Adding AES skcipher and aead support to Starfive crypto module.
Skcipher modes of operation include ecb, cbc, ctr, ofb, cfb. Aead modes
include ccm and gcm.

v1->v2:
- Add include interrupt.h to fix compile error. (Herbert)
Co-developed-by: Huan Feng <huan.feng@starfivetech.com>
Signed-off-by: Huan Feng <huan.feng@starfivetech.com>
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Don't set drvdata, there's nobody who reads it.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The 'tfm' parameter to aes_set_key_common() is never used, so remove it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Enable sva error interrupt event. When an error occurs on
the sva module, the device reports an abnormal interrupt to
the driver.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When both the accelerator device and SMMU are busy,
the processing time of the doorbell may be prolonged.
As a result, the doorbell may timeout, especially in the sva
scenario. Therefore, the doorbell timeout is increased.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When the system is shut down, the process is killed, but the
accelerator device does not stop executing the tasks. If the
accelerator device still accesses the memory and writes back data
to the memory after the memory is reclaimed by the system,
an NFE error may occur. Therefore, before the system is shut
down, the driver needs to stop the device and write data back
to the memory.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Before removing the driver, flush inter-function communication
work, and subsequent communication work is not processed.
This prevents communication threads from accessing released memory.

Fixes: ("crypto: hisilicon/qm - enable PF and VFs communication")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove flag HASH_FLAGS_DMA_READY as it can put the driver in a deadlock
state.
If the DMA automatically set the DCAL bit, the interrupt indicating the
end of a computation can be raised before the DMA complete sequence.
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If IP has MDMAT support, set or reset the bit MDMAT in Control Register.

Fixes: b56403a2 ("crypto: stm32/hash - Support Ux500 hash")
Cc: stable@vger.kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When we are sending the data to HASH with the DMA, we send all the data
provided in the scatterlists of the request.
But in some cases (ex : tcrypt performances tests), we should only send
req->nbytes
When iterating through the scatterlist we verify if it is the last
scatterlist or if the number of bytes sent plus the data of the current
scatterlist is superior of the total number of bytes to hash.
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

We were reading the length of the scatterlist sg after copying value of
tsg inside.
So we are using the size of the previous scatterlist and for the first
one we are using an unitialised value.
Fix this by copying tsg in sg[0] before reading the size.

Fixes : 8a1012d3 ("crypto: stm32 - Support for STM32 HASH module")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Commit "crypto: stm32 - Fix empty message processing" remove the use of
the argument bufcnt in stm32_hash_write_ctrl.
Hence, we can remove it from the function prototype and simplify the
function declaration.
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add the all SHA-2 (up to 512) and SHA-3 algorithm support.
Update compatible table to add stm32mp13.
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add a new compatible for stm32mp13 support.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use dev_err_probe to print the error message after a failed hwrng
registration.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

We have no device-specific data for silex-insight,ba431-rng. There's no
need to set .data = NULL, this is the default.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Do not set drvdata in the ba431 driver. Nobody is using it.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Call devm_hwrng_register for device managed registration of the
ingenic-trng driver. ingenic_trng_remove can then be deleted.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

There's no need to disable the rng in ingenic_trng_remove.

The driver's init function sets the CFG_GEN_EN bit to enable the
rng. The cleanup function clears CFG_GEN_EN to revert this.

The remove function calls hwrng_unregister. If the ingenic-trng is not
the current rng at this point, CFG_GEN_EN has already been cleared. If
the ingenic-trng is the current rng, drop_current_rng will call the
cleanup function.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use dev_err_probe in error paths to make the code a bit shorter.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use devm_clk_get_enabled in the ingenic-trng driver. We don't have to
disable and unprepare the clock any more in error paths or in the remove
function.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Don't assign a value to ret if we're about to return from the probe
function and ret's value is not used.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove two defines which are not used in the ingenic-trng driver's code.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Enable compile testing for the ingenic-trng driver.

Remove the dependency on HW_RANDOM. The ingenic-trng config section is
under "if HW_RANDOM".
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The private key of the curve key size generated by stdrng, which maybe
not less than n. Therefore, the private key with the curve key size
minus 1 is generated to ensure that the private key is less than n.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The probe function enables the TRNG hardware before registering the
driver. If registration fails, probe returns an error, but the TRNG
remains enabled.

Define init and cleanup functions, enable and disable the hardware there.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove some unused defines and fix the indentation.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use devm_clk_get_enabled in the pic32 driver. Ensure that the clock is
enabled as long as the driver is registered with the hwrng core.

Fixes: 7ea39973 ("hwrng: pic32 - Use device-managed registration API")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Enable compile testing for the pic32 driver.

Remove the dependency on HW_RANDOM. The pic32 config section is under
"if HW_RANDOM".
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

SIMPLE_DEV_PM_OPS is deprecated, replace it with DEFINE_SIMPLE_DEV_PM_OPS
and use pm_sleep_ptr for setting the driver's pm routines. We can now
remove the __maybe_unused qualifier in the suspend and resume functions.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Simplify the code by calling dev_err_probe instead of dev_err and return.

While at it, use the same device for all error messages.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Rouven Czerwinski <r.czerwinskis@pengutronix.de>
Reviewed-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Mark UWORD_CPYBUF_SIZE with U suffix to make its type the same
with words_num. Then replace the if statement with min() in
qat_uclo_wr_uimage_raw_page() to make code shorter.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: You Kangren <youkangren@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use dev_err_probe to print a message and return an error. This makes the
code a tiny bit shorter.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>