Add VID:DID for Lenovo OneLinkDock Gigabit LAN
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ding Tianhong says:

====================
Fix RTNL: assertion failed at net/core/rtnetlink.c

The commit 1d3ee88a
(bonding: add netlink attributes to slave link dev)
make the bond_set_active_slave() and bond_set_backup_slave()
use rtmsg_ifinfo to send slave's states and this functions
should be called in RTNL.

But the 902.3ad and ARP monitor did not hold the RTNL when calling
thses two functions, so fix them.

v1->v2: Add new micro to indicate that the notification should be send
        later, not never.
        And add a new patch to fix the same problem for ARP mode.

v2->v3: modify the bond_should_notify to should_notify_rtnl, it is more
	reasonable, and	use bool for should_notify_rtnl.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Veaceslav has reported and fix this problem by commit f2ebd477
(bonding: restructure locking of bond_ab_arp_probe()). According Jay's
opinion, the current solution is not very well, because the notification
is to indicate that the interface has actually changed state in a meaningful
way, but these calls in the ab ARP monitor are internal settings of the flags
to allow the ARP monitor to search for a slave to become active when there are
no active slaves. The flag setting to active or backup is to permit the ARP
monitor's response logic to do the right thing when deciding if the test
slave (current_arp_slave) is up or not.

So the best way to fix the problem is that we should not send a notification
when the slave is in testing state, and check the state at the end of the
monitor, if the slave's state recover, avoid to send pointless notification
twice. And RTNL is really a big lock, hold it regardless the slave's state
changed or not when the current_active_slave is null will loss performance
(every 100ms), so we should hold it only when the slave's state changed and
need to notify.

I revert the old commit and add new modifications.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The problem was introduced by the commit 1d3ee88a
(bonding: add netlink attributes to slave link dev).
The bond_set_active_slave() and bond_set_backup_slave()
will use rtmsg_ifinfo to send slave's states, so these
two functions should be called in RTNL.

In 802.3ad mode, acquiring RTNL for the __enable_port and
__disable_port cases is difficult, as those calls generally
already hold the state machine lock, and cannot unconditionally
call rtnl_lock because either they already hold RTNL (for calls
via bond_3ad_unbind_slave) or due to the potential for deadlock
with bond_3ad_adapter_speed_changed, bond_3ad_adapter_duplex_changed,
bond_3ad_link_change, or bond_3ad_update_lacp_rate.  All four of
those are called with RTNL held, and acquire the state machine lock
second.  The calling contexts for __enable_port and __disable_port
already hold the state machine lock, and may or may not need RTNL.

According to the Jay's opinion, I don't think it is a problem that
the slave don't send notify message synchronously when the status
changed, normally the state machine is running every 100 ms, send
the notify message at the end of the state machine if the slave's
state changed should be better.

I fix the problem through these steps:

1). add a new function bond_set_slave_state() which could change
    the slave's state and call rtmsg_ifinfo() according to the input
    parameters called notify.

2). Add a new slave parameter which called should_notify, if the slave's state
    changed and don't notify yet, the parameter will be set to 1, and then if
    the slave's state changed again, the param will be set to 0, it indicate that
    the slave's state has been restored, no need to notify any one.

3). the __enable_port and __disable_port should not call rtmsg_ifinfo
    in the state machine lock, any change in the state of slave could
    set a flag in the slave, it will indicated that an rtmsg_ifinfo
    should be called at the end of the state machine.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new F: line for the intel subdirectories.

This allows get_maintainers to avoid using git log
and cc'ing people that have submitted clean-up style
patches for all first level directories under
drivers/net/ethernet/intel/

This does not make e100.c maintained.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we receive a PTP event from the NIC when we haven't set up PTP state
in the driver, we attempt to read through a NULL pointer efx->ptp_data,
triggering a panic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While LINUX_MIB_TCPSPURIOUS_RTX_HOSTQUEUES can only be incremented
in tcp_transmit_skb() from softirq (incoming message or timer
activation), it is better to use NET_INC_STATS() instead of
NET_INC_STATS_BH() as tcp_transmit_skb() can be called from process
context.

