SPI NOR core changes:
- Read back written SR value to make sure the write was done correctly.
- Introduce a common function for Read ID that manufacturer drivers can
  use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
  drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.

SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond flashes
  use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
  readability.
- Use the common Read ID function to verify switch to Octal DTR mode for
  Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and Cypress
  flashes since the operation is instant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Clock source is prepared and enabled by clk_prepare_enable()
in probe function, but not disabled or unprepared in remove
function.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220516092911.953066-1-yangyingliang@huawei.com

Extend fixed-partitions binding for support of Sercomm partition parser
(add "sercomm,sc-partitions" compatible).
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220516151725.885427-1-csharper2005@gmail.com

Add "sercomm" vendor prefix for "Sercomm (Suzhou) Corporation".

Company website:
Link: https://www.sercomm.com/Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220516151637.885324-1-csharper2005@gmail.com

Currently phram always uses ioremap(), but this is unnecessary when
normal memory is used.  If the reserved-memory node does not specify the
no-map property, indicating it should be mapped as system RAM and
ioremap() cannot be used on it, use a cached mapping using
memremap(MEMREMAP_WB) instead.

On one of my systems this improves read performance by ~70%.

(Note that this driver has always used normal memcpy/memset functions on
memory obtained from ioremap(), which sparse doesn't like.  There is no
memremap() variant which maps exactly to ioremap() on all architectures,
so that behaviour of the driver is not changed to avoid affecting
existing users, but the sparse warnings are suppressed in the moved code
with __force.)
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220510151822.1809278-1-vincent.whitchurch@axis.com

Until this change MTD subsystem supported handling partitions only with
MTD partitions parsers. That's a specific / limited API designed around
partitions.

Some MTD partitions may however require different handling. They may
contain specific data that needs to be parsed and somehow extracted. For
that purpose MTD subsystem should allow binding of standard platform
drivers.

An example can be U-Boot (sub)partition with environment variables.
There exist a "u-boot,env" DT binding for MTD (sub)partition that
requires an NVMEM driver.

Ref: 5db1c2db ("dt-bindings: nvmem: add U-Boot environment variables binding")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220510131259.555-1-zajec5@gmail.com

The intention was to print the JEDEC ID in the following format:
  nn nn nn

In this case format specifier has to be "%*ph". Fix it.

Fixes: 0257be79 ("mtd: spi-nor: expose internal parameters via debugfs")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220512112027.3771734-1-michael@walle.cc

This patch allows accessing the upper 16m on the A variant (EN25QH256A) of
the EN25QH256 that shares same JEDEC ID.

Without this patch, addr_with is detected to be '4' but the read_opcode is
a plain READ (supporting only 3 byte addresses).
Setting PARSE_SFDP is enough to detect the read_opcode READ_4B on the A
variant. READ_4B is not available on the no-A variant.

Both variants support 4-byte address mode (spi_nor_set_4byte_addr_mode)
but that is prone to breaking on unexpected reboots if the reset pin isn't
connected (broken-flash-reset).

The no-A variant supports a 'high bank latch mode' that affects read,
program, and erase commands - similar to the extended address register
(EAR).
The HBL bit is manipulated using the ENHBL (0x67) and EXHBL (0x98)
opcodes.

Should it become necessary to distinguish the two variants in the future,
the A variant sets the SNOR_HWCAPS_READ_1_1_4 SFDP param - the no-A
variant doesn't.

Tested with and without fast read on the A variant only.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220502233310.791565-2-leon@georgemail.eu

Add support for winbond W25Q512NW-IM chip.

Below are the tests done:

1. Verified flashing binary image on spi card using flashrom tool.
2. Verified OTP support, below are the test results:

 localhost / # cat
 /sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/spi16/
 spi16.0/spi-nor/jedec_id
 ef8020

 localhost / # cat
 /sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/spi16/
 spi16.0/spi-nor/manufacturer
 winbond

 localhost / # cat
 /sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/spi16/
 spi16.0/spi-nor/partname
 w25q512nwm

 localhost / # hexdump
 /sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/sp
 i16/spi16.0/spi-nor/sfdp
 0000000 4653 5044 0106 ff01 0600 1001 0080 ff00
 0000010 0084 0201 00d0 ff00 ffff ffff ffff ffff
 0000020 6800 6c65 6f6c 7720 726f 646c ffff ffff
 0000030 ffff ffff ffff ffff ffff ffff ffff ffff
 *
 0000080 20e5 fffb ffff 1fff eb44 6b08 3b08 bb42
 0000090 fffe ffff ffff 0000 ffff eb40 200c 520f
 00000a0 d810 0000 0233 00a6 e781 d914 63e9 3376
 00000b0 757a 757a bdf7 5cd5 f719 ff5d 70e9 a5f9
 00000c0 ffff ffff ffff ffff ffff ffff ffff ffff
 00000d0 0aff fff0 ff21 ffdc
 00000d8

 localhost / # md5sum
 /sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/spi
 16/spi16.0/spi-nor/sfdp
 106d89d6c049110bc94c01517cb4ce24
 /sys/bus/platform/devices/soc@0/88dc000.spi/
 spi_master/spi16/spi16.0/spi-nor/sfdp
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/1651234239-32217-1-git-send-email-quic_c_sbhanu@quicinc.com

