Commit 2abb0d52 ("PM / devfreq: Lock devfreq in trans_stat_show")
revealed a missing locking while calling devfreq_update_status() function
during suspend/resume cycle.

Code analysis revealed that devfreq_set_target() function was called
without needed locks held for setting device specific suspend_freq if such
has been defined. This patch fixes that by adding the needed locking, what
fixes following kernel warning on Exynos4412-based OdroidU3 board during
system suspend:

PM: suspend entry (deep)
Filesystems sync: 0.002 seconds
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1385 at drivers/devfreq/devfreq.c:204 devfreq_update_status+0xc0/0x188
Modules linked in:
CPU: 2 PID: 1385 Comm: rtcwake Not tainted 5.4.0-rc6-next-20191111 #6848
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0112588>] (unwind_backtrace) from [<c010e070>] (show_stack+0x10/0x14)
[<c010e070>] (show_stack) from [<c0afb010>] (dump_stack+0xb4/0xe0)
[<c0afb010>] (dump_stack) from [<c01272e0>] (__warn+0xf4/0x10c)
[<c01272e0>] (__warn) from [<c01273a8>] (warn_slowpath_fmt+0xb0/0xb8)
[<c01273a8>] (warn_slowpath_fmt) from [<c07d105c>] (devfreq_update_status+0xc0/0x188)
[<c07d105c>] (devfreq_update_status) from [<c07d2d70>] (devfreq_set_target+0xb0/0x15c)
[<c07d2d70>] (devfreq_set_target) from [<c07d3598>] (devfreq_suspend+0x2c/0x64)
[<c07d3598>] (devfreq_suspend) from [<c05de0b0>] (dpm_suspend+0xa4/0x57c)
[<c05de0b0>] (dpm_suspend) from [<c05def74>] (dpm_suspend_start+0x98/0xa0)
[<c05def74>] (dpm_suspend_start) from [<c0195b58>] (suspend_devices_and_enter+0xec/0xc74)
[<c0195b58>] (suspend_devices_and_enter) from [<c0196a20>] (pm_suspend+0x340/0x410)
[<c0196a20>] (pm_suspend) from [<c019480c>] (state_store+0x6c/0xc8)
[<c019480c>] (state_store) from [<c033fc50>] (kernfs_fop_write+0x10c/0x228)
[<c033fc50>] (kernfs_fop_write) from [<c02a6d3c>] (__vfs_write+0x30/0x1d0)
[<c02a6d3c>] (__vfs_write) from [<c02a9afc>] (vfs_write+0xa4/0x180)
[<c02a9afc>] (vfs_write) from [<c02a9d58>] (ksys_write+0x60/0xd8)
[<c02a9d58>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed3d7fa8 to 0xed3d7ff0)
...
irq event stamp: 9667
hardirqs last  enabled at (9679): [<c0b1e7c4>] _raw_spin_unlock_irq+0x20/0x58
hardirqs last disabled at (9698): [<c0b16a20>] __schedule+0xd8/0x818
softirqs last  enabled at (9694): [<c01026fc>] __do_softirq+0x4fc/0x5fc
softirqs last disabled at (9719): [<c012fe68>] irq_exit+0x16c/0x170
---[ end trace 41ac5b57d046bdbc ]---
------------[ cut here ]------------
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull power management updates from Rafael Wysocki:
 "These include cpuidle changes to use nanoseconds (instead of
  microseconds) as the unit of time and to simplify checks for disabled
  idle states in the idle loop, some cpuidle fixes and governor updates,
  assorted cpufreq updates (driver updates mostly and a few core fixes
  and cleanups), devfreq updates (dominated by the tegra30 driver
  changes), new CPU IDs for the RAPL power capping driver, relatively
  minor updates of the generic power domains (genpd) and operation
  performance points (OPP) frameworks, and assorted fixes and cleanups.

  There are also two maintainer information updates: Chanwoo Choi will
  be maintaining the devfreq subsystem going forward and Todd Brandt is
  going to maintain the pm-graph utility (created by him).

  Specifics:

   - Use nanoseconds (instead of microseconds) as the unit of time in
     the cpuidle core and simplify checks for disabled idle states in
     the idle loop (Rafael Wysocki)

   - Fix and clean up the teo cpuidle governor (Rafael Wysocki)

   - Fix the cpuidle registration error code path (Zhenzhong Duan)

   - Avoid excessive vmexits in the ACPI cpuidle driver (Yin Fengwei)

   - Extend the idle injection infrastructure to be able to measure the
     requested duration in nanoseconds and to allow an exit latency
     limit for idle states to be specified (Daniel Lezcano)

   - Fix cpufreq driver registration and clarify a comment in the
     cpufreq core (Viresh Kumar)

   - Add NULL checks to the show() and store() methods of sysfs
     attributes exposed by cpufreq (Kai Shen)

   - Update cpufreq drivers:
      * Fix for a plain int as pointer warning from sparse in
        intel_pstate (Jamal Shareef)
      * Fix for a hardcoded number of CPUs and stack bloat in the
        powernv driver (John Hubbard)
      * Updates to the ti-cpufreq driver and DT files to support new
        platforms and migrate bindings from opp-v1 to opp-v2 (Adam Ford,
        H. Nikolaus Schaller)
      * Merging of the arm_big_little and vexpress-spc drivers and
        related cleanup (Sudeep Holla)
      * Fix for imx's default speed grade value (Anson Huang)
      * Minor cleanup of the s3c64xx driver (Nathan Chancellor)
      * CPU speed bin detection fix for sun50i (Ondrej Jirman)

   - Appoint Chanwoo Choi as the new devfreq maintainer.

   - Update the devfreq core:
      * Check NULL governor in available_governors_show sysfs to prevent
        showing wrong governor information and fix a race condition
        between devfreq_update_status() and trans_stat_show() (Leonard
        Crestez)
      * Add new 'interrupt-driven' flag for devfreq governors to allow
        interrupt-driven governors to prevent the devfreq core from
        polling devices for status (Dmitry Osipenko)
      * Improve an error message in devfreq_add_device() (Matthias
        Kaehlcke)

   - Update devfreq drivers:
      * tegra30 driver fixes and cleanups (Dmitry Osipenko)
      * Removal of unused property from dt-binding documentation for the
        exynos-bus driver (Kamil Konieczny)
      * exynos-ppmu cleanup and DT bindings update (Lukasz Luba, Marek
        Szyprowski)

   - Add new CPU IDs for CometLake Mobile and Desktop to the Intel RAPL
     power capping driver (Zhang Rui)

   - Allow device initialization in the generic power domains (genpd)
     framework to be more straightforward and clean it up (Ulf Hansson)

   - Add support for adjusting OPP voltages at run time to the OPP
     framework (Stephen Boyd)