This will avoid copy/paste confusion when/if we want to add
other SNMP counters in tcp_transmit_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Masking the link partner's capabilities with local capabilities can be
misleading in autonegotiation scenarios such as PAUSE frame
autonegotiation.
This patch calculates the join between the local capabilities and the
link parner capabilities, when it determines the speed and duplex
settings, but does not mask any of the link partner capabilities when
it calculates PAUSE frame settings.
Signed-off-by: Cristian Bercaru <cristian.bercaru@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink_sendmsg() was changed to prevent non-root processes from sending
messages with dst_pid != 0.
netlink_connect() however still only checks if nladdr->nl_groups is set.
This patch modifies netlink_connect() to check for the same condition.
Signed-off-by: Mike Pecovnik <mike.pecovnik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without a shutdown handler, T4 cards behave very badly after a kexec.
Some firmware calls return errors indicating allocation failures, for
example. This is probably because thouse resources were not released by
a BYE message to the firmware, for example.

Using the remove handler guarantees we will use a well tested path.

With this patch I applied, I managed to use kexec multiple times and
probe and iSCSI login worked every time.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
qlcnic: Bug fixes

This patch series includes following bug fixes,

* Fix for return value handling of function qlcnic_enable_msi_legacy().
* Fix for the usage of module parameters for interrupt mode.
  Driver should use flags while checking for driver's interrupt mode instead of
  module parameters.
* Revert commit 1414abea (qlcnic: Restrict VF from configuring any VLAN mode),
  in order to save some multicast filters.
* Fix a bug where driver was not re-setting sds ring count to 1 when
  it falls back from MSI-x mode to legacy interrupt mode.

Please apply to net.

Change in v2 -
Dropped patch "qlcnic: reset firmware API lock during driver load" for further rework.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

o Driver was not re-setting sds ring count to 1 after failing
   to allocate msi-x interrupts.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o This patch reverts commit 1414abea
  (qlcnic: Restrict VF from configuring any VLAN mode.)
  This will allow same multicast address to be used with any VLAN
  instead of programming seperate (MAC, VLAN) tuples in adapter.
  This will help save some multicast filters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once interrupts are enabled, instead of using module parameters,
use flags (QLCNIC_MSI_ENABLED and QLCNIC_MSIX_ENABLED) set by driver
to check interrupt mode.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver was treating -ve return value as success in case of
qlcnic_enable_msi_legacy() failure
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To guarantee that a qdio ccw_device no longer touches the
qdio memory shared with Linux, the qdio ccw_device should
be offline when freeing the qdio memory. Thus this patch
postpones freeing of qdio memory.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the UFO fragmentation process does not correctly handle inner
UDP frames.

(The following tcpdumps are captured on the parent interface with ufo
disabled while tunnel has ufo enabled, 2000 bytes payload, mtu 1280,
both sit device):

IPv6:
16:39:10.031613 IP (tos 0x0, ttl 64, id 3208, offset 0, flags [DF], proto IPv6 (41), length 1300)
    192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 1240) 2001::1 > 2001::8: frag (0x00000001:0|1232) 44883 > distinct: UDP, length 2000
16:39:10.031709 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPv6 (41), length 844)
    192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 784) 2001::1 > 2001::8: frag (0x00000001:0|776) 58979 > 46366: UDP, length 5471

We can see that fragmentation header offset is not correctly updated.
(fragmentation id handling is corrected by 916e4cf4 ("ipv6: reuse
ip6_frag_id from ip6_ufo_append_data")).

IPv4:
16:39:57.737761 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPIP (4), length 1296)
    192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57034, offset 0, flags [none], proto UDP (17), length 1276)
    192.168.99.1.35961 > 192.168.99.2.distinct: UDP, length 2000
16:39:57.738028 IP (tos 0x0, ttl 64, id 3210, offset 0, flags [DF], proto IPIP (4), length 792)
    192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57035, offset 0, flags [none], proto UDP (17), length 772)
    192.168.99.1.13531 > 192.168.99.2.20653: UDP, length 51109

In this case fragmentation id is incremented and offset is not updated.

