Merge tag 'omap-for-v4.2/fixes-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps, all dts changes except for one:

- Fix up LCD panel name for overo boards

- Three fixes for pepper board for regulators, freqeuncy
  scaling and audio input. Note that there is still one
  issue being worked on for booting with multi_v7_defconfig

- Add missing #iommu-cells for omap4 and 5

- Add missing HAVE_ARM_SCU for am43xx

* tag 'omap-for-v4.2/fixes-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (210 commits)
  ARM: dts: Correct audio input route & set mic bias for am335x-pepper
  ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
  ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
  ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
  ARM: dts: Fix frequency scaling on Gumstix Pepper
  ARM: dts: configure regulators for Gumstix Pepper
  ARM: dts: omap3: overo: Update LCD panel names
  + Linux 4.2-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>

Audio-in was incorrectly routed to Line In. It should be Mic3L as per
schematic.

Using mic-bias voltage at 2.0v (<0x1>) does not work for some reason. There
is no voltage seen on micbias (R127). Mic-bias voltage of 2.5v (<0x2>) works.
I see voltage of 2.475v across GND and micbias.

With these changes, I can record audio with a pair of proliferate TRRS earbuds.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Acked-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

CONFIG_HAVE_ARM_SCU only gets selected if CONFIG_SMP is selected in an OMAP
system, however AM43XX needs this option regardless of CONFIG_SMP and also
for an AM43XX only build as it is important for controlling power in the SoC.
Without this we cannot suspend the CPU for SoC suspend or cpuidle. The
ARM Cortex A9 needs SCU CPU Power Status bits to be set to off mode in order
for the PRCM to transition the MPU to low power modes.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'imx-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: imx: fixes for 4.2" from Shawn Guo:

The i.MX fixes for 4.2:
 - Correct compatible string for i.MX27 GPT which actually shares the
   same programming model as i.MX21 GPT rather than i.MX1 one.
 - Add missing #io-channel-cells property for i.MX23 LRADC device, which
   is required for the device to be an IIO provider.
 - Correct HSYNC/VSYNC pins and add ddc-i2c-bus property for TVE device
   on imx53-qsb to work properly.
 - Always enable PU domain if CONFIG_PM is not set.  This fixes a couple
   of failure scenarios which will hang the system if one of the devices
   in the PU domain is accessed.

* tag 'imx-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
  ARM: dts: imx53-qsb: fix TVE entry
  ARM: dts: mx23: fix iio-hwmon support
  ARM: dts: imx27: Adjust the GPT compatible string
Signed-off-by: Olof Johansson <olof@lixom.net>

The 'digicolor' regexp doesn't cover the dts files. Add a glob pattern for
them.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'socfpga_fixes_for_v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into fixes

Merge "SoCFPGA fixes for v4.2-rc1" from Dinh Nguyen:

SoCFPGA fixes against v4.2-rc1
- Update compatible "adxl345x" compatible string
- Alphabetize the DTS nodes for the C5 sockit board file

* tag 'socfpga_fixes_for_v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: socfpga: dts: Fix entries order
  ARM: socfpga: dts: Fix adxl34x formating and compatible string

Ux500 is regressing due to commit
a21763a0
"pinctrl: nomadik: activate strict mux mode" which disallows
Nomadik GPIO 5 to be muxed in as a level shifter voltage select
pin, as it is currently described as being used for RX on UART1.

The behaviour is correct, instead the hardware config has been
incorrecly specified: UART1 is indeed unused on HREFv60plus and
Snowball and that is why HREFv60plus can use the pins it would
normally occupy as the voltage select line for the MMC/SD
levelshifter (Snowball uses it for I2C4).

The reason UART1 was anyway enabled on these platforms was
probably to secure the port enumeration to userspace. This
can be solved by using aliases (done in a separate patch) so
we can now deactivate UART1 and let MMC/SD use it properly
on HREFv60plus. We explicitly activate it only for the
older HREFprev60 board.

To complete, we set up the pin configuration for these pins
properly in the sdi0 node.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This enumerates the PL011 serial ports on the Ux500. This is
necessary to do if we want to remove one of the serial ports,
since userspace depends on console to be present on ttyAMA2
and we must not break userspace.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP5 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP4 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The device tree for Gumstix Pepper has DCDC2 and
DCDC3 correctly labelled but the upper limit values
are wrong. The confusion is due to the hardware
quirk where the DCDC2 and DCDC3 wires are flipped
in Pepper.
Signed-off-by: Arun Bharadwaj <arun@gumstix.com>
Tested-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Boot process is halting in midway because some of the necessary voltage
regulators are deemed unused and subsequently powered off, leading to
a completely unresponsive system.

