- 21 Oct, 2021 8 commits
-
-
Vladimir Oltean authored
The enetc driver does not implement .ndo_change_mtu, instead it configures the MAC register field PTC{Traffic Class}MSDUR[MAXSDU] statically to a large value during probe time. The driver used to configure only the max SDU for traffic class 0, and that was fine while the driver could only use traffic class 0. But with the introduction of mqprio, sending a large frame into any other TC than 0 is broken. This patch fixes that by replicating per traffic class the static configuration done in enetc_configure_port_mac(). Fixes: cbe9e835 ("enetc: Enable TC offloading with mqprio") Reported-by:Richie Pearn <richard.pearn@nxp.com> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
<Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20211020173340.1089992-1-vladimir.oltean@nxp.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Vladimir Oltean authored
There are two counters named "MAC tx frames", one of them is actually incorrect. The correct name for that counter should be "MAC tx error frames", which is symmetric to the existing "MAC rx error frames". Fixes: 16eb4c85 ("enetc: Add ethtool statistics") Signed-off-by:
-
Yang Yingliang authored
'vclock_index' is accessed from sysfs, it shouled be freed in release function, so move it from ptp_clock_unregister() to ptp_clock_release(). Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Erik Ekman authored
Use pci_info instead to avoid unnamed/uninitialized noise: [197088.688729] sfc 0000:01:00.0: Solarflare NIC detected [197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F [197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed [197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support Inspired by fa44821a ("sfc: don't use netif_info et al before net_device is registered") from Heiner Kallweit. Signed-off-by:
Erik Ekman <erik@kryo.se> Acked-by:
Martin Habets <habetsm.xilinx@gmail.com> Signed-off-by:
-
Erik Ekman authored
The 1/10GbaseT modes were set up for cards with SFP+ cages in 3497ed8c ("sfc: report supported link speeds on SFP connections"). 10GbaseT was likely used since no 10G fibre mode existed. The missing fibre modes for 1/10G were added to ethtool.h in 5711a982 ("net: ethtool: add support for 1000BaseX and missing 10G link modes") shortly thereafter. The user guide available at https://support-nic.xilinx.com/wp/drivers lists support for the following cable and transceiver types in section 2.9: - QSFP28 100G Direct Attach Cables - QSFP28 100G SR Optical Transceivers (with SR4 modules listed) - SFP28 25G Direct Attach Cables - SFP28 25G SR Optical Transceivers - QSFP+ 40G Direct Attach Cables - QSFP+ 40G Active Optical Cables - QSFP+ 40G SR4 Optical Transceivers - QSFP+ to SFP+ Breakout Direct Attach Cables - QSFP+ to SFP+ Breakout Active Optical Cables - SFP+ 10G Direct Attach Cables - SFP+ 10G SR Optical Transceivers - SFP+ 10G LR Optical Transceivers - SFP 1000BASE‐T Transceivers - 1G Optical Transceivers (From user guide issue 28. Issue 16 which also includes older cards like SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.) Regarding SFP+ 10GBASE‐T transceivers the latest guide says: "Solarflare adapters do not support 10GBASE‐T transceiver modules." Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR). Before: $ ethtool ext Settings for ext: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full 10000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Advertised FEC modes: Not reported Link partner advertised link modes: Not reported Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: off Port: FIBRE PHYAD: 255 Transceiver: internal Current message level: 0x000020f7 (8439) drv probe link ifdown ifup rx_err tx_err hw Link detected: yes After: $ ethtool ext Settings for ext: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full 1000baseX/Full 10000baseCR/Full 10000baseSR/Full 10000baseLR/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Advertised FEC modes: Not reported Link partner advertised link modes: Not reported Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: off Port: FIBRE PHYAD: 255 Transceiver: internal Supports Wake-on: g Wake-on: d Current message level: 0x000020f7 (8439) drv probe link ifdown ifup rx_err tx_err hw Link detected: yes Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter/IPVS fixes for net The following patchset contains Netfilter fixes for net: 1) Crash due to missing initialization of timer data in xt_IDLETIMER, from Juhee Kang. 2) NF_CONNTRACK_SECMARK should be bool in Kconfig, from Vegard Nossum. 