Jeroen de Borst says:

====================
gve: minor code and performance improvements

This patchset contains a number of independent minor code and performance
improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The rx_buf_alloc_fail counter wasn't getting updated.

Fixes: 433e274b ("gve: Add stats for gve.")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Half pages are just used for small enough packets. This change allows
this to also apply for systems with pages larger than 4 KB.

Fixes: 02b0e0c1 ("gve: Rx Buffer Recycling")
Signed-off-by: Jordan Kim <jrkim@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Configure XPS when adding tx queues to the notification blocks.

Fixes: dbdaa675 ("gve: Move some static functions to a common file")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't always reset the driver on a TX timeout. Attempt to
recover by kicking the queue in case an IRQ was missed.

Fixes: 9e5f7d26 ("gve: Add workqueue and reset support")
Signed-off-by: John Fraker <jfraker@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When TX queue is full, attemt to process enough TX completions
to avoid stalling the queue.

Fixes: f5cedc84 ("gve: Add transmit and receive support")
Signed-off-by: Tao Liu <xliutaox@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a pagecnt bias field to rx buffer info struct to eliminate
needing to increment the atomic page ref count on every pass in the
rx hotpath.

Also prefetch two packet pages ahead.

Fixes: ede3fcf5 ("gve: Add support for raw addressing to the rx path")
Signed-off-by: Yanchun Fu <yangchun@google.com>
Signed-off-by: Nathan Lewis <npl@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use napi_complete_done to allow for the use of gro_flush_timeout.

Fixes: f5cedc84 ("gve: Add transmit and receive support")
Signed-off-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix for this build problem:

drivers/net/ethernet/sun/ldmvsw.c: In function 'vsw_alloc_netdev':
drivers/net/ethernet/sun/ldmvsw.c:243:2: error: expected ';' before 'sprintf'
  sprintf(dev->name, "vif%d.%d", (int)handle, (int)port_id);
  ^~~~~~~

Fixes: a7639279 ("ethernet: sun: remove direct netdev->dev_addr writes")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20211011173424.7743035d@canb.auug.org.auSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This patch separates the logic of configuring hardware
maximum transmit frame size and receive frame size.
This simplifies the logic to calculate receive buffer
size and using cqe descriptor of different size.
Also additional size of skb_shared_info structure is
allocated for each receive buffer pointer given to
hardware which is not necessary. Hence change the
size calculation to remove the size of
skb_shared_info. Add a check for array out of
bounds while adding fragments to the network stack.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.

Remove the redundant 'flush_workqueue()' calls.

This was generated with coccinelle:

@@
expression E;
@@
- 	flush_workqueue(E);
	destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> #mlx*
Signed-off-by: David S. Miller <davem@davemloft.net>

networking benchmark shows that __rcu_read_lock and
__rcu_read_unlock takes some cpu cycles, and we can avoid
calling them partially in virtio rx path by check xdp_enabled
of vi, and xdp is disabled most of time
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cosmetic commit making dev_get_port_parent_id slightly more readable.
There is no need to split the condition to return after calling
devlink_compat_switch_id_get and after that 'recurse' is always true.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Give a name to known debug regs from Documentation instead of using
unknown hex values.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

From original QCA source code the port was set to prefer master as port
type in 1000BASE-T mode. Apply the same settings also here.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

QCA8327 internal phy require DAC amplitude adjustement set to +6% with
100m speed. Also add additional define to report a change of the same
reg in QCA8337. (different scope it does set 1000m voltage)
Add link_change_notify function to set the proper amplitude adjustement
on PHY_RUNNING state and disable on any other state.

Fixes: b4df02b5 ("net: phy: at803x: add support for qca 8327 A variant internal phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From Documentation phy resume triggers phy reset and restart
auto-negotiation. Add a dedicated function to wait reset to finish as
it was notice a regression where port sometime are not reliable after a
suspend/resume session. The reset wait logic is copied from phy_poll_reset.
Add dedicated suspend function to use genphy_suspend only with QCA8337
phy and set only additional debug settings for QCA8327. With more test
it was reported that QCA8327 doesn't proprely support this mode and
using this cause the unreliability of the switch ports, especially the
malfunction of the port0.

Fixes: 15b9df4e ("net: phy: at803x: add resume/suspend function to qca83xx phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Juhee Kang says:

====================
net-next: replace open code with helper functions

Currently, there are many helper functions on netdevice.h. However,
some code doesn't use the helper functions and remains open code.
So this patchset replaces open code with an appropriate helper function.

First patch modifies to use netif_is_rxfh_configured instead of
dev->priv_flags & IFF_RXFH_CONFIGURED.
Second patch replaces open code with netif_is_bond_master.
Last patch substitutes netif_is_macsec() for dev->priv_flags & IFF_MACSEC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Open code which is dev->priv_flags & IFF_MACSEC has already defined as
netif_is_macsec(). So use netif_is_macsec() instead of open code.
This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netif_is_bond_master() function instead of open code, which is
((event_dev->priv_flags & IFF_BONDING) && (event_dev->flags & IFF_MASTER)).
This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The open code which is dev->priv_flags & IFF_RXFH_CONFIGURED is defined as
a helper function on netdevice.h. So use netif_is_rxfh_configured()
function instead of open code. This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: add vlanid overflow management

Add vlans to the existing rx_filter_sync mechanics currently
used for managing mac filters.