   - Avoid freeing memory that has never been allocated in the
     hibernation core (Andy Whitcroft)

   - Clean up function headers in a header file and coding style in the
     wakeup IRQs handling code (Ulf Hansson, Xiaofei Tan)

   - Clean up the SmartReflex adaptive voltage scaling (AVS) driver for
     ARM (Ben Dooks, Geert Uytterhoeven)

   - Wrap power management documentation to fit in 80 columns (Bjorn
     Helgaas)

   - Add pm-graph utility entry to MAINTAINERS (Todd Brandt)

   - Update the cpupower utility:
      * Fix the handling of set and info subcommands (Abhishek Goel)
      * Fix build warnings (Nathan Chancellor)
      * Improve mperf_monitor handling (Janakarajan Natarajan)"

* tag 'pm-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (83 commits)
  PM: Wrap documentation to fit in 80 columns
  cpuidle: Pass exit latency limit to cpuidle_use_deepest_state()
  cpuidle: Allow idle injection to apply exit latency limit
  cpuidle: Introduce cpuidle_driver_state_disabled() for driver quirks
  cpuidle: teo: Avoid code duplication in conditionals
  cpufreq: Register drivers only after CPU devices have been registered
  cpuidle: teo: Avoid using "early hits" incorrectly
  cpuidle: teo: Exclude cpuidle overhead from computations
  PM / Domains: Convert to dev_to_genpd_safe() in genpd_syscore_switch()
  mmc: tmio: Avoid boilerplate code in ->runtime_suspend()
  PM / Domains: Implement the ->start() callback for genpd
  PM / Domains: Introduce dev_pm_domain_start()
  ARM: OMAP2+: SmartReflex: add omap_sr_pdata definition
  PM / wakeirq: remove unnecessary parentheses
  power: avs: smartreflex: Remove superfluous cast in debugfs_create_file() call
  cpuidle: Use nanoseconds as the unit of time
  PM / OPP: Support adjusting OPP voltages at runtime
  PM / core: Clean up some function headers in power.h
  cpufreq: Add NULL checks to show() and store() methods of cpufreq
  cpufreq: intel_pstate: Fix plain int as pointer warning from sparse
  ...

Pull x86 merge fix from Ingo Molnar:
 "I missed one other semantic conflict that can result in build failures
  on certain stripped down x86 32-bit configs, for example 32-bit
  'allnoconfig' where CONFIG_X86_IOPL_IOPERM gets turned off"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/iopl: Make 'struct tss_struct' constant size again

Pull locking updates from Ingo Molnar:
 "The main changes in this cycle were:

   - A comprehensive rewrite of the robust/PI futex code's exit handling
     to fix various exit races. (Thomas Gleixner et al)

   - Rework the generic REFCOUNT_FULL implementation using
     atomic_fetch_* operations so that the performance impact of the
     cmpxchg() loops is mitigated for common refcount operations.

     With these performance improvements the generic implementation of
     refcount_t should be good enough for everybody - and this got
     confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
     REFCOUNT_FULL entirely, leaving the generic implementation enabled
     unconditionally. (Will Deacon)

   - Other misc changes, fixes, cleanups"

* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  lkdtm: Remove references to CONFIG_REFCOUNT_FULL
  locking/refcount: Remove unused 'refcount_error_report()' function
  locking/refcount: Consolidate implementations of refcount_t
  locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
  locking/refcount: Move saturation warnings out of line
  locking/refcount: Improve performance of generic REFCOUNT_FULL code
  locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
  locking/refcount: Remove unused refcount_*_checked() variants
  locking/refcount: Ensure integer operands are treated as signed
  locking/refcount: Define constants for saturation and max refcount values
  futex: Prevent exit livelock
  futex: Provide distinct return value when owner is exiting
  futex: Add mutex around futex exit
  futex: Provide state handling for exec() as well
  futex: Sanitize exit state handling
  futex: Mark the begin of futex exit explicitly
  futex: Set task::futex_state to DEAD right after handling futex exit
  futex: Split futex_mm_release() for exit/exec
  exit/exec: Seperate mm_release()
  futex: Replace PF_EXITPIDONE with a state
  ...

Pull RCU updates from Ingo Molnar:
 "The main changes in this cycle were:

   - Dynamic tick (nohz) updates, perhaps most notably changes to force
     the tick on when needed due to lengthy in-kernel execution on CPUs
     on which RCU is waiting.

   - Linux-kernel memory consistency model updates.

   - Replace rcu_swap_protected() with rcu_prepace_pointer().

   - Torture-test updates.

   - Documentation updates.

   - Miscellaneous fixes"

* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
  security/safesetid: Replace rcu_swap_protected() with rcu_replace_pointer()
  net/sched: Replace rcu_swap_protected() with rcu_replace_pointer()
  net/netfilter: Replace rcu_swap_protected() with rcu_replace_pointer()
  net/core: Replace rcu_swap_protected() with rcu_replace_pointer()
  bpf/cgroup: Replace rcu_swap_protected() with rcu_replace_pointer()
  fs/afs: Replace rcu_swap_protected() with rcu_replace_pointer()
  drivers/scsi: Replace rcu_swap_protected() with rcu_replace_pointer()
  drm/i915: Replace rcu_swap_protected() with rcu_replace_pointer()
  x86/kvm/pmu: Replace rcu_swap_protected() with rcu_replace_pointer()
  rcu: Upgrade rcu_swap_protected() to rcu_replace_pointer()
  rcu: Suppress levelspread uninitialized messages
  rcu: Fix uninitialized variable in nocb_gp_wait()
  rcu: Update descriptions for rcu_future_grace_period tracepoint
  rcu: Update descriptions for rcu_nocb_wake tracepoint
  rcu: Remove obsolete descriptions for rcu_barrier tracepoint
  rcu: Ensure that ->rcu_urgent_qs is set before resched IPI
  workqueue: Convert for_each_wq to use built-in list check
  rcu: Several rcu_segcblist functions can be static
  rcu: Remove unused function hlist_bl_del_init_rcu()
  Documentation: Rename rcu_node_context_switch() to rcu_note_context_switch()
  ...

Pull scheduler updates from Ingo Molnar:
 "The biggest changes in this cycle were:

   - Make kcpustat vtime aware (Frederic Weisbecker)

   - Rework the CFS load_balance() logic (Vincent Guittot)

   - Misc cleanups, smaller enhancements, fixes.

  The load-balancing rework is the most intrusive change: it replaces
  the old heuristics that have become less meaningful after the
  introduction of the PELT metrics, with a grounds-up load-balancing
  algorithm.

