The sighand pointer only needs the rcu_read_lock on the
read side.  So only depending on task_lock protection
when setting this pointer is not enough.  We also need
a memory barrier to ensure the initialization is seen first.

Use rcu_assign_pointer as it does this for us, and clearly
documents that we are setting an rcu readable pointer.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Adrian Bunk wrote:
> The Coverity checker spotted the following two array overflows in
> drivers/net/chelsio/sge.c (in both cases, the arrays contain 3
> elements):
[snip]

This is a bug. The array should contain 2 elements.  Here is the fix.
Signed-off-by: Scott Bardone <sbardone@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	return -E_NO_BIG_ENDIAN_TESTING;

[E1000]: Fix 4 missed endianness conversions on RX descriptor fields.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Merge branch 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
  powerpc: update defconfigs
  [PATCH] powerpc: properly configure DDR/P5IOC children devs
  [PATCH] powerpc: remove duplicate EXPORT_SYMBOLS
  [PATCH] powerpc: RTC memory corruption
  [PATCH] powerpc: enable NAP only on cpus who support it to avoid memory corruption
  [PATCH] powerpc: Clarify wording for CRASH_DUMP Kconfig option
  [PATCH] powerpc/64: enable CONFIG_BLK_DEV_SL82C105
  [PATCH] powerpc: correct cacheflush loop in zImage
  powerpc: Fix problem with time going backwards
  powerpc: Disallow lparcfg being a module

Signed-off-by: Paul Mackerras <paulus@samba.org>

The dynamic add path for PCI Host Bridges can fail to configure children
adapters under P5IOC controllers.  It fails to properly fixup bus/device
resources, and it fails to properly enable EEH.  Both of these steps
need to occur before any children devices are enabled in
pci_bus_add_devices().
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

remove warnings when building a 64bit kernel.
smp_call_function triggers also with 32bit kernel.

WARNING: vmlinux: duplicate symbol 'smp_call_function' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:164:EXPORT_SYMBOL(smp_call_function);
arch/powerpc/kernel/smp.c:300:EXPORT_SYMBOL(smp_call_function);

WARNING: vmlinux: duplicate symbol 'ioremap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:113:EXPORT_SYMBOL(ioremap);
arch/powerpc/mm/pgtable_64.c:321:EXPORT_SYMBOL(ioremap);

WARNING: vmlinux: duplicate symbol '__ioremap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:117:EXPORT_SYMBOL(__ioremap);
arch/powerpc/mm/pgtable_64.c:322:EXPORT_SYMBOL(__ioremap);

WARNING: vmlinux: duplicate symbol 'iounmap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:118:EXPORT_SYMBOL(iounmap);
arch/powerpc/mm/pgtable_64.c:323:EXPORT_SYMBOL(iounmap);
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

We should be memset'ing the data we are pointing to, not the pointer
itself.  This is in an error path so we probably don't hit it much.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This patch fixes incorrect setting of powersave_nap to 1 on all
PowerMacs, potentially causing memory corruption on some models. This
bug was introuced by me during the 32/64 bits merge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The wording of the CRASH_DUMP Kconfig option is not very clear. It gives you a
kernel that can be used _as_ the kdump kernel, not a kernel that can boot into
a kdump kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Enable the onboard IDE driver for p610, p615 and p630.
They have the CD connected to this card. All other RS/6000 systems with this
controller have no connectors and dont need this option.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Correct the loop for cacheflush. No idea where I copied the code from,
but the original does not work correct. Maybe the flush is not needed.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The recent changes to keep gettimeofday in sync with xtime had the side
effect that it was occasionally possible for the time reported by
gettimeofday to go back by a microsecond.  There were two reasons:
(1) when we recalculated the offsets used by gettimeofday every 2^31
timebase ticks, we lost an accumulated fractional microsecond, and
(2) because the update is done some time after the notional start of
jiffy, if ntp is slowing the clock, it is possible to see time go backwards
when the timebase factor gets reduced.

