Physical TPMs use Open Firmware Device Tree bindings that are similar
to the IBM Power virtual TPM to support event log. However, these
properties store the values in different endianness for Physical
and Virtual TPM.

This patch fixes the endianness issue by doing appropriate conversion
based on Physical or Virtual TPM.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The current TPM 2.0 device driver extends only the SHA1 PCR bank
but the TCG Specification[1] recommends extending all active PCR
banks, to prevent malicious users from setting unused PCR banks with
fake measurements and quoting them.

The existing in-kernel interface(tpm_pcr_extend()) expects only a
SHA1 digest.  To extend all active PCR banks with differing
digest sizes, the SHA1 digest is padded with trailing 0's as needed.

This patch reuses the defined digest sizes from the crypto subsystem,
adding a dependency on CRYPTO_HASH_INFO module.

[1] TPM 2.0 Specification referred here is "TCG PC Client Specific
Platform Firmware Profile for TPM 2.0"
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

This patch implements the TPM 2.0 capability TPM_CAP_PCRS to
retrieve the active PCR banks from the TPM. This is needed
to enable extending all active banks as recommended by TPM 2.0
TCG Specification.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The error code handling is broken as any error code that has the same
bits set as TPM_RC_HASH passes. Implemented tpm2_rc_value() helper to
parse the error value from FMT0 and FMT1 error codes so that these types
of mistakes are prevented in the future.

Fixes: 5ca4c20c ("keys, trusted: select hash algorithm for TPM2 chips")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>

probe_itpm() function is supposed to send command without an itpm flag set
and if this fails to repeat it, this time with the itpm flag set.

However, commit 41a5e1cf ("tpm/tpm_tis: Split tpm_tis driver into a
core and TCG TIS compliant phy") moved the itpm flag from an "itpm"
variable to a TPM_TIS_ITPM_POSSIBLE chip flag, so setting the
(now function-local) itpm variable no longer had any effect.

Finally, this function-local itpm variable was removed by
commit 56af3221 ("tpm/tpm_tis: remove unused itpm variable")

Tested only on non-iTPM TIS TPM.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

For a long time the cdev read/write interface had this strange
idea that userspace had to read the result within 60 seconds otherwise
it is discarded. Perhaps this made sense under some older locking regime,
but in the modern kernel it is not required and is just dangerous.

Since something may be relying on this, double the timeout and print a
warning. We can remove the code in a few years, but this should be
enough to prevent new users.
Suggested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

These are non-generic functions and do not belong to tpm.h.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>

Otherwise some mask and inmask tokens with MAY_APPEND flag may not work
as expected.
Signed-off-by: Lans Zhang <jia.zhang@windriver.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>

On failure to return a pathname from ima_d_path(), a pointer to
dname is returned, which is subsequently used in the IMA measurement
list, the IMA audit records, and other audit logging.  Saving the
pointer to dname for later use has the potential to race with rename.

Intead of returning a pointer to dname on failure, this patch returns
a pointer to a copy of the filename.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org

Make sure that we have not received less bytes than what is indicated
in the header of the TPM response. Also, check the number of bytes in
the response before accessing its data.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>

Since commit 1107d065 ("tpm_tis: Introduce intermediate layer for
TPM access") Atmel 3203 TPM on ThinkPad X61S (TPM firmware version 13.9)
no longer works.  The initialization proceeds fine until we get and
start using chip-reported timeouts - and the chip reports C and D
timeouts of zero.

It turns out that until commit 8e54caf4 ("tpm: Provide a generic
means to override the chip returned timeouts") we had actually let
default timeout values remain in this case, so let's bring back this
behavior to make chips like Atmel 3203 work again.

Use a common code that was introduced by that commit so a warning is
printed in this case and /sys/class/tpm/tpm*/timeouts correctly says the
timeouts aren't chip-original.

Fixes: 1107d065 ("tpm_tis: Introduce intermediate layer for TPM access")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

This is a regression when this code was reworked and made the error
print unconditional. The original code deliberately suppressed printing
of the first error message so it could quietly sense
TPM_ERR_INVALID_POSTINIT.

Fixes: a502feb67b47 ("tpm: Clean up reading of timeout and duration capabilities")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

crb_check_resource() in TPM CRB driver calls
acpi_dev_resource_memory() which only handles 32-bit resources.
Adding a call to acpi_dev_resource_address_space() in TPM CRB
driver which handles 64-bit resources.
Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Drop duplicate header module.h from tpm_tis_spi.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm/st33zp24/st33zp24.c does not use any miscdevice so this patch remove
this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Use corret kdoc format for function description and eliminate warning
of type:

tpm_ibmvtpm.c:66: warning: No description found for parameter 'count'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The tpm stack uses pdev name convention for the parent device.
Fix that also in tpm_chip_alloc().

