Jakub Kicinski says:

====================
ethtool: support FEC configuration over netlink

This series adds support for the equivalents of ETHTOOL_GFECPARAM
and ETHTOOL_SFECPARAM over netlink.

As a reminder - this is an API which allows user to query current
FEC mode, as well as set FEC manually if autoneg is disabled.
It does not configure anything if autoneg is enabled (that said
few/no drivers currently reject .set_fecparam calls while autoneg
is disabled, hopefully FW will just ignore the settings).

The existing functionality is mostly preserved in the new API.
The ioctl interface uses a set of flags, and link modes to tell
user which modes are supported. Here is how the flags translate
to the new interface (skipping descriptions for actual FEC modes):

  ioctl flag      |   description         |  new API
================================================================
ETHTOOL_FEC_OFF   | disabled (supported)  | \
ETHTOOL_FEC_RS    |                       |  ` link mode bitset
ETHTOOL_FEC_BASER |                       |  / .._A_FEC_MODES
ETHTOOL_FEC_LLRS  |                       | /
ETHTOOL_FEC_AUTO  | pick based on cable   | bool .._A_FEC_AUTO
ETHTOOL_FEC_NONE  | not supported         | no bit, no AUTO reported

Since link modes are already depended on (although somewhat implicitly)
for expressing supported modes - the new interface uses them for
the manual configuration, as well as uses link mode bit number
to communicate the active mode.

Use of link modes allows us to define any number of FEC modes we want,
and reuse the strset we already have defined.

Separating AUTO as its own attribute is the biggest changed compared
to the ioctl. It means drivers can no longer report AUTO as the
active FEC mode because there is no link mode for AUTO.
active_fec == AUTO makes little sense in the first place IMHO,
active_fec should be the actual mode, so hopefully this is fine.

The other minor departure is that None is no longer explicitly
expressed in the API. But drivers are reasonable in handling of
this somewhat pointless bit, so I'm not expecting any issues there.

One extension which could be considered would be moving active FEC
to ETHTOOL_MSG_LINKMODE_*, but then why not move all of FEC into
link modes? I don't know where to draw the line.

netdevsim support and a simple self test are included.

Next step is adding stats similar to the ones added for pause.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

,

Test FEC settings, iterate over configs.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for ethtool FEC and some ethtool error injection.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add FEC API to netlink.

This is not a 1-to-1 conversion.

FEC settings already depend on link modes to tell user which
modes are supported. Take this further an use link modes for
manual configuration. Old struct ethtool_fecparam is still
used to talk to the drivers, so we need to translate back
and forth. We can revisit the internal API if number of FEC
encodings starts to grow.

Enforce only one active FEC bit (by using a bit position
rather than another mask).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Lin <dslin1010@gmail.com>
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When cleared, the 'force' parameter in nexthop bucket replacement
notifications indicates that a driver should try to perform an atomic
replacement. Meaning, only update the contents of the bucket if it is
inactive.

Since mlxsw only queries buckets' activity once every second, there is
no point in trying an atomic replacement if the idle timer interval is
smaller than 1 second.

Currently, mlxsw ignores the original value of 'force' and will always
try an atomic replacement if the idle timer is not smaller than 1
second.

Fix this by taking the original value of 'force' into account and never
promoting a non-atomic replacement to an atomic one.

Fixes: 617a77f0 ("mlxsw: spectrum_router: Add nexthop bucket replacement support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
MPTCP: Allow initial subflow to be disconnected

An MPTCP connection is aggregated from multiple TCP subflows, and can
involve multiple IP addresses on either peer. The addresses used in the
initial subflow connection are assigned address id 0 on each side of the
link. More addresses can be added and shared with the peer using address
IDs of 1 or larger. MPTCP in Linux shares non-zero address IDs across
all MPTCP connections in a net namespace, which allows userspace to
manage subflow connections across a number of sockets. However, this
makes the address with id 0 a special case, since the IP address
associated with id 0 is potentially different for each socket.

