Add support for multiple mst stream in hdcp port data
which will be used by RepeaterAuthStreamManage msg and
HDCP 2.2 security f/w for m' validation.

Security f/w doesn't have any provision to mark the stream_type
for each stream separately, it just take single input of
stream_type while authenticating the port and applies the
same stream_type to all streams. So driver mark each stream_type
with common highest supported content type for all streams
in DP MST Topology.

Security f/w supports RepeaterAuthStreamManage msg and m'
validation only once during port authentication and encryption.
Though it is not compulsory, security fw should support dynamic
update of content_type and should support RepeaterAuthStreamManage
msg and m' validation whenever required.

v2:
- Init the hdcp port data k for HDMI/DP SST stream.
v3:
- Cosmetic changes. [Uma]
v4:
- 's/port_auth/hdcp_port_auth'. [Ram]
- Commit log improvement.
v5:
- Comment and commit log improvement. [Ram]
v6:
- Check first connector connected status before intel_encoder_is_mst
  to avoid any NULL pointer dereference.

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Juston Li <juston.li@intel.com>
Acked-by: Juston Li <juston.li@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-15-anshuman.gupta@intel.com

Let's define Maximum MST content streams up to four
generically which can be supported by modern display
controllers.

Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-14-anshuman.gupta@intel.com

Fix the size of WIRED_REPEATER_AUTH_STREAM_REQ cmd buffer size.
It is based upon the actual number of MST streams and size
of wired_cmd_repeater_auth_stream_req_in.
Excluding the size of hdcp_cmd_header.

v2:
- hdcp_cmd_header size annotation nitpick. [Tomas]

Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-13-anshuman.gupta@intel.com

hdcp_port_data is specific to a port on which HDCP
encryption is getting enabled, so encapsulate it to
intel_digital_port.
This will be required to enable HDCP 2.2 stream encryption.

v2:
- 's/port_data/hdcp_port_data'. [Ram]

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-12-anshuman.gupta@intel.com

Pass dig_port as an argument to intel_hdcp_init()
and intel_hdcp2_init().
This will be required for HDCP 2.2 stream encryption.

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-11-anshuman.gupta@intel.com

Enable HDCP 1.4 over DP MST for Gen12.

v2:
- Enable HDCP for <= Gen12 platforms. [Ram]
v3:
- Connector detials in debug msg. [Ram]

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-10-anshuman.gupta@intel.com

Enable HDCP 1.4 DP MST stream encryption.

Enable stream encryption once encryption is enabled on
the DP transport driving the link for each stream which
has requested encryption.

Disable stream encryption for each stream that no longer
requires encryption before disabling HDCP encryption on
the link.

v2:
- Added debug print for stream encryption.
- Disable the hdcp on port after disabling last stream
  encryption.
v3:
- Cosmetic change, removed the value less comment. [Uma]
v4:
- Split the Gen12 HDCP enablement patch. [Ram]
- Add connector details in drm_err.
v5:
- uniformity for connector detail in DMESG. [Ram]
- comments improvement. [Ram]

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-9-anshuman.gupta@intel.com

Both HDCP_{1.x,2.x} requires to select/deselect Multistream HDCP bit
in TRANS_DDI_FUNC_CTL in order to enable/disable stream HDCP
encryption over DP MST Transport Link.

HDCP 1.4 stream encryption requires to validate the stream encryption
status in HDCP_STATUS_{TRANSCODER,PORT} register driving that link
in order to enable/disable the stream encryption.

Both of above requirement are same for all Gen with respect to
B.Spec Documentation.

v2:
- Cosmetic changes function name, error msg print and
  stream typo fixes. [Uma]
v3:
- uniformity for connector detail in DMESG. [Ram]

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-8-anshuman.gupta@intel.com

DP MST stream encryption status requires time of a link frame
in order to change its status, but as there were some HDCP
encryption timeout observed earlier, it is safer to use
ENCRYPT_STATUS_CHANGE_TIMEOUT_MS timeout for stream status too,
it requires to move the macro to a header.
It will be used by both HDCP{1.x,2.x} stream status timeout.

