- 11 Mar, 2021 29 commits
-
-
Alexandru Ardelean authored
If we want to merge the attributes of the buffer/ and scan_elements/ directories, we'll need to count all attributes first, then (depending on the attribute group) either allocate 2 attribute groups, or a single one. Historically an IIO buffer was described by 2 subdirectories under /sys/bus/iio/iio:devicesX (i.e. buffer/ and scan_elements/); these subdirs were actually 2 separate attribute groups on the iio_buffer object. Moving forward, if we want to allow more than one buffer per IIO device, keeping 2 subdirectories for each IIO buffer is a bit cumbersome (especially for userpace ABI). So, we will merge the attributes of these 2 subdirs under a /sys/bus/iio/iio:devicesX/bufferY subdirectory. To do this, we need to count all attributes first, and then distribute them based on which buffer this is. For the first buffer, we'll need to also allocate the legacy 2 attribute groups (for buffer/ and scan_elements/), and also a /sys/bus/iio/iio:devicesX/buffer0 attribute group. For buffer1 and above, just a single attribute group will be allocated (the merged one). Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Link: https://lore.kernel.org/r/20210215104043.91251-12-alexandru.ardelean@analog.comSigned-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Alexandru Ardelean authored
Up until now, the device groups that an IIO device had were limited to 6. Two of these groups would account for buffer attributes (the buffer/ and scan_elements/ directories). Since we want to add multiple buffers per IIO device, this number may not be enough, when adding a second buffer. So, this change reallocates the groups array whenever an IIO device group is added, via a iio_device_register_sysfs_group() helper. This also means that the groups array should be assigned to 'indio_dev.dev.groups' really late, right before {cdev_}device_add() is called to do the entire setup. And we also must take care to free this array when the sysfs resources are being cleaned up. With this change we can also move the 'groups' & 'groupcounter' fields to the iio_dev_opaque object. Up until now, this didn't make a whole lot of sense (especially since we weren't sure how multibuffer support would look like in the end). But doing it now kills one birds with one stone. An alternative, would be to add a configurable Kconfig symbol CONFIG_IIO_MAX_BUFFERS_PER_DEVICE (or something like that) and compute a static maximum of the groups we can support per IIO device. But that would probably annoy a few people since that would make the system less configurable. Signed-off-by: -
Alexandru Ardelean authored
Oddly enough the noop function is an int-return. This one seems to be void. This change converts it to int, because we want to change how groups are registered. With that change this function could error out with -ENOMEM. Signed-off-by:
-
Alexandru Ardelean authored
We only need a chardev if we need to support buffers and/or events. With this change, a chardev will be created only if an IIO buffer is attached OR an event_interface is configured. Otherwise, no chardev will be created, and the IIO device will get registered with the 'device_add()' call. Quite a lot of IIO devices don't really need a chardev, so this is a minor improvement to the IIO core, as the IIO device will take up (slightly) fewer resources. In order to not create a chardev, we mostly just need to not initialize the indio_dev->dev.devt field. If that is un-initialized, cdev_device_add() behaves like device_add(). This change has a small chance of breaking some userspace ABI, because it removes un-needed chardevs. While these chardevs (that are being removed) have always been unusable, it is likely that some scripts may check their existence (for whatever logic). And we also hope that before opening these chardevs, userspace would have already checked for some pre-conditions to make sure that opening these chardevs makes sense. For the most part, there is also the hope that it would be easier to change userspace code than revert this. But in the case that reverting this is required, it should be easy enough to do it. Signed-off-by:
