error_module is 5 bits wide not 4.  The corresponding crit_error_count
array is correct with 32 entries.
Signed-off-by: Chien Tung <ctung@neteffect.com>
--
 drivers/infiniband/hw/nes/nes_hw.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Fix routed RDMA connections to destinations where the next hop is not
the final destination.  Use neigh_*() to properly locate neighbor.
Signed-off-by: Bob Sharp <bsharp@neteffect.com>
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>

Change management of perfect filter table to allow enhanced
performance applications.
Signed-off-by: Vadim Makhervaks <vmakhervaks@neteffect.com>
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Handle async error NES_AEQE_AEID_AMP_BOUNDS_VIOLATION.
Signed-off-by: Faisal Latif <flatif@neteffect.com>
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Mask off a critical error after 100 critical error interrupts to
keep the system "sane".
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Mask off MAC interrupts on netdev_stop to prevent spurious MAC interrupts
on unload/reload of iw_nes.
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Fill in firmware version for ethtool_drvinfo.
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Use timer value set via ethtool intead of #defines.
Signed-off-by: John Lacombe <jlacombe@neteffect.com>
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Use correct define for max TSO fragments.
Signed-off-by: Bob Sharp <bsharp@neteffect.com>
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Re-enable multicast and unicast after changing MTU.
Signed-off-by: Bob Sharp <bsharp@neteffect.com>
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Signed-off-by: Bob Sharp <bsharp@neteffect.com>
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Clear MDC bits before setting them to a new value.  Adjust MDC value
for 10G.
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Add a module parameter wqm_quanta.  It controls the number of segments
transmitted at a time.
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Change permission to 0644 so root can set mpa_version, disable_mpa_crc,
send_first, and nes_drv_opt at runtime.
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Add support for NetEffect 4 port 1G HP blade card.  The mapping
between physical port and MAC is different from the standup card.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Signed-off-by: Faisal Latif <flatif@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] cio: fix orb initialization in cio_start_key
  [S390] cio: Fix driver_data handling for ccwgroup devices.

* git://oss.sgi.com:8090/xfs/linux-2.6:
  [XFS] Don't do I/O beyond eof when unreserving space
  [XFS] Fix use-after-free with buffers
  [XFS] Prevent lockdep false positives when locking two inodes.
  [XFS] Fix barrier status change detection.
  [XFS] Prevent direct I/O from mapping extents beyond eof
  [XFS] Fix regression introduced by remount fixup
  [XFS] Move memory allocations for log tracing out of the critical path

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB: Fix deadlock on RTNL between bcast join comp and ipoib_stop()
  RDMA/nes: Fix client side QP destroy
  IB/mlx4: Fix up fast register page list format
  mlx4_core: Set RAE and init mtt_sz field in FRMR MPT entries

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: fix deadlock in setting scheduler parameter to zero
  sched: fix 2.6.27-rc5 couldn't boot on tulsa machine randomly

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clockevents: make device shutdown robust
  clocksource, acpi_pm.c: fix check for monotonicity
  clockevents: remove WARN_ON which was used to gather information

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: completely disable NOPL on 32 bits
  x86/paravirt: Remove duplicate paravirt_pagetable_setup_{start, done}()
  xen: fix for xen guest with mem > 3.7G
  x86: fix possible x86_64 and EFI regression
  arch/x86/kernel/kdebugfs.c: introduce missing kfree

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  Fix compile failure with non modular builds
  powerpc: Holly board needs dtbImage target
  powerpc: Fix interrupt values for DMA2 in MPC8610 HPCD device tree

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5255/1: Update jornada ssp to remove build errors/warnings
  [ARM] omap: back out 'internal_clock' support
  [ARM] 5249/1: davinci: remove redundant check in davinci_psc_config()

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: nmi_enter() without nmi_exit()
  avr32: fix sys_sync_file_range() call convention
  avr32: add generic_find_next_le_bit bit function
  avr32: add .gitignore files
  atstk1000: fix build breakage with BOARD_ATSTK100X_SW2_CUSTOM=y

* 'for-linus' of git://neil.brown.name/md:
  md: Don't wait UNINTERRUPTIBLE for other resync to finish

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix SMP bootup with CONFIG_STACK_DEBUG or ftrace.
  sparc64: Fix OOPS in psycho_pcierr_intr_other().

