- 11 Dec, 2019 6 commits
-
-
Xiaomeng Hou authored
implement sensor interface of feature mask for debugfs. Signed-off-by:
Xiaomeng Hou <Xiaomeng.Hou@amd.com> Reviewed-by:
Huang Rui <ray.huang@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Xiaomeng Hou authored
implement smu12 get_clk_freq interface to get clock frequency like MCLK/SCLK. Signed-off-by:
-
Xiaomeng Hou authored
add sensor interface of get gpu temperature for debugfs. Signed-off-by:
-
Evan Quan authored
This is needed for coming asic init on performing gpu reset. V2: use non-asic specific programing way Signed-off-by:
Evan Quan <evan.quan@amd.com> Reviewed-by:
-
changzhu authored
It may cause timeout waiting for sem acquire in VM flush when using invalidate semaphore for picasso. So it needs to avoid using invalidate semaphore for piasso. Signed-off-by:
changzhu <Changfeng.Zhu@amd.com> Reviewed-by:
-
Le Ma authored
Switch to baco reset method for ras recovery if the PMFW supported. If not, keep the original reset method. v2: revise the condition Signed-off-by:
Le Ma <le.ma@amd.com> Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by:
-
- 09 Dec, 2019 9 commits
-
-
Evan Quan authored
Abort the message issuing if the SMU was not in the right state. Signed-off-by:
Kenneth Feng <kenneth.feng@amd.com> Signed-off-by:
-
Evan Quan authored
As the check may be done with purpose and the warning output will be confusing. Signed-off-by:
-
Alex Deucher authored
To avoid a compiler warning. Reviewed-by:
Zhan Liu <zhan.liu@amd.com> Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
-
Hawking Zhang authored
this fix the regression caused by asd/ta loading sequence adjustment recently. asd/ta loading was move out from hw_start and should also be applied to psp_resume. otherwise those fw loading will be ignored in resume phase. v2: add the mutex unlock for asd loading failure case v3: merge the error handling to failed tag Signed-off-by:
Guchun Chen <guchun.chen@amd.com> Reviewed-by:
-
Thong Thai authored
This reverts commit a4840d91. Reverting due to power efficiency issues seen on Raven 1 and 2 when DPG mode is enabled. Signed-off-by:
Thong Thai <thong.thai@amd.com> Reviewed-by:
-
Christian König authored
This allows to invalidate VM entries without taking the reservation lock. v3: use -EBUSY Signed-off-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by:
-
Christian König authored
Don't add the VM update fences to the resv object and remove the handling to stop implicitely syncing to them. Ongoing updates prevent page tables from being evicted and we manually block for all updates to complete before releasing PDs and PTS. This way we can do updates even without the resv obj locked. Signed-off-by:
-
Christian König authored
Allows us to reduce the overhead while syncing to fences a bit. v2: also drop adev parameter from the functions Signed-off-by:
-
Christian König authored
When a page tables needs to be evicted the VM code should decide if that is possible or not. Signed-off-by:
-
- 06 Dec, 2019 1 commit
-
-
Andrey Grodzovsky authored
BACO feature must be kept enabled to allow entry into BACO state in SMU during runtime suspend. Signed-off-by:
Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by:
-
- 05 Dec, 2019 24 commits
-
-
Nicholas Kazlauskas authored
[Why] To quickly validate whether DMCUB is running and accepting commands for offload testing we want to intercept a common sequence as part of modeset programming. [How] OTG enable will cause the most impact in terms of golden register changes and it's a single register write. This approach was previously done in dcn10 code when it was shared with dcn20 but it wasn't ported over to the dcn20 code. Port over start, execute and wait sequence into dcn20_optc. Signed-off-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by:
Tony Cheng <Tony.Cheng@amd.com> Acked-by:
Leo Li <sunpeng.li@amd.com> Signed-off-by:
-
abdoulaye berthe authored
[Why] When setting lttpr mode, the new mode to bet is not logged properly. [How] Update log message to show the right mode. Signed-off-by:
abdoulaye berthe <abdoulaye.berthe@amd.com> Reviewed-by:
George Shen <George.Shen@amd.com> Acked-by:
-
Dmytro Laktyushkin authored
In preparation for further changes Signed-off-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by:
Chris Park <Chris.Park@amd.com> Acked-by:
-
Yongqiang Sun authored
[Why] It seems always request passive flip on RN due to incorrect compare clock state to determine optization. [How] Instead of calling memcmp, compare clock state member to determine the condition. Signed-off-by:
Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by:
-
George Shen authored
[Why] When a timeout occurs after a DEFER, some devices require more retries than in the case of a regular timeout. [How] In a timeout occurrence, check whether a DEFER has occurred before the timeout and retry MAX_DEFER_RETRIES retries times instead of MAX_TIMEOUT_RETRIES. Signed-off-by:
-
Krunoslav Kovac authored
[Why] Currently we require HDR_MULT >= 1.0 There are scenarios where we need < 1.0 [How] Only guard against 0 - it will black-screen image. It is up to higher-level logic to decide what HDR_MULT values are allowed in each particular case. Signed-off-by:
Krunoslav Kovac <Krunoslav.Kovac@amd.com> Reviewed-by:
Aric Cyr <Aric.Cyr@amd.com> Acked-by:
-
Aric Cyr authored
Signed-off-by:
-
Reza Amini authored