First, I aligned inet_gso_segment and ipv6_gso_segment:
* align naming of flags
* ipv6_gso_segment: setting skb->encapsulation is unnecessary, as we
  always ensure that the state of this flag is left untouched when
  returning from upper gso segmenation function
* ipv6_gso_segment: move skb_reset_inner_headers below updating the
  fragmentation header data, we don't care for updating fragmentation
  header data
* remove currently unneeded comment indicating skb->encapsulation might
  get changed by upper gso_segment callback (gre and udp-tunnel reset
  encapsulation after segmentation on each fragment)

If we encounter an IPIP or SIT gso skb we now check for the protocol ==
IPPROTO_UDP and that we at least have already traversed another ip(6)
protocol header.

The reason why we have to special case GSO_IPIP and GSO_SIT is that
we reset skb->encapsulation to 0 while skb_mac_gso_segment the inner
protocol of GSO_UDP_TUNNEL or GSO_GRE packets.
Reported-by: Wolfgang Walter <linux@stwm.de>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bump all Mellanox driver versions.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Boris reports he's seeing:
> [    9.195943] INFO: trying to register non-static key.
> [    9.196031] the code is fine but needs lockdep annotation.
> [    9.196031] turning off the locking correctness validator.
> [    9.196031] CPU: 1 PID: 933 Comm: modprobe Not tainted 3.14.0-rc4+ #1
with the r8169 driver.

These are occuring because the seqcount embedded in u64_stats_sync on
32-bit SMP is uninitialized which is making lockdep unhappy.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_is_cwnd_limited() allows GSO/TSO enabled flows to increase
their cwnd to allow a full size (64KB) TSO packet to be sent.

Non GSO flows only allow an extra room of 3 MSS.

For most flows with a BDP below 10 MSS, this results in a bloat
of cwnd reaching 90, and an inflate of RTT.

Thanks to TSO auto sizing, we can restrict the bloat to the number
of MSS contained in a TSO packet (tp->xmit_size_goal_segs), to keep
original intent without performance impact.

Because we keep cwnd small, it helps to keep TSO packet size to their
optimal value.

Example for a 10Mbit flow, with low TCP Small queue limits (no more than
2 skb in qdisc/device tx ring)

Before patch :

lpk51:~# ./ss -i dst lpk52:44862 | grep cwnd
         cubic wscale:6,6 rto:215 rtt:15.875/2.5 mss:1448 cwnd:96
ssthresh:96
send 70.1Mbps unacked:14 rcv_space:29200

After patch :

lpk51:~# ./ss -i dst lpk52:52916 | grep cwnd
         cubic wscale:6,6 rto:206 rtt:5.206/0.036 mss:1448 cwnd:15
ssthresh:14
send 33.4Mbps unacked:4 rcv_space:29200
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Van Jacobson <vanj@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alloc_dma_desc_resources() returns an error value and the next line
actually checks for it, so assign the return value properly.

Found by the coverity scanner.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should alloc big buffers also when guest can receive UFO
packets to let the big packets fit into guest rx buffer.

Fixes 5c516751
(virtio-net: Allow UFO feature to be set and advertised.)

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we generate a new fragmentation id on UFO segmentation. It
is pretty hairy to identify the correct net namespace and dst there.
Especially tunnels use IFF_XMIT_DST_RELEASE and thus have no skb_dst
available at all.

This causes unreliable or very predictable ipv6 fragmentation id
generation while segmentation.

Luckily we already have pregenerated the ip6_frag_id in
ip6_ufo_append_data and can use it here.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Problem statement: 1) both paths (primary path1 and alternate
path2) are up after the association has been established i.e.,
HB packets are normally exchanged, 2) path2 gets inactive after
path_max_retrans * max_rto timed out (i.e. path2 is down completely),
3) now, if a transmission times out on the only surviving/active
path1 (any ~1sec network service impact could cause this like
a channel bonding failover), then the retransmitted packets are
sent over the inactive path2; this happens with partial failover
and without it.

