Inform drivers about the changed CTS protection settings.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch pushes the "netif_running()" and "same type as before"
checks down into ieee80211_if_change_type() to centralise the
logic instead of duplicating it for cfg80211 and wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch revamps the virtual interface handling and makes the
code much easier to follow. Fewer functions, better names, less
spaghetti code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, almost every interface type has a 'bss' pointer
pointing to BSS information. This BSS information, however,
is for a _local_ BSS, not for the BSS we joined, so having
it on a STA mode interface makes little sense, but now they
have it pointing to the master device, which is an AP mode
virtual interface. However, except for some bitrate control
data, this pointer is only used in AP/VLAN modes (for power
saving stations.)

Overall, it is not necessary to even have the master netdev
be a valid virtual interface, and it doesn't have to be on
the list of interfaces either.

This patch changes the master netdev to be special, it now
 - no longer is on the list of virtual interfaces, which
   lets me remove a lot of tests for that
 - no longer has sub_if_data attached, since that isn't used

Additionally, this patch changes some vlan/ap mode handling
that is related to these 'bss' pointers described above (but
in the VLAN case they actually make sense because there they
point to the AP they belong to); it also adds some debugging
code to IEEE80211_DEV_TO_SUB_IF to validate it is not called
on the master netdev any more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When CONFIG_HOTPLUG=n the following error occures on vmlinux linkage:

`.exit.text' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.exit.text' of drivers/built-in.o

'rtl8187_disconnect' function marked as __devexit isn't compiled with no
hotplug support. Added __devexit_p macros to fix the problem.
Signed-off-by: Ihar Hrachyshka <ihar.hrachyshka@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As soon as an interface is enabled, and that interface is in adhoc or master mode,
the device will start raising beacondone interrupts. But before the first interrupt is
raised, mac80211 will probably not have send any beacons to the device yet, which
results in a NULL pointer error when the skb is being freed.

Note that the "raise beacondone interrupts without a beacon" is also a bug,
and will be addressed later. The more important bug however is preventing
the NULL pointer failt itself, since there might be other conditions that could trigger
it as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch implements the power management routines wireless extensions
for mac80211.
For now we only support switching PS mode between on and off.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

Multiple TX queue support is a core networking feature.
Signed-off-by: David S. Miller <davem@davemloft.net>

Accesses are mostly structured such that when there are multiple TX
queues the code transformations will be a little bit simpler.
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows us to use this calling convention all the way down into
qdisc_restart().
Signed-off-by: David S. Miller <davem@davemloft.net>

Only plain netif_schedule() remains taking a net_device, mostly as a
compatability item while we transition the rest of these interfaces.

Everything else calls netif_schedule_queue() or __netif_schedule(),
both of which take a netdev_queue pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Accomplish this by using local variables.
Signed-off-by: David S. Miller <davem@davemloft.net>

This indicates if the NOOP scheduler is what is active for TX on a
given device.
Signed-off-by: David S. Miller <davem@davemloft.net>

First, we add a qdisc_tx_changing() helper which returns true if the
qdisc attachment is in transition.

Second, we remove an assertion warning which is of limited value and
is hard to express precisely in a multiqueue environment.
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a helper function, currently used by IRDA.

This is being added so that we can contain and isolate as many
explicit ->tx_queue references in the tree as possible.
Signed-off-by: David S. Miller <davem@davemloft.net>

Isolate callers that want to simply reset all the TX qdiscs from the
details of TX queues.

Use this in the ISDN code.
Signed-off-by: David S. Miller <davem@davemloft.net>

We schedule queues, not the device, for output queue processing in BH.
Signed-off-by: David S. Miller <davem@davemloft.net>

It just wants the root qdisc given an arbitrary qdisc,
and that is simply qdisc->dev_queue->qdisc
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>

It is always equal to qdisc->dev_queue->lock
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that our qdisc management is bi-directional, per-queue, and fully
orthogonal, there is no reason to have a special ingress qdisc pointer
in struct net_device.
Signed-off-by: David S. Miller <davem@davemloft.net>

Now qdisc, qdisc_sleeping, and qdisc_list also live there.
Signed-off-by: David S. Miller <davem@davemloft.net>

Every qdisc is assosciated with a queue, and in the case of ingress
qdiscs that will now be netdev->rx_queue so using that queue's lock is
the thing to do.
Signed-off-by: David S. Miller <davem@davemloft.net>

The lock is now an attribute of the device queue.