Most of the device nodes had correct voltage regulator attachments.
Yet these nodes had to set stricter enforcement on them through
'regulator-boot-on' and 'regulator-always-on' to function correctly.

The consumers of the regulators this commit affect are the followings:

	DCDC1: vdd_1v8 system supply, USB-PHY, and ADC
	DCDC2: Core domain
	DCDC3: MPU core domain
	 LDO1: RTC
	 LDO2: 3v3 IO domain
	 LDO3: USB-PHY; not a boot-time requirement
	 LDO4: LCD [16:23]

All but LDO3 need to be always-on for the system to be functional.

Additionally regulator-name properties have been added for the kernel to
display the name from the schematic. This will improve diagnostics.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For Gumstix Overo COMs, the u-boot bootloader typically passes an
argument specifying the default display via the omapdss.def_disp
parameter.  When a default display is specified, DSS2 tries to match
this name with either the device tree label (e.g. label=dvi) or,
failing this, the device tree alias (e.g. label=display0). Update the
panel names for the 'lcd43' and 'lcd35' displays in the device tree
such that they match the names passed by u-boot.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for 4 Japanese keys
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This reverts commit dec4f799.

Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:

        crtc_state = state->base.state ?
                intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;

So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.

There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull VFS fixes from Al Viro:
 "Fixes for this cycle regression in overlayfs and a couple of
  long-standing (== all the way back to 2.6.12, at least) bugs"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  freeing unlinked file indefinitely delayed
  fix a braino in ovl_d_select_inode()
  9p: don't leave a half-initialized inode sitting around

Pull MIPS fixes from Ralf Baechle:
 "A fair number of 4.2 fixes also because Markos opened the flood gates.

   - Patch up the math used calculate the location for the page bitmap.

   - The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
     around was causing issues on non-Malta platforms, so move the code
     to a Malta specific location.

   - A spelling fix replicated through several files.

   - Fix to the emulation of an R2 instruction for R6 cores.

   - Fix the JR emulation for R6.

   - Further patching of mindless 64 bit issues.

   - Ensure the kernel won't crash on CPUs with L2 caches with >= 8
     ways.

   - Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.

   - Fix cache flushing for multithreaded cores.

   - A build fix"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: O32: Use compat_sys_getsockopt.
  MIPS: c-r4k: Extend way_string array
  MIPS: Pistachio: Support CDMM & Fast Debug Channel
  MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
  MIPS: c-r4k: Fix cache flushing for MT cores
  Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
  MIPS: cps-vec: Use macros for various arithmetics and memory operations
  MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
  MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
  MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
  MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
  MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
  MIPS: Fix erroneous JR emulation for MIPS R6
  MIPS: Fix branch emulation for BLTC and BGEC instructions
  MIPS: kernel: traps: Fix broken indentation
  MIPS: bootmem: Don't use memory holes for page bitmap
  MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
  MIPS, CPUFREQ: Fix spelling of Institute.
  MIPS: Lemote 2F: Fix build caused by recent mass rename.

Pull x86 fixes from Thomas Gleixner:

 - the high latency PIT detection fix, which slipped through the cracks
   for rc1

 - a regression fix for the early printk mechanism

 - the x86 part to plug irq/vector related hotplug races

 - move the allocation of the espfix pages on cpu hotplug to non atomic
   context.  The current code triggers a might_sleep() warning.

 - a series of KASAN fixes addressing boot crashes and usability

 - a trivial typo fix for Kconfig help text

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
  x86/irq: Retrieve irq data after locking irq_desc
  x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
  x86/irq: Plug irq vector hotplug race
  x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
  x86/espfix: Init espfix on the boot CPU side
  x86/espfix: Add 'cpu' parameter to init_espfix_ap()
  x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
  x86/kasan: Add message about KASAN being initialized
  x86/kasan: Fix boot crash on AMD processors
  x86/kasan: Flush TLBs after switching CR3
  x86/kasan: Fix KASAN shadow region page tables
  x86/init: Clear 'init_level4_pgt' earlier
  x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()

Pull timer fixes from Thomas Gleixner:
 "This update from the timer departement contains:

   - A series of patches which address a shortcoming in the tick
     broadcast code.