[Why] Need support for more color management in 10bit surface. [How] Provide support for DePQ for 10bit surface Signed-off-by:
Reza Amini <Reza.Amini@amd.com> Reviewed-by:
-
Eric Yang authored
Value obtained from DV is not allowing 8k60 CTA mode with DSC to pass, after checking real value being used in hw, find out that correct value is 3600, which will allow that mode. Signed-off-by:
Eric Yang <Eric.Yang2@amd.com> Reviewed-by:
-
Amanda Liu authored
[Why] Screen tearing is present in tests when setting the frame rate to certain fps [How] Revert previous optimizations for low frame rates. Signed-off-by:
Amanda Liu <amanda.liu@amd.com> Reviewed-by:
-
Aric Cyr authored
[Why] Cursor position needs to take into account plane scaling as well. [How] Translate cursor coords from stream space to plane space. Signed-off-by:
Anthony Koo <Anthony.Koo@amd.com> Acked-by:
-
Anthony Koo authored
[Why] It is causing green Line at the bottom of SDR 480p MPO playback [How] Limit workaround to vertical > 512 Signed-off-by:
-
Wenjing Liu authored
dc needs to expose its internal dsc policy. Signed-off-by:
Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by:
Nikola Cornij <Nikola.Cornij@amd.com> Acked-by:
-
Wenjing Liu authored
[why] add_dsc_to_stream_resource could be called for validation. Failing validation is completely fine. However failing it inside commit streams is bad. This code could be triggered for both contexts. The function itself cannot distinguish the caller, which makes it impossible to output the log only in the meaningful case (commit streams). Signed-off-by:
-
Wenjing Liu authored
[why] Need to support 6 bpp for 420 pixel encoding only. [how] Add a dc function to determine what bpp range can be supported for given pixel encoding. Signed-off-by:
-
Noah Abradjian authored
[Why] I was advised that we don't need this call of program_front_end, as earlier and later calls in the same sequence are sufficient. [How] Remove first call of program_front_end in dc_commit_state_no_check. Signed-off-by:
Noah Abradjian <noah.abradjian@amd.com> Reviewed-by:
-
Noah Abradjian authored
[Why] I was advised that we may need to check for mpcc idle in more cases than just when opp_changed is true. Also, mpcc_inst is equal to pipe_idx, so remove for loop. [How] Remove opp_changed flag check and mpcc_inst loop. Signed-off-by:
-
abdoulaye berthe authored
[Why] When training with repeater the aux read interval must be set to repeater specific aux_red_interval. This value is always 100us for CR. [How] Check for repeater when setting the aux_rd_interval in channel equalization. Use the right offset in the aux_rd_interval array Signed-off-by:
-
Noah Abradjian authored
[Why] MPCC programming was being missed during certain split pipe enables due to full_update flag not being true. This caused a momentary flash on half the screen. After discussion, determined we should not have that flag check within update_mpcc, as it should always perform full programming when called. [How] Remove flag check. We call update_blending within insert_plane, so we do not need to replace its call from the if block. Signed-off-by:
-
Joseph Gravenor authored
[Why] DF team has produced more optimized sr latency numbers, for lpddr4 [How] change the sr laency in the lpddr4 wm table to the new latency number Signed-off-by:
Joseph Gravenor <joseph.gravenor@amd.com> Reviewed-by:
-
Nicholas Kazlauskas authored
[Why] Scratch registers are limited on the DMCUB and we have an expanding list of state to track between driver and DMCUB. [How] Place shared state in cache window 6. The cache window size is aligned to the size of the cache line on the DMCUB to make it easy to invalidate. The shared state is intended to be read only from driver side so it's been marked as const. The use of volatile is intentional. The memory for the shared firmware state is memory mapped from the framebuffer memory. The DMCUB will flush its cache after modifying the region. There's no way for x86 to known whether this data is stale or not so we want to intentionally disable optimization to force the read at every access. Signed-off-by:
-
Nicholas Kazlauskas authored
[Why] Commands will be considered a stable ABI between driver and firmware. Commands are also split between DC commands, DAL feature commands, and VBIOS commands. Commands are currently not designated to a specific ID and the enum does not provide a stable ABI. We currently group all of these into a single command type of 8-bits. With the stable ABI consideration in mind it's not unreasonable to run out of command IDs. For cleaner separation and versioning split the commands into a main type and a subtype. [How] For commands where performance matters (like reg sequences) these are still considered main commands. Sub commands will be split by ownership/feature. Update existing command sequences to reflect new changes. Signed-off-by:
-
Mikita Lipski authored
[why] The function is expected to return instance of the timing generator therefore we shouldn't be returning boolean in integer function, and we shouldn't be returning zero so changing it to -1. Signed-off-by:
Mikita Lipski <mikita.lipski@amd.com> Reviewed-by:
Martin Leung <Martin.Leung@amd.com> Acked-by:
-
Hugo Hu authored
[Why] The link setting will be modify after disable phy and due to DP Compliance Fails. [How] Save and resotre link setting for disable link phy when link retraining. Signed-off-by:
Hugo Hu <hugo.hu@amd.com> Reviewed-by:
-