3) Skip netdev events on netns removal, from Florian Westphal. 4) Add testcase to show port shadowing via UDP, also from Florian. 5) Remove pr_debug() code in ip6t_rt, this fixes a crash due to unsafe access to non-linear skbuff, from Xin Long. 6) Make net/ipv4/vs/debug_level read-only from non-init netns, from Antoine Tenart. 7) Remove bogus invocation to bash in selftests/netfilter/nft_flowtable.sh also from Florian. ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-fixes-2021-10-20 ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueDavid S. Miller authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-10-20 This series contains updates to e1000e, igc, and ice drivers. Sasha fixes an issue with dropped packets on Tiger Lake platforms for e1000e and corrects a device ID for igc. Tony adds missing E810 device IDs for ice. ==================== Signed-off-by:
-
- 20 Oct, 2021 22 commits
-
-
Emeel Hakim authored
Current Work Queue Entry (WQE) checksum (csum) flags in the ethernet segment (eseg) in case of IPsec crypto offload datapath are not aligned with PRM/HW expectations. Currently the driver always sets the l3_inner_csum flag in case of IPsec because of the wrong usage of skb->encapsulation as indicator for inner IPsec header since skb->encapsulation is always ON for IPsec packets since IPsec itself is an encapsulation protocol. The above forced a failing attempts of calculating csum of non-existing segments (like in the IP|ESP|TCP packet case which does not have an l3_inner) which led to lots of packet drops hence the low throughput. Fix by using xo->inner_ipproto as indicator for inner IPsec header instead of skb->encapsulation in addition to setting the csum flags as following: * Tunnel Mode: * Pkt: MAC IP ESP IP L4 * CSUM: l3_cs | l3_inner_cs | l4_inner_cs * * Transport Mode: * Pkt: MAC IP ESP L4 * CSUM: l3_cs [ | l4_cs (checksum partial case)] * * Tunnel(VXLAN TCP/UDP) over Transport Mode * Pkt: MAC IP ESP UDP VXLAN IP L4 * CSUM: l3_cs | l3_inner_cs | l4_inner_cs Fixes: f1267798 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload") Signed-off-by:
Emeel Hakim <ehakim@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Emeel Hakim authored
IPsec crypto offload current Software Parser (SWP) fields settings in the ethernet segment (eseg) are not aligned with PRM/HW expectations. Among others in case of IP|ESP|TCP packet, current driver sets the offsets for inner_l3 and inner_l4 although there is no inner l3/l4 headers relative to ESP header in such packets. SWP provides the offsets for HW ,so it can be used to find csum fields to offload the checksum, however these are not necessarily used by HW and are used as fallback in case HW fails to parse the packet, e.g when performing IPSec Transport Aware (IP | ESP | TCP) there is no need to add SW parse on inner packet. So in some cases packets csum was calculated correctly , whereas in other cases it failed. The later faced csum errors (caused by wrong packet length calculations) which led to lots of packet drops hence the low throughput. Fix by setting the SWP fields as expected in a IP|ESP|TCP packet. the following describe the expected SWP offsets: * Tunnel Mode: * SWP: OutL3 InL3 InL4 * Pkt: MAC IP ESP IP L4 * * Transport Mode: * SWP: OutL3 OutL4 * Pkt: MAC IP ESP L4 * * Tunnel(VXLAN TCP/UDP) over Transport Mode * SWP: OutL3 InL3 InL4 * Pkt: MAC IP ESP UDP VXLAN IP L4 Fixes: f1267798 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload") Signed-off-by:
Raed Salem <raeds@nvidia.com> Signed-off-by:
-
Moshe Shemesh authored
During suspend flow the driver calls mlx5e_destroy_vlan_table() which does not only delete the vlans steering flow rules, but also frees the data on currently active vlans, thus it is not restored during resume flow. This fix keeps the vlan data on suspend flow and frees it only on driver remove flow. Fixes: 6783f0a2 ("net/mlx5e: Dynamic alloc vlan table for netdev when needed") Signed-off-by:
Moshe Shemesh <moshe@nvidia.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
-
Dmytro Linkin authored
Dan Carpenter report: The patch f47e04eb: "net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups" from May 31, 2021, leads to the following Smatch static checker warning: drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c:483 esw_qos_create_rate_group() warn: passing zero to 'ERR_PTR' If min rate normalization failed then error code may be overwritten to 0 if scheduling element destruction succeed. Ignore this value and always return initial one. Fixes: f47e04eb ("net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Dmytro Linkin <dlinkin@nvidia.com> Signed-off-by:
-
Maor Dickman authored
Both multipath and bonding events are changing the HW LAG state independently. Handling one of the features events while the other is already enabled can cause unwanted behavior, for example handling bonding event while multipath enabled will disable the lag and cause multipath to stop working. Fix it by ignoring bonding event while in multipath and ignoring FIB events while in bonding mode. Fixes: 544fe7c2 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events") Signed-off-by:
Maor Dickman <maord@nvidia.com> Reviewed-by:
Roi Dayan <roid@nvidia.com> Reviewed-by:
Mark Bloch <mbloch@nvidia.com> Signed-off-by:
-
Tony Nguyen authored
As part of support for E810 XXV devices, some device ids were inadvertently left out. Add those missing ids. Fixes: 195fb977 ("ice: add additional E810 device id") Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Acked-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by:
Paul Menzel <pmenzel@molgen.mpg.de>
-
Sasha Neftin authored
The device ID for I226_K was incorrectly assigned, update the device ID to the correct one. Fixes: bfa5e98c ("igc: Add new device ID") Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by:
-
Sasha Neftin authored
Update the HW MAC initialization flow. Do not gate DMA clock from the modPHY block. Keeping this clock will prevent dropped packets sent in burst mode on the Kumeran interface. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213651 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213377 Fixes: fb776f5d ("e1000e: Add support for Tiger Lake") Signed-off-by:
Mark Pearson <markpearson@lenovo.com> Tested-by:
-
Sasha Neftin authored
We have the same LAN controller on different PCHs. Separate TGP board type from SPT which will allow for specific fixes to be applied for TGP platforms. Suggested-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
Yang Yingliang authored
I got memory leak as follows when doing fault injection test: unreferenced object 0xffff88800906c618 (size 8): comm "i2c-idt82p33931", pid 4421, jiffies 4294948083 (age 13.188s) hex dump (first 8 bytes): 70 74 70 30 00 00 00 00 ptp0.... backtrace: [<00000000312ed458>] __kmalloc_track_caller+0x19f/0x3a0 [<0000000079f6e2ff>] kvasprintf+0xb5/0x150 [<0000000026aae54f>] kvasprintf_const+0x60/0x190 [<00000000f323a5f7>] kobject_set_name_vargs+0x56/0x150 [<000000004e35abdd>] dev_set_name+0xc0/0x100 [<00000000f20cfe25>] ptp_clock_register+0x9f4/0xd30 [ptp] [<000000008bb9f0de>] idt82p33_probe.cold+0x8b6/0x1561 [ptp_idt82p33] When posix_clock_register() returns an error, the name allocated in dev_set_name() will be leaked, the put_device() should be used to give up the device reference, then the name will be freed in kobject_cleanup() and other memory will be freed in ptp_clock_release(). Reported-by:Hulk Robot <hulkci@huawei.com> Fixes: a33121e5 ("ptp: fix the race between the release of ptp_clock and cdev") Signed-off-by:
-
Kurt Kanzenbach authored
When utilizing End to End delay mechanism, the following error messages show up: |root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m |ptp4l[950.573]: selected /dev/ptp3 as PTP clock |ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE |ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE |ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1 |ptp4l[956.879]: selected best master clock 001395.fffe.4897b4 |ptp4l[956.879]: port 1: assuming the grand master role |ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER |ptp4l[962.017]: port 1: received DELAY_REQ without timestamp |ptp4l[962.273]: port 1: received DELAY_REQ without timestamp |ptp4l[963.090]: port 1: received DELAY_REQ without timestamp Commit f2fb6b62 ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a") already addresses this problem for the dwmac v5.10. However, same holds true for all dwmacs above version v4.10. Correct the check accordingly. Afterwards everything works as expected. Tested on Intel Atom(R) x6414RE Processor. Fixes: 14f34733 ("net: stmmac: Correctly take timestamp for PTPv2") Fixes: f2fb6b62 ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a") Suggested-by:
Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by:
Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by:
-
Uwe Kleine-König authored
If something goes wrong in the remove callback, returning an error code just results in an error message. The device still disappears. So don't skip disabling the regulator in st95hf_remove() if resetting the controller via spi fails. Also don't return an error code which just results in two error messages. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
David S. Miller authored
Guangbin Huang says: ==================== net: hns3: add some fixes for -net This series adds some fixes for the HNS3 ethernet driver. ==================== Signed-off-by: -
Peng Li authored
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko. hns3.ko includes network stack and pci_driver, hclge.ko includes HW device action, algo_ops and timer task, hnae3.ko includes some register function. When SRIOV is enable and hclge.ko is removed, HW device is unloaded but VF still exists, PF will not reply VF mbx messages, and cause errors. This patch fix it by disable SRIOV before remove hclge.ko. Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
Yufeng Mo authored
The task of VF reset is performed through the workqueue. It checks the value of hdev->reset_pending to determine whether to exit the loop. However, the value of hdev->reset_pending may also be assigned by the interrupt function hclgevf_misc_irq_handle(), which may cause the loop fail to exit and keep occupying the workqueue. This loop is not necessary, so remove it and the workqueue will be rescheduled if the reset needs to be retried or a new reset occurs. Fixes: 1cc9bc6e ("net: hns3: split hclgevf_reset() into preparing and rebuilding part") Signed-off-by:
Yufeng Mo <moyufeng@huawei.com> Signed-off-by:
-
Yunsheng Lin authored
Currently when there is a rx page allocation failure, it is possible that polling may be stopped if there is no more packet to be reveiced, which may cause queue stall problem under memory pressure. This patch makes sure polling is scheduled again when there is any rx page allocation failure, and polling will try to allocate receive buffers until it succeeds. Now the allocation retry is added, it is unnecessary to do the rx page allocation at the end of rx cleaning, so remove it. And reset the unused_count to zero after calling hns3_nic_alloc_rx_buffers() to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under memory pressure. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
-
Yunsheng Lin authored
rx unused desc is the desc that need attatching new buffer before refilling to hw to receive new packet, the number of desc need attatching new buffer is calculated using next_to_use and next_to_clean. when next_to_use == next_to_clean, currently hns3 driver assumes that all the desc has the buffer attatched, but 'next_to_use == next_to_clean' also means all the desc need attatching new buffer if hw has comsumed all the desc and the driver has not attatched any buffer to the desc yet. This patch adds 'refill' in desc_cb to indicate whether a new buffer has been refilled to a desc. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by:
-
Yunsheng Lin authored
Currently the max tx size supported by the hw is calculated by using the max BD num supported by the hw. According to the hw user manual, the max tx size is fixed value for both non-TSO and TSO skb. This patch updates the max tx size according to the manual. Fixes: 8ae10cfb("net: hns3: support tx-scatter-gather-fraglist feature") Signed-off-by:
-
Guangbin Huang authored
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP mode. In this case, this tc may occupy all the tx bandwidth if it has huge traffic, so it violates the purpose of the user setting. To fix this problem, limit the ets dwrr bandwidth must greater than 0. Fixes: cacde272 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by:
-
Guangbin Huang authored
Currently, DWRR of tc will be initialized to a fixed value when this tc is enabled, but it is not been reset to 0 when this tc is disabled. It cause a problem that the DWRR of unused tc is not 0 after using tc tool to add and delete multi-tc parameters. For examples, after enabling 4 TCs and restoring to 1 TC by follow tc commands: $ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \ 8@0 8@8 8@16 8@24 hw 1 mode channel $ tc qdisc del dev eth0 root Now there is just one TC is enabled for eth0, but the tc info querying by debugfs is shown as follow: $ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info enabled tc number: 1 weight_offset: 14 TC MODE WEIGHT 0 dwrr 100 1 dwrr 100 2 dwrr 100 3 dwrr 100 4 dwrr 0 5 dwrr 0 6 dwrr 0 7 dwrr 0 This patch fixes it by resetting DWRR of tc to 0 when tc is disabled. Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by:
-
Jiaran Zhang authored
Add configuration of interrupt type and fifo interrupt enable of TM QCN error event if enabled, otherwise this event will not be reported when there is error. Fixes: d914971d ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()") Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by:
-
Eugene Crosser authored
This reverts commit 09e856d5. When an interface is enslaved in a VRF, prerouting conntrack hook is called twice: once in the context of the original input interface, and once in the context of the VRF interface. If no special precausions are taken, this leads to creation of two conntrack entries instead of one, and breaks SNAT. Commit above was intended to avoid creation of extra conntrack entries when input interface is enslaved in a VRF. It did so by resetting conntrack related data associated with the skb when it enters VRF context. However it breaks netfilter operation. Imagine a use case when conntrack zone must be assigned based on the original input interface, rather than VRF interface (that would make original interfaces indistinguishable). One could create netfilter rules similar to these: chain rawprerouting { type filter hook prerouting priority raw; iif realiface1 ct zone set 1 return iif realiface2 ct zone set 2 return } This works before the mentioned commit, but not after: zone assignment is "forgotten", and any subsequent NAT or filtering that is dependent on the conntrack zone does not work. Here is a reproducer script that demonstrates the difference in behaviour. ========== #!/bin/sh # This script demonstrates unexpected change of nftables behaviour # caused by commit 09e856d5 ""vrf: Reset skb conntrack # connection on VRF rcv" # https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1 # # Before the commit, it was possible to assign conntrack zone to a # packet (or mark it for `notracking`) in the prerouting chanin, raw # priority, based on the `iif` (interface from which the packet # arrived). # After the change, # if the interface is enslaved in a VRF, such # assignment is lost. Instead, assignment based on the `iif` matching # the VRF master interface is honored. Thus it is impossible to # distinguish packets based on the original interface. # # This script demonstrates this change of behaviour: conntrack zone 1 # or 2 is assigned depending on the match with the original interface # or the vrf master interface. It can be observed that conntrack entry # appears in different zone in the kernel versions before and after # the commit. IPIN=172.30.30.1 IPOUT=172.30.30.2 PFXL=30 ip li sh vein >/dev/null 2>&1 && ip li del vein ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf nft list table testct >/dev/null 2>&1 && nft delete table testct ip li add vein type veth peer veout ip li add tvrf type vrf table 9876 ip li set veout master tvrf ip li set vein up ip li set veout up ip li set tvrf up /sbin/sysctl -w net.ipv4.conf.veout.accept_local=1 /sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0 ip addr add $IPIN/$PFXL dev vein ip addr add $IPOUT/$PFXL dev veout nft -f - <<__END__ table testct { chain rawpre { type filter hook prerouting priority raw; iif { veout, tvrf } meta nftrace set 1 iif veout ct zone set 1 return iif tvrf ct zone set 2 return notrack } chain rawout { type filter hook output priority raw; notrack } } __END__ uname -rv conntrack -F ping -W 1 -c 1 -I vein $IPOUT conntrack -L Signed-off-by:
Eugene Crosser <crosser@average.org> Acked-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
- 19 Oct, 2021 5 commits
-
-
Christophe JAILLET authored
If we return before the end of the 'for_each_child_of_node()' iterator, the reference taken on 'port' must be released. Add the missing 'of_node_put()' calls. Fixes: 83c0afae ("net: dsa: Add new binding implementation") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/15d5310d1d55ad51c1af80775865306d92432e03.1634587046.git.christophe.jaillet@wanadoo.frSigned-off-by:
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-5.15-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2021-10-19 this is a pull request of a single patch for net/master. The patch is by me and fixes the error handling in case of a FC timeout in the TX path of the ISOTOP CAN protocol. ==================== Signed-off-by:
-
Zheyu Ma authored
During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Signed-off-by:
Zheyu Ma <zheyuma97@gmail.com> Signed-off-by:
-
Zheyu Ma authored
During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Signed-off-by:
-
Marc Kleine-Budde authored
When the a large chunk of data send and the receiver does not send a Flow Control frame back in time, the sendmsg() does not return a error code, but the number of bytes sent corresponding to the size of the packet. If a timeout occurs the isotp_tx_timer_handler() is fired, sets sk->sk_err and calls the sk->sk_error_report() function. It was wrongly expected that the error would be propagated to user space in every case. For isotp_sendmsg() blocking on wait_event_interruptible() this is not the case. This patch fixes the problem by checking if sk->sk_err is set and returning the error to user space. Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol") Link: https://github.com/hartkopp/can-isotp/issues/42 Link: https://github.com/hartkopp/can-isotp/pull/43 Link: https://lore.kernel.org/all/20210507091839.1366379-1-mkl@pengutronix.de Cc: stable@vger.kernel.org Reported-by:
Sottas Guillaume (LMB) <Guillaume.Sottas@liebherr.com> Tested-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
- 18 Oct, 2021 5 commits
-
-
Nathan Chancellor authored
A new warning in clang points out two places in this driver where boolean expressions are being used with a bitwise OR instead of a logical one: drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical] reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: note: cast one or both operands to int to silence this warning drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical] reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: note: cast one or both operands to int to silence this warning 2 errors generated. The motivation for the warning is that logical operations short circuit while bitwise operations do not. In this case, it does not seem like short circuiting is harmful so implement the suggested fix of changing to a logical operation to fix the warning. Link: https://github.com/ClangBuiltLinux/linux/issues/1479Reported-by:Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Nathan Chancellor <nathan@kernel.org> Reviewed-by:
-
Tianjia Zhang authored
Kernel TLS test has added SM4 GCM/CCM algorithm support, but SM4 algorithm is not compiled by default, this patch add SM4 config dependency. Reported-by:
Hangbin Liu <liuhangbin@gmail.com> Reported-by:
kernel test robot <oliver.sang@intel.com> Signed-off-by:
Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by:
-
Jeremy Kerr authored
We currently have some implicit padding in struct sockaddr_mctp. This patch makes this padding explicit, and ensures we have consistent layout on platforms with <32bit alignmnent. Fixes: 60fc6398 ("mctp: Add sockaddr_mctp to uapi") Signed-off-by:
Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by:
-
Jeremy Kerr authored
Use the more precise __kernel_sa_family_t for smctp_family, to match struct sockaddr. Also, use an unsigned int for the network member; negative networks don't make much sense. We're already using unsigned for mctp_dev and mctp_skb_cb, but need to change mctp_sock to suit. Fixes: 60fc6398 ("mctp: Add sockaddr_mctp to uapi") Signed-off-by:
Eugene Syromiatnikov <esyr@redhat.com> Signed-off-by:
-
Zheyu Ma authored
During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Signed-off-by:
-