Older versions of our firmware had no enforced limits on the
number of vlans that the driver could request, but requesting
large numbers of vlans caused issues in FW memory management,
so an arbitrary limit was added in the FW.  The FW now
returns -ENOSPC when it hits that limit, which the driver
needs to handle.

Unfortunately, the FW doesn't advertise the vlan id limit,
as it does with mac filters, so the driver won't know the
limit until it bumps into it.  We'll grab the current vlan id
count and use that as the limit from there on and thus prevent
getting any more -ENOSPC errors.

Just as is done for the mac filters, the device puts the device
into promiscuous mode when -ENOSPC is seen for vlan ids, and
the driver will track the vlans that aren't synced to the FW.
When vlans are removed, the driver will retry the un-synced
vlans.  If all outstanding vlans are synced, the promiscuous
mode will be disabled.

The first 6 patches rework the existing filter management to
make it flexible enough for additional filter types.  Next
we add the vlan ids into the management.  The last 2 patches
allow us to catch the max vlan -ENOSPC error without adding
an unnecessary error message to the kernel log.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Override the automatic AdminQ error message in order to
capture the potential No Space message when we hit the
max vlan limit, and add additional messaging to detail
what filter failed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AdminQ handler has an error handler that automatically prints
an error message when the request has failed.  However, there are
situations where the caller can expect that it might fail and has
an alternative strategy, thus may not want the error message sent
to the log, such as hitting -ENOSPC when adding a new vlan id.

We add a new interface to the AdminQ API to allow for override of
the default behavior, and an interface to the use standard error
message formatting.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add vlans to the existing rx_filter_sync mechanics currently
used for managing mac filters.

Older versions of our firmware had no enforced limits on the
number of vlans that the LIF could request, but requesting large
numbers of vlans caused issues in FW memory management, so an
arbitrary limit was added in the FW.  The FW now returns -ENOSPC
when it hits that limit, which the driver needs to handle.

Unfortunately, the FW doesn't advertise the vlan id limit,
as it does with mac filters, so the driver won't know the
limit until it bumps into it.  We'll grab the current vlan id
count and use that as the limit from there on and thus prevent
getting any more -ENOSPC errors.

Just as is done for the mac filters, the device puts the device
into promiscuous mode when -ENOSPC is seen for vlan ids, and
the driver will track the vlans that aren't synced to the FW.
When vlans are removed, the driver will retry the un-synced
vlans.  If all outstanding vlans are synced, the promiscuous
mode will be disabled.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the filter add, make a generic filter delete.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for adding vlan overflow management, rework
the ionic_lif_addr_add() function to something a little more
generic that can be used for other filter types.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for enhancing vlan filter management,
add a filter search routine that can figure out for
itself which type of filter search is needed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The overflow flags really aren't useful and we don't need lif
struct elements to track them.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The routines that add and delete mac addresses from the
firmware really should be in the file with the rest of
the filter management.  This simply moves the functions
with no logic changes.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dump the filter list to debugfs - includes the device-assigned
filter id and the sync'd-to-hardware status.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Vitesse/Microsemi/Microchip family of switches supported by the
Felix DSA driver is capable of selecting between the native tagging
protocol and ocelot-8021q. This is necessary to enable flow control on
the CPU port.

Certain systems where these switches are integrated use the switch as a
port multiplexer, so the termination throughput is paramount. Changing
the tagging protocol at runtime is possible for these systems, but since
it is known beforehand that one tagging protocol will provide strictly
better performance than the other, just allow them to specify the
preference in the device tree.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a trivial typo when spelling "protocol", fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use dev_addr_set() instead of writing directly to netdev->dev_addr
in various misc and old drivers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: remove direct netdev->dev_addr writes

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

This series contains top 5 conversions in terms of LoC required
to bring the driver into compliance.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

8390 contains a lot of loops assigning netdev->dev_addr
byte by byte. Convert what's possible directly to
eth_hw_addr_set(), use local buf in other places.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consify temporary variables pointing to netdev->dev_addr.

A few places need local storage but pretty simple conversion
over all. Note that macaddr[] is an array of ints, so we need
to keep the loops.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consify the casts of netdev->dev_addr.

Convert pointless to eth_hw_addr_set() where possible.

Use local buffers in a number of places.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3 does various forms of direct writes to netdev->dev_addr.
Use a local buffer. Make sure local buffer is aligned since
eth_platform_get_mac_address() may call ether_addr_copy().

tg3_get_device_address() returns whenever it finds a method
that found a valid address. Instead of modifying all the exit
points pass the buffer from the outside and commit the address
in the caller.

Constify the argument of the set addr helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth writes to dev_addr byte by byte, make it use
a local buffer instead. Commit the changes with
eth_hw_addr_set() at the end.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>