  As such it's not really an iterative series, but replaces the old
  load-balancing logic with the new one. We hope there are no
  performance regressions left - but statistically it's highly probable
  that there *is* going to be some workload that is hurting from these
  chnages. If so then we'd prefer to have a look at that workload and
  fix its scheduling, instead of reverting the changes"

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
  rackmeter: Use vtime aware kcpustat accessor
  leds: Use all-in-one vtime aware kcpustat accessor
  cpufreq: Use vtime aware kcpustat accessors for user time
  procfs: Use all-in-one vtime aware kcpustat accessor
  sched/vtime: Bring up complete kcpustat accessor
  sched/cputime: Support other fields on kcpustat_field()
  sched/cpufreq: Move the cfs_rq_util_change() call to cpufreq_update_util()
  sched/fair: Add comments for group_type and balancing at SD_NUMA level
  sched/fair: Fix rework of find_idlest_group()
  sched/uclamp: Fix overzealous type replacement
  sched/Kconfig: Fix spelling mistake in user-visible help text
  sched/core: Further clarify sched_class::set_next_task()
  sched/fair: Use mul_u32_u32()
  sched/core: Simplify sched_class::pick_next_task()
  sched/core: Optimize pick_next_task()
  sched/core: Make pick_next_task_idle() more consistent
  sched/fair: Better document newidle_balance()
  leds: Use vtime aware kcpustat accessor to fetch CPUTIME_SYSTEM
  cpufreq: Use vtime aware kcpustat accessor to fetch CPUTIME_SYSTEM
  procfs: Use vtime aware kcpustat accessor to fetch CPUTIME_SYSTEM
  ...

Pull perf updates from Ingo Molnar:
 "The main kernel side changes in this cycle were:

   - Various Intel-PT updates and optimizations (Alexander Shishkin)

   - Prohibit kprobes on Xen/KVM emulate prefixes (Masami Hiramatsu)

   - Add support for LSM and SELinux checks to control access to the
     perf syscall (Joel Fernandes)

   - Misc other changes, optimizations, fixes and cleanups - see the
     shortlog for details.

  There were numerous tooling changes as well - 254 non-merge commits.
  Here are the main changes - too many to list in detail:

   - Enhancements to core tooling infrastructure, perf.data, libperf,
     libtraceevent, event parsing, vendor events, Intel PT, callchains,
     BPF support and instruction decoding.

   - There were updates to the following tools:

        perf annotate
        perf diff
        perf inject
        perf kvm
        perf list
        perf maps
        perf parse
        perf probe
        perf record
        perf report
        perf script
        perf stat
        perf test
        perf trace

   - And a lot of other changes: please see the shortlog and Git log for
     more details"

* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (279 commits)
  perf parse: Fix potential memory leak when handling tracepoint errors
  perf probe: Fix spelling mistake "addrees" -> "address"
  libtraceevent: Fix memory leakage in copy_filter_type
  libtraceevent: Fix header installation
  perf intel-bts: Does not support AUX area sampling
  perf intel-pt: Add support for decoding AUX area samples
  perf intel-pt: Add support for recording AUX area samples
  perf pmu: When using default config, record which bits of config were changed by the user
  perf auxtrace: Add support for queuing AUX area samples
  perf session: Add facility to peek at all events
  perf auxtrace: Add support for dumping AUX area samples
  perf inject: Cut AUX area samples
  perf record: Add aux-sample-size config term
  perf record: Add support for AUX area sampling
  perf auxtrace: Add support for AUX area sample recording
  perf auxtrace: Move perf_evsel__find_pmu()
  perf record: Add a function to test for kernel support for AUX area sampling
  perf tools: Add kernel AUX area sampling definitions
  perf/core: Make the mlock accounting simple again
  perf report: Jump to symbol source view from total cycles view
  ...

Pull EFI updates from Ingo Molnar:
 "The main changes in this cycle were:

   - Wire up the EFI RNG code for x86. This enables an additional source
     of entropy during early boot.

   - Enable the TPM event log code on ARM platforms.

   - Update Ard's email address"

* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi: libstub/tpm: enable tpm eventlog function for ARM platforms
  x86: efi/random: Invoke EFI_RNG_PROTOCOL to seed the UEFI RNG table
  efi/random: use arch-independent efi_call_proto()
  MAINTAINERS: update Ard's email address to @kernel.org

Pull stacktrace cleanup from Ingo Molnar:
 "A minor cleanup"

* 'core-stacktrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  stacktrace: Get rid of unneeded '!!' pattern

After the following commit:

  05b042a1: ("x86/pti/32: Calculate the various PTI cpu_entry_area sizes correctly, make the CPU_ENTRY_AREA_PAGES assert precise")

'struct cpu_entry_area' has to be Kconfig invariant, so that we always
have a matching CPU_ENTRY_AREA_PAGES size.

This commit added a CONFIG_X86_IOPL_IOPERM dependency to tss_struct:

  111e7b15: ("x86/ioperm: Extend IOPL config to control ioperm() as well")

Which, if CONFIG_X86_IOPL_IOPERM is turned off, reduces the size of
cpu_entry_area by two pages, triggering the assert:

  ./include/linux/compiler.h:391:38: error: call to ‘__compiletime_assert_202’ declared with attribute error: BUILD_BUG_ON failed: (CPU_ENTRY_AREA_PAGES+1)*PAGE_SIZE != CPU_ENTRY_AREA_MAP_SIZE

Simplify the Kconfig dependencies and make cpu_entry_area constant
size on 32-bit kernels again.

Fixes: 05b042a1: ("x86/pti/32: Calculate the various PTI cpu_entry_area sizes correctly, make the CPU_ENTRY_AREA_PAGES assert precise")
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

This reverts commit 0be0ee71.

I was hoping it would be benign to switch over entirely to FMODE_STREAM,
and we'd have just a couple of small fixups we'd need, but it looks like
we're not quite there yet.

While it worked fine on both my desktop and laptop, they are fairly
similar in other respects, and run mostly the same loads.  Kenneth
Crudup reports that it seems to break both his vmware installation and
the KDE upower service.  In both cases apparently leading to timeouts
due to waitinmg for the f_pos lock.

There are a number of character devices in particular that definitely
want stream-like behavior, but that currently don't get marked as
streams, and as a result get the exclusion between concurrent
read()/write() on the same file descriptor.  Which doesn't work well for
them.

The most obvious example if this is /dev/console and /dev/tty, which use
console_fops and tty_fops respectively (and ptmx_fops for the pty master
side).  It may be that it's just this that causes problems, but we
clearly weren't ready yet.

Because there's a number of other likely common cases that don't have
llseek implementations and would seem to act as stream devices:

  /dev/fuse		(fuse_dev_operations)
  /dev/mcelog		(mce_chrdev_ops)
  /dev/mei0		(mei_fops)
  /dev/net/tun		(tun_fops)
  /dev/nvme0		(nvme_dev_fops)
  /dev/tpm0		(tpm_fops)
  /proc/self/ns/mnt	(ns_file_operations)
  /dev/snd/pcm*		(snd_pcm_f_ops[])

and while some of these could be trivially automatically detected by the
vfs layer when the character device is opened by just noticing that they
have no read or write operations either, it often isn't that obvious.

