Handle NRST asynchronously for SAM9X60 to avoid problem with fast drop of
VDDCORE on shutdown operations in the first 100 us after CPU is shutdown.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

After refactoring struct at91_reset_data and
struct at91_reset_data at91sam9260_reset_data are not needed anymore.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Keep only one reset function. With this, notifier_call member of
struct at91_reset_data could be removed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Make at91sam9g45_restart() generic.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Introduce ramc_lpr to struct at91_reset. This will lead to the
unification of at91sam9260_restart() and at91sam9g45_restart().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Use r4 as temporary register. On ARM r0-r3 should be used to hold
function arguments.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Introduce args member in struct at91_reset_data. It stores the value
that needs to be written in mode register so that the reboot actions
to happen. With these changes samx7_restart() could be removed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Introduce struct at91_reset_data to be able to provide per SoC
data. At the moment this being only notifier callback.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Allocate at91_reset data on probe and set it as platform data.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add new argument to at91_reset_status() that is the pointer to reset
controller base address.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Convert reset in pointer to struct at91_reset.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add struct notifier_block to struct at91_reset.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add sclk to struct at91_reset.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add ramc_base[] to struct at91_reset.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Introduce struct at91_reset intended to keep all the at91 reset controller
data.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Some HP Pavilion x2 10 models use an AXP288 for charging and fuel-gauge.
We use a native power_supply / PMIC driver in this case, because on most
models with an AXP288 the ACPI AC / Battery code is either completely
missing or relies on custom / proprietary ACPI OpRegions which Linux
does not implement.

The native drivers mostly work fine, but there are 2 problems:

1. These model uses a Type-C connector for charging which the AXP288 does
not support. As long as a Type-A charger (which uses the USB data pins for
charger type detection) is used everything is fine. But if a Type-C
charger is used (such as the charger shipped with the device) then the
charger is not recognized.

So we end up slowly discharging the device even though a charger is
connected, because we are limiting the current from the charger to 500mA.
To make things worse this happens with the device's official charger.

Looking at the ACPI tables HP has "solved" the problem of the AXP288 not
being able to recognize Type-C chargers by simply always programming the
input-current-limit at 3000mA and relying on a Vhold setting of 4.7V
(normally 4.4V) to limit the current intake if the charger cannot handle
this.

2. If no charger is connected when the machine boots then it boots with the
vbus-path disabled. On other devices this is done when a 5V boost converter
is active to avoid the PMIC trying to charge from the 5V boost output.
This is done when an OTG host cable is inserted and the ID pin on the
micro-B receptacle is pulled low, the ID pin has an ACPI event handler
associated with it which re-enables the vbus-path when the ID pin is pulled
high when the OTG cable is removed. The Type-C connector has no ID pin,
there is no ID pin handler and there appears to be no 5V boost converter,
so we end up not charging because the vbus-path is disabled, until we
unplug the charger which automatically clears the vbus-path disable bit and
then on the second plug-in of the adapter we start charging.

The HP Pavilion x2 10 models with an AXP288 do have mostly working ACPI
AC / Battery code which does not rely on custom / proprietary ACPI
OpRegions. So one possible solution would be to blacklist the AXP288
native power_supply drivers and add the HP Pavilion x2 10 with AXP288
DMI ids to the list of devices which should use the ACPI AC / Battery
code even though they have an AXP288 PMIC. This would require changes to
4 files: drivers/acpi/ac.c, drivers/power/supply/axp288_charger.c,
drivers/acpi/battery.c and drivers/power/supply/axp288_fuel_gauge.c.

Beside needing adding the same DMI matches to 4 different files, this
approach also triggers problem 2. from above, but then when suspended,
during suspend the machine will not wakeup because the vbus path is
disabled by the AML code when not charging, so the Vbus low-to-high
IRQ is not triggered, the CPU never wakes up and the device does not
charge even though the user likely things it is charging, esp. since
the charge status LED is directly coupled to an adapter being plugged
in and does not reflect actual charging.