Besides not being optimal in the above scenario, a small failure
or timeout in the only existing path has the potential to cause
long delays in the retransmission (depending on RTO_MAX) until
the still active path is reselected. Further, when the T3-timeout
occurs, we have active_patch == retrans_path, and even though the
timeout occurred on the initial transmission of data, not a
retransmit, we end up updating retransmit path.

RFC4960, section 6.4. "Multi-Homed SCTP Endpoints" states under
6.4.1. "Failover from an Inactive Destination Address" the
following:

  Some of the transport addresses of a multi-homed SCTP endpoint
  may become inactive due to either the occurrence of certain
  error conditions (see Section 8.2) or adjustments from the
  SCTP user.

  When there is outbound data to send and the primary path
  becomes inactive (e.g., due to failures), or where the SCTP
  user explicitly requests to send data to an inactive
  destination transport address, before reporting an error to
  its ULP, the SCTP endpoint should try to send the data to an
  alternate __active__ destination transport address if one
  exists.

  When retransmitting data that timed out, if the endpoint is
  multihomed, it should consider each source-destination address
  pair in its retransmission selection policy. When retransmitting
  timed-out data, the endpoint should attempt to pick the most
  divergent source-destination pair from the original
  source-destination pair to which the packet was transmitted.

  Note: Rules for picking the most divergent source-destination
  pair are an implementation decision and are not specified
  within this document.

So, we should first reconsider to take the current active
retransmission transport if we cannot find an alternative
active one. If all of that fails, we can still round robin
through unkown, partial failover, and inactive ones in the
hope to find something still suitable.

Commit 4141ddc0 ("sctp: retran_path update bug fix") broke
that behaviour by selecting the next inactive transport when
no other active transport was found besides the current assoc's
peer.retran_path. Before commit 4141ddc0, we would have
traversed through the list until we reach our peer.retran_path
again, and in case that is still in state SCTP_ACTIVE, we would
take it and return. Only if that is not the case either, we
take the next inactive transport.

Besides all that, another issue is that transports in state
SCTP_UNKNOWN could be preferred over transports in state
SCTP_ACTIVE in case a SCTP_ACTIVE transport appears after
SCTP_UNKNOWN in the transport list yielding a weaker transport
state to be used in retransmission.

This patch mostly reverts 4141ddc0, but also rewrites
this function to introduce more clarity and strictness into
the code. A strict priority of transport states is enforced
in this patch, hence selection is active > unkown > partial
failover > inactive.

Fixes: 4141ddc0 ("sctp: retran_path update bug fix")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Acked-by: Vlad Yasevich <yasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes bug introduced by:
commit 1d4c8c29
"neigh: restore old behaviour of default parms values"

The thing is that in neigh_sysctl_register, extra1 and extra2 which were
previously set for NEIGH_VAR_GC_* are overwritten. That leads to
nonsense int limits for gc_* variables. So fix this by not touching
extra* fields for gc_* variables.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes two bugs in fastopen :

1) The tcp_sendmsg(...,  @size) argument was ignored.

   Code was relying on user not fooling the kernel with iovec mismatches

2) When MTU is about 64KB, tcp_send_syn_data() attempts order-5
allocations, which are likely to fail when memory gets fragmented.

Fixes: 783237e8 ("net-tcp: Fast Open client - sending SYN-data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Tested-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ying Xue says:

====================
tipc: clean up components initialization code

In this series, we will fix a regression issue involved by commit
6e967adf(tipc: relocate common functions from media to bearer)
But before the issue is fixed, we firstly adjust the process of
components initialization so as to remove all enabled flags from
necessary tipc components. Otherwise, without the change, we also
have to add an extra enabled flag into bearer layer indicating
whether bearer setup is finshed or not.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Accidentally a side effect is involved by commit 6e967adf(tipc:
relocate common functions from media to bearer). Now tipc stack
handler of receiving packets from netdevices as well as netdevice
notification handler are registered when bearer is enabled rather
than tipc module initialization stage, but the two handlers are
both unregistered in tipc module exit phase. If tipc module is
inserted and then immediately removed, the following warning
message will appear:

"dev_remove_pack: ffffffffa0380940 not found"

This is because in module insertion stage tipc stack packet handler
is not registered at all, but in module exit phase dev_remove_pack()
needs to remove it. Of course, dev_remove_pack() cannot find tipc
protocol handler from the kernel protocol handler list so that the
warning message is printed out.