Some character devices most definitely do use the file position, even if
they don't allow seeking: the firmware update code, for example, uses
simple_read_from_buffer() that does use f_pos, but doesn't allow seeking
back and forth.

We'll revisit this when there's a better way to detect the problem and
fix it (possibly with a coccinelle script to do more of the FMODE_STREAM
annotations).
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Cc: Kirill Smelkov <kirr@nexedi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull x86 iopl updates from Ingo Molnar:
 "This implements a nice simplification of the iopl and ioperm code that
  Thomas Gleixner discovered: we can implement the IO privilege features
  of the iopl system call by using the IO permission bitmap in
  permissive mode, while trapping CLI/STI/POPF/PUSHF uses in user-space
  if they change the interrupt flag.

  This implements that feature, with testing facilities and related
  cleanups"

[ "Simplification" may be an over-statement. The main goal is to avoid
  the cli/sti of iopl by effectively implementing the IO port access
  parts of iopl in terms of ioperm.

  This may end up not workign well in case people actually depend on
  cli/sti being available, or if there are mixed uses of iopl and
  ioperm. We will see..       - Linus ]

* 'x86-iopl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
  x86/ioperm: Fix use of deprecated config option
  x86/entry/32: Clarify register saving in __switch_to_asm()
  selftests/x86/iopl: Extend test to cover IOPL emulation
  x86/ioperm: Extend IOPL config to control ioperm() as well
  x86/iopl: Remove legacy IOPL option
  x86/iopl: Restrict iopl() permission scope
  x86/iopl: Fixup misleading comment
  selftests/x86/ioperm: Extend testing so the shared bitmap is exercised
  x86/ioperm: Share I/O bitmap if identical
  x86/ioperm: Remove bitmap if all permissions dropped
  x86/ioperm: Move TSS bitmap update to exit to user work
  x86/ioperm: Add bitmap sequence number
  x86/ioperm: Move iobitmap data into a struct
  x86/tss: Move I/O bitmap data into a seperate struct
  x86/io: Speedup schedule out of I/O bitmap user
  x86/ioperm: Avoid bitmap allocation if no permissions are set
  x86/ioperm: Simplify first ioperm() invocation logic
  x86/iopl: Cleanup include maze
  x86/tss: Fix and move VMX BUILD_BUG_ON()
  x86/cpu: Unify cpu_init()
  ...

Pull x86 asm updates from Ingo Molnar:
 "The main changes in this cycle were:

   - Cross-arch changes to move the linker sections for NOTES and
     EXCEPTION_TABLE into the RO_DATA area, where they belong on most
     architectures. (Kees Cook)

   - Switch the x86 linker fill byte from x90 (NOP) to 0xcc (INT3), to
     trap jumps into the middle of those padding areas instead of
     sliding execution. (Kees Cook)

   - A thorough cleanup of symbol definitions within x86 assembler code.
     The rather randomly named macros got streamlined around a
     (hopefully) straightforward naming scheme:

        SYM_START(name, linkage, align...)
        SYM_END(name, sym_type)

        SYM_FUNC_START(name)
        SYM_FUNC_END(name)

        SYM_CODE_START(name)
        SYM_CODE_END(name)

        SYM_DATA_START(name)
        SYM_DATA_END(name)

     etc - with about three times of these basic primitives with some
     label, local symbol or attribute variant, expressed via postfixes.

     No change in functionality intended. (Jiri Slaby)

   - Misc other changes, cleanups and smaller fixes"

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (67 commits)
  x86/entry/64: Remove pointless jump in paranoid_exit
  x86/entry/32: Remove unused resume_userspace label
  x86/build/vdso: Remove meaningless CFLAGS_REMOVE_*.o
  m68k: Convert missed RODATA to RO_DATA
  x86/vmlinux: Use INT3 instead of NOP for linker fill bytes
  x86/mm: Report actual image regions in /proc/iomem
  x86/mm: Report which part of kernel image is freed
  x86/mm: Remove redundant address-of operators on addresses
  xtensa: Move EXCEPTION_TABLE to RO_DATA segment
  powerpc: Move EXCEPTION_TABLE to RO_DATA segment
  parisc: Move EXCEPTION_TABLE to RO_DATA segment
  microblaze: Move EXCEPTION_TABLE to RO_DATA segment
  ia64: Move EXCEPTION_TABLE to RO_DATA segment
  h8300: Move EXCEPTION_TABLE to RO_DATA segment
  c6x: Move EXCEPTION_TABLE to RO_DATA segment
  arm64: Move EXCEPTION_TABLE to RO_DATA segment
  alpha: Move EXCEPTION_TABLE to RO_DATA segment
  x86/vmlinux: Move EXCEPTION_TABLE to RO_DATA segment
  x86/vmlinux: Actually use _etext for the end of the text segment
  vmlinux.lds.h: Allow EXCEPTION_TABLE to live in RO_DATA
  ...

Pull x86 fixes from Ingo Molnar:
 "These are the fixes left over from the v5.4 cycle:

   - Various low level 32-bit entry code fixes and improvements by Andy
     Lutomirski, Peter Zijlstra and Thomas Gleixner.

   - Fix 32-bit Xen PV breakage, by Jan Beulich"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/entry/32: Fix FIXUP_ESPFIX_STACK with user CR3
  x86/pti/32: Calculate the various PTI cpu_entry_area sizes correctly, make the CPU_ENTRY_AREA_PAGES assert precise
  selftests/x86/sigreturn/32: Invalidate DS and ES when abusing the kernel
  selftests/x86/mov_ss_trap: Fix the SYSENTER test
  x86/entry/32: Fix NMI vs ESPFIX
  x86/entry/32: Unwind the ESPFIX stack earlier on exception entry
  x86/entry/32: Move FIXUP_FRAME after pushing %fs in SAVE_ALL
  x86/entry/32: Use %ss segment where required
  x86/entry/32: Fix IRET exception
  x86/cpu_entry_area: Add guard page for entry stack on 32bit
  x86/pti/32: Size initial_page_table correctly
  x86/doublefault/32: Fix stack canaries in the double fault handler
  x86/xen/32: Simplify ring check in xen_iret_crit_fixup()
  x86/xen/32: Make xen_iret_crit_fixup() independent of frame layout
  x86/stackframe/32: Repair 32-bit Xen PV

Pull x86 PTI updates from Ingo Molnar:
 "Fix reporting bugs of the MDS and TAA mitigation status, if one or
  both are set via a boot option.

