Signed-off-by: Roman Kagan <rkagan@mail.ru>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>

Match it up to what RFC2414 really specifies.
Noticed by Rick Jones.
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Oliver Dawid <oliver@helios.de>

we found a bug in net/appletalk/ddp.c concerning broadcast packets. In 
kernel 2.4 it was working fine. The bug first occured 4 years ago when 
switching to new SNAP layer handling. This bug can be splitted up into a 
sending(1) and reception(2) problem:

Sending(1)
In kernel 2.4 broadcast packets were sent to a matching ethernet device 
and atalk_rcv() was called to receive it as "loopback" (so loopback 
packets were shortcutted and handled in DDP layer).

When switching to the new SNAP structure, this shortcut was removed and 
the loopback packet was send to SNAP layer. The author forgot to replace 
the remote device pointer by the loopback device pointer before sending 
the packet to SNAP layer (by calling ddp_dl->request() ) therfor the 
packet was not sent back by underlying layers to ddp's atalk_rcv().

Reception(2)
In atalk_rcv() a packet received by this loopback mechanism contains now 
the (rigth) loopback device pointer (in Kernel 2.4 it was the (wrong) 
remote ethernet device pointer) and therefor no matching socket will be 
found to deliver this packet to. Because a broadcast packet should be 
send to the first matching socket (as it is done in many other protocols 
(?)), we removed the network comparison in broadcast case.

Below you will find a patch to correct this bug. Its diffed to kernel 
2.6.14-rc1
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

We know the thing is at least 2-byte aligned, so take
advantage of that instead of invoking memcmp() which
results in truly horrifically inefficient code because
it can't assume anything about alignment.
Signed-off-by: David S. Miller <davem@davemloft.net>

The following is generated when compiling a
recent (2.6.14-rc2-git5) kernel configured for
ARM, with GCC4. 

  CC      init/main.o
In file included from include/linux/netdevice.h:29,
                 from include/net/sock.h:48,
                 from init/main.c:50:
include/linux/if_ether.h:114: error: array type has incomplete element type

It seems that if CONFIG_SYSCTL is not set, then
the compiler will throw an error due to the definition
of the ether_table[] array

Attached is a solution to the problem
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* Don't bother with proto registering if rose_ndevs is bad.
* Make escape structure more coherent.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>

I have been experimenting with loadable protocol modules, and ran into
several issues with module reference counting.

The first issue was that __module_get failed at the BUG_ON check at
the top of the routine (checking that my module reference count was
not zero) when I created the first socket. When sk_alloc() is called,
my module reference count was still 0. When I looked at why sctp
didn't have this problem, I discovered that sctp creates a control
socket during module init (when the module ref count is not 0), which
keeps the reference count non-zero. This section has been updated to
address the point Stephen raised about checking the return value of
try_module_get().

The next problem arose when my socket init routine returned an error.
This resulted in my module reference count being decremented below 0.
My socket ops->release routine was also being called. The issue here
is that sock_release() calls the ops->release routine and decrements
the ref count if sock->ops is not NULL. Since the socket probably
didn't get correctly initialized, this should not be done, so we will
set sock->ops to NULL because we will not call try_module_get().

While searching for another bug, I also noticed that sys_accept() has
a possibility of doing a module_put() when it did not do an
__module_get so I re-ordered the call to security_socket_accept().
Signed-off-by: Frank Filz <ffilzlnx@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Place them on separate cache lines in SMP to lower memory bouncing
between multiple CPU accessing the device.

     - One part is mostly used on receive path (including
       eth_type_trans()) (poll_list, poll, quota, weight, last_rx,
       dev_addr, broadcast)

     - One part is mostly used on queue transmit path (qdisc)
      (queue_lock, qdisc, qdisc_sleeping, qdisc_list, tx_queue_len)

     - One part is mostly used on xmit path (device)
      (xmit_lock, xmit_lock_owner, priv, hard_start_xmit, trans_start)

'features' is placed outside of these hot points, in a location that
may be shared by all cpus (because mostly read)

name_hlist is moved close to name[IFNAMSIZ] to speedup __dev_get_by_name()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We know the lock is going to be taken.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use iteration instead of recursion.  Fraglists within fraglists
should never occur, so we BUG check this.
Signed-off-by: Daniel Phillips <phillips@istop.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We ignored umask when creating new queues via mq_open (when creating
with open() on mqueue fs it is ok of course).  According to the
specification this a bug.  This trivial patch fixes this.
Signed-off-by: Krzysztof Benedyczak <golbi@mat.uni.torun.pl>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: David S. Miller <davem@davemloft.net>

Fix interrupt test handler by adding check for IRQ assertion in
PCI_STATE register in addition to the status block updated bit.