There is no way to gather all information to verify support for a new
flash chip. Also if you want to convert an existing flash chip to the
new SFDP parsing, there is not enough information to determine if the
flash will work like before. To ease this development, expose internal
parameters via the debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-2-michael@walle.cc

The function will also be used by the debugfs module.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-1-michael@walle.cc

The "Extended Address Register" is winbond specific. If the flash is
larger than 16MiB and is used in 3 byte address mode, it is used to set
the remaining address bits. Move the write_ear() function, the opcode
macros and the spimem op template into the winbond module and rename
them accordingly.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429100153.2338501-1-michael@walle.cc

The rdsr dummy cycles are only used by the 8d-8d-8d mode. Mention that
in the documentation.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112837.2792242-1-michael@walle.cc

Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220323170458.5608-5-ikegami.t@gmail.com

It is for the model number 01, 02, V1 and V2.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220323170458.5608-4-ikegami.t@gmail.com

Since commit dfeae107("mtd: cfi_cmdset_0002: Change write buffer to
check correct value") buffered writes fail on S29GL064N. This is
because, on S29GL064N, reads return 0xFF at the end of DQ polling for
write completion, where as, chip_good() check expects actual data
written to the last location to be returned post DQ polling completion.
Fix is to revert to using chip_good() for S29GL064N which only checks
for DQ lines to settle down to determine write completion.

Link: https://lore.kernel.org/r/b687c259-6413-26c9-d4c9-b3afa69ea124@pengutronix.de/
Fixes: dfeae107("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Cc: stable@vger.kernel.org
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220323170458.5608-3-ikegami.t@gmail.com

This is a preparation patch for the S29GL064N buffer writes fix. There
is no functional change.

Link: https://lore.kernel.org/r/b687c259-6413-26c9-d4c9-b3afa69ea124@pengutronix.de/
Fixes: dfeae107("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220323170458.5608-2-ikegami.t@gmail.com

Writing volatile registers are instant according to Micron and do not
need any status polling. Remove status polling on volatile registers write.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-12-tudor.ambarus@microchip.com

Writing volatile registers are instant according to Cypress and do not
need any status polling. Remove status polling on volatile registers write.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-11-tudor.ambarus@microchip.com

Clean the op declaration and hide the details of each op. With this it
results a cleanner, easier to read code. No functional change expected.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220420103427.47867-10-tudor.ambarus@microchip.com

Introduce template operation to remove code duplication.
Split spi_nor_cypress_octal_dtr_enable() in
spi_nor_cypress_octal_dtr_ena() spi_nor_cypress_octal_dtr_dis() as it no
longer made sense to try to keep everything alltogether: too many
"if (enable)" throughout the code, which made the code difficult to read.
Add debug messages in case spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-9-tudor.ambarus@microchip.com

Introduce template operation to remove code duplication.
Split spi_nor_micron_octal_dtr_enable() in spi_nor_micron_octal_dtr_en()
and spi_nor_micron_octal_dtr_dis() as it no longer made sense to try to
keep everything alltogether: too many "if (enable)" throughout the code,
which made the code difficult to follow. Add dev_dbg messages in case
spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-8-tudor.ambarus@microchip.com

There are manufacturers that use registers indexed by address. Some of
them support "read/write any register" opcodes. Provide core methods that
can be used by all manufacturers. SPI NOR controller ops are intentionally
not supported as we intend to move all the SPI NOR controller drivers
under the SPI subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-7-tudor.ambarus@microchip.com

Use spi_nor_read_id() core method to avoid duplication of code. Now the ID
is read on the full SPI_NOR_MAX_ID_LEN instead of
round_up(nor->info->id_len, 2), but it doesn't harm to read more ID bytes,
so the change comes with no secondary effects. dev_dbg messages in case
spi_nor_read_id() fails, will be added in a further patch after we split
the octal DTR enable/disable methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-6-tudor.ambarus@microchip.com

RDID is used in the core to auto detect the flash, but also by some
manufacturer drivers that contain flashes that support Octal DTR mode,
so that they can read the flash ID after the switch to Octal DTR was made
to test if the switch was successful. Introduce a core method for RDID op
to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-5-tudor.ambarus@microchip.com

In case spi_nor_match_name() returned NULL, the auto detection was
issued twice. There's no reason to try to detect the same chip twice,
do the auto detection only once.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-4-tudor.ambarus@microchip.com

Similar to spi_nor_match_name() extend the search of flash_info through
all the manufacturers, this time doing the match by ID. There's no reason
to limit the search per manufacturer yet, do it globally, search the flash
in all the parts of all manufacturers in a single method.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-3-tudor.ambarus@microchip.com

The method is matching a flash_info entry by searching by name. Rename
the method for better clarity.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-2-tudor.ambarus@microchip.com

Read back Status Register 1 to ensure that the written byte match the
received value and return -EIO if read back test failed.