  No change to mitigation behavior intended"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/speculation: Fix redundant MDS mitigation message
  x86/speculation: Fix incorrect MDS/TAA mitigation status

Pull x86 platform updates from Ingo Molnar:
 "UV platform updates (with a 'hubless' variant) and Jailhouse updates
  for better UART support"

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/jailhouse: Only enable platform UARTs if available
  x86/jailhouse: Improve setup data version comparison
  x86/platform/uv: Account for UV Hubless in is_uvX_hub Ops
  x86/platform/uv: Check EFI Boot to set reboot type
  x86/platform/uv: Decode UVsystab Info
  x86/platform/uv: Add UV Hubbed/Hubless Proc FS Files
  x86/platform/uv: Setup UV functions for Hubless UV Systems
  x86/platform/uv: Add return code to UV BIOS Init function
  x86/platform/uv: Return UV Hubless System Type
  x86/platform/uv: Save OEM_ID from ACPI MADT probe

Pull x86 mm updates from Ingo Molnar:
 "The main changes in this cycle were:

   - A PAT series from Davidlohr Bueso, which simplifies the memtype
     rbtree by using the interval tree helpers. (There's more cleanups
     in this area queued up, but they didn't make the merge window.)

   - Also flip over CONFIG_X86_5LEVEL to default-y. This might draw in a
     few more testers, as all the major distros are going to have
     5-level paging enabled by default in their next iterations.

   - Misc cleanups"

* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/pat: Rename pat_rbtree.c to pat_interval.c
  x86/mm/pat: Drop the rbt_ prefix from external memtype calls
  x86/mm/pat: Do not pass 'rb_root' down the memtype tree helper functions
  x86/mm/pat: Convert the PAT tree to a generic interval tree
  x86/mm: Clean up the pmd_read_atomic() comments
  x86/mm: Fix function name typo in pmd_read_atomic() comment
  x86/cpu: Clean up intel_tlb_table[]
  x86/mm: Enable 5-level paging support by default

Pull x86 kdump updates from Ingo Molnar:
 "This solves a kdump artifact where encrypted memory contents are
  dumped, instead of unencrypted ones.

  The solution also happens to simplify the kdump code, to everyone's
  delight"

* 'x86-kdump-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/crash: Align function arguments on opening braces
  x86/kdump: Remove the backup region handling
  x86/kdump: Always reserve the low 1M when the crashkernel option is specified
  x86/crash: Add a forward declaration of struct kimage

Pull x86 hyperv updates from Ingo Molnar:
 "Misc updates to the hyperv guest code:

   - Rework clockevents initialization to better support hibernation

   - Allow guests to enable InvariantTSC

   - Micro-optimize send_ipi_one"

* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/hyperv: Initialize clockevents earlier in CPU onlining
  x86/hyperv: Allow guests to enable InvariantTSC
  x86/hyperv: Micro-optimize send_ipi_one()

Pull x86 syscall entry updates from Ingo Molnar:
 "These changes relate to the preparatory cleanup of syscall function
  type signatures - to fix indirect call mismatches with Control-Flow
  Integrity (CFI) checking.

  No change in behavior intended"

* 'x86-entry-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Use the correct function type for native_set_fixmap()
  syscalls/x86: Fix function types in COND_SYSCALL
  syscalls/x86: Use the correct function type for sys_ni_syscall
  syscalls/x86: Use COMPAT_SYSCALL_DEFINE0 for IA32 (rt_)sigreturn
  syscalls/x86: Wire up COMPAT_SYSCALL_DEFINE0
  syscalls/x86: Use the correct function type in SYSCALL_DEFINE0

Merge branches 'x86-cpu-for-linus' and 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull x86 cpu and fpu updates from Ingo Molnar:

 - math-emu fixes

 - CPUID updates

 - sanity-check RDRAND output to see whether the CPU at least pretends
   to produce random data

 - various unaligned-access across cachelines fixes in preparation of
   hardware level split-lock detection

 - fix MAXSMP constraints to not allow !CPUMASK_OFFSTACK kernels with
   larger than 512 NR_CPUS

 - misc FPU related cleanups

* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Align the x86_capability array to size of unsigned long
  x86/cpu: Align cpu_caps_cleared and cpu_caps_set to unsigned long
  x86/umip: Make the comments vendor-agnostic
  x86/Kconfig: Rename UMIP config parameter
  x86/Kconfig: Enforce limit of 512 CPUs with MAXSMP and no CPUMASK_OFFSTACK
  x86/cpufeatures: Add feature bit RDPRU on AMD
  x86/math-emu: Limit MATH_EMULATION to 486SX compatibles
  x86/math-emu: Check __copy_from_user() result
  x86/rdrand: Sanity-check RDRAND output

* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/fpu: Use XFEATURE_FP/SSE enum values instead of hardcoded numbers
  x86/fpu: Shrink space allocated for xstate_comp_offsets
  x86/fpu: Update stale variable name in comment

Pull x86 boot updates from Ingo Molnar:
 "The main changes were:

   - Extend the boot protocol to allow future extensions without hitting
     the setup_header size limit.

   - Add quirk to devicetree systems to disable the RTC unless it's
     listed as a supported device.

   - Fix ld.lld linker pedantry"

* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Introduce setup_indirect
  x86/boot: Introduce kernel_info.setup_type_max
  x86/boot: Introduce kernel_info
  x86/init: Allow DT configured systems to disable RTC at boot time
  x86/realmode: Explicitly set entry point via ENTRY in linker script

Merge branches 'core-objtool-for-linus', 'x86-cleanups-for-linus' and 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull x86 objtool, cleanup, and apic updates from Ingo Molnar:
 "Objtool:

   - Fix a gawk 5.0 incompatibility in gen-insn-attr-x86.awk. Most
     distros are still on gawk 4.2.x.