     If the broadcast device is not available or an hrtimer emulated
     broadcast device, some of the original assumptions lead to boot
     failures.  I rather plugged all of the corner cases instead of only
     addressing the issue reported, so the change got a little larger.

     Has been extensivly tested on x86 and arm.

   - Get rid of the last holdouts using do_posix_clock_monotonic_gettime()

   - A regression fix for the imx clocksource driver

   - An update to the new state callbacks mechanism for clockevents.
     This is required to simplify the conversion, which will take place
     in 4.3"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/broadcast: Prevent NULL pointer dereference
  time: Get rid of do_posix_clock_monotonic_gettime
  cris: Replace do_posix_clock_monotonic_gettime()
  tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
  tick/broadcast: Handle spurious interrupts gracefully
  tick/broadcast: Check for hrtimer broadcast active early
  tick/broadcast: Return busy when IPI is pending
  tick/broadcast: Return busy if periodic mode and hrtimer broadcast
  tick/broadcast: Move the check for periodic mode inside state handling
  tick/broadcast: Prevent deep idle if no broadcast device available
  tick/broadcast: Make idle check independent from mode and config
  tick/broadcast: Sanity check the shutdown of the local clock_event
  tick/broadcast: Prevent hrtimer recursion
  clockevents: Allow set-state callbacks to be optional
  clocksource/imx: Define clocksource for mx27

Pull irq fix from Thomas Gleixner:
 "A single fix for a cpu hotplug race vs. interrupt descriptors:

  Prevent irq setup/teardown across the cpu starting/dying parts of cpu
  hotplug so that the starting/dying cpu has a stable view of the
  descriptor space.  This has been an issue for all architectures in the
  cpu dying phase, where interrupts are migrated away from the dying
  cpu.  In the starting phase its mostly a x86 issue vs the vector space
  update"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hotplug: Prevent alloc/free of irq descriptors during cpu up/down

	Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course).  However, there's one case where that
does *not* happen.  Namely, if you open it by fhandle with cold dcache,
then unlink() and close().

	In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal.  In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()).  The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in.  As the result, we have the final iput() delayed
indefinitely.  It's trivial to reproduce -

void flush_dcache(void)
{
        system("mount -o remount,rw /");
}

static char buf[20 * 1024 * 1024];

main()
{
        int fd;
        union {
                struct file_handle f;
                char buf[MAX_HANDLE_SZ];
        } x;
        int m;

        x.f.handle_bytes = sizeof(x);
        chdir("/root");
        mkdir("foo", 0700);
        fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
        close(fd);
        name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
        flush_dcache();
        fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
        unlink("foo/bar");
        write(fd, buf, sizeof(buf));
        system("df .");			/* 20Mb eaten */
        close(fd);
        system("df .");			/* should've freed those 20Mb */
        flush_dcache();
        system("df .");			/* should be the same as #2 */
}

will spit out something like
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 283282     21692  93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).

Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Cc: stable@vger.kernel.org # all branches
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull libnvdimm fixes from Dan Williams:
 "1) Fixes for a handful of smatch reports (Thanks Dan C.!) and minor
     bug fixes (patches 1-6)

  2) Correctness fixes to the BLK-mode nvdimm driver (patches 7-10).

     Granted these are slightly large for a -rc update.  They have been
     out for review in one form or another since the end of May and were
     deferred from the merge window while we settled on the "PMEM API"
     for the PMEM-mode nvdimm driver (ie memremap_pmem, memcpy_to_pmem,
     and wmb_pmem).

     Now that those apis are merged we implement them in the BLK driver
     to guarantee that mmio aperture moves stay ordered with respect to
     incoming read/write requests, and that writes are flushed through
     those mmio-windows and platform-buffers to be persistent on media.

  These pass the sub-system unit tests with the updates to
  tools/testing/nvdimm, and have received a successful build-report from
  the kbuild robot (468 configs).