Without this patch, spi_nor_write_16bit_sr_and_check() only check the
second half of the 16bit. It causes errors like spi_nor_sr_unlock()
return success incorrectly when spi_nor_write_16bit_sr_and_check()
doesn't write SR successfully.

Fixes: 39d1e334 ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126073227.3401275-1-chentsung@chromium.org

On some systems, the oops only has relative time from boot.
Signed-off-by: Jean-Marc Eurin <jmeurin@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220425160927.3823016-1-jmeurin@google.com

Create a dump header to enable the addition of fields without having
to modify the rest of the code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jean-Marc Eurin <jmeurin@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220421234244.2172003-3-jmeurin@google.com

The read buffer size depends on the MTDOOPS_HEADER_SIZE.

Tested: Changed the header size, it doesn't panic, header is still
read/written correctly.
Signed-off-by: Jean-Marc Eurin <jmeurin@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220421234244.2172003-2-jmeurin@google.com

Warning on every translated mtd partition results in excessive log noise
if this driver is loaded:

  nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
  nand: Macronix MX30LF1G18AC
  nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
  mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
  read_bbt: found bbt at block 1023
  10 fixed-partitions partitions found on MTD device mt7621-nand
  Creating 10 MTD partitions on "mt7621-nand":
  0x000000000000-0x000000080000 : "Bootloader"
  mtdblock: MTD device 'Bootloader' is NAND, please consider using UBI block devices instead.
  0x000000080000-0x000000100000 : "Config"
  mtdblock: MTD device 'Config' is NAND, please consider using UBI block devices instead.
  0x000000100000-0x000000140000 : "Factory"
  mtdblock: MTD device 'Factory' is NAND, please consider using UBI block devices instead.
  0x000000140000-0x000002000000 : "Kernel"
  mtdblock: MTD device 'Kernel' is NAND, please consider using UBI block devices instead.
  0x000000540000-0x000002000000 : "ubi"
  mtdblock: MTD device 'ubi' is NAND, please consider using UBI block devices instead.
  0x000002140000-0x000004000000 : "Kernel2"
  mtdblock: MTD device 'Kernel2' is NAND, please consider using UBI block devices instead.
  0x000004000000-0x000004100000 : "wwan"
  mtdblock: MTD device 'wwan' is NAND, please consider using UBI block devices instead.
  0x000004100000-0x000005100000 : "data"
  mtdblock: MTD device 'data' is NAND, please consider using UBI block devices instead.
  0x000005100000-0x000005200000 : "rom-d"
  mtdblock: MTD device 'rom-d' is NAND, please consider using UBI block devices instead.
  0x000005200000-0x000005280000 : "reserve"
  mtdblock: MTD device 'reserve' is NAND, please consider using UBI block devices instead.
  mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21

This is more likely to annoy than to help users of embedded distros where
this driver is enabled by default.  Making the blockdevs available does
not imply that they are in use, and warning about bootloader partitions
or other devices which obviously never will be mounted is more confusing
than helpful.

Move the warning to open(), where it will be of more use - actually warning
anyone who mounts a file system on NAND using mtdblock.

Fixes: e07403a8 ("mtdblock: Warn if added for a NAND device")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220328161108.87757-1-bjorn@mork.no

Allow phram to be probed from the devicetree.  It expects to be in a
reserved-memory node as documented by the bindings.  This allows things
like partitioning to be specified via the devicetree.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412135302.1682890-4-vincent.whitchurch@axis.com

Add bindings to allow MTD/block devices to be used in reserved-memory
regions using the "phram" (MTD in PHysical RAM) driver.

This allows things like partitioning to be specified via the existing
devicetree bindings.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412135302.1682890-3-vincent.whitchurch@axis.com

Allow the MTD index to be specified via a devicetree alias, so that the
number does not just depend on probe order.  This is useful to allow
pseudo-devices like phram to be optionally used on systems, without
having this affect the numbering of the real hardware MTD devices.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412135302.1682890-2-vincent.whitchurch@axis.com

After conversion the jedec,spi-nor DT schema to reference other schemas
(SPI and MTD) and use unevaluatedProperties, few properties are
redundant.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220408063720.12826-1-krzysztof.kozlowski@linaro.org

This custom maps driver was never used with the device tree
enabled IXP4xx systems, which use the physmap add-on from
commit 2aba2f2a
("mtd: physmap_of: add a hook for Intel IXP4xx flash probing")

Since kernel v5.18-rc1 IXP4xx is only booting from the device
tree so drop this old driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220407210844.2489682-1-linus.walleij@linaro.org

Pull xen fixlet from Juergen Gross:
 "A single cleanup patch for the Xen balloon driver"

* tag 'for-linus-5.18-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: don't use PV mode extra memory for zone device allocations