One thing to notice is that "suspicious" places
emerge which will need specific training about
multiple queue handling.  They are so marked with
explicit "netdev->rx_queue" and "netdev->tx_queue"
references.
Signed-off-by: David S. Miller <davem@davemloft.net>

It can be obtained via the netdev_queue.  So create a helper routine,
qdisc_dev(), to make the transformations nicer looking.

Now, qdisc_alloc() now no longer needs a net_device pointer argument.
Signed-off-by: David S. Miller <davem@davemloft.net>

A netdev_queue is an entity managed by a qdisc.

Currently there is one RX and one TX queue, and a netdev_queue merely
contains a backpointer to the net_device.

The Qdisc struct is augmented with a netdev_queue pointer as well.

Eventually the 'dev' Qdisc member will go away and we will have the
resulting hierarchy:

	net_device --> netdev_queue --> Qdisc

Also, qdisc_alloc() and qdisc_create_dflt() now take a netdev_queue
pointer argument.
Signed-off-by: David S. Miller <davem@davemloft.net>

We haven't had netdev->tbusy in many years :)
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:

	drivers/net/wireless/iwlwifi/iwl-3945.c
	net/mac80211/mlme.c

- vlan_dev_reorder_header() is only called on the receive path after
  calling skb_share_check(). This means we can use skb_cow() since
  all we need is a writable header.

- vlan_dev_hard_header() includes a work-around for some apparently
  broken out of tree MPLS code. The hard_header functions can expect
  to always have a headroom of at least there own hard_header_len
  available, so the reallocation check is unnecessary.

- __vlan_put_tag() can use skb_cow_head() to avoid the skb_unshare()
  copy when the header is writable.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consider the following scenario:

ipv6_del_addr(ifp)
  ipv6_ifa_notify(RTM_DELADDR, ifp)
    ip6_del_rt(ifp->rt)

after returning from the ipv6_ifa_notify and enabling BH-s
back, but *before* calling the addrconf_del_timer the 
ifp->timer fires and:

addrconf_dad_timer(ifp)
  addrconf_dad_completed(ifp)
    ipv6_ifa_notify(RTM_NEWADDR, ifp)
      ip6_ins_rt(ifp->rt)

then return back to the ipv6_del_addr and:

in6_ifa_put(ifp)
  inet6_ifa_finish_destroy(ifp)
    dst_release(&ifp->rt->u.dst)

After this we have an ifp->rt inserted into fib6 lists, but 
queued for gc, which in turn can result in oopses in the
fib6_run_gc. Maybe some other nasty things, but we caught 
only the oops in gc so far.

The solution is to disarm the ifp->timer before flushing the
rt from it.
Signed-off-by: Andrey Vagin <avagin@parallels.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although I only tested similar code (I don't use any of this wireless
code), the state maintainance between Netlink dump callback invocations
seems wrong here and should lead to an endless loop. There are also other
examples in the same file which might have the same problem. Perhaps someone
can actually test this (or refute my logic).

Take the simple example with only one element in the list (which should fit
into the message):

1. invocation:
  Start:
    idx = 0, start = 0
  Loop:
    condition (++idx < start) => (1 < 0) => false
    => no continue, fill one entry, exit loop, return skb->len > 0

2. invocation:
  Start:
    idx = 0, start = 1
  Loop:
    condition (++idx < start) => (1 < 1) => false
    => no continue, fill the same entry again, exit loop, return skb->len > 0

3. invocation:
  Same as 2. invocation, endless invocation of callback.

Also, iterations where the filling of an element fails should not be counted as
completed, so idx should not be incremented in this case.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some early versions of RTL8187B devices have a USB ID of 0x8187
rather than the 0x8189 of later models. In addition, it appears
that these early units also must be programmed with lower power.
Previous patches used the Product ID string to detect this situation,
but did not address the low power question. This patch uses the
hardware version and sets the power accordingly.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>