Define the R8A7790 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This clock drives the INTCA irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: devicetree@vger.kernel.org
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Renesas ARM Based SoC r8a73a4 DT Timers Updates for v3.19

* Initialise CMT1 timer using DT

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The DU device is now instantiated from the device tree, remove the
corresponding platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The DU device is now instantiated from the device tree, remove the
corresponding platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Mitsubishi AA104XD12 panel is commonly used with the Marzen, Lager
and Koelsch boards. Create a .dtsi file that describe the panel and its
connection to the board.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: resolved minor conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: resolved minor conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The information is already included in the COPYING file in the kernel
sources root directory, we don't want to modify all source files when
the FSF will move to a new address, and I'm tired of seeing the related
checkpatch.pl warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

r8a73a4_add_dt_devices() no longer enables any devices
so remove it.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Initialise CMT1 device using DT when booting ape6evm
using DT-reference.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Rename r8a7790_register_cmt() as r8a73a4_register_cmt() to
reflect name of the SoC in use. The use of r8a7790 appears
to be due to historical sharing of code from that SoC.
Shared code is no longer used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This describes all of the CMT1 hardware of the r8a73a4.
The node is disabled and may be enabled as necessary by board DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=ttyS1,115200n81" parameter in
chosen/bootargs, else the console will use the default setting of 9600
baud.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
In addition, this will allow the PM domain code to find the PM domain
for the console device.

Note that we have to keep the "console=ttySC4" parameter in
chosen/bootargs, else we only get console messages on tty0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=ttySC0,38400" parameter in
chosen/bootargs, else the console will use the default setting of 115200
baud.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=" parameter in chosen/bootargs,
as this DTS is shared between legacy and multi-platform.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=ttySC0,38400" parameter in
chosen/bootargs, else the console will use the default setting of 115200
baud.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=" parameter in chosen/bootargs,
as this DTS is shared between legacy and multi-platform.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=" parameter in chosen/bootargs,
as this DTS is shared between legacy and multi-platform.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Remove the now-superfluous "console=" parameter from chosen/bootargs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
In addition, this will allow the PM domain code to find the PM domain
for the console device.

Note that we have to keep the "console=ttySC1" parameter in
chosen/bootargs, else we only get console messages on tty0, and because
this DTS is shared between legacy and multi-platform.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
In addition, this will allow the PM domain code to find the PM domain
for the console device.

Remove the now-superfluous "console=" parameter from chosen/bootargs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Remove the now-superfluous "console=" parameter from chosen/bootargs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

smu -> clocks
sti -> timer
uart -> serial

All but "clocks" are defined in ePAPR v1.1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Forgotten by commit ad8c3af8 ("ARM: shmobile: r7s72100: Remove
legacy board support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[horms+renesas@verge.net.au: updated for removal of dma-multiplexer base
 address]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As there is no reg property the dma-multiplexer nodes should
not include @...
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms+renesas@verge.net.au:  update for addition of r8a7794-alt.dtb]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Pull ARM SoC fixes from Olof Johansson:
 "A batch of fixes that have come in during the merge window.

  Some of them are defconfig updates for things that have now landed,
  some errata additions and a few general scattered fixes.

  There's also a qcom DT update that adds support for SATA on AP148, and
  basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
  isolated enough that we could merge it even if it's late"

* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: corrected bcm2835 search
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148
  MAINTAINERS: Update Santosh Shilimkar's email id
  ARM: sunxi_defconfig: enable CONFIG_REGULATOR
  ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
  ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
  ARM: exynos_defconfig: enable USB gadget support
  ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
  ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
  ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
  ARM: SAMSUNG: Restore Samsung PM Debug functionality
  ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
  ARM: exynos_defconfig: Enable SBS battery support
  ARM: exynos_defconfig: Enable Control Groups support
  ARM: exynos_defconfig: Enable Atmel maXTouch support
  ARM: exynos_defconfig: Enable MAX77802

Pull audit updates from Eric Paris:
 "So this change across a whole bunch of arches really solves one basic
  problem.  We want to audit when seccomp is killing a process.  seccomp
  hooks in before the audit syscall entry code.  audit_syscall_entry
  took as an argument the arch of the given syscall.  Since the arch is
  part of what makes a syscall number meaningful it's an important part
  of the record, but it isn't available when seccomp shoots the
  syscall...

  For most arch's we have a better way to get the arch (syscall_get_arch)
  So the solution was two fold: Implement syscall_get_arch() everywhere
  there is audit which didn't have it.  Use syscall_get_arch() in the
  seccomp audit code.  Having syscall_get_arch() everywhere meant it was
  a useless flag on the stack and we could get rid of it for the typical
  syscall entry.

  The other changes inside the audit system aren't grand, fixed some
  records that had invalid spaces.  Better locking around the task comm
  field.  Removing some dead functions and structs.  Make some things
  static.  Really minor stuff"

* git://git.infradead.org/users/eparis/audit: (31 commits)
  audit: rename audit_log_remove_rule to disambiguate for trees
  audit: cull redundancy in audit_rule_change
  audit: WARN if audit_rule_change called illegally
  audit: put rule existence check in canonical order
  next: openrisc: Fix build
  audit: get comm using lock to avoid race in string printing
  audit: remove open_arg() function that is never used
  audit: correct AUDIT_GET_FEATURE return message type
  audit: set nlmsg_len for multicast messages.
  audit: use union for audit_field values since they are mutually exclusive
  audit: invalid op= values for rules
  audit: use atomic_t to simplify audit_serial()
  kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
  audit: reduce scope of audit_log_fcaps
  audit: reduce scope of audit_net_id
  audit: arm64: Remove the audit arch argument to audit_syscall_entry
  arm64: audit: Add audit hook in syscall_trace_enter/exit()
  audit: x86: drop arch from __audit_syscall_entry() interface
  sparc: implement is_32bit_task
  sparc: properly conditionalize use of TIF_32BIT
  ...

Merge tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes

Merge "qcom DT changes for v3.18-3" from Kumar Gala:

Qualcomm ARM Based Device Tree Updates for v3.18-3

* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148

* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148