Related: 'commit 7e90e8d0 ("drm/i915: Increase timeout for Encrypt
status change")'
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-7-anshuman.gupta@intel.com

Gen12 has H/W delta with respect to HDCP{1.x,2.x} display engine
instances lies in Transcoder instead of DDI as in Gen11.

This requires hdcp driver to use mst_master_transcoder for link
authentication and stream transcoder for stream encryption
separately.

This will be used for both HDCP 1.4 and HDCP 2.2 over DP MST
on Gen12.

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-6-anshuman.gupta@intel.com

There can be situation when DP MST connector is created without
mst modeset being done, in those cases connector->encoder will be
NULL. MST connector->encoder initializes after modeset.
Don't enable HDCP in such cases to prevent any crash.

Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Juston Li <juston.li@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-5-anshuman.gupta@intel.com

Handle CP_IRQ in DEVICE_SERVICE_IRQ_VECTOR_ESI0
It requires to call intel_hdcp_handle_cp_irq() in case
of CP_IRQ is triggered by a sink in DP-MST topology.

Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-4-anshuman.gupta@intel.com

Get DRM connector reference count while scheduling a prop work
to avoid any possible destroy of DRM connector when it is in
DRM_CONNECTOR_REGISTERED state.

Fixes: a6597faa ("drm/i915: Protect workers against disappearing connectors")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-3-anshuman.gupta@intel.com

When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.

This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.

v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
  WARN_ON.

v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]

Fixes: 33f9a623 ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com

DG1's vswing tables are the same for eDP and HDMI but have slight
differences from ICL/TGL for DP.

v2:
 - Use a "_hbr2_hbr3" suffix on the table name to make it more clear
   that the same table is used for both HBR2 and HBR3 link rates.
   (Swathi)

Bspec: 49291
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108222528.1954514-1-matthew.d.roper@intel.comReviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>

Some new eDP panels don't like to operate at the max parameters, and
instead we need to go for an optimal confiugration. That unfortunately
doesn't work with older eDP panels which are generally only guaranteed
to work at the max parameters.

To solve these two conflicting requirements let's start with the optimal
setup, and if that fails we start again with the max parameters. The
downside is probably an extra modeset when we switch strategies but
I don't see a good way to avoid that.

For a bit of history we first tried to go for the fast+narrow in
commit 7769db58 ("drm/i915/dp: optimize eDP 1.4+ link config
fast and narrow"). but that had to be reverted due to regression
on older panels in commit f11cb1c1 ("drm/i915/dp: revert back
to max link rate and lane count on eDP"). So now we try to get
the best of both worlds by using both strategies.

v2: Deal with output_bpp and uapi vs. hw state split
    Reword some comments
v3: Rebase

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Albert Astals Cid <aacid@kde.org> # v5.0 backport
Cc: Emanuele Panigati <ilpanich@gmail.com> # v5.0 backport
Cc: Matteo Iervasi <matteoiervasi@gmail.com> # v5.0 backport
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=105267
References: https://bugs.freedesktop.org/show_bug.cgi?id=109959
References: https://gitlab.freedesktop.org/drm/intel/issues/272Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107182026.24848-1-ville.syrjala@linux.intel.com

Eliminate checkpatch warnings from intel_cursor.c:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Possible repeated word: 'by'
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110175624.3524-2-ville.syrjala@linux.intel.comReviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>

There was some misinterpretation of specification, when DDIX_USED is
set, the next bit means 0 for DP and 1 for HDMI.

Anyways this misinterpretation is not causing any issues, this change
is just to comply with specification.
Also as for us it do not matters if it is HDMI or DP, not checking the
port type that HTI is using.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108134802.21280-1-jose.souza@intel.com

The pch_get_backlight(), lpt_get_backlight(), and lpt_set_backlight()
functions operate directly on the hardware registers. If inverting the
value is needed, using intel_panel_compute_brightness(), it should only
be done in the interface between hardware registers and
panel->backlight.level.

The CPU mode takeover code added in commit 5b1ec9ac
("drm/i915/backlight: Fix backlight takeover on LPT, v3.") reads the
hardware register and converts to panel->backlight.level correctly,
however the value written back should remain in the hardware register
"domain".

This hasn't been an issue, because GM45 machines are the only known
users of i915.invert_brightness and the brightness invert quirk, and
without one of them no conversion is made. It's likely nobody's ever hit
the problem.

Fixes: 5b1ec9ac ("drm/i915/backlight: Fix backlight takeover on LPT, v3.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108152841.6944-1-jani.nikula@intel.com

As with the regular suspend paths, also disable the wakeref assertions
as we disable the driver during shutdown.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2899
Fixes: fe0f1e3b ("drm/i915: Shut down displays gracefully on reboot")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104203905.19248-1-chris@chris-wilson.co.uk

We need a power_domain wakeref in pps_{lock,unlock} to prevent
a race while resetting pps state in intel_power_sequencer_reset().

intel_power_sequencer_reset() need a pps_mutex to access pps_pipe
but it can't grab pps_mutex due to deadlock with power_well
functions are called while holding pps_mutex.
intel_power_sequencer_reset() is called by power_well function
associated with legacy platforms like vlv and chv therefore re-use
the POWER_DOMAIN_DISPLAY_CORE power domain, which only used
by vlv and chv display power domain.

This will avoids the unnecessary noise of unrelated power wells
in pps_{lock,unlock}.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107112500.16216-1-anshuman.gupta@intel.com

sync-up to not fall too much behind.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm-misc-next for v5.12:

Core Changes:
- Lots of drm documentation updates by Simor Ser.
- Require that each crtc has a unique primary plane.
- Add fixme that fbdev_generic_setup is confusing.

Driver Changes:
- Update addresses for TI display drivers maintainers.
- Make DRM_VIRTIO_GPU select VIRTIO.
- Small fixes to qxl, virtio, hisilicon, tve200, panel/s6e63m0.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fdfbfd7a-b91d-3f59-11c8-984704ce0ee1@linux.intel.com

- Add default modes for connectors in unknown state
- R-Car DU conversion to DRM-managed API
- R-Car DU miscellaneous fixes
- Miscellaneous bridge and bridge bindings fixes
- Assorted misc driver cleanups
- Constify drm_driver for PCI devices
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/X/P8IOrVXkTpLeCm@pendragon.ideasonboard.com

- Display hotplug fix for gen2/gen3 (Chris)
- Remove trailing semicolon (Tom)
- Suppress display warnings for old ifwi presend on our CI (Chris)
- OA/Perf related workaround (Lionel)
- Replace I915_READ/WRITE per new uncore and display read/write functions (Jani)
- PSR improvements (Jose)
- HDR and other color changes on LSPCON (Uma, Ville)
- FBC fixes for TGL (Uma)
- Record plane update times for debugging (Chris)
- Refactor panel backlight control functions (Dave)
- Display power improvements (Imre)
- Add VRR register definition (Manasi)
- Atomic modeset improvements for bigjoiner pipes (Ville)
- Switch off the scanout during driver unregister (Chris)
- Clean-up DP's FEW enable (Manasi)
- Fix VDSCP slice count (Manasi)
- Fix and clean up around rc_model_size for DSC (Jani)
- Remove Type-C noisy debug warn message (Sean)
- Display HPD code clean-up (Ville)
- Refactor Intel Display (Dave)
- Start adding support for Intel's eDP backlight controls (Lyude)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104211018.GA1094707@intel.com

drm/i915/dsi: Use unconditional msleep for the panel_on_delay when there is no reset-deassert MIPI-sequence

Commit 25b4620e ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
added an intel_dsi_msleep() helper which skips sleeping if the
MIPI-sequences have a version of 3 or newer and the panel is in vid-mode;
and it moved a bunch of msleep-s over to this new helper.

This was based on my reading of the big comment around line 730 which
starts with "Panel enable/disable sequences from the VBT spec.",
where the "v3 video mode seq" column does not have any wait t# entries.

Given that this code has been used on a lot of different devices without
issues until now, it seems that my interpretation of the spec here is
mostly correct.

But now I have encountered one device, an Acer Aspire Switch 10 E
SW3-016, where the panel will not light up unless we do actually honor the
panel_on_delay after exexuting the MIPI_SEQ_PANEL_ON sequence.

What seems to set this model apart is that it is lacking a
MIPI_SEQ_DEASSERT_RESET sequence, which is where the power-on
delay usually happens.

Fix the panel not lighting up on this model by using an unconditional
msleep(panel_on_delay) instead of intel_dsi_msleep() when there is
no MIPI_SEQ_DEASSERT_RESET sequence.

Fixes: 25b4620e ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201118124058.26021-1-hdegoede@redhat.com

drm/imx: fixes and drm managed resources

- Reduce stack usage in ipu-di.
- Fix imx-ldb for compile tests.
- Make drm encoder control functions optional.
- Add drm managed variants drmm_encoder_alloc(),
  drmm_simple_encoder_alloc(), drmm_universal_plane_alloc(), and
  drmm_crtc_alloc_with_planes() for drm_encoder_init(),
  drm_simple_encoder_init(), drm_universal_plane_init(), and
  drm_crtc_init_with_planes(), respectively.
- Update imx-drm to use the new functions for drm managed resource
  allocation, moving initialization from bind to probe where possible.
- Fix imx-tve clock provider leak.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[danvet: Fix conflict between doc changes by both Philipp and Simon
Ser, see 9999587b ("drm: rework description of primary and cursor
planes")]
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/c745fc1596898932c9454fd2979297b4242566a2.camel@pengutronix.de

Merge tag 'topic/dp-hdmi-2.1-pcon-2020-12-23' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

Add support for DP-HDMI2.1 PCON

From the series cover letter:

This patch series attempts to add support for a DP-HDMI2.1 Protocol
Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
E5 to DisplayPort_v2.0:
https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
The details are mentioned in:
VESA DP-to-HDMI PCON Specification Standalone Document
https://groups.vesa.org/wg/DP/document/15651

This series starts with adding support for FRL (Fixed Rate Link)
Training between the PCON and HDMI2.1 sink.
As per HDMI2.1 specification, a new data-channel or lane is added in
FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
lanes).

With these patches, the HDMI2.1 PCON can be configured to achieve FRL
training based on the maximum FRL rate supported by the panel, source
and the PCON.
The approach is to add the support for FRL training between PCON and
HDMI2.1 sink and gradually add other blocks for supporting higher
resolutions and other HDMI2.1 features, that can be supported by pcon
for the sources that do not natively support HDMI2.1.

This is done before the DP Link training between the source and PCON
is started. In case of FRL training is not achieved, the PCON will
work in the regular TMDS mode, without HDMI2.1 feature support.
Any interruption in FRL training between the PCON and HDMI2.1 sink is
notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
registers are read and FRL training is re-attempted.

Currently, we have tested the FRL training and are able to enable 4K
display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
panel.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lfdpndkt.fsf@intel.com

drm-misc-next for v5.12:

UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.

Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.

Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.

Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/78381a4f-45fd-aed4-174a-94ba051edd37@linux.intel.com

The bspec has been updated with new vswing programming for RKL DP.  No
data is provided for HDMI or eDP, so for now we'll continue to assume
that those are the same as TGL.

Bspec: 49291
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218040535.45492-1-matthew.d.roper@intel.comReviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>

After boot into kernel. Driver configured ddc pin mapping based on
predefined table in parse_ddi_port(). Now driver configure rkl
ddc pin mapping depends on icp_ddc_pin_map[]. Then this table will
give incorrect gmbus port number to cause HDMI can't work.

Refer to commit cd0a8952 ("drm/i915/rkl: Add DDC pin mapping").
Create two ddc pin table for rkl TGP and CMP pch. Then HDMI can
works properly on rkl.

v2: update patch based on latest dinq branch.
v3: update ddc table for RKL+TGP sku.
    RKL+CNP sku will load cnp_ddc_pin_map[] setting.
v4: modify the if/else judgment to avoid nesting.
v5: fix typo in v4.

