- 05 Oct, 2018 38 commits
-
-
Lorenzo Bianconi authored
Move mt76x2_dev in mt76x02_util.h and rename it in mt76x02_dev in order to be shared between mt76x2 and mt76x0 driver Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Remove hw_atomic_mutex mutex in mt76x0_dev data structure since mt76x0_phy_set_channel is already protected by mt76_dev mutex while mt76x0_chip_onoff is used just at device probe or cleanup Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Remove no longer used mac_lock spinlock and data array in mt76x0_dev data structure Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Use shared mt76x02 utility routines for rssi tracking. Moreover remove no longer used con_mon_lock spinlock and following variable: - ap_bssid - bcn_freq_off - bcn_phy_mode - avg_rssi Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Move mt76x02_rx_get_sta and mt76x02_rx_get_sta_wcid utility routines in mt76x02-lib module since it will be used by mt76x0 driver in order to unify rxwi parsing Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Move mt76x02_phy_get_min_avg_rssi in mt76x02-lib module since it will be used by mt76x0 driver in order to unify rxwi parsing Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Remove leftover configuration for legacy devices in mt76x0_init_mac_registers routine. Moreover remove unnecessary msleep delay Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Use mt76x02u_tx_prepare_skb routine to fill txwi in mt76x2u and mt76x0u driver and remove duplicated code. Moreover add static qualifier to mt76x02_mac_tx_rate_val and mt76x02_mac_fill_txwi routines Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Move mt76x02_mac_write_txwi in mt76x02_mac.c since it is shared between mt76x0 and mt76x2 drivers. This is a preliminary patch to unify txwi configuration between mt76x0 and mt76x2 drivers Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Add get_tx_txpwr_adj function pointer to mt76_driver_ops data structure as a preliminary patch to unify txwi configuration between mt76x0 and mt76x2 drivers since tpc is currently supported just by mt76x2 driver Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Move mt76x02_tx_get_max_txpwr_adj routine in mt76x02-lib module since now both mt76x0 and mt76x2 drivers read rate tx power gain from rate_power data structure. Moreover remove get_max_txpwr_adj function pointer from mt76_driver_ops data structure Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Stop mac and calibration work stopping the hw even if the device has been removed Fixes: b11e1969 ("mt76x0: add ieee80211_ops ops pointer to mt76x0_alloc_device signature") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
mt76u_alloc_queues need to be called before mt76u_mcu_init_rx since it initializes rx_page_lock spinlock used in mt76u_buf_alloc routine. Fixes: b11e1969 ("mt76x0: add ieee80211_ops ops pointer to mt76x0_alloc_device signature") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Stanislaw Gruszka authored
This is correct fix for c12128ce ("mt76: use a per rx queue page fragment cache"). We use wrong length when we allocate segments for MCU transmissions, which require bigger segment size than e->buf_size. Commit 481bb043 ("mt76: usb: make rx page_frag_cache access atomic") partially solved the problem or actually mask it by changing mt76u_mcu_init_rx() and mt76u_alloc_queues() sequence, so e->buf_size become non zero any longer, but still not big enough to handle MCU data. Patch fixes memory corruption which can manifest itself as random, not easy to reproduce crashes, during mt76 driver load or unload. Fixes: c12128ce ("mt76: use a per rx queue page fragment cache") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Colin Ian King authored
The header guards that are #defined are different from those being checked. Fix this by #defining them to the correct name. Fixes clang warnings: drivers/net/wireless/mediatek/mt76/mt76x02_mcu.h:17:9: warning: '__MT76x02_MCU_H' is used as a header guard here, followed by #define of a different macro [-Wheader-guard] drivers/net/wireless/mediatek/mt76/mt76x02_usb.h:17:9: warning: '__MT76x02_USB_H' is used as a header guard here, followed by #define of a different macro [-Wheader-guard] Fixes: 905db747 ("mt76: usb: move mt76x02 mcu code in mt76x02-usb module") Fixes: edaa580b ("mt76: move shared mcu_calibrate routine in mt76x02-lib module") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Move mt76x2 and mt76x2u drivers to mt76x2 subfolder and leave just shared code in mt76 root folder Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Add mt76x0e_cleanup routine to tidy up the device during device removal Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Sergey Matyukevich authored
Current implementation of dump_station cfg80211 callback supports AP mode only. Add support for STA mode as well: by default in STA mode this callback is supposed to return AP on managed interface. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sergey Matyukevich authored
Command responses and events from the firmware are copied twice in control path: at first in shm core (qtnf_shm_handle_new_data) and then in pcie bus drivers (qtnf_pcie_control_rx_callback). There is no need to copy this data twice, it can be done only once in rx callbacks. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sergey Matyukevich authored
Firmware supports scan dwell time tuning for various types of scans. Enable support for this feature: - advertise capability to configure channel dwell time to host - pass scan dwell parameters to wireless card in scan request Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sergey Matyukevich authored
Notify firmware to flush cache before scanning when needed. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sergey Matyukevich authored
On disconnect wireless core attempts to remove all the supported keys. Following cfg80211_ops conventions, firmware returns -ENOENT code for the out-of-bound key indexes. This is a normal behavior, so no need to report errors for this case. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sergey Matyukevich authored
Driver retrieves information about supported extended capabilities from wireless card. However this information is not propagated further to Linux wireless core. Fix this by setting extended capabilities fields of wiphy structure. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sergey Matyukevich authored
SGI should be passed to wireless core as a part of rate structure. Otherwise wireless core performs incorrect rate calculation when SGI is enabled in hardware but not reported to host. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Igor Mitsyanko authored
