases the timeout when checking GLGEN_RSTAT_DEVSTATE bit since linking with particular PHY types, the amount of time it takes for the GLGEN_RSTAT_DEVSTATE to be set increases greatly. Neerav changes the receive queues to not wait to be disabled before DCB has been reconfigured, like transmit queues. Anjali adds new register definitions for programming the parser, flow director and RSS blocks in the hardware. Shannon adds the new opcodes and structures used for asking the firmware to update receive control registers that need extra care when being accessed while under heavy traffic. Integrates the new AdminQ functions for safely accessing the receive control registers that may be affected by heavy small packet traffic. Mitch provides another colorful patch description on letting go of the stale local VSI pointer when the VF resets. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Jesse Brandeburg authored
Bump. Change-ID: Ifa19aadaa892ad103f1b96fe2361fa690912c6a3 Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mitch Williams authored
If we reset a VF, its VSI goes away, and it gets a new one. So don't hang on to the now-stale local VSI pointer. It just leads to suffering and kernel panics. Change-ID: Ia8823b4e85893e95e963acee284968022b29177a Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Tested-by:
-
Pandi Kumar Maharajan authored
We need to suspend scheduling or any pending service task during driver unload process, so that new task will not be scheduled. This patch sets the suspend flag bit during reload which avoids service task execution. Change-ID: I017c57b5d6656564556e3c5387da671369a572ac Signed-off-by:
Pandi Kumar Maharajan <pandi.maharajan@intel.com> Tested-by:
-
Shannon Nelson authored
Use the new AdminQ functions for safely accessing the Rx control registers that may be affected by heavy small packet traffic. We can't use AdminQ calls in i40e_clear_hw() because the HW is being initialized and the AdminQ is not alive. We recently added an AQ related replacement for reading PFLAN_QALLOC, and this patch puts back the original register read. Change-ID: Ib027168c954a5733299aa3a4ce5f8218c6bb5636 Signed-off-by:
Shannon Nelson <shannon.nelson@intel.com> Tested-by:
-
Shannon Nelson authored
Use the new AdminQ functions for safely accessing the Rx control registers that may be affected by heavy small packet traffic. Change-ID: Ibb00983e8dcba71f4b760222a609a5fcaa726f18 Signed-off-by:
-
Shannon Nelson authored
Add the new opcodes and struct used for asking the firmware to update Rx control registers that need extra care when being accessed while under heavy traffic - e.g. sustained 64byte packets at line rate on all ports. The firmware will take extra steps to be sure the register accesses are successful. The registers involved are: PFQF_CTL_0 PFQF_HENA PFQF_FDALLOC PFQF_HREGION PFLAN_QALLOC VPQF_CTL VFQF_HENA VFQF_HREGION VSIQF_CTL VSILAN_QBASE VSILAN_QTABLE VSIQF_TCREGION PFQF_HKEY VFQF_HKEY PRTQF_CTL_0 GLFCOE_RCTL GLFCOE_RSOF GLQF_CTL GLQF_SWAP GLQF_HASH_MSK GLQF_HASH_INSET GLQF_HSYM GLQF_FC_MSK GLQF_FC_INSET GLQF_FD_MSK PRTQF_FD_INSET PRTQF_FD_FLXINSET PRTQF_FD_MSK Change-ID: I56c8144000da66ad99f68948d8a184b2ec2aeb3e Signed-off-by:
-
John Underwood authored
Return from i40e_vsi_reinit_setup() if vsi param is NULL. This makes this code consistent with all the other code that checks for NULL before using one of the VSI pointers accessed with an indexed variable. (Indexed VSI pointers are intentionally set to NULL in i40e_vsi_clear() and i40e_remove(). Change-ID: I3bc8b909c70fd2439334eeae994d151f61480985 Signed-off-by:
John Underwood <johnx.underwood@intel.com> Tested-by:
-
Anjali Singhai Jain authored
This patch adds 7 new register definitions for programming the parser, flow director and RSS blocks in the HW. Change-ID: I31e76673125275f3c69a14c646361919d04dc987 Signed-off-by:
Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by:
-
Carolyn Wyborny authored
This fixes an issue where a previously removed message has returned. Changing the message type to dev_dbg leaves the info, if desired, but takes it out of normal everyday usage. Also changed call to only provide port data when its valid and not when its not (delete case). Change-ID: Ief6f33b915f6364c24fa8e5789c2fc3168b5e2ed Signed-off-by:
Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by:
-
Neerav Parikh authored
Just like Tx queues don't wait for Rx queues to be disabled before DCB has been reconfigured. Check the queues are disabled only after the DCB configuration has been applied to the VSI(s) managed by the PF driver. In case of any timeout issue a PF reset to recover. Change-ID: Ic51e94c25baf9a5480cee983f35d15575a88642c Signed-off-by:
Neerav Parikh <neerav.parikh@intel.com> Tested-by:
-
Kevin Scott authored
When linking with particular PHY types (ex: copper PHY), the amount of time it takes for the GLGEN_RSTAT_DEVSTATE to be set increases greatly, which can lead to a timeout and failure to load the driver. Change-ID: If02be0dfcd7c57fdde2d5c81cd63651260cd2029 Signed-off-by:
Kevin Scott <kevin.c.scott@intel.com> Tested-by:
-
Carolyn Wyborny authored
This patch fixes a problem where the ethtool identify adapter functionality did not work for some copper PHY's. Without this patch, the blink led functionality fails on some parts. This patch adds PHY write code to blink led's on parts where this functionality is contained in the PHY rather than the MAC. Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2 Signed-off-by:
-
Carolyn Wyborny authored
This patch adds functions to blink led on devices using 10GBaseT PHY since MAC registers used in other designs do not work in this device configuration. Change-ID: Id4b88c93c649fd2b88073a00b42867a77c761ca3 Signed-off-by:
-
Alexander Duyck authored
On all of the other Intel drivers we place checksum close to TSO as they have a significant amount in common and it can help to reduce the decision tree for how to handle the frame as the first check in TSO is to see if checksumming is offloaded, and if it is not we can skip _BOTH_ TSO and Tx checksum offload based on a single check. Signed-off-by:
Alexander Duyck <aduyck@mirantis.com> Tested-by:
-
Alexander Duyck authored
This patch is meant to rewrite the logic for how we determine if we can transmit the frame or if it needs to be linearized. The previous code for this function was using a mix of division and modulus division as a part of computing if we need to take the slow path. Instead I have replaced this by simply working with a sliding window which will tell us if the frame would be capable of causing a single packet to span several descriptors. The logic for the scan is fairly simple. If any given group of 6 fragments is less than gso_size - 1 then it is possible for us to have one byte coming out of the first fragment, 6 fragments, and one or more bytes coming out of the last fragment. This gives us a total of 8 fragments which exceeds what we can allow so we send such frames to be linearized. Arguably the use of modulus might be more exact as the approach I propose may generate some false positives. However the likelihood of us taking much of a hit for those false positives is fairly low, and I would rather not add more overhead in the case where we are receiving a frame composed of 4K pages. Signed-off-by:
-
Alexander Duyck authored
In an upcoming patch I would like to have access to the descriptor count used for the data portion of the frame. For this reason I am splitting up the descriptor count function from the function that stops the ring. Also in order to try and reduce unnecessary duplication of code I am moving the slow-path portions of the code out of being inline calls so that we can just jump to them and process them instead of having to build them into each function that calls them. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 40GbE Intel Wired LAN Driver Updates 2016-02-18 This series contains updates to i40e and i40evf only. Alex Duyck provides all the patches in the series to update and fix the drivers. Fixed the driver to drop the outer checksum offload on UDP tunnels, since the issue is that the upper levels of the stack never requested such an offload and it results in possible errors. Updates the TSO function to just use u64 values, so we do not have to end up casting u32 values. In the TSO path, factored out the L4 header offsets allowing us to ignore the L4 header offsets when dealing with the L3 checksum and length update. Consolidates all of the spots where we were updating either the TCP or IP checksums in the TSO and checksum path into the TSO function. Fixed two issues by adding support for IPv4 encapsulated in IPv6, first issue was the fact that iphdr(skb)->protocol was being used to test for the outer transport protocol which breaks IPv6 support. The second was that we cleared the flag for v4 going to v6, but we did not take care of txflags going the other way. Added support for IPv6 extension headers in setting up the Tx checksum. Added exception handling to the Tx checksum path so that we can handle cases of TSO where the frame is bad, or Tx checksum where we did not recognize a protocol. Fixed a number of issues to make certain that we are using the correct protocols when parsing both the inner and outer headers of a frame that is mixed between IPv4 and IPv6 for inner and outer. Updated the feature flags to reflect the newly enabled/added features. Sorry, no witty patch descriptions this time around, probably should let Mitch help in writing patch descriptions for Alex. :-) ==================== Signed-off-by: -
Yuval Mintz authored
Commit e5d3a51c ("bnx2x: extend DCBx support") was missing HSI changes for big-endian machine, breaking compilation on such platforms. Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
-
- 18 Feb, 2016 21 commits
-
-
Alexander Duyck authored
This patch updates the code for determining the L4 protocol and L3 header length so that when IPv6 extension headers are being used we can determine the offset and type of the L4 protocol. Signed-off-by:
-
Alexander Duyck authored
Recent changes should have enabled support for IPv6 based tunnels and support for TSO with outer UDP checksums. As such we can update the feature flags to reflect that. In addition we can clean-up the flags that aren't needed such as SCTP and RXCSUM since having the bits there doesn't add any value. I also found one spot where we were setting the same flag twice. It looks like it was probably a git merge error that resulted in the line being duplicated. As such I have dropped it in this patch. Signed-off-by:
-
Alexander Duyck authored
Recent changes should have enabled support for IPv6 based tunnels and support for TSO with outer UDP checksums. As such we can update the feature flags to reflect that. In addition we can clean-up the flags that aren't needed such as SCTP and RXCSUM since having the bits there doesn't add any value. Signed-off-by:
-
Alexander Duyck authored
All of the documentation in the datasheets for the XL710 do not call out any reason to exclude support for IPv6 based tunnels. As such I am dropping the code that was excluding these tunnel types from having their port numbers recognized. This way we can take advantage of things such as checksum offload for inner headers over IPv6 based VXLAN or GENEVE tunnels. Signed-off-by:
-
Alexander Duyck authored
This patch contains a number of fixes to make certain that we are using the correct protocols when parsing both the inner and outer headers of a frame that is mixed between IPv4 and IPv6 for inner and outer. Signed-off-by:
Kiran Patil <kiran.patil@intel.com> Tested-by:
-
Alexander Duyck authored
The XL722 has support for providing the outer UDP tunnel checksum on transmits. Make use of this feature to support segmenting UDP tunnels with outer checksums enabled. Signed-off-by:
-
Alexander Duyck authored
This is mostly a minor clean-up for the Rx checksum path in order to avoid some of the unnecessary conditional checks that were being applied. Signed-off-by:
-
David S. Miller authored
Yuval Mintz says: ==================== qed{,e}: Add vlan filtering offload This series adds vlan filtering offload to qede. First patch introduces small additional infrastructure needed in qed to support it, while second contains the main bulk of driver changes. ==================== Signed-off-by: -
Sudarsana Reddy Kalluru authored
Device would start receiving only vlan-tagged traffic with tags matching that of one of the configured vlan IDs, unless: - Device is expliicly placed in PROMISC mode. - Device exhausts its vlan filter credits. Signed-off-by:
Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by:
-
Yuval Mintz authored
Today, interfaces are working in vlan-promisc mode; But once vlan filtering offloaded would be supported, we'll need a method to control it directly [e.g., when setting device to PROMISC, or when running out of vlan credits]. This adds the necessary API for L2 client to manually choose whether to accept all vlans or only those for which filters were configured. Signed-off-by:
-
Andrew F. Davis authored
Files in sysfs are created using the name from the phy_driver struct, when two names are the same we may get a duplicate filename warning, fix this. Reported-by:
kernel test robot <ying.huang@linux.intel.com> Signed-off-by:
Andrew F. Davis <afd@ti.com> Signed-off-by:
-
Alexander Duyck authored
This patch takes advantage of several assumptions we can make about the headers of the frame in order to reduce overall processing overhead for computing the outer header checksum. First we can assume the entire header is in the region pointed to by skb->head as this is what csum_start is based on. Second, as a result of our first assumption, we can just call csum_partial instead of making a call to skb_checksum which would end up having to configure things so that we could walk through the frags list. Signed-off-by:
-
Benjamin Poirier authored
follows up commit 45f6fad8 ("ipv6: add complete rcu protection around np->opt") which added mixed rcu/refcount protection to np->opt. Given the current implementation of rcu_pointer_handoff(), this has no effect at runtime. Signed-off-by:
Benjamin Poirier <bpoirier@suse.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
David S. Miller authored
Jiri Benc says: ==================== iptunnel: scrub packet in iptunnel_pull_header As every IP tunnel has to scrub skb on decapsulation, iptunnel_pull_header tried to do that and open coded part of skb_scrub_packet. Various tunneling protocols (VXLAN, Geneve) then called full skb_scrub_packet on their own, duplicating part of the scrubbing already done. Consolidate the code, calling skb_scrub_packet from iptunnel_pull_header. This will allow additional cleanups in VXLAN code, as the packet is scrubbed early during rx processing after this patchset and VXLAN can start filling out skb fields earlier. The full picture of vxlan cleanup patches can be seen at: https://github.com/jbenc/linux-vxlan/commits/master ==================== Signed-off-by:
-
Jiri Benc authored
Part of skb_scrub_packet was open coded in iptunnel_pull_header. Let it call skb_scrub_packet directly instead. Signed-off-by:
Jiri Benc <jbenc@redhat.com> Signed-off-by:
-
Jiri Benc authored
This is in preparation for iptunnel_pull_header calling skb_scrub_packet. Signed-off-by:
-
Jiri Benc authored
This is in preparation for iptunnel_pull_header calling skb_scrub_packet. Signed-off-by:
-
Jiri Benc authored
Similarly to the existing vxlan_get_sk_family. Signed-off-by:
-
Vivien Didelot authored
Remove the shared br_log_state function and print the info directly in br_set_state, where the net_bridge_port state is actually changed. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
David S. Miller authored
Hariprasad Shenai says: ==================== cxgb4: Use __dev_[um]c_[un]sync for MAC address syncing This patch series adds support to use __dev_uc_sync/__dev_mc_sync to add MAC address and __dev_uc_unsync/__dev_mc_unsync to delete MAC address. This patch series has been created against net-next tree and includes patches on cxgb4 and cxgb4vf driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. ==================== Signed-off-by: -
Hariprasad Shenai authored
Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
-