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  e100: Use pci_pme_active to clear PME_Status and disable PME#
  e1000: prevent corruption of EEPROM/NVM
  forcedeth: call restore mac addr in nv_shutdown path
  bnx2: Promote vector field in bnx2_irq structure from u16 to unsigned int
  sctp: Fix oops when INIT-ACK indicates that peer doesn't support AUTH
  sctp: do not enable peer features if we can't do them.
  sctp: set the skb->ip_summed correctly when sending over loopback.
  udp: Fix rcv socket locking

While updating the rcu code, I noticed that do_nmi() for AVR32 is odd:
There is an nmi_enter() call without an nmi_exit().
This can't be correct, it breaks rcu (at least the preempt version) and
lockdep.

[haavard.skinnemoen@atmel.com: fixed another case that returned directly]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>

On AVR32, all parameters beyond the 5th are passed on the stack. System
calls don't use the stack -- they borrow a callee-saved register
instead. This means that syscalls that take 6 parameters must be called
through a stub that pushes the last parameter on the stack.

This patch adds a stub for sync_file_range syscall on AVR32
architecture.  Tested with uClibc snapshot.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>

This patch implements the generic_find_next_le_bit bit function for AVR32
architecture. This is used by EXT4 file system.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>

Ignore Kernel binaries, kernel/vmlinux.lds and a log file.
Signed-off-by: Markus Heidelberg <markus.heidelberg@web.de>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>

The #ifdef surrounding the code adding the mmc controller had a typo,
causing it to be compiled even when mmc was supposed to be disabled.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>

When two md arrays share some block device (e.g each uses different
partitions on the one device), a resync of one array will wait for
the resync on the other to finish.

This can be a long time and as it currently waits TASK_UNINTERRUPTIBLE,
the softlockup code notices and complains.

So use TASK_INTERRUPTIBLE instead and make sure to flush signals
before calling schedule.
Signed-off-by: NeilBrown <neilb@suse.de>

Currently e100 uses pci_enable_wake() to clear pending wake-up events
and disable PME# during intitialization, but that function is not
suitable for this purpose, because it immediately returns error code
if device_may_wakeup() returns false for given device.

Make e100 use pci_pme_active(), which carries out exactly the
required operations, instead.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Andrey reports e1000 corruption, and that a patch in vmware's ESX fixed
it.

The EEPROM corruption is triggered by concurrent access of the EEPROM
read/write. Putting a lock around it solve the problem.

[akpm@linux-foundation.org: use DEFINE_SPINLOCK to avoid confusing lockdep]
Signed-off-by: Christopher Li <chrisl@vmware.com>
Reported-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Zach Amsden <zach@vmware.com>
Cc: Pratap Subrahmanyam <pratap@vmware.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

after

| commit f735a2a1
| Author: Tobias Diedrich <ranma+kernel@tdiedrich.de>
| Date:   Sun May 18 15:02:37 2008 +0200
|
|    [netdrvr] forcedeth: setup wake-on-lan before shutting down
|
|    When hibernating in 'shutdown' mode, after saving the image the suspend hook
|    is not called again.
|    However, if the device is in promiscous mode, wake-on-lan will not work.
|    This adds a shutdown hook to setup wake-on-lan before the final shutdown.
|
|    Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
|    Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

my servers with nvidia ck804 and mcp55 will reverse mac address with kexec.

it turns out that we need to restore the mac addr in nv_shutdown().

[akpm@linux-foundation.org: fix typo in printk]
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The bnx2 driver stores/uses the irq value from the pci_dev internally.
But when it stores the irq value, it has been performing an
integer demotion.  Because of the recent changes made to
arch/x86/kernel/io_apic.c, the new method in creating the irq value
(using build_irq_for_pci_dev()) has exposed this bug on x86 systems.

Because of this demotion when calling request_irq() from
bnx2_request_irq(), the driver would get a return code of -EINVAL.
This is because the kernel could not find the requested irq descriptor.
By storing the irq value properly, the kernel can find the correct
irq descriptor and the bnx2 driver can operate normally.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If INIT-ACK is received with SupportedExtensions parameter which
indicates that the peer does not support AUTH, the packet will be
silently ignore, and sctp_process_init() do cleanup all of the
transports in the association.
When T1-Init timer is expires, OOPS happen while we try to choose
a different init transport.

The solution is to only clean up the non-active transports, i.e
the ones that the peer added.  However, that introduces a problem
with sctp_connectx(), because we don't mark the proper state for
the transports provided by the user.  So, we'll simply mark
user-provided transports as ACTIVE.  That will allow INIT
retransmissions to work properly in the sctp_connectx() context
and prevent the crash.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>