This patch set allows the initial subflow to be disconnected when
userspace specifies an address to remove using both id 0 and an IP
address, or when the peer sends an RM_ADDR for id 0.

Patches 1 and 3 implement the change for requests from the peer and
userspace, respectively.

Patch 2 consolidates some code for disconnecting subflows.

Patches 4-6 update the self tests to cover removal of subflows using
address id 0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added the testcases for removing the id 0 subflow and the id 0
address.

In do_transfer, use the removing addresses number '9' for deleting the id
0 address.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the id 0 address, different MPTCP connections could be using
different IP addresses for id 0.

This patch added an extra argument IP address for del_addr when
using id 0.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IDs are supposed to be between 0 and 255.

In pm_nl_ctl, for both the 'add' and 'get' instruction, the ID is casted
in a u_int8_t. So if we give 256, we will delete ID 0. Obviously, the
goal is not to delete this ID by giving 256.

We could modify pm_nl_ctl and stop if the ID is negative or higher than
255 but probably better not to increase the number of lines for such
things in this tool which is only used in selftests. Instead, we use it
within the limits.

This modification also means that we will no longer add a new ID for the
2nd entry. That's why we removed an expected entry from the dump and
introduced with
commit dc8eb10e ("selftests: mptcp: add testcases for setting the address ID").

So now we delete ID 9 like before and we add entries for IDs 10 to 255
that are deleted just after.

Note that this could be seen as a fix but it was not really an issue so
far: we were simply playing with ID 0/1 once again. With the following
commit ("selftests: mptcp: add addr argument for del_addr"), it will be
different because ID 0 is going to required an address. We don't want
errors when trying to delete ID 0 without the address argument.
Acked-and-tested-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added a new function mptcp_nl_remove_id_zero_address to
remove the id 0 address.

In this function, traverse all the existing msk sockets to find the
msk matched the input IP address. Then fill the removing list with
id 0, and pass it to mptcp_pm_remove_addr and mptcp_pm_remove_subflow.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are some duplicate code in mptcp_pm_nl_rm_addr_received and
mptcp_pm_nl_rm_subflow_received. This patch unifies them into a new
function named mptcp_pm_nl_rm_addr_or_subflow. In it, use the input
parameter rm_type to identify it's now removing an address or a subflow.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's only one subflow involving the non-zero id address, but there
may be multi subflows involving the id 0 address.

Here's an example:

 local_id=0, remote_id=0
 local_id=1, remote_id=0
 local_id=0, remote_id=1

If the removing address id is 0, all the subflows involving the id 0
address need to be removed.

In mptcp_pm_nl_rm_addr_received/mptcp_pm_nl_rm_subflow_received, the
"break" prevents the iteration to the next subflow, so this patch
dropped them.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sysctl_icmp_echo_enable_probe is an u8.

ipv4_net_table entry should use
 .maxlen       = sizeof(u8).
 .proc_handler = proc_dou8vec_minmax,

Fixes: f1b8fa9f ("net: add sysctl for enabling RFC 8335 PROBE messages")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: code cleanup for heartbeat, dma error counts, sizeof, stats

These patches are a few more bits of code cleanup found in
testing and review: count all our dma error instances, make
better use of sizeof, fix a race in our device heartbeat check,
and clean up code formatting in the ethtool stats collection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Abstract out the per-queue data collection work into separate
functions from the per-queue loops in the stats reporting,
similar to what Alex did for the data label strings in
commit acebe5b6 ("ionic: Update driver to use ethtool_sprintf")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rework the heartbeat checks to be sure that we're getting an
atomic operation.  Through testing we found occasions where a
separate thread could clash with this check and cause erroneous
heartbeat check results.
Signed-off-by: Allen Hubbe <allenbh@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the actual pointer that we care about as the subject of the
sizeof, rather than a struct name.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increment our dma-error counter in a couple of spots
that were missed before.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
dpaa2-switch: add STP support

This patch set adds support for STP to the dpaa2-switch.

First of all, it fixes a bug which was determined by the improper usage
of bridge BR_STATE_* values directly in the MC ABI.
The next patches deal with creating an ACL table per port and trapping
the STP frames to the control interface by adding an entry into each
table.
The last patch configures proper learning state depending on the STP
state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Depending on what STP state a port is in, the learning on that port
should be enabled or disabled.

When the STP state is DISABLED, BLOCKING or LISTENING no learning should
be happening irrespective of what the bridge previously requested. The
learning state is changed to be the one setup by the bridge when the STP
state is LEARNING or FORWARDING.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add an ACL entry in each port's ACL table to redirect any frame that
has the destination MAC address equal to the STP dmac to the control
interface.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Keep track of the current learning state per port so that we can
reference it in the next patches when setting up a STP state.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to trap frames to the CPU, the DPAA2 switch uses the ACL table.
At probe time, create an ACL table for each switch port so that in the
next patches we can use this to trap STP frames and redirect them to the
control interface.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The numerical values used for STP states are different between the
bridge and the MC ABI therefore, the direct usage of the
BR_STATE_* macros directly in the structures passed to the firmware is
incorrect.

Create a separate function that translates between the bridge STP states
and the enum that holds the STP state as seen by the Management Complex.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use act_simple to verify that action created with 'tc actions change'
command exists after command returns. The goal is to verify internal action
API reference counting to ensure that the case when netlink message has
NLM_F_REPLACE flag set but action with specified index doesn't exist is
handled correctly.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
udp: GRO L4 improvements

This series improves the UDP L4 - either 'forward' or 'frag_list' -
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic.

The first for patches are mostly bugfixes, addressing some GRO
edge-cases when both tunnels and L4 are present, enabled and in use.

The next 3 patches avoid unneeded segmentation when UDP GRO
traffic traverses in the receive path UDP tunnels.

Finally, some self-tests are included, covering the relevant
GRO scenarios.

Even if most patches are actually bugfixes, this series is
targeting net-next, as overall it makes available a new feature.

v2 -> v3:
 - no code changes, more verbose commit messages and comment in
   patch 1/8

v1 -> v2:
 - restrict post segmentation csum fixup to the only the relevant pkts
 - use individual 'accept_gso_type' fields instead of whole gso bitmask
   (Willem)
 - use only ipv6 addesses from test range in self-tests (Willem)
 - hopefully clarified most individual patches commit messages
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a bunch of virtual topologies and verify that
NETIF_F_GRO_FRAGLIST or NETIF_F_GRO_UDP_FWD-enabled
devices aggregate the ingress packets as expected.
Additionally check that the aggregate packets are
segmented correctly when landing on a socket

Also test SKB_GSO_FRAGLIST and SKB_GSO_UDP_L4 aggregation
on top of UDP tunnel (vxlan)

v1 -> v2:
 - hopefully clarify the commit message
 - moved the overlay network ipv6 range into the 'documentation'
   reserved range (Willem)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the previous commit, let even geneve
passthrou the L4 GRO packets
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the previous commit, let even geneve
passthrou the L4 GRO packets
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When passing up an UDP GSO packet with L4 aggregation, there is
no need to segment it at the vxlan level. We can propagate the
packet untouched and let it be segmented later, if needed.

Introduce an helper to allow let the UDP socket to accept any
L4 aggregation and use it in the vxlan driver.

v1 -> v2:
 - updated to use the newly introduced UDP socket 'accept*' fields
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the UDP protocol delivers GSO_FRAGLIST packets to
the sockets without the expected segmentation.

This change addresses the issue introducing and maintaining
a couple of new fields to explicitly accept SKB_GSO_UDP_L4
or GSO_FRAGLIST packets. Additionally updates  udp_unexpected_gso()
accordingly.

UDP sockets enabling UDP_GRO stil keep accept_udp_fraglist
zeroed.

v1 -> v2:
 - use 2 bits instead of a whole GSO bitmask (Willem)

Fixes: 9fd1ff5d ("udp: Support UDP fraglist GRO/GSO.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the previous patch, the stack can do L4 UDP aggregation
on top of a UDP tunnel.

In such scenario, udp{4,6}_gro_complete will be called twice. This function
will enter its is_flist branch immediately, even though that is only
correct on the second call, as GSO_FRAGLIST is only relevant for the
inner packet.

Instead, we need to try first UDP tunnel-based aggregation, if the GRO
packet requires that.

This patch changes udp{4,6}_gro_complete to skip the frag list processing
when while encap_mark == 1, identifying processing of the outer tunnel
header.
Additionally, clears the field in udp_gro_complete() so that we can enter
the frag list path on the next round, for the inner header.

v1 -> v2:
 - hopefully clarified the commit message
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If NETIF_F_GRO_FRAGLIST or NETIF_F_GRO_UDP_FWD are enabled, and there
are UDP tunnels available in the system, udp_gro_receive() could end-up
doing L4 aggregation (either SKB_GSO_UDP_L4 or SKB_GSO_FRAGLIST) at
the outer UDP tunnel level for packets effectively carrying and UDP
tunnel header.

That could cause inner protocol corruption. If e.g. the relevant
packets carry a vxlan header, different vxlan ids will be ignored/
aggregated to the same GSO packet. Inner headers will be ignored, too,
so that e.g. TCP over vxlan push packets will be held in the GRO
engine till the next flush, etc.

Just skip the SKB_GSO_UDP_L4 and SKB_GSO_FRAGLIST code path if the
current packet could land in a UDP tunnel, and let udp_gro_receive()
do GRO via udp_sk(sk)->gro_receive.

The check implemented in this patch is broader than what is strictly
needed, as the existing UDP tunnel could be e.g. configured on top of
a different device: we could end-up skipping GRO at-all for some packets.

Anyhow, that is a very thin corner case and covering it will add quite
a bit of complexity.

v1 -> v2:
 - hopefully clarify the commit message

Fixes: 9fd1ff5d ("udp: Support UDP fraglist GRO/GSO.")
Fixes: 36707061 ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When UDP packets generated locally by a socket with UDP_SEGMENT
traverse the following path:

UDP tunnel(xmit) -> veth (segmentation) -> veth (gro) ->
	UDP tunnel (rx) -> UDP socket (no UDP_GRO)

ip_summed will be set to CHECKSUM_PARTIAL at creation time and
such checksum mode will be preserved in the above path up to the
UDP tunnel receive code where we have:

 __iptunnel_pull_header() -> skb_pull_rcsum() ->
skb_postpull_rcsum() -> __skb_postpull_rcsum()

The latter will convert the skb to CHECKSUM_NONE.

The UDP GSO packet will be later segmented as part of the rx socket
receive operation, and will present a CHECKSUM_NONE after segmentation.

Additionally the segmented packets UDP CB still refers to the original
GSO packet len. Overall that causes unexpected/wrong csum validation
errors later in the UDP receive path.

We could possibly address the issue with some additional checks and
csum mangling in the UDP tunnel code. Since the issue affects only
this UDP receive slow path, let's set a suitable csum status there.

Note that SKB_GSO_UDP_L4 or SKB_GSO_FRAGLIST packets lacking an UDP
encapsulation present a valid checksum when landing to udp_queue_rcv_skb(),
as the UDP checksum has been validated by the GRO engine.

v2 -> v3:
 - even more verbose commit message and comments

v1 -> v2:
 - restrict the csum update to the packets strictly needing them
 - hopefully clarify the commit message and code comments
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following whitescan warning:

Calling "zlib_inflateEnd(&state->strm)" is only useful for its return
value, which is ignored.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: remove repeated words

This patch-set removes some repeated words in comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove repeated words "that" and "the".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove repeated word "to".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove repeated word "that".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>