This fixes it by (a) slowing the gettimeofday clock by about 1us in
2^31 timebase ticks (a factor of less than 1 in 3.7 million), and (b)
adjusting the timebase offsets in the rare case that the gettimeofday
result could possibly go backwards (i.e. when ntp is slowing the clock
and the timer interrupt is late).  In this case the adjustment will
reduce to zero eventually because of (a).
Signed-off-by: Paul Mackerras <paulus@samba.org>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 3362/1: [cleanup] - duplicate decleration of mem_fclk_21285
  [ARM] 3365/1: [cleanup] header for compat.c exported functions
  [ARM] 3364/1: [cleanup] warning fix - definitions for enable_hlt and disable_hlt
  [ARM] 3363/1: [cleanup] process.c - fix warnings
  [ARM] 3358/1: [S3C2410] add missing SPI DMA resources
  [ARM] 3357/1: enable frontlight on collie
  [ARM] Fix "thead" typo

This fixes not one, but _two_, silly (but admittedly hard to hit) bugs
in the ext2 filesystem "readdir()" function.  It also cleans up the code
to avoid the unnecessary goto mess.

The bugs were related to re-valiating the f_pos value after somebody had
either done an "lseek()" on the directory to an invalid offset, or when
the offset had become invalid due to a file being unlinked in the
directory.  The code would not only set the f_version too eagerly, it
would also not update f_pos appropriately for when the offset fixup took
place.

When that happened, we'd occasionally subsequently fail the readdir()
even when we shouldn't (no real harm done, but an ugly printk, and
obviously you would end up not necessarily seeing all entries).

Thanks to Masoud Sharbiani <masouds@google.com> who noticed the problem
and had a test-case for it, and also fixed up a thinko in the first
version of this patch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Masoud Sharbiani <masouds@google.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Patch from Ben Dooks

arch/arm/kernel/setup.c declares mem_fclk_21285 when
this is already declared in include/asm-arm/system.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

arch/arm/kernel/compat.c exports two functions,
convert_to_tag_list and squash_mem_tags which
are not defined in any header files, and not
used outside arch/arm/kernel.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The enable_hlt and disable_hlt should be declared in
include/asm/setup.h. This fixes sparse errors from
arch/arm/kernel/process.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Fix the following warnings from sparse:

arch/arm/kernel/process.c:86:6: warning: symbol 'default_idle' was not declared. Should it be static?
arch/arm/kernel/process.c:378:5: warning: symbol 'dump_fpu' was not declared.   Should it be static?

Include <linux/elfcore.h> for dump_fpu() decleration, and
make default_idle() static as it is not used outside the file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix QoS is not active even the network and the card is QOS enabled.
The problem is we pass the wrong ieee80211_network address to
ipw_handle_beacon/ipw_handle_probe_response, thus the
ieee80211_network->qos_data.active will not be set, causing the driver
not sending QoS frames at all.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the correct STYPE for Qos data.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Olaf Hering reported a problem on pseries with e100 where ethtool -t would
cause a bus error, and the e100 driver would stop working.  Due to the new
load ucode command the cb list must be allocated before calling
e100_init_hw, so remove the call and just let e100_up take care of it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>

The Coverity checker spotted the following bug in dup_namespace():

<--  snip  -->

        if (!new_ns->root) {
                up_write(&namespace_sem);
                kfree(new_ns);
                goto out;
        }
...
out:
        return new_ns;

<--  snip  -->

Callers expect a non-NULL result to not be freed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Patch from Albrecht Dre

Add DMA resources to s3c2410 spi platform devices - dma_(alloc|free)_coherent should now work as expected.
Signed-off-by: Albrecht Dre <albrecht.dress@lios-tech.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Pavel Machek

Enable frontlight during collie bootup, so that display is actually
readable in anything other than bright sunlight.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

It seems that setting scheduling policy and priorities is also the kind of
thing that might be performed in apps that also use the NUMA API, so it
would seem consistent to use CAP_SYS_NICE for NUMA also.

So use CAP_SYS_NICE for controlling migration permissions.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Update the documentation for page migration.

- Fix up bits and pieces in cpusets.txt

- Rework text in vm/page-migration to be clearer and reflect the final
  version of page migration in 2.6.16. Mention Andi Kleen's numactl
  package that contains user space tools for page migration via
  libnuma. Add reference to numa_maps and to the manpage in numactl.