-
Alexandru Ardelean authored
Currently, only the 'i' 0x90 ioctl() actually exists and is defined in 'include/uapi/linux/iio/events.h'. It's the IIO_GET_EVENT_FD_IOCTL, which is used to retrieve and FD for reading events from an IIO device. We will want to add more ioct() numbers, so with this change the 'i' 0x90-0x9F space is reserved for IIO ioctl() calls. Signed-off-by:
-
Alexandru Ardelean authored
This change does a conversion of the devm_iio_dmaengine_buffer_alloc() to devm_iio_dmaengine_buffer_setup(). This will allocate an IIO DMA buffer and attach it to the IIO device, similar to devm_iio_triggered_buffer_setup() (though the underlying code is different, the final logic is the same). Since the only user of the devm_iio_dmaengine_buffer_alloc() was the adi-axi-adc driver, this change does the replacement in a single go in the driver. Signed-off-by:
-
Alexandru Ardelean authored
At this point all drivers should use devm_iio_kfifo_buffer_setup() instead of manually allocating via devm_iio_kfifo_allocate() and assigning ops and modes. With this change, the devm_iio_kfifo_allocate() will be made private to the IIO core, since all drivers should call either devm_iio_kfifo_buffer_setup() or devm_iio_triggered_buffer_setup() to create a kfifo buffer. Signed-off-by:
-
Alexandru Ardelean authored
This change makes use of the devm_iio_kfifo_buffer_setup() helper, however the unwind order is changed. The life-time of the kfifo object is attached to the parent device object. This is to make the driver a bit more consistent with the other IIO drivers, even though (as it is now before this change) it shouldn't be a problem. Signed-off-by:
-
Alexandru Ardelean authored
All drivers that already call devm_iio_kfifo_allocate() & iio_device_attach_buffer() are simple to convert to iio_device_attach_kfifo_buffer() in a single go. This change does that; the unwind order is preserved. What is important, is that the devm_iio_kfifo_buffer_setup() be called after the indio_dev->modes is assigned, to make sure that INDIO_BUFFER_SOFTWARE flag is set and not overridden by the assignment to indio_dev->modes. Also, the INDIO_BUFFER_SOFTWARE has been removed from the assignments of 'indio_dev->modes' because it is set by devm_iio_kfifo_buffer_setup(). Signed-off-by:
Gwendal Grignou <gwendal@chromium.org> Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>x Link: https://lore.kernel.org/r/20210215104043.91251-4-alexandru.ardelean@analog.comSigned-off-by:
-
Alexandru Ardelean authored
This change adds the devm_iio_kfifo_buffer_setup() helper/short-hand, which groups the simple routine of allocating a kfifo buffers via devm_iio_kfifo_allocate() and calling iio_device_attach_buffer(). The mode_flags parameter is required, as the IIO kfifo supports 2 modes: INDIO_BUFFER_SOFTWARE & INDIO_BUFFER_TRIGGERED. The setup_ops parameter is optional. This function will be a bit more useful when needing to define multiple buffers per IIO device. The naming for this function has been inspired from iio_triggered_buffer_setup() since that one does a kfifo alloc + a pollfunc alloc. So, this should have a more familiar ring to what it is. Signed-off-by:
-
Lars-Peter Clausen authored
The IIO core provides a function to do formatting of fixedpoint numbers. In the past there have been some issues with the implementation of the function where for example negative numbers were not handled correctly. Introduce a basic unit test based on kunit that tests the function and ensures that the generated output matches the expected output. This gives us some confidence that future modifications to the function implementation will not break ABI compatibility. To run the unit tests follow the kunit documentation and add CONFIG_IIO=y CONFIG_IIO_TEST_FORMAT=y to the .kunitconfig and run > ./tools/testing/kunit/kunit.py run Configuring KUnit Kernel ... Building KUnit Kernel ... Starting KUnit Kernel ... ============================================================ ======== [PASSED] iio-format ======== [PASSED] iio_test_iio_format_value_integer [PASSED] iio_test_iio_format_value_fixedpoint [PASSED] iio_test_iio_format_value_fractional [PASSED] iio_test_iio_format_value_fractional_log2 [PASSED] iio_test_iio_format_value_multiple ============================================================ Testing complete. 21 tests run. 0 failed. 0 crashed. Elapsed time: 8.242s total, 0.001s configuring, 3.865s building, 0.000s running Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Link: https://lore.kernel.org/r/20201215191743.2725-3-lars@metafoo.deSigned-off-by:
-
Lars-Peter Clausen authored
When formatting a value using IIO_VAL_FRACTIONAL_LOG2 and the values is between -1 and 0 the sign is omitted. We need the same trick as for IIO_VAL_FRACTIONAL to make sure this gets formatted correctly. Signed-off-by:
-
Lars-Peter Clausen authored
IIO_VAL_FRACTIONAL_LOG2 works with signed values, yet the temporary we use is unsigned. This works at the moment because the variable is implicitly cast to signed everywhere where it is used. But it will certainly be cleaner to use a signed variable in the first place. Signed-off-by:
-
Bhaskar Chowdhury authored
s/postive/positive/ Signed-off-by:
Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by:
Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20210210085704.1228068-1-unixbhaskar@gmail.comSigned-off-by:
-
Hans de Goede authored
Some 2-in-1 laptops / convertibles with 360° (yoga-style) hinges, use 2 KXCJ91008 accelerometers: 1 in their display using an ACPI HID of "KIOX010A"; and 1 in their base using an ACPI HID of "KIOX020A" Since in this case we know the location of each accelerometer, set the label for the accelerometers to the standardized "accel-display" resp. "accel-base" labels. This way userspace can use the labels to get the location. This was tested on a Medion Akoya E2228T MD60250. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210207160901.110643-4-hdegoede@redhat.comSigned-off-by:
-
Hans de Goede authored
Some 2-in-1 laptops / convertibles with 360° (yoga-style) hinges, use 2 bmc150 accelerometers, defined by a single BOSC0200 ACPI device node (1 in their base and 1 in their display). Since in this case we know the location of each accelerometer, set the label for the accelerometers to the standardized "accel-display" resp. "accel-base" labels. This way userspace can use the labels to get the location. This was tested on a Lenovo ThinkPad Yoga 11e 4th gen (N3450 CPU). Signed-off-by:
-
Hans de Goede authored
Only set indio_dev->label from of/dt if there actually is a label specified in of. This allows drivers to set a label without this being overwritten with NULL when there is no label specified in of. This is esp. useful on devices where of is not used at all, such as your typical x86/ACPI device. Signed-off-by:
-
Tomislav Denis authored
Add a device tree binding documentation for Texas Instruments ADS131E0x ADC family driver. Signed-off-by:
Tomislav Denis <tomislav.denis@avl.com> Reviewed-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210202084107.3260-3-tomislav.denis@avl.comSigned-off-by:
-
Tomislav Denis authored
The ADS131E0x are a family of multichannel, simultaneous sampling, 24-bit, delta-sigma, analog-to-digital converters (ADCs) with a built-in programmable gain amplifier (PGA), internal reference and an onboard oscillator. Datasheet: https://www.ti.com/lit/ds/symlink/ads131e08.pdfSigned-off-by:
-
Mike Looijmans authored
The BMI088 is a combined module with both accelerometer and gyroscope. This adds the accelerometer driver support for the SPI interface. The gyroscope part is already supported by the BMG160 driver. Signed-off-by:
Mike Looijmans <mike.looijmans@topic.nl> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210125150732.23873-2-mike.looijmans@topic.nlSigned-off-by:
-
Mike Looijmans authored
This adds the device-tree bindings for the Bosch Sensortec BMI088 IMU, the accelerometer part. Signed-off-by:
-
zuoqilin authored
change 'regster' to 'register' Signed-off-by:
zuoqilin <zuoqilin@yulong.com> Link: https://lore.kernel.org/r/20210128021905.963-1-zuoqilin1@163.comSigned-off-by:
-
Peter Meerwald-Stadler authored