Fixes: 3897cd9c ("tpm: Split out the devm stuff from tpmm_chip_alloc")'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Use correct kdoc format, describe correct parameters and return values.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Functions tpm_transmit and transmit_cmd are referenced
from other functions kdoc hence deserve documentation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The SECCOMP_RET_KILL mode is documented as immediately killing the
process as if a SIGSYS had been sent and not caught (similar to a
SIGKILL).  However, a SIGSYS is documented as triggering a coredump
which does not happen today.

This has the advantage of being able to more easily debug a process
that fails a seccomp filter.  Today, most apps need to recompile and
change their filter in order to get detailed info out, or manually run
things through strace, or enable detailed kernel auditing.  Now we get
coredumps that fit into existing system-wide crash reporting setups.

From a security pov, this shouldn't be a problem.  Unhandled signals
can already be sent externally which trigger a coredump independent of
the status of the seccomp filter.  The act of dumping core itself does
not cause change in execution of the program.

URL: https://crbug.com/676357Signed-off-by: Mike Frysinger <vapier@chromium.org>
Acked-by: Jorge Lucangeli Obes <jorgelo@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>

I am still tired of having to find indirect ways to determine
what security modules are active on a system. I have added
/sys/kernel/security/lsm, which contains a comma separated
list of the active security modules. No more groping around
in /proc/filesystems or other clever hacks.

Unchanged from previous versions except for being updated
to the latest security next branch.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: John Johansen <john.johansen@canonical.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>

The kernel build bot turned up a bad config combination when
CONFIG_SECURITY_APPARMOR is y and CONFIG_SECURITY_APPARMOR_HASH is n,
resulting in the build error
   security/built-in.o: In function `aa_unpack':
   (.text+0x841e2): undefined reference to `aa_g_hash_policy'
Signed-off-by: John Johansen <john.johansen@canonical.com>

AA_BUG() uses WARN and won't break the kernel like BUG_ON().
Signed-off-by: John Johansen <john.johansen@canonical.com>

Signed-off-by: John Johansen <john.johansen@canonical.com>

Signed-off-by: John Johansen <john.johansen@canonical.com>

Signed-off-by: John Johansen <john.johansen@canonical.com>

Signed-off-by: John Johansen <john.johansen@canonical.com>

If this sysctl is set to non-zero and a process with CAP_MAC_ADMIN in
the root namespace has created an AppArmor policy namespace,
unprivileged processes will be able to change to a profile in the
newly created AppArmor policy namespace and, if the profile allows
CAP_MAC_ADMIN and appropriate file permissions, will be able to load
policy in the respective policy namespace.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>

Allow a profile to carry extra data that can be queried via userspace.
This provides a means to store extra data in a profile that a trusted
helper can extract and use from live policy.
Signed-off-by: William Hua <william.hua@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>

apparmor should be checking the SECURITY_CAP_NOAUDIT constant. Also
in complain mode make it so apparmor can elect to log a message,
informing of the check.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Allow turning off the computation of the policy hashes via the
apparmor.hash_policy kernel parameter.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Moving the use of fqname to later allows learning profiles to be based
on the fqname request instead of just the hname. It also allows cleaning
up some of the name parsing and lookup by allowing the use of
the fqlookupn_profile() lib fn.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Signed-off-by: John Johansen <john.johansen@canonical.com>

Signed-off-by: John Johansen <john.johansen@canonical.com>

The aad macro can replace aad strings when it is not intended to. Switch
to a fn macro so it is only applied when intended.

Also at the same time cleanup audit_data initialization by putting
common boiler plate behind a macro, and dropping the gfp_t parameter
which will become useless.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Having ops be an integer that is an index into an op name table is
awkward and brittle. Every op change requires an edit for both the
op constant and a string in the table. Instead switch to using const
strings directly, eliminating the need for the table that needs to
be kept in sync.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Signed-off-by: John Johansen <john.johansen@canonical.com>

Trying to update the task cred while the task current cred is not the
real cred will result in an error at the cred layer. Avoid this by
failing early and delaying the update.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Having per policy ns interface files helps with containers restoring
policy.
Signed-off-by: John Johansen <john.johansen@canonical.com>