Add test for valid ethernet address in tg3_set_mac_addr().

Add tg3_bus_string() to setup the PCI bus speed/width string for all
PCI/PCIX/PCI Express devices. This is used to print the bus type
during init_one().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix 5780 PHY related problems:

1. MAC_RX_MODE reset must be done before setting up the MAC_MODE
   register on 5705_PLUS chips or the chip will stop receiving after
   a while. The MAC_RX_MODE reset is needed to prevent intermittently
   losing the first receive packet on serdes chips.

2. Skip MAC loopback test on 5780 because of hardware errata. Normal
   traffic including PHY loopback is not affected by the errata.

3. PHY loopback fails intermittently on 5708S and this is fixed by
   putting the PHY in loopback mode first before programming the MAC
   mode register. A MAC_RX_MODE reset is also added.

4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow
   nway_reset if 5780S is in parallel detect mode.

5. Add missing PHY IDs in KNOWN_PHY_ID() macro.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we double-add a neighbour entry timer, which should be
impossible but has been reported, dump the current state of
the entry so that we can debug this.
Signed-off-by: David S. Miller <davem@davemloft.net>

	arm maketools needs include/asm-arm in place in the build tree.
On normal builds it's always there, of course, but on O= it's created
(by generic code) too late - when we get to asm-offset.h.

	We used to get away with that by accident - creation of
include/asm-arm/arch symlink creates include/asm-arm and it happened
to go before maketools.  However, we did not have such dependency,
so that luck didn't last - now maketools is picked first and we are screwed.

	Both the symlink and maketools are prerequisites of the same
target (archprepare).  This fix is obvious - make the latter explicitly
depend on the former and be done with that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We do _not_ need "sparse" in sparse arguments ;-)

What we do need is __BIG_ENDIAN__; right now unconditional, when m32r
starts using CPU_LITTLE_ENDIAN, we'll need to adjust.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

	Most of these guys are simply not needed (pulled by other stuff
via asm-i386/hardirq.h).  One that is not entirely useless is hilarious -
arch/i386/oprofile/nmi_timer_int.c includes linux/irq.h... as a way to
get linux/errno.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

In order to do it correctly on UltraSPARC-III+ and later we'd
need to add some complicated code to set the TAG access extension
register before loading the TLB.

Since this optimization gives questionable gains, it's best to
just remove it for now instead of adding the fix for Ultra-III+
Signed-off-by: David S. Miller <davem@davemloft.net>

It tries to batch up the tag loads and comparisons, and
then the stores.  And this is just complicated instead
of efficient.

Also, make the symbol of the Cheetah version more grepable.
Signed-off-by: David S. Miller <davem@davemloft.net>

When you've enabled conntrack and NAT as a module (standard case in all
distributions), and you've also enabled the new conntrack netlink
interface, loading ip_conntrack_netlink.ko will auto-load iptable_nat.ko.
This causes a huge performance penalty, since for every packet you iterate
the nat code, even if you don't want it.

This patch splits iptable_nat.ko into the NAT core (ip_nat.ko) and the
iptables frontend (iptable_nat.ko).  Threfore, ip_conntrack_netlink.ko will
only pull ip_nat.ko, but not the frontend.  ip_nat.ko will "only" allocate
some resources, but not affect runtime performance.

This separation is also a nice step in anticipation of new packet filters
(nf-hipac, ipset, pkttables) being able to use the NAT core.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These broke existing apps, and the checks are superfluous
as the values being verified aren't even used.
Signed-off-by: David S. Miller <davem@davemloft.net>

> Steps to reproduce:
> 1. Boot Linux, do NOT setup any IPv6 routes
> 2. ip route get 2001::1 (or any unroutable address)

Well caught.  We never set rt6i_idev on ip6_null_entry.
This patch should make the problem go away.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If input message rate from userspace is too high, do not drop them,
but try to deliver using work queue allocation.

Failing there is some kind of congestion control.

It also removes warn_on on this condition, which scares people.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's on the stack and declared as "unsigned char[]", but pointers
and similar can be in here thus we need to give it an explicit
alignment attribute.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Patch from Vincent Sanders

A recent patch which made IXP4xx mach_desc's depend on config options
had the effect of not building the kernel for several machines it
possibly could be, this patch updates the default config to ensure all
possible machines are built for by default.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from David Vrabel
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>