This important fix checks the SAl *revision* rather than
the *version*.  I carefully documented which was which, then used the
wrong one.

This patch against 2.6.5-rc2 affects the SGI/SN platform only. It deprecates
a kernel daemon for our interconnect traffic statistics which has been
replaced by a userland tool.

Mainly cosmetic, but Bjorn noticed I got a little over zealous in
cleaning out the sx1000 specific init routines in sba_iommu.  This adds
back in the ID->name mapping so it doesn't show up as "Unknown".

Bjorn pointed out that the sn console driver will spew printks if
compiled in even if no hardware is present.  In addition to fixing
that, I took the opportunity to cleanup/correct a few other printks in
that driver.

sn_oemdata_* variables must only be used under the sn_oemdata_mutex.

into tiger.hpl.hp.com:/data1/bk/lia64/to-linus-2.5

into ppc970.osdl.org:/home/torvalds/v2.6/linux

While the sysctl variable is being worked out in the general kernel, here is
an interim patch which allows boot-time/dynamic control over the use of
PAL_HALT_LIGHT in the idle-loop.

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into kernel.bkbits.net:/home/davem/net-2.6

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

This rolls up Marc Zyngier's EISA correction (first two) and adds a missed
netdev_priv() conversion that was causing an oops on module removal.

Noticed by Jan Glauber, confirmed by Stephen Hemminger.

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into kroah.com:/home/greg/linux/BK/pci-2.6

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Call pci_claim_resources() so we can see what PCI resources are being used.

On ia64, the parent resources are not necessarily PCI resources and
so won't get found by pci_find_parent_resource.  Use the shiny new
insert_resource() function instead, which I think we would have used
here had it been available at the time.

If we start again, we can return an error even if we were successful.
Reset the result to 0 before beginning again.  Why don't we use a
tailcall here?

This prevents the "optimize && ?" message appearing when the kernel
configuration tool is run.  The message could be eliminated from the
tool, but I'd rather fix the needlessly over-complicated expression:

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

We no longer have a CPU_OFFLINE notifier: we freeze the machine and
kill the CPU atomically.  Remove it.

Various files keep per-cpu caches which need to be freed/moved when a
CPU goes down.  All under CONFIG_HOTPLUG_CPU ifdefs.

scsi.c: drain dead cpu's scsi_done_q onto this cpu.

buffer.c: brelse the bh_lrus queue for dead cpu.

timer.c: migrate timers from dead cpu, being careful of lock order vs
	__mod_timer.

radix_tree.c: free dead cpu's radix_tree_preloads

page_alloc.c: empty dead cpu's nr_pagecache_local into nr_pagecache, and
	free pages on cpu's local cache.

slab.c: stop reap_timer for dead cpu, adjust each cache's free limit, and
	free each slab cache's per-cpu block.

swap.c: drain dead cpu's lru_add_pvecs into ours, and empty its committed_space
	counter into global counter.

dev.c: drain device queues from dead cpu into this one.

flow.c: drain dead cpu's flow cache.

Keep track of kswapds: it's OK that they get moved off a node when the
last CPU goes down, but when a CPU comes back, we should try to move
the kswapd back onto its node.

Workqueues need to bring up/destroy the per-cpu thread on cpu up/down.

1) Add a global list of workqueues, and keep the name in the structure
   (to name the newly created thread).

2) Remove BUG_ON in run_workqueue, since thread is dragged off CPU when
   it goes down.

3) Lock out cpu up/down in flush_workqueue, create_workqueue and
   destroy_workqueue.

4) Add notifier to add/destroy workqueue threads, and take over work.

Change ksoftirqd not to assume it's on the CPU: when a cpu goes down,
it will be rudely dragged off.  Since do_softirq() uses
smp_processor_id(), it's easiest to disable preemption, check that the
cpu is still up, then call do_softirq().

If the cpu is actually offline, wait for the notifier, which kills us.

Take over tasklets from dead cpu in the notifier.

Clean up redundant double assignment in CPU_UP callback.

Add hook for RCU to handle jobs on dead cpu.  Requires new
tasklet_kill_immediate for RCU to clean up its tasklet (which might
have been about to run, so tasklet_kill won't work).

Change the migration thread to directly use its cpu arg, rather than
smp_processor_id(): if a cpu goes up then down rapidly, it can be on
the wrong cpu just before it is stopped.

Add code to stop the migration thread on CPU_DEAD and CPU_UP_CANCELED.

Remove the (bogus) priority of the notifier.

We need the migration thread to be RT as soon as the CPU comes online:
for example, stop_machine() (another RT task) expects to yield to it.
Extract the core of setscheduler() and do that when the migration
thread is created.  rq lock is a precaution against the (theoretical)
possibility of someone else doing setscheduer on this thread at the
same time.