Haven't had much time lately and moved on to different things. Thanks Jonathan for the gentle introduction to Linux land. Signed-off-by:
Peter Meerwald-Stadler <pmeerw@pmeerw.net> Reviewed-by:
Matt Ranostay <matt.ranostay@konsulko.com> Link: https://lore.kernel.org/r/20210125195654.580465-1-pmeerw@pmeerw.netSigned-off-by:
-
Ahmad Fatoum authored
For non-DMA usage, we have an easy way to associate a timestamp with a sample: iio_pollfunc_store_time stores a timestamp in the primary trigger IRQ handler and stm32_adc_trigger_handler runs in the IRQ thread to push out the buffer along with the timestamp. For this to work, the driver needs to register an IIO_TIMESTAMP channel. Do this. For DMA, it's not as easy, because we don't push the buffers out of stm32_adc_trigger, but out of stm32_adc_dma_buffer_done, which runs in a tasklet scheduled after a DMA completion. Preferably, the DMA controller would copy us the timestamp into that buffer as well. Until this is implemented, restrict timestamping support to only PIO. For low-frequency sampling, PIO is probably good enough. Cc: Holger Assmann <has@pengutronix.de> Acked-by:
Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by:
Ahmad Fatoum <a.fatoum@pengutronix.de> Link: https://lore.kernel.org/r/20210125194824.30549-1-a.fatoum@pengutronix.deSigned-off-by:
-
Ye Xiang authored
Because the data of HID_USAGE_SENSOR_ORIENT_QUATERNION defined by ISH FW is s16, but quaternion data type is in_rot_quaternion_type(le:s16/32X4>>0), need to transform data type from s16 to s32 May require manual backporting. Fixes: fc18dddc ("iio: hid-sensors: Added device rotation support") Signed-off-by:
Ye Xiang <xiang.ye@intel.com> Link: https://lore.kernel.org/r/20210130102546.31397-1-xiang.ye@intel.com Cc: <Stable@vger.kernel.org> Signed-off-by:
-
William Breathitt Gray authored
The IIO counter driver has been superseded by the Counter subsystem as discussed in [1]. This patch removes the IIO counter ABI from the 104-QUAD-8 driver. [1] https://lore.kernel.org/lkml/20210119104105.000010df@Huawei.com/ Cc: Syed Nayyar Waris <syednwaris@gmail.com> Signed-off-by:
William Breathitt Gray <vilhelm.gray@gmail.com> Link: https://lore.kernel.org/r/98a39983d5df761c058a469d1346fd8ffdef8516.1611973018.git.vilhelm.gray@gmail.comSigned-off-by:
-
Fabrice Gasnier authored
Currently, the STM32 LP Timer counter driver registers into both IIO and counter subsystems, which is redundant. Remove the IIO counter ABI and IIO registration from the STM32 LP Timer counter driver since it's been superseded by the Counter subsystem as discussed in [1]. Keep only the counter subsystem related part. Move a part of the ABI documentation into a driver comment. This also removes a duplicate ABI warning $ scripts/get_abi.pl validate ... /sys/bus/iio/devices/iio:deviceX/in_count0_preset is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-timer-stm32:100 ./Documentation/ABI/testing/sysfs-bus-iio-lptimer-stm32:0 [1] https://lkml.org/lkml/2021/1/19/347Acked-by:
-
Jonathan Cameron authored
Seems that there are config combinations in which this driver gets enabled and hence selects the MFD, but with out HAS_IOMEM getting pulled in via some other route. MFD is entirely contained in an if HAS_IOMEM block, leading to the build issue in this bugzilla. https://bugzilla.kernel.org/show_bug.cgi?id=209889 Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Ahmad Fatoum authored
s/timetamping/timestamping/ Cc: trivial@kernel.org Signed-off-by:
-
- 10 Mar, 2021 11 commits
-
-
Klemen Košir authored
This patch removes some repeated words in code comments. Signed-off-by:
Klemen Košir <klemen.kosir@kream.io> Link: https://lore.kernel.org/r/20210303090134.16007-1-klemen.kosir@kream.ioSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Song Chen authored
visornic uses timer to check the response queue and drain it if needed periodically. On the other hand, visorbus provides periodic work to serve such request, therefore, timer should be replaced by channel_interrupt. Signed-off-by:
Song Chen <chensong_2000@189.cn> Link: https://lore.kernel.org/r/1610439940-5590-1-git-send-email-chensong_2000@189.cnSigned-off-by:
-
Kumar Kartikeya Dwivedi authored
Instead, depend on the size of the destination buffer for easier refactoring. Signed-off-by:
Kumar Kartikeya Dwivedi <memxor@gmail.com> Link: https://lore.kernel.org/r/20210221154258.119503-1-memxor@gmail.comSigned-off-by:
-
Gustavo A. R. Silva authored
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. Use flexible-array member in struct ndis_802_11_var_ie, instead of one-element array. Also, this helps with the ongoing efforts to enable -Warray-bounds by fixing the following warning: drivers/staging/rtl8188eu/core/rtw_wlan_util.c: In function ‘HT_caps_handler’: drivers/staging/rtl8188eu/core/rtw_wlan_util.c:665:65: warning: array subscript 2 is above array bounds of ‘u8[1]’ {aka ‘unsigned char[1]’} [-Warray-bounds] 665 | if ((pmlmeinfo->HT_caps.ampdu_params_info & 0x3) > (pIE->data[i] & 0x3)) | ~~~~~~~~~^~~ [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays Link: https://github.com/KSPP/linux/issues/79 Link: https://github.com/KSPP/linux/issues/109Signed-off-by:Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/20210304020228.GA45139@embeddedorSigned-off-by:
-
Marco Cesati authored
This commit fixes the following checkpatch.pl warnings: WARNING: do not add new typedefs #24: FILE: hal/HalBtc8723b1Ant.h:24: +typedef enum _BT_INFO_SRC_8723B_1ANT { WARNING: do not add new typedefs #31: FILE: hal/HalBtc8723b1Ant.h:31: +typedef enum _BT_8723B_1ANT_BT_STATUS { WARNING: do not add new typedefs #41: FILE: hal/HalBtc8723b1Ant.h:41: +typedef enum _BT_8723B_1ANT_WIFI_STATUS { WARNING: do not add new typedefs #51: FILE: hal/HalBtc8723b1Ant.h:51: +typedef enum _BT_8723B_1ANT_COEX_ALGO { WARNING: do not add new typedefs #66: FILE: hal/HalBtc8723b1Ant.h:66: +typedef struct _COEX_DM_8723B_1ANT { WARNING: do not add new typedefs #121: FILE: hal/HalBtc8723b1Ant.h:121: +typedef struct _COEX_STA_8723B_1ANT { Signed-off-by:Marco Cesati <marco.cesati@gmail.com> Link: https://lore.kernel.org/r/20210305100146.30687-1-marco.cesati@gmail.comSigned-off-by:
-
Marco Cesati authored
This commit fixes the following checkpatch.pl warnings: WARNING: do not add new typedefs #19: FILE: hal/HalBtc8723b2Ant.h:19: +typedef enum _BT_INFO_SRC_8723B_2ANT { WARNING: do not add new typedefs #26: FILE: hal/HalBtc8723b2Ant.h:26: +typedef enum _BT_8723B_2ANT_BT_STATUS { WARNING: do not add new typedefs #36: FILE: hal/HalBtc8723b2Ant.h:36: +typedef enum _BT_8723B_2ANT_COEX_ALGO { WARNING: do not add new typedefs #51: FILE: hal/HalBtc8723b2Ant.h:51: +typedef struct _COEX_DM_8723B_2ANT { WARNING: do not add new typedefs #104: FILE: hal/HalBtc8723b2Ant.h:104: +typedef struct _COEX_STA_8723B_2ANT { Signed-off-by: -
Denis Efremov authored
IS_MCAST(pstat->hwaddr) checked twice in a row in odm_RefreshRateAdaptiveMaskCE(). Remove the second check. Signed-off-by:
Denis Efremov <efremov@linux.com> Link: https://lore.kernel.org/r/20210305155001.61951-1-efremov@linux.comSigned-off-by:
-
Marco Cesati authored
This commit fixes the following checkpatch.pl warnings: WARNING: do not add new typedefs #11: FILE: hal/HalPhyRf.h:11: +typedef enum _SPUR_CAL_METHOD { WARNING: do not add new typedefs #16: FILE: hal/HalPhyRf.h:16: +typedef enum _PWRTRACK_CONTROL_METHOD { WARNING: do not add new typedefs #27: FILE: hal/HalPhyRf.h:27: +typedef struct _TXPWRTRACK_CFG { Signed-off-by: -
Fabio Aiuto authored
Removed conditional code block checked by unused CONFIG_TX_BCAST2UNI This patch does the cleaning required in TODO file: find and remove code blocks guarded by never set CONFIG_FOO defines Signed-off-by:
Fabio Aiuto <fabioaiuto83@gmail.com> Link: https://lore.kernel.org/r/20210305191713.GA2466@agape.jhsSigned-off-by:
-
Michael Straube authored
Rename parameters of odm_phy_status_query() to avoid camel case. pDM_Odm -> dm_odm pPhyInfo -> phy_info pPhyStatus -> phy_status pPktinfo -> pkt_info Signed-off-by:
Michael Straube <straube.linux@gmail.com> Link: https://lore.kernel.org/r/20210306081133.1272-2-straube.linux@gmail.comSigned-off-by:
-
Michael Straube authored
Rename ODM_PhyStatusQuery() to odm_phy_status_query() to avoid camel case. Signed-off-by:
-