Do not cancel scan in disconnect callback. If there is an active scan, it will be cancelled by firmware, then host driver will be properly notified by event. Cancelling scan in disconnect callback occasionally may lead to the following race issue. Host is able to queue one scan after scan abort in disconnect callback, and another scan after scan abort in event handler. As a result, firmware receives second scan before the first scan completes. Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sergey Matyukevich authored
Unify command error handling using qtnf_cmd_resp_result_decode function. Do not duplicate error messages in command handlers and cfg80211 callbacks: report 'cmd exec fail' only on control path internal failure. Remove redundant 'unlikely' macros. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Igor Mitsyanko authored
Several members of pwr-MAC structure are re-initialized several times together with per-VIF initialization. Fix that and simplify the code. Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Igor Mitsyanko authored
In case firmware reports that it can not do OBSS scanning for 40MHz 2.4GHz channels itself, tell userpsace to do that instead by setting NL80211_FEATURE_NEED_OBSS_SCAN flag. Signed-off-by: Igor mitsyanko <igor.mitsyanko.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Igor Mitsyanko authored
When cfg80211 disconnect callback is triggered and command is processed by firmware, disconnect event with local parameter set must be sent immediately. Indicating that it's a "local" event (not from AP) will help upper layers to process this event correctly. Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sergey Matyukevich authored
Remove STA connection states tracking from driver. Leave it wireless core on host and to firmware. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/broadcom/b43/main.c: In function 'b43_one_core_detach': drivers/net/wireless/broadcom/b43/main.c:5496:17: warning: variable 'wl' set but not used [-Wunused-but-set-variable] After commit 644aa4d6 ("b43: remove list of IEEE 802.11 devices") 'wl' is not used any more. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Gustavo A. R. Silva authored
Replace "Fallthough" with a proper "fall through" annotation. This fix is part of the ongoing efforts to enabling -Wimplicit-fallthrough Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Michael Buesch <m@bues.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Lance Roy authored
lockdep_assert_held() is better suited to checking locking requirements, since it won't get confused when someone else holds the lock. This is also a step towards possibly removing spin_is_locked(). Signed-off-by: Lance Roy <ldr709@gmail.com> Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: <linux-wireless@vger.kernel.org> Cc: <netdev@vger.kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Tony Lindgren authored
Now with wlcore using PM runtime, we can also add support for Linux generic wakeirq handling for it if configured in the dts file. The wakeirq can be configured as the second interrupt in the dts file with interrupts-extended property where it is the padconf irq of the OOB GPIO pin used for wlcore interrupt. Note that eventually we should also allow configuring wlcore to use the SDIO dat1 IRQ for wake-up, and in that case the the wakeirq should be configured to be the padconf interrupt of the dat1 pin and not the padconf interrupt of the OOB GPIO pin. Cc: Eyal Reizer <eyalr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Tony Lindgren authored
We do not currently clear wl->elp_compl on ELP timeout and we have bogus lingering pointer that wlcore_irq then will try to access after recovery is done: BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580 ... (spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124) (do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74) (_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58) (complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore]) (wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64) (irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290) (irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c) (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20) ... After that the system will hang. Let's fix this by adding a flag for recovery and moving the recovery work call to to the error handling section. And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear it too in wl1271_recovery_work() and just downgrade the error to a warning to prevent overly verbose output. Cc: Eyal Reizer <eyalr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Ping-Ke Shih authored
The following: bool efuse_re_pg_sec1flag; u8 efuse_re_pg_data[8]; are not referenced anywhere in the rtlwifi code. This patch is originally created by Rick Veens <rickveens92@gmail.com>, and Joe Perches <joe@perches.com> reminded to apply it to rtlwifi. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Chung-Hsien Hsu authored
The driver sends an action frame down and waits for a completion signal triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event to continue the process. However, the action frame could be transmitted either on the current channel or on an off channel. For the on-channel case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when the frame is transmitted, which make the driver always wait a full timeout duration. This patch has the completion signal be triggered by receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel case. This change fixes WFA p2p certification 5.1.19 failure. Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Chung-Hsien Hsu authored
Finding a common channel to send an action frame out is required for some action types. Since a loop with several scan retry is used to find the channel, a short wait time could be considered for each attempt. This patch reduces the wait time from 1500 to 450 msec for each action frame scan. This patch fixes the WFA p2p certification 5.1.20 failure caused by the long action frame send time. Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
- 04 Oct, 2018 2 commits
-
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 4.20 * unify code between mt76x0, mt76x2 * mt76x0 fixes * tx power configuration fix for 76x2 * more progress on mt76x0e support * support for getting firmware version via ethtool * fix for rx buffer allocation regression on usb * fix for handling powersave responses * fix for mt76x2 beacon transmission
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for 4.20. Major changes: ath10k * retrieve MAC address from system firmware if provided * support extended board data download for dual-band QCA9984 * extended per sta tx statistics support via debugfs * average ack rssi support for data frames * speed up QCA6174 and QCA9377 firmware download using diag Copy Engine * HTT High Latency mode support needed by SDIO and USB support * get STA power save state via debugfs ath9k * add reset functionality for airtime station debugfs file
-