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2577Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117142629.28729-1-shawn.c.lee@intel.com

gvt-next-fixes-2020-12-25

- Avoid one useless inline (Jani)
- make gvt header self-contained, fix CONFIG_DRM_I915_WERROR (Jani)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201225022009.GF16939@zhen-hp.sh.intel.com

It programs Plane's calculated x, y, offset to Plane SF register.
It does the calculation of x and y offsets using
skl_calc_main_surface_offset().

v3: Update commit message

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-4-jose.souza@intel.com

The calculation the offsets of the main surface will be needed by PSR2
selective fetch code so here splitting and exporting it.
No functional changes were done here.

v3: Rebased

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-3-jose.souza@intel.com

Now using plane damage clips property to calcualte the damaged area.
Selective fetch only supports one region to be fetched so software
needs to calculate a bounding box around all damage clips.

Now that we are not complete fetching each plane, there is another
loop needed as all the plane areas that intersect with the pipe
damaged area needs to be fetched from memory so the complete blending
of all planes can happen.

v2:
- do not shifting new_plane_state->uapi.dst only src is in 16.16 format

v4:
- setting plane selective fetch area using the whole pipe damage area
- mark the whole plane area damaged if plane visibility or alpha
changed

v5:
- taking in consideration src.y1 in the damage coordinates
- adding to the pipe damaged area planes that were visible but are
invisible in the new state

v6:
- consider old state plane coordinates when visibility changes or it
moved to calculate damaged area
- remove from damaged area the portion not in src clip

v7:
- intersec every damage clip with src to minimize damaged area

v8:
- adjust pipe_damaged area to 4 lines grouping
- adjust calculation now that is understood that uapi.src is the
framebuffer coordinates that plane will start to fetch from

v9:
- Only add plane dst or src to damaged_area if visible
- Early skip plane damage calculation if it was not visible in old and
new state

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-2-jose.souza@intel.com

Much more clear to read one function call than four lines doing this
conversion.

v7:
- function renamed
- calculating width and height before truncate
- inlined

v10:
- renamed parameters from source and destination to src and dst
to match sister functions

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-1-jose.souza@intel.com

It doesn't seem like drm.h docs are included anywhere. Render them next
to drm_mode.h, under the "Userspace API Structures" section.

This also allows references to e.g. DRM_CAP_* to be properly linkified
elsewhere in our docs.
Signed-off-by: Simon Ser <contact@emersion.fr>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201222133524.160842-6-contact@emersion.fr

Sphinx doesn't like old doc-comments in drm.h and generates warnings
like:

    ./include/uapi/drm/drm.h:87: warning: cannot understand function prototype: 'struct drm_clip_rect '
    ./include/uapi/drm/drm.h:97: warning: cannot understand function prototype: 'struct drm_drawable_info '
    ./include/uapi/drm/drm.h:105: warning: cannot understand function prototype: 'struct drm_tex_region '
    ...

Demote these to regular comments, because converting all of them is
quite a lot of work (also requires documenting all of the struct fields
for instance). Also many of these structures aren't really used by
modern user-space.

We can easily convert these remaining old comments to Sphinx style on a
one-by-one basis.
Signed-off-by: Simon Ser <contact@emersion.fr>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201222133524.160842-5-contact@emersion.fr

Our documentation build system chokes on \file comments:

    ./include/uapi/drm/drm.h:2: warning: Cannot understand  * \file drm.h
     on line 2 - I thought it was a doc line

Remove all of the slash-directives, and demote to a normal comment. Keep
the historical information because it predates Git.

v3: keep the comment (Daniel)
Signed-off-by: Simon Ser <contact@emersion.fr>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201222133524.160842-4-contact@emersion.fr

Because clk_disable_unprepare() already checked NULL clock parameter,
so the additional check is unnecessary, just remove them.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>