But if registering the two handlers is adjusted from enabling bearer
phase into inserting module stage, the warning message will be
eliminated. Due to this change, tipc_core_start_net() and
tipc_core_stop_net() can be deleted as well.
Reported-by: Wang Weidong <wangweidong1@huawei.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When tipc module is inserted, many tipc components are initialized
one by one. During the initialization period, if one of them is
failed, tipc_core_stop() will be called to stop all components
whatever corresponding components are created or not. To avoid to
release uncreated ones, relevant components have to add necessary
enabled flags indicating whether they are created or not.

But in the initialization stage, if one component is unsuccessfully
created, we will just destroy successfully created components before
the failed component instead of all components. All enabled flags
defined in components, in turn, become redundant. Additionally it's
also unnecessary to identify whether table.types is NULL in
tipc_nametbl_stop() because name stable has been definitely created
successfully when tipc_nametbl_stop() is called.

Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In current implementation it is possible to reach PF state from unconfirmed.
We can interpret sctp-failover-02 in a way that PF state is meant to be reached
only from active state, in the end, this is when entering PF state makes sense.
Here are few quotes from sctp-failover-02, but regardless of these, same
understanding can be reached from whole section 5:

Section 5.1, quickfailover guide:
    "The PF state is an intermediate state between Active and Failed states."

    "Each time the T3-rtx timer expires on an active or idle
    destination, the error counter of that destination address will
    be incremented.  When the value in the error counter exceeds
    PFMR, the endpoint should mark the destination transport address as PF."

There are several concrete reasons for such interpretation. For start, rfc4960
does not take into concern quickfailover algorithm. Therefore, quickfailover
must comply to 4960. Point where this compliance can be argued is following
behavior:
When PF is entered, association overall error counter is incremented for each
missed HB. This is contradictory to rfc4960, as address, while in unconfirmed
state, is subjected to probing, and while it is probed, it should not increment
association overall error counter. This has as a consequence that we might end
up in situation in which we drop association due path failure on unconfirmed
address, in case we have wrong configuration in a way:
Association.Max.Retrans == Path.Max.Retrans.

Another reason is that entering PF from unconfirmed will cause a loss of address
confirmed event when address is once (if) confirmed. This is fine from failover
guide point of view, but it is not consistent with behavior preceding failover
implementation and recommendation from 4960:

5.4.  Path Verification
   Whenever a path is confirmed, an indication MAY be given to the upper
   layer.
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current flow: Set TX BD ready, and then set "INT" and "PINS" bit to
enable tx interrupt generation and crc checksum.

There has potential issue like as:
CPU			fec uDMA
Set tx ready bit
			uDMA start the BD transmission
Set "INT" bit
Set "PINS" bit
...

Above situation cause fec tx interrupt lost and fec MAC don't do
CRC checksum. The patch fix the potential issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <Frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug introduced by commit 7d442fab ("ipv4: Cache dst in tunnels").

Because sit code does not call ip_tunnel_init(), the dst_cache was not
initialized.

CC: Tom Herbert <therbert@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even though only the outer vlan tag can be HW accelerated in the transmission
path, in the TUN/TAP driver vlan_features mirrors hw_features, which happens
to have the NETIF_F_HW_VLAN_?TAG_TX flags set. Because of this, during packet
tranmisssion through a stacked vlan device dev_hard_start_xmit, (incorrectly)
assuming that the vlan device supports hardware vlan acceleration, does not
add the vlan header to the skb payload and the inner vlan tags are lost
(vlan_tci contains the outer vlan tag when userspace reads the packet from
the tap device).
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even if we create a stacked vlan interface such as veth0.10.20, it sends
single tagged frames (tagged with only vid 10).
Because vlan_features of a veth interface has the
NETIF_F_HW_VLAN_[CTAG/STAG]_TX bits, veth0.10 also has that feature, so
dev_hard_start_xmit(veth0.10) doesn't call __vlan_put_tag() and
vlan_dev_hard_start_xmit(veth0.10) overwrites vlan_tci.
This prevents us from using a combination of 802.1ad and 802.1Q
in containers, etc.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/built-in.o:(.rodata+0x1707c): undefined reference to `ip_tunnel_get_stats64'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ed1f50c3 ("net: add skb_checksum_setup") we introduced some checksum
functions in core driver. Subsequent change b5cf66cd ("xen-netfront:
use new skb_checksum_setup function") made use of those functions to
replace its own implementation.

