Per simple-card.yaml, 'simple-audio-card,audio-routing' is not a valid
property.

Change it to 'simple-audio-card,routing'.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Wifi chip description, which causes the following schema warning:

imx6q-prti6q.dtb: mmc@2194000: Unevaluated properties are not allowed ('wifi' was unexpected)

Pass the missing items to fix it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass 'mmc' as the esdhc node names to fix the following schema
warnings:

vf610-cosmic.dtb: esdhc@400b1000: $nodename:0: 'esdhc@400b1000' does not match '^mmc(@.*)?$'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

"st,m25p" is not a valid compatible according to jedec,spi-nor.yaml.

Remove it.

Also, node names should be generic, so use 'flash' as the SPI NOR flash
node name.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Node names should be generic, so use 'flash' as the SPI NOR flash node
name.

This fixes the following schema warning:

imx53-smd.dtb: m25p32@1: $nodename:0: 'm25p32@1' does not match '^(flash|.*sram|nand)(@.*)?$'
	from schema $id: http://devicetree.org/schemas/mtd/jedec,spi-nor.yaml#Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

"st,m25p" is not a valid compatible according to jedec,spi-nor.yaml.

Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The bootloader does not add the partitions into DT, so add them manually
here.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device tree for the MBLS102xA mainboard with TQMLS1021A SoM.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Passing the 'compatible' property inside the pfuze100 regulator nodes
is not allowed per pfuze100.yaml and results in the following
warning:

imx6q-bosch-acc.dtb: pmic@8: regulators:sw3a: Unevaluated properties are not allowed ('compatible' was unexpected)

Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As per sgtl5000.yaml, '#sound-dai-cells' is a required property.

Pass it to fix the following schema warnings:

imx53-mba53.dtb: sgtl5000@a: '#sound-dai-cells' is a required property
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Each interrupt should be in its own cell.  This is much more readable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As per sgtl5000.yaml, 'clock-names' is not a valid property.

Remove it to fix the following schema warning:

imx6ul-isiot-nand.dtb: codec@a: Unevaluated properties are not allowed ('clock-names' was unexpected)
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixed regulators are not in some bus and bindings do not allow a "reg"
property.  Move them out of "regulators" node to top-level.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixed regulators are not in some bus and bindings do not allow a "reg"
property.  Move them out of "regulators" node to top-level.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixed regulators are not in some bus and bindings do not allow a "reg"
property.  Move them out of "regulators" node to top-level.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixed regulators are not in some bus and bindings do not allow a "reg"
property.  Move them out of "regulators" node to top-level.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The recommended name for enable GPIOs property in regulator-gpio is
"enable-gpios".  This is also required by bindings:

  imx50-kobo-aura.dtb: gpio-regulator: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixed regulators put under "regulators" node will not be populated,
unless simple-bus or something similar is used.  Drop the "regulators"
wrapper node to fix this.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

regulator-fixed-clock does not take "regulator-type" property:

  imx6ull-colibri-iris-v2.dtb: regulator-eth-phy: Unevaluated properties are not allowed ('regulator-type' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

regulator-fixed does not take "clock-names" property:

  imx6sx-nitrogen6sx.dtb: regulator-wlan: Unevaluated properties are not allowed ('clock-names' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

MX53_PAD_GPIO_1__PWM2_PWMO controls the backlight of the parallel
Seiko display and MX53_PAD_EIM_D24__GPIO3_24 controls the display power.

Reflect that in the devicetree for better description of the board.

Without these entries there is no LCD output on the Seiko display, unless
the bootloader has previously configured these pins.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use id-gpios and vbus-gpios instead.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixes the warning:
lm75 0-0048: supply vs not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Due to the missing signal connection between i.MX6 WDOG_B pin and the
PMICs external reset, the internal i.MX6 watchdog is not able to reset
the phyCORE i.MX6 SoM properly. Thus disable the internal i.MX6 watchdog
to prevent unexpected PMIC settings after reset.

NOTE: This patch should not be backported as it might break existing
uses and fixes in bootloaders.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Stefan Riedmüller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Due to the missing signal connection between i.MX6 WDOG_B pin and the
PMICs external reset, the internal i.MX6 watchdog is not able to reset
the phyFLEX SoM properly. Thus disable the internal i.MX6 watchdog to
prevent unexpected PMIC settings after reset.

NOTE: This patch should not be backported as it might break existing
uses and fixes in bootloaders.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Stefan Riedmüller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

A suitable default for the LCDIF parent is the PLL5 clock, so
describe it in the device tree.

The imx6sx clock driver harcodes PLL5 as the LCDIF1 parent, but
in preparation for removing such hardcoding, describe the parent
relationship via devicetree.

There are some boards that may want to use a different parent
for the LCDIF due to EMI reasons, for example.

With this approch, the user can change the LCDIF parent in the board
devicetree if needed.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixes the warnings:
at24 0-0057: supply vcc not found, using dummy regulator
lm75 0-0049: supply vs not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The davicom,dm9000 Ethernet Controller accepts two reg addresses.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Describe the Ethernet aliases so that the second MAC address
can be retrieved from the bootloader.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add missing whitespace between node name/label and opening {.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Regulators should not be placed under simple-bus.

Move it outside simple-bus to fix the following schema warnings:

regulators: $nodename:0: 'regulators' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
From schema: site-packages/dtschema/schemas/simple-bus.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Instead of using 0x80000000 explicitly specify the reset defaults for
the pad settings. This way the pad configuration is explicit and so
isn't affected by changes that might have been done in the bootloader.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.

The answer is "No. No we cannot".

I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street.  And at the yearly
maintainer summit, we will all sing the alphabet song together.

I doubt I will keep doing this.  At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.

Repeats: 80e62bc8 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull dma-mapping fixes from Christoph Hellwig:

 - swiotlb area sizing fixes (Petr Tesarik)

* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: reduce the number of areas to match actual memory pool size
  swiotlb: always set the number of areas before allocating the pool

Pull irq update from Borislav Petkov:

 - Optimize IRQ domain's name assignment

* tag 'irq_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqdomain: Use return value of strreplace()

Pull x86 fpu fix from Borislav Petkov:

 - Do FPU AP initialization on Xen PV too which got missed by the recent
   boot reordering work

* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/xen: Fix secondary processors' FPU initialization

Pull x86 fix from Thomas Gleixner:
 "A single fix for the mechanism to park CPUs with an INIT IPI.

  On shutdown or kexec, the kernel tries to park the non-boot CPUs with
  an INIT IPI. But the same code path is also used by the crash utility.
  If the CPU which panics is not the boot CPU then it sends an INIT IPI
  to the boot CPU which resets the machine.

  Prevent this by validating that the CPU which runs the stop mechanism
  is the boot CPU. If not, leave the other CPUs in HLT"

* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smp: Don't send INIT to boot CPU

Pull MIPS fixes from Thomas Bogendoerfer:

 - fixes for KVM

 - fix for loongson build and cpu probing

 - DT fixes

* tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
  MIPS: dts: add missing space before {
  MIPS: Loongson: Fix build error when make modules_install
  MIPS: KVM: Fix NULL pointer dereference
  MIPS: Loongson: Fix cpu_probe_loongson() again

Pull xfs fix from Darrick Wong:
 "Nothing exciting here, just getting rid of a gcc warning that I got
  tired of seeing when I turn on gcov"

* tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix uninit warning in xfs_growfs_data