- 09 Sep, 2005 40 commits
-
-
Patrick Boettcher authored
Add USB IDs of the Kworld Xpert DVB-T USB2.0 (clone of the ADStech box). Thanks to Marcus Hagn for testing. Signed-off-by:
Patrick Boettcher <pb@linuxtv.org> Signed-off-by:
Johannes Stezenbach <js@linuxtv.org> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Patrick Boettcher authored
Add driver for the TwinhanDTV StarBox and clones. Thanks to Ralph Metzler for his initial work on this box and thanks to Twinhan for their support. Signed-off-by:
-
Mac Michaels authored
This fix has also been applied to lgdt330x. There is an optimization that keeps track of the frequency tuned by the digital decoder. The digital driver does not set the frequency if it has not changed since it was tuned. The analog tuner driver knows nothing about the frequency saved by the digital driver. When the frequency is set using the video4linux code with tvtime, the hardware get changed but the digital driver's state does not get updated. Switch back to the same digital channel and the driver finds no change in frequency so the tuner is not reset to the digital frequency. The work around is to remove the check and always set the tuner to the specified frequency. Signed-off-by:
Mac Michaels <wmichaels1@earthlink.net> Signed-off-by:
Michael Krufky <mkrufky@m1k.net> Signed-off-by:
-
Patrick Boettcher authored
while investigating the QAM_128-issue with the stv0297-driver for the Cablestar (which is not the same as the one in dvb-kernel CVS, yet), I fixed it, not by increasing the timeout, but by disabling the corner-detection for QAM_128 and higher. This patch has been tested on dvb-kernel cvs, and has been reported to work by multiple users. Some cards still need timeout increase on top of this patch. This will be addressed later. Signed-off-by:
-
Johannes Stezenbach authored
Clean up timeout handling. Signed-off-by:
-
Adam Szalkowski authored
Fix DiSEqC problems. Signed-off-by:
Adam Szalkowski <adam@szalkowski.de> Signed-off-by:
-
Johannes Stezenbach authored
Fix DiSEqC switching (one bug fix suggested by Peter Hettkamp, and one experimentally determined msleep(30) suggested by Adam Szalkowski). Signed-off-by:
-
Johannes Stezenbach authored
Reset acgconf register after tuning to improve locking, as suggested by Marco Schluessler. Minor cleanups in ves1820_init(). Signed-off-by:
-
Andrew de Quincey authored
Fix SNR reading Signed-off-by:
Andrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by:
-
Andrew de Quincey authored
Allow the stv0299 to read the BER and UCBLOCKS. Signed-off-by:
-
Andrew de Quincey authored
Misc. fixes. Signed-off-by:
-
Andreas Oberritter authored
Pass a pointer to the i2c bus to the pll callbacks (stv0299 only). It was not possible to tell which i2c bus should be used if an adapter has multiple frontends on multiple i2c buses. Signed-off-by:
Andreas Oberritter <obi@linuxtv.org> Signed-off-by:
-
Barry Scott authored
Fix two problems with the signal strength value in the mt352.c frontend: 1. the 4 most significant bits are zeroed - shift and mask wrong way round 2. need to align the 12 bits from the registers at the top of the 16 bit returned value - otherwise the range is not 0 to 0xffff its 0xf000 to 0xffff Signed-off-by:
Barry Scott <barry.scott@onelan.co.uk> Signed-off-by:
-
Dominique Dumont authored
Patch from Dominique Dumont to get the SCM Red Viaccess CAM working with the budget-ci. Signed-off-by:
Dominique Dumont <domi.dumont@free.fr> Signed-off-by:
-
Andreas Oberritter authored
Formatting fixes (Lindent + some handwork). Signed-off-by:
-
Andreas Oberritter authored
Use INIT_LIST_HEAD for frontend_list. Signed-off-by:
-
Andreas Oberritter authored
Removed more unused variables and constants. Signed-off-by:
-
Andreas Oberritter authored
Removed unused descramble_mac_address and descramble_section_payload callbacks. Signed-off-by:
-
Andreas Oberritter authored
Removed some useless functions and variables. Signed-off-by:
-
Andreas Oberritter authored
Don't return immediately from dvb_dmx_swfilter_section_packet() if CC is not ok. Otherwise a new feed drops all packets until the first packet with CC=0 arrives. Signed-off-by:
-
Andreas Oberritter authored
Glue code for DMX_GET_CAPS and DMX_SET_SOURCE ioctls. Signed-off-by:
-
Johannes Stezenbach authored
Don't build empty built-in.o when DVB/V4L is not configured. Thanks to Sam Ravnborg and Keith Owens. Signed-off-by:
-
Olaf Hering authored
Remove all #include <linux/version.h> and all references to LINUX_VERSION_CODE and KERNEL_VERSION. Based on patch by Olaf Hering. Signed-off-by:
Olaf Hering <olh@suse.de> Signed-off-by:
-
Johannes Stezenbach authored
Update email address of Peter Hettkamp. Signed-off-by:
-
Truxton Fulton authored
I have a system (Biostar IDEQ210M mini-pc with a VIA chipset) which will not reboot unless a keyboard is plugged in to it. I have tried all combinations of the kernel "reboot=x,y" flags to no avail. Rebooting by any method will leave the system in a wedged state (at the "Restarting system" message). I finally tracked the problem down to the machine's refusal to fully reboot unless the keyboard controller status register had bit 2 set. This is the "System flag" which when set, indicates successful completion of the keyboard controller self-test (Basic Assurance Test, BAT). I suppose that something is trying to protect against sporadic reboots unless the keyboard controller is in a good state (a keyboard is present), but I need this machine to be headless. I found that setting the system flag (via the command byte) before giving the "pulse reset line" command will allow the reboot to proceed. The patch is simple, and I think it should be fine for everybody whether they have this type of machine or not. This affects the "hard" reboot (as done when the kernel boot flags "reboot=c,h" are used). Signed-off-by:
-
Paul Fulghum authored
Fix async internal loopback by not using enable_loopback function which reprograms clocking and should only be used for hdlc mode. Signed-off-by:
Paul Fulghum <paulkf@microgate.com> Signed-off-by:
-
Paul Fulghum authored
Add ability to clear statistics. Signed-off-by:
-
Paul Fulghum authored
Disable burst transfers on adapter local bus. Hardware feature does not work on latest version of adapter. Signed-off-by:
-
Paul Fulghum authored
Serial signals were incorrectly mapped twice to events. Signed-off-by:
-
Paul Fulghum authored
Add internal loopback support for asynchronous mode operation. Signed-off-by:
-
Paul Fulghum authored
Add the ability to clear statistics. Signed-off-by:
-
Paul Fulghum authored
Make some fields of DMA descriptor volatile to prevent compiler optimizations. Signed-off-by:
-
Andrew Morton authored
That ?: trick gives us the creeps. Cc: Jens Axboe <axboe@suse.de> Signed-off-by:
-
Kenji Kaneshige authored
The function prototype for handle_IRQ_event() in a few architctures is not needed because they use GENERIC_HARDIRQ. Signed-off-by:
Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by:
-
KUROSAWA Takahiro authored
This patch fixes minor problem that the CPUSETS have when files in the cpuset filesystem are read after lseek()-ed beyond the EOF. Signed-off-by:
KUROSAWA Takahiro <kurosawa@valinux.co.jp> Acked-by:
Paul Jackson <pj@sgi.com> Signed-off-by:
-
Benjamin LaHaise authored
Implement a per-kiocb lock to serialise retry operations and cancel. This is done using wait_on_bit_lock() on the KIF_LOCKED bit of kiocb->ki_flags. Also, make the cancellation path lock the kiocb and subsequently release all references to it if the cancel was successful. This version includes a fix for the deadlock with __aio_run_iocbs. Signed-off-by:
Benjamin LaHaise <bcrl@linux.intel.com> Signed-off-by:
-
Wendy Cheng authored
Note that other than few exceptions, most of the current filesystem and/or drivers do not have aio cancel specifically defined (kiob->ki_cancel field is mostly NULL). However, sys_io_cancel system call universally sets return code to -EAGAIN. This gives applications a wrong impression that this call is implemented but just never works. We have customer inquires about this issue. Changed by Benjamin LaHaise to EINVAL instead of ENOSYS Signed-off-by:
S. Wendy Cheng <wcheng@redhat.com> Acked-by:
Benjamin LaHaise <bcrl@kvack.org> Signed-off-by:
-
Deepak Saxena authored
Signed-off-by:
Deepak Saxena <dsaxena@plexity.net> Cc: Matt Mackall <mpm@selenic.com> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by:
-
Andrew Stribblehill authored
* Makes BFS code endianness-clean. * Fixes some signedness warnings. * Fixes a problem in fs/bfs/inode.c:164 where inodes not synced to disk don't get fully marked as clean. Here's how to reproduce it: # mount -o loop -t bfs /bfs.img /mnt # df -i /mnt Filesystem Inodes IUsed IFree IUse% Mounted on /bfs.img 48 1 47 3% /mnt # df -k /mnt Filesystem 1K-blocks Used Available Use% Mounted on /bfs.img 512 5 508 1% /mnt # cp 60k-archive.zip /mnt/mt.zip # df -k /mnt Filesystem 1K-blocks Used Available Use% Mounted on /bfs.img 512 65 447 13% /mnt # df -i /mnt Filesystem Inodes IUsed IFree IUse% Mounted on /bfs.img 48 2 46 5% /mnt # rm /mnt/mt.zip # echo $? 0 [If the unlink happens before the buffers flush, the following happens:] # df -i /mnt Filesystem Inodes IUsed IFree IUse% Mounted on /bfs.img 48 2 46 5% /mnt # df -k /mnt Filesystem 1K-blocks Used Available Use% Mounted on /bfs.img 512 65 447 13% /mnt fs/bfs/bfs.h | 1 Signed-off-by:
Andrew Stribblehill <ads@wompom.org> Cc: <tigran@veritas.com> Signed-off-by:
-
Chen, Kenneth W authored
For architecture like ia64, the switch stack structure is fairly large (currently 528 bytes). For context switch intensive application, we found that significant amount of cache misses occurs in switch_to() function. The following patch adds a hook in the schedule() function to prefetch switch stack structure as soon as 'next' task is determined. This allows maximum overlap in prefetch cache lines for that structure. Signed-off-by:
Ken Chen <kenneth.w.chen@intel.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by:
-