  With acks from Rafael for the touches to drivers/acpi/"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
  nfit: add support for NVDIMM "latch" flag
  nfit: update block I/O path to use PMEM API
  tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
  tools/testing/nvdimm: fix return code for unimplemented commands
  tools/testing/nvdimm: mock ioremap_wt
  pmem: add maintainer for include/linux/pmem.h
  nfit: fix smatch "use after null check" report
  nvdimm: Fix return value of nvdimm_bus_init() if class_create() fails
  libnvdimm: smatch cleanups in __nd_ioctl
  sparse: fix misplaced __pmem definition

Pull i2c fixes from Wolfram Sang:
 "Mostly slight adjusments for new drivers, but also one core fix for
  which finally the dependencies are now available as well"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: Mark instantiated device nodes with OF_POPULATE
  i2c: jz4780: Fix return value if probe fails
  i2c: xgene-slimpro: Fix missing mbox_free_channel call in probe error path
  i2c: I2C_MT65XX should depend on HAS_DMA

Pull input fixes from Dmitry Torokhov:
 "A fix (revert) for a recent regression in Synaptics driver and a fix
  for Elan i2c touchpad driver"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
  Input: elan_i2c - change the hover event from MT to ST

Pull clk fixes from Stephen Boyd:
 "A small set of fixes for problems found by smatch in new drivers that
  we added this rc and a handful of driver fixes that came in during the
  merge window"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  drivers: clk: st: Incorrect register offset used for lock_status
  clk: mediatek: mt8173: Fix enabling of critical clocks
  drivers: clk: st: Fix mux bit-setting for Cortex A9 clocks
  drivers: clk: st: Add CLK_GET_RATE_NOCACHE flag to clocks
  drivers: clk: st: Fix flexgen lock init
  drivers: clk: st: Fix FSYN channel values
  drivers: clk: st: Remove unused code
  clk: qcom: Use parent rate when set rate to pixel RCG clock
  clk: at91: do not leak resources
  clk: stm32: Fix out-by-one error path in the index lookup
  clk: iproc: fix bit manipulation arithmetic
  clk: iproc: fix memory leak from clock name

Pull drm fixes from Dave Airlie:
 "A bunch of fixes for radeon, intel, omap and one amdkfd fix.

  Radeon fixes are all over, but it does fix some cursor corruption
  across suspend/resume.  i915 should fix the second warn you were
  seeing, so let us know if not.  omap is a bunch of small fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
  drm/radeon: disable vce init on cayman (v2)
  drm/amdgpu: fix timeout calculation
  drm/radeon: check if BO_VA is set before adding it to the invalidation list
  drm/radeon: allways add the VM clear duplicate
  Revert "Revert "drm/radeon: dont switch vt on suspend""
  drm/radeon: Fold radeon_set_cursor() into radeon_show_cursor()
  drm/radeon: unpin cursor BOs on suspend and pin them again on resume (v2)
  drm/radeon: Clean up reference counting and pinning of the cursor BOs
  drm/amdkfd: validate pdd where it acquired first
  Revert "drm/i915: Allocate context objects from stolen"
  drm/i915: Declare the swizzling unknown for L-shaped configurations
  drm/radeon: fix underflow in r600_cp_dispatch_texture()
  drm/radeon: default to 2048 MB GART size on SI+
  drm/radeon: fix HDP flushing
  drm/radeon: use RCU query for GEM_BUSY syscall
  drm/amdgpu: Handle irqs only based on irq ring, not irq status regs.
  drm/radeon: Handle irqs only based on irq ring, not irq status regs.
  drm/i915: Use crtc_state->active in primary check_plane func
  drm/i915: Check crtc->active in intel_crtc_disable_planes
  drm/i915: Restore all GGTT VMAs on resume
  ...

Pull selinux fixes from James Morris.

* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selinux: fix mprotect PROT_EXEC regression caused by mm change
  selinux: don't waste ebitmap space when importing NetLabel categories

Pull btrfs fixes from Chris Mason:
 "This is an assortment of fixes.  Most of the commits are from Filipe
  (fsync, the inode allocation cache and a few others).  Mark kicked in
  a series fixing corners in the extent sharing ioctls, and everyone
  else fixed up on assorted other problems"

* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix wrong check for btrfs_force_chunk_alloc()
  Btrfs: fix warning of bytes_may_use
  Btrfs: fix hang when failing to submit bio of directIO
  Btrfs: fix a comment in inode.c:evict_inode_truncate_pages()
  Btrfs: fix memory corruption on failure to submit bio for direct IO
  btrfs: don't update mtime/ctime on deduped inodes
  btrfs: allow dedupe of same inode
  btrfs: fix deadlock with extent-same and readpage
  btrfs: pass unaligned length to btrfs_cmp_data()
  Btrfs: fix fsync after truncate when no_holes feature is enabled
  Btrfs: fix fsync xattr loss in the fast fsync path
  Btrfs: fix fsync data loss after append write
  Btrfs: fix crash on close_ctree() if cleaner starts new transaction
  Btrfs: fix race between caching kthread and returning inode to inode cache
  Btrfs: use kmem_cache_free when freeing entry in inode cache
  Btrfs: fix race between balance and unused block group deletion
  btrfs: add error handling for scrub_workers_get()
  btrfs: cleanup noused initialization of dev in btrfs_end_bio()
  btrfs: qgroup: allow user to clear the limitation on qgroup

Pull ARM SoC fixes from Kevin Hilman:
 "A fairly random colletion of fixes based on -rc1 for OMAP, sunxi and
  prima2 as well as a few arm64-specific DT fixes.

  This series also includes a late to support a new Allwinner (sunxi)
  SoC, but since it's rather simple and isolated to the
  platform-specific code, it's included it for this -rc"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: add device tree for ARM SMM-A53x2 on LogicTile Express 20MG
  arm: dts: vexpress: add missing CCI PMU device node to TC2
  arm: dts: vexpress: describe all PMUs in TC2 dts
  GICv3: Add ITS entry to THUNDER dts
  arm64: dts: Add poweroff button device node for APM X-Gene platform
  ARM: dts: am4372.dtsi: disable rfbi
  ARM: dts: am57xx-beagle-x15: Provide supply for usb2_phy2
  ARM: dts: am4372: Add emif node
  Revert "ARM: dts: am335x-boneblack: disable RTC-only sleep"
  ARM: sunxi: Enable simplefb in the defconfig
  ARM: Remove deprecated symbol from defconfig files
  ARM: sunxi: Add Machine support for A33
  ARM: sunxi: Introduce Allwinner H3 support
  Documentation: sunxi: Update Allwinner SoC documentation
  ARM: prima2: move to use REGMAP APIs for rtciobrg
  ARM: dts: atlas7: add pinctrl and gpio descriptions
  ARM: OMAP2+: Remove unnessary return statement from the void function, omap2_show_dma_caps
  memory: omap-gpmc: Fix parsing of devices

Dan reported that the recent changes to the broadcast code introduced
a potential NULL dereference.

Add the proper check.

Fixes: e0454311 "tick/broadcast: Sanity check the shutdown of the local clock_event"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull parisc fixes from Helge Deller:
 "We have one important patch from Dave Anglin and myself which fixes
  PTE/TLB race conditions which caused random segmentation faults on our
  debian buildd servers, and one patch from Alex Ivanov which speeds up
  the graphical text console on the STI framebuffer driver"

* 'parisc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix some PTE/TLB race conditions and optimize __flush_tlb_range based on timing results
  stifb: Implement hardware accelerated copyarea

commit 66fc1303 ("mm: shmem_zero_setup
skip security check and lockdep conflict with XFS") caused a regression
for SELinux by disabling any SELinux checking of mprotect PROT_EXEC on
shared anonymous mappings.  However, even before that regression, the
checking on such mprotect PROT_EXEC calls was inconsistent with the
checking on a mmap PROT_EXEC call for a shared anonymous mapping.  On a
mmap, the security hook is passed a NULL file and knows it is dealing
with an anonymous mapping and therefore applies an execmem check and no
file checks.  On a mprotect, the security hook is passed a vma with a
non-NULL vm_file (as this was set from the internally-created shmem
file during mmap) and therefore applies the file-based execute check
and no execmem check.  Since the aforementioned commit now marks the
shmem zero inode with the S_PRIVATE flag, the file checks are disabled
and we have no checking at all on mprotect PROT_EXEC.  Add a test to
the mprotect hook logic for such private inodes, and apply an execmem
check in that case.  This makes the mmap and mprotect checking
consistent for shared anonymous mappings, as well as for /dev/zero and
ashmem.