This could be worked by enabling vbus-path explicitly from say the
axp288_charger driver's suspend handler.

So neither situation is ideal, in both cased we need to explicitly enable
the vbus-path to work around different variants of problem 2 above, this
requires a quirk in the axp288_charger code.

If we go the route of using the ACPI AC / Battery drivers then we need
modifications to 3 other drivers; and we need to partially disable the
axp288_charger code, while at the same time keeping it around to enable
vbus-path on suspend.

OTOH we can copy the hardcoding of 3A input-current-limit (we never touch
Vhold, so that would stay at 4.7V) to the axp288_charger code, which needs
changes regardless, then we concentrate all special handling of this
interesting device model in the axp288_charger code. That is what this
commit does.

Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1791098Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The Intel Compute Stick `STK1A32SC` can have a system vendor of
"Intel(R) Client Systems".
Broaden the Intel Compute Stick DMI checks so that they match "Intel
Corporation" as well as "Intel(R) Client Systems".

This fixes an issue where the STK1A32SC compute sticks were still
exposing a battery with the existing blacklist entry.
Signed-off-by: Jeffery Miller <jmiller@neverware.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Trivial fix to spelling mistake in commit messages.
Signed-off-by: Ashish Chavan <ashish.gschavan@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Allow charger manager can be built as a module like other charger
drivers.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add the POWER_SUPPLY_PROP_CHARGE_NOW attribute to allow user to get
current battery capacity (uAh) to do measurement.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Don't print an error message if devm_power_supply_register() returns
-EPROBE_DEFER, since the driver will simply re-probe later.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Pull more Kbuild updates from Masahiro Yamada:

 - fix randconfig to generate a sane .config

 - rename hostprogs-y / always to hostprogs / always-y, which are more
   natual syntax.

 - optimize scripts/kallsyms

 - fix yes2modconfig and mod2yesconfig

 - make multiple directory targets ('make foo/ bar/') work

* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: make multiple directory targets work
  kconfig: Invalidate all symbols after changing to y or m.
  kallsyms: fix type of kallsyms_token_table[]
  scripts/kallsyms: change table to store (strcut sym_entry *)
  scripts/kallsyms: rename local variables in read_symbol()
  kbuild: rename hostprogs-y/always to hostprogs/always-y
  kbuild: fix the document to use extra-y for vmlinux.lds
  kconfig: fix broken dependency in randconfig-generated .config

Pull new zonefs file system from Damien Le Moal:
 "Zonefs is a very simple file system exposing each zone of a zoned
  block device as a file.

  Unlike a regular file system with native zoned block device support
  (e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
  sequential write constraint of zoned block devices to the user. As a
  result, zonefs is not a POSIX compliant file system. Its goal is to
  simplify the implementation of zoned block devices support in
  applications by replacing raw block device file accesses with a richer
  file based API, avoiding relying on direct block device file ioctls
  which may be more obscure to developers.

  One example of this approach is the implementation of LSM
  (log-structured merge) tree structures (such as used in RocksDB and
  LevelDB) on zoned block devices by allowing SSTables to be stored in a
  zone file similarly to a regular file system rather than as a range of
  sectors of a zoned device. The introduction of the higher level
  construct "one file is one zone" can help reducing the amount of
  changes needed in the application while at the same time allowing the
  use of zoned block devices with various programming languages other
  than C.

  Zonefs IO management implementation uses the new iomap generic code.
  Zonefs has been successfully tested using a functional test suite
  (available with zonefs userland format tool on github) and a prototype
  implementation of LevelDB on top of zonefs"

* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: Add documentation
  fs: New zonefs file system

In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.

Fixes: 4e6437f1 ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull cifs fixes from Steve French:
 "13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:

   - Important fix for multichannel and for modefromsid mounts.

   - Two reconnect fixes

   - Addition of SMB3 change notify support

   - Backup tools fix

   - A few additional minor debug improvements (tracepoints and
     additional logging found useful during testing this week)"

* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add defines for new information level, FileIdInformation
  smb3: print warning once if posix context returned on open
  smb3: add one more dynamic tracepoint missing from strict fsync path
  cifs: fix mode bits from dir listing when mounted with modefromsid
  cifs: fix channel signing
  cifs: add SMB3 change notification support
  cifs: make multichannel warning more visible
  cifs: fix soft mounts hanging in the reconnect code
  cifs: Add tracepoints for errors on flush or fsync
  cifs: log warning message (once) if out of disk space
  cifs: fail i/o on soft mounts if sessionsetup errors out
  smb3: fix problem with null cifs super block with previous patch
  SMB3: Backup intent flag missing from some more ops

Pull vboxfs from Al Viro:
 "This is the VirtualBox guest shared folder support by Hans de Goede,
  with fixups for fs_parse folded in to avoid bisection hazards from
  those API changes..."

* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Add VirtualBox guest shared folder (vboxsf) support

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for X86:

   - Ensure that the PIT is set up when the local APIC is disable or
     configured in legacy mode. This is caused by an ordering issue
     introduced in the recent changes which skip PIT initialization when
     the TSC and APIC frequencies are already known.

   - Handle malformed SRAT tables during early ACPI parsing which caused
     an infinite loop anda boot hang.

   - Fix a long standing race in the affinity setting code which affects
     PCI devices with non-maskable MSI interrupts. The problem is caused
     by the non-atomic writes of the MSI address (destination APIC id)
     and data (vector) fields which the device uses to construct the MSI
     message. The non-atomic writes are mandated by PCI.

     If both fields change and the device raises an interrupt after
     writing address and before writing data, then the MSI block
     constructs a inconsistent message which causes interrupts to be
     lost and subsequent malfunction of the device.

     The fix is to redirect the interrupt to the new vector on the
     current CPU first and then switch it over to the new target CPU.
     This allows to observe an eventually raised interrupt in the
     transitional stage (old CPU, new vector) to be observed in the APIC
     IRR and retriggered on the new target CPU and the new vector.

     The potential spurious interrupts caused by this are harmless and
     can in the worst case expose a buggy driver (all handlers have to
     be able to deal with spurious interrupts as they can and do happen
     for various reasons).

   - Add the missing suspend/resume mechanism for the HYPERV hypercall
     page which prevents resume hibernation on HYPERV guests. This
     change got lost before the merge window.

   - Mask the IOAPIC before disabling the local APIC to prevent
     potentially stale IOAPIC remote IRR bits which cause stale
     interrupt lines after resume"

* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Mask IOAPIC entries when disabling the local APIC
  x86/hyperv: Suspend/resume the hypercall page for hibernation
  x86/apic/msi: Plug non-maskable MSI affinity race
  x86/boot: Handle malformed SRAT tables during early ACPI parsing
  x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode

Pull SMP fixes from Thomas Gleixner:
 "Two fixes for the SMP related functionality:

   - Make the UP version of smp_call_function_single() match SMP
     semantics when called for a not available CPU. Instead of emitting
     a warning and assuming that the function call target is CPU0,
     return a proper error code like the SMP version does.

   - Remove a superfluous check in smp_call_function_many_cond()"

* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smp/up: Make smp_call_function_single() match SMP semantics
  smp: Remove superfluous cond_func check in smp_call_function_many_cond()

Pull perf fixes from Thomas Gleixner:
 "A set of fixes and improvements for the perf subsystem:

  Kernel fixes:

   - Install cgroup events to the correct CPU context to prevent a
     potential list double add

   - Prevent an integer underflow in the perf mlock accounting

   - Add a missing prototype for arch_perf_update_userpage()

  Tooling:

   - Add a missing unlock in the error path of maps__insert() in perf
     maps.

   - Fix the build with the latest libbfd

   - Fix the perf parser so it does not delete parse event terms, which
     caused a regression for using perf with the ARM CoreSight as the
     sink configuration was missing due to the deletion.

   - Fix the double free in the perf CPU map merging test case

   - Add the missing ustring support for the perf probe command"

* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf maps: Add missing unlock to maps__insert() error case
  perf probe: Add ustring support for perf probe command
  perf: Make perf able to build with latest libbfd
  perf test: Fix test case Merge cpu map
  perf parse: Copy string to perf_evsel_config_term
  perf parse: Refactor 'struct perf_evsel_config_term'
  kernel/events: Add a missing prototype for arch_perf_update_userpage()
  perf/cgroups: Install cgroup events to correct cpuctx
  perf/core: Fix mlock accounting in perf_mmap()

Pull timer fixes from Thomas Gleixner:
 "Two small fixes for the time(r) subsystem:

   - Handle a subtle race between the clocksource watchdog and a
     concurrent clocksource watchdog stop/start sequence correctly to
     prevent a timer double add bug.

   - Fix the file path for the core time namespace file"

* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: Prevent double add_timer_on() for watchdog_timer
  MAINTAINERS: Correct path to time namespace source file

Pull interrupt fixes from Thomas Gleixner:
 "A set of fixes for the interrupt subsystem:

   - Provision only ACPI enabled redistributors on GICv3

   - Use the proper command colums when building the INVALL command for
     the GICv3-ITS

   - Ensure the allocation of the L2 vPE table for GICv4.1

   - Correct the GICv4.1 VPROBASER programming so it uses the proper
     size

   - A set of small GICv4.1 tidy up patches

   - Configuration cleanup for C-SKY interrupt chip

   - Clarify the function documentation for irq_set_wake() to document
     that the wakeup functionality is orthogonal to the irq
     disable/enable mechanism"

* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
  irqchip/gic-v3-its: Remove superfluous WARN_ON
  irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
  irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
  irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
  irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
  genirq: Clarify that irq wake state is orthogonal to enable/disable
  irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
  irqchip: Some Kconfig cleanup for C-SKY
  irqchip/gic-v3: Only provision redistributors that are enabled in ACPI

Pull EFI fix from Thomas Gleixner:
 "A single fix for a EFI boot regression on X86 which was caused by the
  recent rework of the EFI memory map parsing. On systems with invalid
  memmap entries the cleanup function uses an value which cannot be
  relied on in this stage. Use the actual EFI memmap entry instead"

* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/x86: Fix boot regression on systems with invalid memmap entries

Pull misc SCSI fixes from James Bottomley:
 "Five small patches, all in drivers or doc, which missed the initial
  pull request.

  The qla2xxx and megaraid_sas are actual fixes and the rest are
  spelling and doc changes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: fix spelling mistake "initilized" -> "initialized"
  scsi: pm80xx: fix spelling mistake "to" -> "too"
  scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
  scsi: megaraid_sas: fixup MSIx interrupt setup during resume
  scsi: qla2xxx: Fix unbound NVME response length

Pull networking fixes from David Miller:

 1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.

 2) Fix thermal zone registration in iwlwifi, from Andrei
    Otcheretianski.

 3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.

 4) Use after free in mptcp, from Florian Westphal.

 5) Use after free in wireguard's root_remove_peer_lists, from Eric
    Dumazet.

 6) Properly access packets heads in bonding alb code, from Eric
    Dumazet.

 7) Fix data race in skb_queue_len(), from Qian Cai.

 8) Fix regression in r8169 on some chips, from Heiner Kallweit.

 9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.

10) Certain kinds of set link netlink operations can cause a NULL deref
    in the ipv6 addrconf code. Fix from Eric Dumazet.

11) Don't cancel uninitialized work queue in drop monitor, from Ido
    Schimmel.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  net: thunderx: use proper interface type for RGMII
  mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
  bpf: Improve bucket_log calculation logic
  selftests/bpf: Test freeing sockmap/sockhash with a socket in it
  bpf, sockhash: Synchronize_rcu before free'ing map
  bpf, sockmap: Don't sleep while holding RCU lock on tear-down
  bpftool: Don't crash on missing xlated program instructions
  bpf, sockmap: Check update requirements after locking
  drop_monitor: Do not cancel uninitialized work item
  mlxsw: spectrum_dpipe: Add missing error path
  mlxsw: core: Add validation of hardware device types for MGPIR register
  mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
  selftests: mlxsw: Add test cases for local table route replacement
  mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
  net: dsa: microchip: enable module autoprobe
  ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
  dpaa_eth: support all modes with rate adapting PHYs
  net: stmmac: update pci platform data to use phy_interface
  net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
  net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
  ...

VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.

This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull powerpc fixes from Michael Ellerman:

 - Fix an existing bug in our user access handling, exposed by one of
   the bug fixes we merged this cycle.

 - A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
   recently added CONFIG_VMAP_STACK.

Thanks to: Christophe Leroy, Guenter Roeck.

* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
  powerpc/futex: Fix incorrect user access blocking

This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd ("Merge
tag 'ioremap-5.6' of git://../ioremap").

Apparently this didn't get any build testing anywhere.  Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.

I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC late updates from Olof Johansson:
 "This is some material that we picked up into our tree late, or that
  had more complex dependencies on more than one topic branch that makes
  sense to keep separately.

   - TI support for secure accelerators and hwrng on OMAP4/5

   - TI camera changes for dra7 and am437x and SGX improvement due to
     better reset control support on am335x, am437x and dra7

   - Davinci moves to proper clocksource on DM365, and regulator/audio
     improvements for DM365 and DM644x eval boards"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
  ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
  ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
  ARM: dts: Configure interconnect target module for am437x sgx
  ARM: dts: Configure sgx for dra7
  ARM: dts: Configure rstctrl reset for am335x SGX
  ARM: dts: dra7: Add ti-sysc node for VPE
  ARM: dts: dra7: add vpe clkctrl node
  ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
  ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
  ARM: dts: am43xx: add support for clkout1 clock
  arm: dts: dra76-evm: Add CAL and OV5640 nodes
  arm: dtsi: dra76x: Add CAL dtsi node
  arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
  ARM: dts: DRA72: Add CAL dtsi node
  ARM: dts: dra7-l4: Add ti-sysc node for CAM
  ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
  ARM: dts: dra7: add cam clkctrl node
  ARM: OMAP2+: Drop legacy platform data for omap4 des
  ARM: OMAP2+: Drop legacy platform data for omap4 sham
  ARM: OMAP2+: Drop legacy platform data for omap4 aes
  ...

Pull ARM SoC defconfig updates from Olof Johansson:
 "We keep this in a separate branch to avoid cross-branch conflicts, but
  most of the material here is fairly boring -- some new drivers turned
  on for hardware since they were merged, and some refreshed files due
  to time having moved a lot of entries around"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
  ARM: configs: at91: enable MMC_SDHCI_OF_AT91 and MICROCHIP_PIT64B
  arm64: defconfig: Enable Broadcom's GENET Ethernet controller
  ARM: multi_v7_defconfig: Enable devfreq thermal integration
  ARM: exynos_defconfig: Enable devfreq thermal integration
  ARM: multi_v7_defconfig: Enable NFS v4.1 and v4.2
  ARM: exynos_defconfig: Enable NFS v4.1 and v4.2
  arm64: defconfig: Enable Actions Semi specific drivers
  arm64: defconfig: Enable Broadcom's STB PCIe controller
  arm64: defconfig: Enable CONFIG_CLK_IMX8MP by default
  ARM: configs: at91: enable config flags for sam9x60 SoC
  ARM: configs: at91: use savedefconfig
  arm64: defconfig: Enable tegra XUDC support
  ARM: defconfig: gemini: Update defconfig
  arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM
  arm64: defconfig: enable CONFIG_QCOM_CPR
  arm64: defconfig: Enable HFPLL
  arm64: defconfig: Enable CRYPTO_DEV_FSL_CAAM
  ARM: imx_v6_v7_defconfig: Select the TFP410 driver
  ARM: imx_v6_v7_defconfig: Enable NFS_V4_1 and NFS_V4_2 support
  arm64: defconfig: Enable ATH10K_SNOC
  ...