- Add todo list for outstanding issues
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

page migration currently simply retries a couple of times if try_to_unmap()
fails without inspecting the return code.

However, SWAP_FAIL indicates that the page is in a vma that has the
VM_LOCKED flag set (if ignore_refs ==1).  We can check for that return code
and avoid retrying the migration.

migrate_page_remove_references() now needs to return a reason why the
failure occured.  So switch migrate_page_remove_references to use -Exx
style error messages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

It seems this patch got dropped (it was in addition to the `s390:
improve response code handling in chsc_enable_facility()' patch).
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* git://oss.sgi.com:8090/oss/git/rc-fixes:
  Fix a direct I/O locking issue revealed by the new mutex code.

Affects only XFS (i.e. DIO_OWN_LOCKING case) - currently it is
not possible to get i_mutex locking correct when using DIO_OWN
direct I/O locking in a filesystem due to indeterminism in the
possible return code/lock/unlock combinations.  This can cause
a direct read to attempt a double i_mutex unlock inside XFS.

We're now ensuring __blockdev_direct_IO always exits with the
inode i_mutex (still) held for a direct reader.

Tested with the three different locking modes (via direct block
device access, ext3 and XFS) - both reading and writing; cannot
find any regressions resulting from this change, and it clearly
fixes the mutex_unlock warning originally reported here:
http://marc.theaimsgroup.com/?l=linux-kernel&m=114189068126253&w=2Signed-off-by: Nathan Scott <nathans@sgi.com>
Acked-by: Christoph Hellwig <hch@lst.de>

This fixes a race where lsn could be cleared before taking the lock
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] zfcp: fix device registration issues
  [SCSI] scsi_transport_fc: fix FC_HOST_NUM_ATTRS
  [SCSI] scsi: aha152x pcmcia driver needs spi transport
  [SCSI] zfcp: correctly set this_id for hosts
  [SCSI] Add Brownie to blacklist

lapic_shutdown() re-enables interrupts which is un-desirable for panic
case, so use local_irq_save() and local_irq_restore() to keep the irqs
disabled for kexec on panic case, and close a possible race window while
kdump shutdown as shown in this stack trace

   -- BUG: spinlock lockup on CPU#1, bash/4396, c52781a0
   [<c01c1870>] _raw_spin_lock+0xb7/0xd2
   [<c029e148>] _spin_lock+0x6/0x8
   [<c011b33f>] scheduler_tick+0xe7/0x328
   [<c0128a7c>] update_process_times+0x51/0x5d
   [<c0114592>] smp_apic_timer_interrupt+0x4f/0x58
   [<c01141ff>] lapic_shutdown+0x76/0x7e
   [<c0104d7c>] apic_timer_interrupt+0x1c/0x30
   [<c01141ff>] lapic_shutdown+0x76/0x7e
   [<c0116659>] machine_crash_shutdown+0x83/0xaa
   [<c013cc36>] crash_kexec+0xc1/0xe3
   [<c029e148>] _spin_lock+0x6/0x8
   [<c013cc22>] crash_kexec+0xad/0xe3
   [<c0215280>] __handle_sysrq+0x84/0xfd
   [<c018d937>] write_sysrq_trigger+0x2c/0x35
   [<c015e47b>] vfs_write+0xa2/0x13b
   [<c015ea73>] sys_write+0x3b/0x64
   [<c0103c69>] syscall_call+0x7/0xb
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This reverts commit c33d4568.

Andrew Clayton and Hugh Dickins report that it's broken for them and
causes strange page table and slab corruption, and spontaneous reboots.

Let's get it right next time.

Cc: Andrew Clayton <andrew@rootshell.co.uk>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

- Disable the EDAC sysfs code.  The sysfs interface that EDAC presents to
  user space needs more thought, and is likely to change substantially.
  Therefore disable it for now so users don't start depending on it in its
  current form.

- Disable the default behavior of calling panic() when an uncorrectible
  error is detected (since for now, there is no sysfs interface that allows
  the user to configure this behavior).
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

In theory, NLM specs assure us that the server will only reply LCK_GRANTED or
LCK_DENIED_GRACE_PERIOD to our NLM_UNLOCK request.

In practice, we should not assume this to be the case, and the code will
currently Oops if we do.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>