Cc: <stable@vger.kernel.org> # 4.1.x
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <pmoore@redhat.com>

Pull arm64 fixes and clean-up from Catalin Marinas:
 - ACPI fix when checking the validity of the GICC MADT subtable
 - handle debug exceptions in the el*_inv exception entries
 - remove pointless register assignment in two compat syscall wrappers
 - unnecessary include path
 - defconfig update

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: entry32: remove pointless register assignment
  arm64: entry: handle debug exceptions in el*_inv
  arm64: Keep the ARM64 Kconfig selects sorted
  ACPI / ARM64 : use the new BAD_MADT_GICC_ENTRY macro
  ACPI / ARM64: add BAD_MADT_GICC_ENTRY() macro
  arm64: defconfig: Add Ceva ahci to the defconfig
  arm64: remove another unnecessary libfdt include path

The increased use of pdtlb/pitlb instructions seemed to increase the
frequency of random segmentation faults building packages. Further, we
had a number of cases where TLB inserts would repeatedly fail and all
forward progress would stop. The Haskell ghc package caused a lot of
trouble in this area. The final indication of a race in pte handling was
this syslog entry on sibaris (C8000):

 swap_free: Unused swap offset entry 00000004
 BUG: Bad page map in process mysqld  pte:00000100 pmd:019bbec5
 addr:00000000ec464000 vm_flags:00100073 anon_vma:0000000221023828 mapping: (null) index:ec464
 CPU: 1 PID: 9176 Comm: mysqld Not tainted 4.0.0-2-parisc64-smp #1 Debian 4.0.5-1
 Backtrace:
  [<0000000040173eb0>] show_stack+0x20/0x38
  [<0000000040444424>] dump_stack+0x9c/0x110
  [<00000000402a0d38>] print_bad_pte+0x1a8/0x278
  [<00000000402a28b8>] unmap_single_vma+0x3d8/0x770
  [<00000000402a4090>] zap_page_range+0xf0/0x198
  [<00000000402ba2a4>] SyS_madvise+0x404/0x8c0

Note that the pte value is 0 except for the accessed bit 0x100. This bit
shouldn't be set without the present bit.

It should be noted that the madvise system call is probably a trigger for many
of the random segmentation faults.

In looking at the kernel code, I found the following problems:

1) The pte_clear define didn't take TLB lock when clearing a pte.
2) We didn't test pte present bit inside lock in exception support.
3) The pte and tlb locks needed to merged in order to ensure consistency
between page table and TLB. This also has the effect of serializing TLB
broadcasts on SMP systems.

The attached change implements the above and a few other tweaks to try
to improve performance. Based on the timing code, TLB purges are very
slow (e.g., ~ 209 cycles per page on rp3440). Thus, I think it
beneficial to test the split_tlb variable to avoid duplicate purges.
Probably, all PA 2.0 machines have combined TLBs.

I dropped using __flush_tlb_range in flush_tlb_mm as I realized all
applications and most threads have a stack size that is too large to
make this useful. I added some comments to this effect.

Since implementing 1 through 3, I haven't had any random segmentation
faults on mx3210 (rp3440) in about one week of building code and running
as a Debian buildd.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Helge Deller <deller@gmx.de>

This patch adds hardware assisted scrolling. The code is based upon the
following investigation: https://parisc.wiki.kernel.org/index.php/NGLE#Blitter

A simple 'time ls -la /usr/bin' test shows 1.6x speed increase over soft
copy and 2.3x increase over FBINFO_READS_FAST (prefer soft copy over
screen redraw) on Artist framebuffer.
Signed-off-by: Alex Ivanov <lausgans@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>

Pull powerpc fixes from Michael Ellerman:
 - opal-prd mmap fix from Vaidy
 - set kernel taint for MCEs from Daniel
 - alignment exception description from Anton
 - ppc4xx_hsta_msi build fix from Daniel
 - opal-elog interrupt fix from Alistair
 - core_idle_state race fix from Shreyas
 - hv-24x7 lockdep fix from Sukadev
 - multiple cxl fixes from Daniel, Ian, Mikey & Maninder
 - update MAINTAINERS to point at shared tree

* tag 'powerpc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  cxl: Check if afu is not null in cxl_slbia
  powerpc: Update MAINTAINERS to point at shared tree
  powerpc/perf/24x7: Fix lockdep warning
  cxl: Fix off by one error allowing subsequent mmap page to be accessed
  cxl: Fail mmap if requested mapping is larger than assigned problem state area
  cxl: Fix refcounting in kernel API
  powerpc/powernv: Fix race in updating core_idle_state
  powerpc/powernv: Fix opal-elog interrupt handler
  powerpc/ppc4xx_hsta_msi: Include ppc-pci.h to fix reference to hose_list
  powerpc: Add plain English description for alignment exception oopses
  cxl: Test the correct mmio space before unmapping
  powerpc: Set the correct kernel taint on machine check errors
  cxl/vphb.c: Use phb pointer after NULL check
  powerpc/powernv: Fix vma page prot flags in opal-prd driver