  Cleanup:

   - Misc cleanups, plus the removal of obsolete code such as Calgary
     IOMMU support, which code hasn't seen any real testing in a long
     time and there's no known users left.

  apic:

   - Two changes: a cleanup and a fix for an (old) race for oneshot
     threaded IRQ handlers"

* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/insn: Fix awk regexp warnings

* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Remove unused asm/rio.h
  x86: Fix typos in comments
  x86/pci: Remove #ifdef __KERNEL__ guard from <asm/pci.h>
  x86/pci: Remove pci_64.h
  x86: Remove the calgary IOMMU driver
  x86/apic, x86/uprobes: Correct parameter names in kernel-doc comments
  x86/kdump: Remove the unused crash_copy_backup_region()
  x86/nmi: Remove stale EDAC include leftover

* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ioapic: Rename misnamed functions
  x86/ioapic: Prevent inconsistent state when moving an interrupt

* pm-avs:
  ARM: OMAP2+: SmartReflex: add omap_sr_pdata definition
  power: avs: smartreflex: Remove superfluous cast in debugfs_create_file() call

* pm-docs:
  PM: Wrap documentation to fit in 80 columns

* pm-tools:
  cpupower: ToDo: Update ToDo with ideas for per_cpu_schedule handling
  cpupower: mperf_monitor: Update cpupower to use the RDPRU instruction
  cpupower: mperf_monitor: Introduce per_cpu_schedule flag
  cpupower: Move needs_root variable into a sub-struct
  cpupower : Handle set and info subcommands correctly
  pm-graph info added to MAINTAINERS
  tools/power/cpupower: Fix initializer override in hsw_ext_cstates

* pm-sleep:
  PM / wakeirq: remove unnecessary parentheses
  PM / core: Clean up some function headers in power.h
  PM / hibernate: memory_bm_find_bit(): Tighten node optimisation

* pm-domains:
  PM / Domains: Convert to dev_to_genpd_safe() in genpd_syscore_switch()
  mmc: tmio: Avoid boilerplate code in ->runtime_suspend()
  PM / Domains: Implement the ->start() callback for genpd
  PM / Domains: Introduce dev_pm_domain_start()

* pm-opp:
  PM / OPP: Support adjusting OPP voltages at runtime

* powercap:
  powercap/intel_rapl: add support for Cometlake desktop
  powercap/intel_rapl: add support for CometLake Mobile

* pm-devfreq: (26 commits)
  PM / devfreq: tegra30: Tune up MCCPU boost-down coefficient
  PM / devfreq: tegra30: Support variable polling interval
  PM / devfreq: Add new interrupt_driven flag for governors
  PM / devfreq: tegra30: Use kHz units for dependency threshold
  PM / devfreq: tegra30: Disable consecutive interrupts when appropriate
  PM / devfreq: tegra30: Don't enable already enabled consecutive interrupts
  PM / devfreq: tegra30: Include appropriate header
  PM / devfreq: tegra30: Constify structs
  PM / devfreq: tegra30: Don't enable consecutive-down interrupt on startup
  PM / devfreq: tegra30: Reset boosting on startup
  PM / devfreq: tegra30: Move clk-notifier's registration to governor's start
  PM / devfreq: tegra30: Use CPUFreq notifier
  PM / devfreq: tegra30: Use kHz units uniformly in the code
  PM / devfreq: tegra30: Fix integer overflow on CPU's freq max out
  PM / devfreq: tegra30: Drop write-barrier
  PM / devfreq: tegra30: Handle possible round-rate error
  PM / devfreq: tegra30: Keep interrupt disabled while governor is stopped
  PM / devfreq: tegra30: Change irq type to unsigned int
  PM / devfreq: exynos-ppmu: remove useless assignment
  PM / devfreq: Lock devfreq in trans_stat_show
  ...

* pm-cpufreq: (23 commits)
  cpufreq: Register drivers only after CPU devices have been registered
  cpufreq: Add NULL checks to show() and store() methods of cpufreq
  cpufreq: intel_pstate: Fix plain int as pointer warning from sparse
  cpufreq: sun50i: Fix CPU speed bin detection
  cpufreq: powernv: fix stack bloat and hard limit on number of CPUs
  cpufreq: Clarify the comment in cpufreq_set_policy()
  cpufreq: vexpress-spc: find and skip duplicates when merging frequencies
  cpufreq: vexpress-spc: use macros instead of hardcoded values for cluster ids
  cpufreq: s3c64xx: Remove pointless NULL check in s3c64xx_cpufreq_driver_init
  cpufreq: imx-cpufreq-dt: Correct i.MX8MN's default speed grade value
  cpufreq: vexpress-spc: fix some coding style issues
  cpufreq: vexpress-spc: remove lots of debug messages
  cpufreq: vexpress-spc: drop unnessary cpufreq_arm_bL_ops abstraction
  cpufreq: merge arm_big_little and vexpress-spc
  cpufreq: scpi: remove stale/outdated comment about the driver
  ARM: dts: Add OPP-V2 table for AM3517
  cpufreq: ti-cpufreq: Add support for AM3517
  ARM: dts: omap36xx: using OPP1G needs to control the abb_ldo
  cpufreq: ti-cpufreq: omap36xx use "cpu0","vbb" if run in multi_regulator mode
  ARM: dts: omap3: bulk convert compatible to be explicitly ti,omap3430 or ti,omap3630 or ti,am3517
  ...

* pm-cpuidle:
  cpuidle: Pass exit latency limit to cpuidle_use_deepest_state()
  cpuidle: Allow idle injection to apply exit latency limit
  cpuidle: Introduce cpuidle_driver_state_disabled() for driver quirks
  cpuidle: teo: Avoid code duplication in conditionals
  cpuidle: teo: Avoid using "early hits" incorrectly
  cpuidle: teo: Exclude cpuidle overhead from computations
  cpuidle: Use nanoseconds as the unit of time
  cpuidle: Consolidate disabled state checks
  ACPI: processor_idle: Skip dummy wait if kernel is in guest
  cpuidle: Do not unset the driver if it is there already
  cpuidle: teo: Fix "early hits" handling for disabled idle states
  cpuidle: teo: Consider hits and misses metrics of disabled states
  cpuidle: teo: Rename local variable in teo_select()
  cpuidle: teo: Ignore disabled idle states that are too deep

Pull IPMI updates from Corey Minyard:
 "Some small fixes accumulated for IPMI, nothing major"

* tag 'for-linus-5.5-1' of git://github.com/cminyard/linux-ipmi:
  ipmi: fix ipmb_poll()'s return type
  ipmi: kill off 'timespec' usage again
  drivers: ipmi: Support for both IPMB Req and Resp
  ipmi: Fix memory leak in __ipmi_bmc_register
  ipmi: bt-bmc: use devm_platform_ioremap_resource() to simplify code
  ipmi: use %*ph to print small buffer
  ipmi: Don't allow device module unload when in use

Pull i3c updates from Boris Brezillon:
 "Minor fixes and MAINTAINERS updates"

* tag 'i3c/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
  MAINTAINERS: add myself as maintainer of Cadence I3C master controller driver
  MAINTAINERS: Mark linux-i3c mailing list moderated
  i3c: Spelling s/dicovered/discovered/
  i3c: master: use i3c_dev_get_master()

Pull pcmcia updates from Dominik Brodowski:
 "Just a few odd fixes and improvements to the PCMCIA core"

* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
  pcmcia: remove unused dprintk definition
  pcmcia: include <pcmcia/ds.h> for pcmcia_parse_tuple
  pcmcia: include cs_internal.h for missing declarations
  pcmcia: Use dev_get_drvdata where possible
  pcmcia: clean an indentation issues, remove extraneous spaces

Pull spi updates from Mark Brown:
 "Lots of stuff going on in the core for SPI this time around, the two
  big changes both being around time in different forms:

   - A rework of delay times from Alexandru Ardelean which makes the
     ways in which they are specified more consistent between drivers so
     that what's available to clients is less dependent on the hardware
     implementation.

   - Support for PTP timestamping of transfers from Vladimir Oltean,
     useful for use with precision clocks with SPI control interfaces.

   - Big cleanups for the Atmel, PXA2xx and Zynq QSPI drivers"

* tag 'spi-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (119 commits)
  dt-bindings: spi: Convert stm32 QSPI bindings to json-schema
  spi: pic32: Retire dma_request_slave_channel_compat()
  spi: Fix Kconfig indentation
  spi: mediatek: add SPI_CS_HIGH support
  spi: st-ssc4: add missed pm_runtime_disable
  spi: tegra20-slink: add missed clk_unprepare
  spi: tegra20-slink: Use dma_request_chan() directly for channel request
  spi: tegra114: Use dma_request_chan() directly for channel request
  spi: s3c64xx: Use dma_request_chan() directly for channel request
  spi: qup: Use dma_request_chan() directly for channel request
  spi: pl022: Use dma_request_chan() directly for channel request
  spi: imx: Use dma_request_chan() directly for channel request
  spi: fsl-lpspi: Use dma_request_chan() directly for channel request
  spi: atmel: Use dma_request_chan() directly for channel request
  spi: at91-usart: Use dma_request_chan() directly for channel request
  spi: fsl-cpm: Correct the free:ing
  spi: Fix regression to return zero on success instead of positive value
  spi: pxa2xx: Add missed security checks
  spi: nxp-fspi: Use devm API to fix missed unregistration of controller
  spi: omap2-mcspi: Remove redundant checks
  ...

Pull regulator updates from Mark Brown:
 "Another fairly quiet release for the regulator API, some work all
  around including some core work but mostly in specialist or driver
  specific code:

   - Fix for powering off boot-on regulators

   - Enhancements to the coupled regulator support introduced in the
     last release

   - Conversion of a bunch of drivers to the fwnode API for GPIOs

   - Mode support for DA9062

   - New device support for Qualcomm PM1650, PM8004 and PM895 and
     Silergy SR83X

   - Removal of obsolete AB8505 support"

* tag 'regulator-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (49 commits)
  regulator: da9062: Return REGULATOR_MODE_INVALID for invalid mode
  regulator: Fix Kconfig indentation
  regulator: tps6105x: add optional devicetree support
  tps6105x: add optional devicetree support
  regulator: rn5t618: fix rc5t619 ldo10 enable
  regulator: vexpress: Use PTR_ERR_OR_ZERO() to simplify code
  dt-bindings: mfd: da9062: describe buck modes
  regulator: da9062: add of_map_mode support for bucks
  regulator: da9062: refactor buck modes into header
  regulator: stpmic1: Set a default ramp delay value
  regulator: core: Let boot-on regulators be powered off
  regulator: core: Don't try to remove device links if add failed
  regulator: ab8500: Remove SYSCLKREQ from enum ab8505_regulator_id
  regulator: ab8500: Remove AB8505 USB regulator
  regulator: fan53555: add chip id for Silergy SYR83X
  regulator: fixed: add off-on-delay
  dt-bindings: regulator: fixed: add off-on-delay-us property
  regulator: core: Allow generic coupling only for always-on regulators
  regulator: core: Release coupled_rdevs on regulator_init_coupling() error
  regulator: bd70528: Add MODULE_ALIAS to allow module auto loading
  ...

Pull regmap update from Mark Brown:
 "Just one patch for this release removing some dead code"

* tag 'regmap-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: regmap-w1: Drop unreachable code

Pull networking updates from David Miller:
 "Another merge window, another pull full of stuff:

   1) Support alternative names for network devices, from Jiri Pirko.

   2) Introduce per-netns netdev notifiers, also from Jiri Pirko.

   3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara
      Larsen.

   4) Allow compiling out the TLS TOE code, from Jakub Kicinski.

   5) Add several new tracepoints to the kTLS code, also from Jakub.

   6) Support set channels ethtool callback in ena driver, from Sameeh
      Jubran.

   7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED,
      SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long.

   8) Add XDP support to mvneta driver, from Lorenzo Bianconi.

   9) Lots of netfilter hw offload fixes, cleanups and enhancements,
      from Pablo Neira Ayuso.

  10) PTP support for aquantia chips, from Egor Pomozov.

  11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From
      Josh Hunt.

  12) Add smart nagle to tipc, from Jon Maloy.

  13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat
      Duvvuru.

  14) Add a flow mask cache to OVS, from Tonghao Zhang.

  15) Add XDP support to ice driver, from Maciej Fijalkowski.

  16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak.

  17) Support UDP GSO offload in atlantic driver, from Igor Russkikh.

  18) Support it in stmmac driver too, from Jose Abreu.

  19) Support TIPC encryption and auth, from Tuong Lien.

  20) Introduce BPF trampolines, from Alexei Starovoitov.

  21) Make page_pool API more numa friendly, from Saeed Mahameed.

  22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni.

  23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits)
  libbpf: Fix usage of u32 in userspace code
  mm: Implement no-MMU variant of vmalloc_user_node_flags
  slip: Fix use-after-free Read in slip_open
  net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
  macvlan: schedule bc_work even if error
  enetc: add support Credit Based Shaper(CBS) for hardware offload
  net: phy: add helpers phy_(un)lock_mdio_bus
  mdio_bus: don't use managed reset-controller
  ax88179_178a: add ethtool_op_get_ts_info()
  mlxsw: spectrum_router: Fix use of uninitialized adjacency index
  mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels
  bpf: Simplify __bpf_arch_text_poke poke type handling
  bpf: Introduce BPF_TRACE_x helper for the tracing tests
  bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT
  bpf, testing: Add various tail call test cases
  bpf, x86: Emit patchable direct jump as tail call
  bpf: Constant map key tracking for prog array pokes
  bpf: Add poke dependency tracking for prog array maps
  bpf: Add initial poke descriptor table for jit images
  bpf: Move owner type, jited info into array auxiliary data
  ...

Pull crypto updates from Herbert Xu:
 "API:
   - Add library interfaces of certain crypto algorithms for WireGuard
   - Remove the obsolete ablkcipher and blkcipher interfaces
   - Move add_early_randomness() out of rng_mutex

  Algorithms:
   - Add blake2b shash algorithm
   - Add blake2s shash algorithm
   - Add curve25519 kpp algorithm
   - Implement 4 way interleave in arm64/gcm-ce
   - Implement ciphertext stealing in powerpc/spe-xts
   - Add Eric Biggers's scalar accelerated ChaCha code for ARM
   - Add accelerated 32r2 code from Zinc for MIPS
   - Add OpenSSL/CRYPTOGRAMS poly1305 implementation for ARM and MIPS

  Drivers:
   - Fix entropy reading failures in ks-sa
   - Add support for sam9x60 in atmel
   - Add crypto accelerator for amlogic GXL
   - Add sun8i-ce Crypto Engine
   - Add sun8i-ss cryptographic offloader
   - Add a host of algorithms to inside-secure
   - Add NPCM RNG driver
   - add HiSilicon HPRE accelerator
   - Add HiSilicon TRNG driver"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (285 commits)
  crypto: vmx - Avoid weird build failures
  crypto: lib/chacha20poly1305 - use chacha20_crypt()
  crypto: x86/chacha - only unregister algorithms if registered
  crypto: chacha_generic - remove unnecessary setkey() functions
  crypto: amlogic - enable working on big endian kernel
  crypto: sun8i-ce - enable working on big endian
  crypto: mips/chacha - select CRYPTO_SKCIPHER, not CRYPTO_BLKCIPHER
  hwrng: ks-sa - Enable COMPILE_TEST
  crypto: essiv - remove redundant null pointer check before kfree
  crypto: atmel-aes - Change data type for "lastc" buffer
  crypto: atmel-tdes - Set the IV after {en,de}crypt
  crypto: sun4i-ss - fix big endian issues
  crypto: sun4i-ss - hide the Invalid keylen message
  crypto: sun4i-ss - use crypto_ahash_digestsize
  crypto: sun4i-ss - remove dependency on not 64BIT
  crypto: sun4i-ss - Fix 64-bit size_t warnings on sun4i-ss-hash.c
  MAINTAINERS: Add maintainer for HiSilicon SEC V2 driver
  crypto: hisilicon - add DebugFS for HiSilicon SEC
  Documentation: add DebugFS doc for HiSilicon SEC
  crypto: hisilicon - add SRIOV for HiSilicon SEC
  ...

Merge tag 'livepatching-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching

Pull livepatching updates from Petr Mladek:

 - New API to track system state changes done be livepatch callbacks. It
   helps to maintain compatibility between livepatches.

 - Update Kconfig help text. ORC is another reliable unwinder.

 - Disable generic selftest timeout. Livepatch selftests have their own
   per-operation fine-grained timeouts.

* tag 'livepatching-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
  x86/stacktrace: update kconfig help text for reliable unwinders
  livepatch: Selftests of the API for tracking system state changes
  livepatch: Documentation of the new API for tracking system state changes
  livepatch: Allow to distinguish different version of system state changes
  livepatch: Basic API to track system state changes
  livepatch: Keep replaced patches until post_patch callback is called
  selftests/livepatch: Disable the timeout

Pull printk updates from Petr Mladek:

 - Allow to print symbolic error names via new %pe modifier.

 - Use pr_warn() instead of the remaining pr_warning() calls. Fix
   formatting of the related lines.

 - Add VSPRINTF entry to MAINTAINERS.

* tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (32 commits)
  checkpatch: don't warn about new vsprintf pointer extension '%pe'
  MAINTAINERS: Add VSPRINTF
  tools lib api: Renaming pr_warning to pr_warn
  ASoC: samsung: Use pr_warn instead of pr_warning
  lib: cpu_rmap: Use pr_warn instead of pr_warning
  trace: Use pr_warn instead of pr_warning
  dma-debug: Use pr_warn instead of pr_warning
  vgacon: Use pr_warn instead of pr_warning
  fs: afs: Use pr_warn instead of pr_warning
  sh/intc: Use pr_warn instead of pr_warning
  scsi: Use pr_warn instead of pr_warning
  platform/x86: intel_oaktrail: Use pr_warn instead of pr_warning
  platform/x86: asus-laptop: Use pr_warn instead of pr_warning
  platform/x86: eeepc-laptop: Use pr_warn instead of pr_warning
  oprofile: Use pr_warn instead of pr_warning
  of: Use pr_warn instead of pr_warning
  macintosh: Use pr_warn instead of pr_warning
  idsn: Use pr_warn instead of pr_warning
  ide: Use pr_warn instead of pr_warning
  crypto: n2: Use pr_warn instead of pr_warning
  ...

Pull cgroup updates from Tejun Heo:
 "There are several notable changes here:

   - Single thread migrating itself has been optimized so that it
     doesn't need threadgroup rwsem anymore.

   - Freezer optimization to avoid unnecessary frozen state changes.

   - cgroup ID unification so that cgroup fs ino is the only unique ID
     used for the cgroup and can be used to directly look up live
     cgroups through filehandle interface on 64bit ino archs. On 32bit
     archs, cgroup fs ino is still the only ID in use but it is only
     unique when combined with gen.

   - selftest and other changes"

* 'for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (24 commits)
  writeback: fix -Wformat compilation warnings
  docs: cgroup: mm: Fix spelling of "list"
  cgroup: fix incorrect WARN_ON_ONCE() in cgroup_setup_root()
  cgroup: use cgrp->kn->id as the cgroup ID
  kernfs: use 64bit inos if ino_t is 64bit
  kernfs: implement custom exportfs ops and fid type
  kernfs: combine ino/id lookup functions into kernfs_find_and_get_node_by_id()
  kernfs: convert kernfs_node->id from union kernfs_node_id to u64
  kernfs: kernfs_find_and_get_node_by_ino() should only look up activated nodes
  kernfs: use dumber locking for kernfs_find_and_get_node_by_ino()
  netprio: use css ID instead of cgroup ID
  writeback: use ino_t for inodes in tracepoints
  kernfs: fix ino wrap-around detection
  kselftests: cgroup: Avoid the reuse of fd after it is deallocated
  cgroup: freezer: don't change task and cgroups status unnecessarily
  cgroup: use cgroup->last_bstat instead of cgroup->bstat_pending for consistency
  cgroup: remove cgroup_enable_task_cg_lists() optimization
  cgroup: pids: use atomic64_t for pids->limit
  selftests: cgroup: Run test_core under interfering stress
  selftests: cgroup: Add task migration tests
  ...

Pull workqueue updates from Tejun Heo:
 "There have been sporadic reports of sanity checks in
  destroy_workqueue() failing spuriously over the years. This contains
  the fix and its follow-up changes / fixes.

  There's also a RCU annotation improvement"

* 'for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: Add RCU annotation for pwq list walk
  workqueue: Fix pwq ref leak in rescuer_thread()
  workqueue: more destroy_workqueue() fixes
  workqueue: Minor follow-ups to the rescuer destruction change
  workqueue: Fix missing kfree(rescuer) in destroy_workqueue()
  workqueue: Fix spurious sanity check failures in destroy_workqueue()