However with that change netfront is broken. It sees a lot of checksum
error. That's because its own implementation of checksum function was a
bit hacky (dereferencing skb->data directly) while the new function was
implemented using ip_hdr(). The network header is not reset before skb
is passed to the new function. When the new function tries to do its
job, it's confused and reports error.

The fix is simple, we need to reset network header before passing skb to
checksum function. Netback is not affected as it already does the right
thing.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Tested-By: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

* Fix nf_trace in nftables if XT_TRACE=n, from Florian Westphal.

* Don't use the fast payload operation in nf_tables if the length is
  not power of 2 or it is not aligned, from Nikolay Aleksandrov.

* Fix missing break statement the inet flavour of nft_reject, which
  results in evaluating IPv4 packets with the IPv6 evaluation routine,
  from Patrick McHardy.

* Fix wrong kconfig symbol in nft_meta to match the routing realm,
  from Paul Bolle.

* Allocate the NAT null binding when creating new conntracks via
  ctnetlink to avoid that several packets race at initializing the
  the conntrack NAT extension, original patch from Florian Westphal,
  revisited version from me.

* Fix DNAT handling in the snmp NAT helper, the same handling was being
  done for SNAT and DNAT and 2.4 already contains that fix, from
  Francois-Xavier Le Bail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm fixes from Dave Airlie:
 "Lots of little small things, nothing too major: nouveau regression
  fixes, vmware fixes for the new hw support, memory leaks in error path
  fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
  drm/radeon/ni: fix typo in dpm sq ramping setup
  drm/radeon/si: fix typo in dpm sq ramping setup
  drm/radeon: fix CP semaphores on CIK
  drm/radeon: delete a stray tab
  drm/radeon: fix display tiling setup on SI
  drm/radeon/dpm: reduce r7xx vblank mclk threshold to 200
  drm/radeon: fill in DRM_CAPs for cursor size
  drm: add DRM_CAPs for cursor size
  drm/radeon: unify bpc handling
  drm/ttm: Fix memory leak in ttm_agp_backend.c
  drm/ttm: declare 'struct device' in ttm_page_alloc.h
  drm/nouveau: fix TTM_PL_TT memtype on pre-nv50
  drm/nv50/disp: use correct register to determine DP display bpp
  drm/nouveau/fb: use correct ram oclass for nv1a hardware
  drm/nv50/gr: add missing nv_error parameter priv
  drm/nouveau: fix ENG_RUNLIST register address
  drm/nv4c/bios: disallow retrieving from prom on nv4x igp's
  drm/nv4c/vga: decode register is in a different place on nv4x igp's
  drm/nv4c/mc: nv4x igp's have a different msi rearm register
  drm/nouveau: set irq_enabled manually
  ...

Pull HID update from Jiri Kosina:

 - fixes for several bugs in incorrect allocations of buffers by David
   Herrmann and Benjamin Tissoires.

 - support for a few new device IDs by Archana Patni, Benjamin
   Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: hyperv: make sure input buffer is big enough
  HID: Bluetooth: hidp: make sure input buffers are big enough
  HID: hid-sensor-hub: quirk for STM Sensor hub
  HID: apple: add Apple wireless keyboard 2011 JIS model support
  HID: fix buffer allocations
  HID: multitouch: add FocalTech FTxxxx support
  HID: microsoft: Add ID's for Surface Type/Touch Cover 2
  HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay