[PROBLEM]

Unlike data/metadata corruption, if scrub detected some error in the
super block, the only error message is from the updated device status:

  BTRFS info (device dm-1): scrub: started on devid 2
  BTRFS error (device dm-1): bdev /dev/mapper/test-scratch2 errs: wr 0, rd 0, flush 0, corrupt 1, gen 0
  BTRFS info (device dm-1): scrub: finished on devid 2 with status: 0

This is not helpful at all.

[CAUSE]
Unlike data/metadata error reporting, there is no visible report in
kernel dmesg to report supper block errors.

In fact, return value of scrub_checksum_super() is intentionally
skipped, thus scrub_handle_errored_block() will never be called for
super blocks.

[FIX]
Make super block errors to output an error message, now the full
dmesg would looks like this:

  BTRFS info (device dm-1): scrub: started on devid 2
  BTRFS warning (device dm-1): super block error on device /dev/mapper/test-scratch2, physical 67108864
  BTRFS error (device dm-1): bdev /dev/mapper/test-scratch2 errs: wr 0, rd 0, flush 0, corrupt 1, gen 0
  BTRFS info (device dm-1): scrub: finished on devid 2 with status: 0
  BTRFS info (device dm-1): scrub: started on devid 2

This fix involves:

- Move the super_errors reporting to scrub_handle_errored_block()
  This allows the device status message to show after the super block
  error message.
  But now we no longer distinguish super block corruption and generation
  mismatch, now all counted as corruption.

- Properly check the return value from scrub_checksum_super()
- Add extra super block error reporting for scrub_print_warning().
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

With CONFIG_READ_ONLY_THP_FOR_FS, the Linux kernel supports using THPs for
read-only mmapped files, such as shared libraries. However, the kernel
makes no attempt to actually align those mappings on 2MB boundaries,
which makes it impossible to use those THPs most of the time. This issue
applies to general file mapping THP as well as existing setups using
CONFIG_READ_ONLY_THP_FOR_FS. This is easily fixed by using
thp_get_unmapped_area for the unmapped_area function in btrfs, which
is what ext2, ext4, fuse, and xfs all use.

Initially btrfs had been left out in commit 8c07fc452ac0 ("btrfs: fix
alignment of VMA for memory mapped files on THP") as btrfs does not support
DAX. However, commit 1854bc6e ("mm/readahead: Align file mappings
for non-DAX") removed the DAX requirement. We should now be able to call
thp_get_unmapped_area() for btrfs.

The problem can be seen in /proc/PID/smaps where THPeligible is set to 0
on mappings to eligible shared object files as shown below.

Before this patch:

  7fc6a7e18000-7fc6a80cc000 r-xp 00000000 00:1e 199856
  /usr/lib64/libcrypto.so.1.1.1k
  Size:               2768 kB
  THPeligible:    0
  VmFlags: rd ex mr mw me

With this patch the library is mapped at a 2MB aligned address:

  fbdfe200000-7fbdfe4b4000 r-xp 00000000 00:1e 199856
  /usr/lib64/libcrypto.so.1.1.1k
  Size:               2768 kB
  THPeligible:    1
  VmFlags: rd ex mr mw me

This fixes the alignment of VMAs for any mmap of a file that has the
rd and ex permissions and size >= 2MB. The VMA alignment and
THPeligible field for anonymous memory is handled separately and
is thus not effected by this change.

CC: stable@vger.kernel.org # 5.18+
Signed-off-by: Alexander Zhu <alexlzhu@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

This wait event is very similar to the pending ordered wait event in the
sense that it occurs in a different context than the condition signaling
for the event. The signaling occurs in btrfs_remove_ordered_extent()
while the wait event is implemented in btrfs_start_ordered_extent() in
fs/btrfs/ordered-data.c

However, in this case a thread must not acquire the lockdep map for the
ordered extents wait event when the ordered extent is related to a free
space inode. That is because lockdep creates dependencies between locks
acquired both in execution paths related to normal inodes and paths
related to free space inodes, thus leading to false positives.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ioannis Angelakopoulos <iangelak@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Reinitialize the class of the lockdep map for struct inode's
mapping->invalidate_lock in load_free_space_cache() function in
fs/btrfs/free-space-cache.c. This will prevent lockdep from producing
false positives related to execution paths that make use of free space
inodes and paths that make use of normal inodes.

Specifically, with this change lockdep will create separate lock
dependencies that include the invalidate_lock, in the case that free
space inodes are used and in the case that normal inodes are used.

The lockdep class for this lock was first initialized in
inode_init_always() in fs/inode.c.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ioannis Angelakopoulos <iangelak@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>

In contrast to the num_writers and num_extwriters wait events, the
condition for the pending ordered wait event is signaled in a different
context from the wait event itself. The condition signaling occurs in
btrfs_remove_ordered_extent() in fs/btrfs/ordered-data.c while the wait
event is implemented in btrfs_commit_transaction() in
fs/btrfs/transaction.c

Thus the thread signaling the condition has to acquire the lockdep map
as a reader at the start of btrfs_remove_ordered_extent() and release it
after it has signaled the condition. In this case some dependencies
might be left out due to the placement of the annotation, but it is
better than no annotation at all.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ioannis Angelakopoulos <iangelak@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Add lockdep annotations for the transaction states that have wait
events;

  1) TRANS_STATE_COMMIT_START
  2) TRANS_STATE_UNBLOCKED
  3) TRANS_STATE_SUPER_COMMITTED
  4) TRANS_STATE_COMPLETED

The new macros introduced here to annotate the transaction states wait
events have the same effect as the generic lockdep annotation macros.

With the exception of the lockdep annotation for TRANS_STATE_COMMIT_START
the transaction thread has to acquire the lockdep maps for the
transaction states as reader after the lockdep map for num_writers is
released so that lockdep does not complain.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ioannis Angelakopoulos <iangelak@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Similarly to the num_writers wait event in fs/btrfs/transaction.c add a
lockdep annotation for the num_extwriters wait event.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ioannis Angelakopoulos <iangelak@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Annotate the num_writers wait event in fs/btrfs/transaction.c with
lockdep in order to catch deadlocks involving this wait event.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ioannis Angelakopoulos <iangelak@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Introduce four macros that are used to annotate wait events in btrfs code
with lockdep;

  1) the btrfs_lockdep_init_map
  2) the btrfs_lockdep_acquire,
  3) the btrfs_lockdep_release
  4) the btrfs_might_wait_for_event macros.

The btrfs_lockdep_init_map macro is used to initialize a lockdep map.

The btrfs_lockdep_<acquire,release> macros are used by threads to take
the lockdep map as readers (shared lock) and release it, respectively.

The btrfs_might_wait_for_event macro is used by threads to take the
lockdep map as writers (exclusive lock) and release it.

In general, the lockdep annotation for wait events work as follows:

The condition for a wait event can be modified and signaled at the same
time by multiple threads. These threads hold the lockdep map as readers
when they enter a context in which blocking would prevent signaling the
condition. Frequently, this occurs when a thread violates a condition
(lockdep map acquire), before restoring it and signaling it at a later
point (lockdep map release).

The threads that block on the wait event take the lockdep map as writers
(exclusive lock). These threads have to block until all the threads that
hold the lockdep map as readers signal the condition for the wait event
and release the lockdep map.

The lockdep annotation is used to warn about potential deadlock scenarios
that involve the threads that modify and signal the wait event condition
and threads that block on the wait event. A simple example is illustrated
below:

Without lockdep:

TA                                        TB
cond = false
                                          lock(A)
                                          wait_event(w, cond)
                                          unlock(A)
lock(A)
cond = true
signal(w)
unlock(A)

With lockdep:

TA                                        TB
rwsem_acquire_read(lockdep_map)
cond = false
                                          lock(A)
                                          rwsem_acquire(lockdep_map)
                                          rwsem_release(lockdep_map)
                                          wait_event(w, cond)
                                          unlock(A)
lock(A)
cond = true
signal(w)
unlock(A)
rwsem_release(lockdep_map)

In the second case, with the lockdep annotation, lockdep would warn about
an ABBA deadlock, while the first case would just deadlock at some point.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ioannis Angelakopoulos <iangelak@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

There is an internal report on hitting the following ASSERT() in
recalculate_thresholds():

 	ASSERT(ctl->total_bitmaps <= max_bitmaps);

Above @max_bitmaps is calculated using the following variables:

- bytes_per_bg
  8 * 4096 * 4096 (128M) for x86_64/x86.

- block_group->length
  The length of the block group.

@max_bitmaps is the rounded up value of block_group->length / 128M.

Normally one free space cache should not have more bitmaps than above
value, but when it happens the ASSERT() can be triggered if
CONFIG_BTRFS_ASSERT is also enabled.

But the ASSERT() itself won't provide enough info to know which is going
wrong.
Is the bg too small thus it only allows one bitmap?
Or is there something else wrong?

So although I haven't found extra reports or crash dump to do further
investigation, add the extra info to make it more helpful to debug.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Pull ext4 fixes from Ted Ts'o:
 "Regression and bug fixes:

   - Performance regression fix from 5.18 on a Rasberry Pi

   - Fix extent parsing bug which triggers a BUG_ON when a (corrupted)
     extent tree has has a non-root node when zero entries.

   - Fix a livelock where in the right (wrong) circumstances a large
     number of nfsd threads can try to write to a nearly full file
     system, and retry for hours(!)"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: limit the number of retries after discarding preallocations blocks
  ext4: fix bug in extents parsing when eh_entries == 0 and eh_depth > 0
  ext4: use buckets for cr 1 block scan instead of rbtree
  ext4: use locality group preallocation for small closed files
  ext4: make directory inode spreading reflect flexbg size
  ext4: avoid unnecessary spreading of allocations among groups
  ext4: make mballoc try target group first even with mb_optimize_scan

Merge tag 'dax-and-nvdimm-fixes-v6.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm

Pull NVDIMM and DAX fixes from Dan Williams:
 "A recently discovered one-line fix for devdax that further addresses a
  v5.5 regression, and (a bit embarrassing) a small batch of fixes that
  have been sitting in my fixes tree for weeks.

  The older fixes have soaked in linux-next during that time and address
  an fsdax infinite loop and some other minor fixups.

   - Fix a infinite loop bug in fsdax

   - Fix memory-type detection for devdax (EINJ regression)

   - Small cleanups"

* tag 'dax-and-nvdimm-fixes-v6.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  devdax: Fix soft-reservation memory description
  fsdax: Fix infinite loop in dax_iomap_rw()
  nvdimm/namespace: drop nested variable in create_namespace_pmem()
  ndtest: Cleanup all of blk namespace specific code
  pmem: fix a name collision

Pull i2c fixes from Wolfram Sang:
 "I2C driver bugfixes for mlxbf and imx, a few documentation fixes after
  the rework this cycle, and one hardening for the i2c-mux core"

* tag 'i2c-for-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mux: harden i2c_mux_alloc() against integer overflows
  i2c: mlxbf: Fix frequency calculation
  i2c: mlxbf: prevent stack overflow in mlxbf_i2c_smbus_start_transaction()
  i2c: mlxbf: incorrect base address passed during io write
  Documentation: i2c: fix references to other documents
  MAINTAINERS: remove Nehal Shah from AMD MP2 I2C DRIVER
  i2c: imx: If pm_runtime_get_sync() returned 1 device access is possible

Pick up another "Soft Reservation" fix for v6.0-final on top of some
straggling nvdimm fixes that missed v5.19.

The "hmem" platform-devices that are created to represent the
platform-advertised "Soft Reserved" memory ranges end up inserting a
resource that causes the iomem_resource tree to look like this:

340000000-43fffffff : hmem.0
  340000000-43fffffff : Soft Reserved
    340000000-43fffffff : dax0.0

This is because insert_resource() reparents ranges when they completely
intersect an existing range.

This matters because code that uses region_intersects() to scan for a
given IORES_DESC will only check that top-level 'hmem.0' resource and
not the 'Soft Reserved' descendant.

So, to support EINJ (via einj_error_inject()) to inject errors into
memory hosted by a dax-device, be sure to describe the memory as
IORES_DESC_SOFT_RESERVED. This is a follow-on to:

commit b13a3e5f ("ACPI: APEI: Fix _EINJ vs EFI_MEMORY_SP")

...that fixed EINJ support for "Soft Reserved" ranges in the first
instance.

Fixes: 262b45ae ("x86/efi: EFI soft reservation to E820 enumeration")
Reported-by: Ricardo Sandoval Torres <ricardo.sandoval.torres@intel.com>
Tested-by: Ricardo Sandoval Torres <ricardo.sandoval.torres@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Omar Avelar <omar.avelar@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mark Gross <markgross@kernel.org>
Link: https://lore.kernel.org/r/166397075670.389916.7435722208896316387.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Merge tag 'kbuild-fixes-v6.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix build error for the combination of SYSTEM_TRUSTED_KEYRING=y and
   X509_CERTIFICATE_PARSER=m

 - Fix DEBUG_INFO_SPLIT to generate debug info for GCC 11+ and Clang 12+

 - Revive debug info for assembly files

 - Remove unused code

* tag 'kbuild-fixes-v6.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  Makefile.debug: re-enable debug info for .S files
  Makefile.debug: set -g unconditional on CONFIG_DEBUG_INFO_SPLIT
  certs: make system keyring depend on built-in x509 parser
  Kconfig: remove unused function 'menu_get_root_menu'
  scripts/clang-tools: remove unused module

Pull s390 fix from Vasily Gorbik:

 - Fix potential hangs in VFIO AP driver

* tag 's390-6.0-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/vfio-ap: bypass unnecessary processing of AP resources

Pull power management fixes from Rafael Wysocki:
 "These fix an uninitialized variable usage in the operating performance
  points code and add missing DT bindings for it.

  Specifics:

   - Fix uninitialized variable usage in dev_pm_opp_config_clks_simple()
     (Christophe JAILLET)

   - Add missing OPP DT properties (Rob Herring)"

* tag 'pm-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  dt-bindings: opp: Add missing (unevaluated|additional)Properties on child nodes
  OPP: Fix an un-initialized variable usage

Pull char/misc driver fixes from Greg KH:
 "Here are three tiny driver fixes for 6.0-rc7.  They include:

   - phy driver reset bugfix

   - fpga memleak bugfix

   - counter irq config bugfix

  The first two have been in linux-next for a while, the last one has
  only been added to my tree in the past few days, but was in linux-next
  under a different commit id. I couldn't pull directly from the counter
  tree due to some gpg key propagation issue, so I took the commit
  directly from email instead"

* tag 'char-misc-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  counter: 104-quad-8: Fix skipped IRQ lines during events configuration
  fpga: m10bmc-sec: Fix possible memory leak of flash_buf
  phy: marvell: phy-mvebu-a3700-comphy: Remove broken reset support

Pull tty/serial driver fixes from Greg KH:
 "Here are some small, and late, serial driver fixes for 6.0-rc7 to
  resolve some reported problems.

  Included in here are:

   - tegra icount accounting fixes, including a framework function that
     other drivers will be converted over to using in 6.1-rc1.

   - fsl_lpuart reset bugfix

   - 8250 omap 485 bugfix

   - sifive serial clock bugfix

  The last three patches have not shown up in linux-next due to them
  being added to my tree only 2 days ago, but they are tiny and
  self-contained and the developers say they resolve issues that they
  have with 6.0-rc. The other three have been in linux-next for a while
  with no reported issues"

* tag 'tty-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: sifive: enable clocks for UART when probed
  serial: 8250: omap: Use serial8250_em485_supported
  serial: fsl_lpuart: Reset prior to registration
  serial: tegra-tcu: Use uart_xmit_advance(), fixes icount.tx accounting
  serial: tegra: Use uart_xmit_advance(), fixes icount.tx accounting
  serial: Create uart_xmit_advance()

Pull cgroup fixes from Tejun Heo:

 - Add Waiman Long as a cpuset maintainer

 - cgroup_get_from_id() could be fed a kernfs ID which doesn't point to
   a cgroup directory but a knob file and then crash. Error out if the
   lookup kernfs_node isn't a directory.

* tag 'cgroup-for-6.0-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: cgroup_get_from_id() must check the looked-up kn is a directory
  cpuset: Add Waiman Long as a cpuset maintainer

Pull workqueue fix from Tejun Heo:
 "Just one patch to improve flush lockdep coverage"

* tag 'wq-for-6.0-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: don't skip lockdep work dependency in cancel_work_sync()

Pull io_uring fix from Jens Axboe:
 "Just a single fix for an issue with un-reaped IOPOLL requests on ring
  exit"

* tag 'io_uring-6.0-2022-09-23' of git://git.kernel.dk/linux:
  io_uring: ensure that cached task references are always put on exit

Pull block fixes from Jens Axboe:
 "Fix a regression that's been plaguing us by reverting the offending
  commit, as attempts to both reproduce the issue and fix it in a saner
  fashion have failed.

  Fix for a potential oops condition in the s390 dasd block driver"

* tag 'block-6.0-2022-09-22' of git://git.kernel.dk/linux:
  Revert "block: freeze the queue earlier in del_gendisk"
  s390/dasd: fix Oops in dasd_alias_get_start_dev due to missing pavgroup

Alexey reported that the fraction of unknown filename instances in
kallsyms grew from ~0.3% to ~10% recently; Bill and Greg tracked it down
to assembler defined symbols, which regressed as a result of:

commit b8a90923 ("Kbuild: do not emit debug info for assembly with LLVM_IAS=1")

In that commit, I allude to restoring debug info for assembler defined
symbols in a follow up patch, but it seems I forgot to do so in

commit a66049e2 ("Kbuild: make DWARF version a choice")

Link: https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;h=31bf18645d98b4d3d7357353be840e320649a67d
Fixes: b8a90923 ("Kbuild: do not emit debug info for assembly with LLVM_IAS=1")
Reported-by: Alexey Alexandrov <aalexand@google.com>
Reported-by: Bill Wendling <morbo@google.com>
Reported-by: Greg Thelen <gthelen@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Dmitrii, Fangrui, and Mashahiro note:

  Before GCC 11 and Clang 12 -gsplit-dwarf implicitly uses -g2.

Fix CONFIG_DEBUG_INFO_SPLIT for gcc-11+ & clang-12+ which now need -g
specified in order for -gsplit-dwarf to work at all.

-gsplit-dwarf has been mutually exclusive with -g since support for
CONFIG_DEBUG_INFO_SPLIT was introduced in
commit 866ced95 ("kbuild: Support split debug info v4")
I don't think it ever needed to be.

Link: https://lore.kernel.org/lkml/20220815013317.26121-1-dmitrii.bundin.a@gmail.com/
Link: https://lore.kernel.org/lkml/CAK7LNARPAmsJD5XKAw7m_X2g7Fi-CAAsWDQiP7+ANBjkg7R7ng@mail.gmail.com/
Link: https://reviews.llvm.org/D80391
Cc: Andi Kleen <ak@linux.intel.com>
Reported-by: Dmitrii Bundin <dmitrii.bundin.a@gmail.com>
Reported-by: Fangrui Song <maskray@google.com>
Reported-by: Masahiro Yamada <masahiroy@kernel.org>
Suggested-by: Dmitrii Bundin <dmitrii.bundin.a@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

io_uring caches task references to avoid doing atomics for each of them
per request. If a request is put from the same task that allocated it,
then we can maintain a per-ctx cache of them. This obviously relies
on io_uring always pruning caches in a reliable way, and there's
currently a case off io_uring fd release where we can miss that.

One example is a ring setup with IOPOLL, which relies on the task
polling for completions, which will free them. However, if such a task
submits a request and then exits or closes the ring without reaping
the completion, then ring release will reap and put. If release happens
from that very same task, the completed request task refs will get
put back into the cache pool. This is problematic, as we're now beyond
the point of pruning caches.

Manually drop these caches after doing an IOPOLL reap. This releases
references from the current task, which is enough. If another task
happens to be doing the release, then the caching will not be
triggered and there's no issue.

Cc: stable@vger.kernel.org
Fixes: e98e49b2 ("io_uring: extend task put optimisations")
Reported-by: Homin Rhee <hominlab@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull arm64 fixes from Will Deacon:
 "These are all very simple and self-contained, although the CFI
  jump-table fix touches the generic linker script as that's where the
  problematic macro lives.

   - Fix false positive "sleeping while atomic" warning resulting from
     the kPTI rework taking a mutex too early.

   - Fix possible overflow in AMU frequency calculation

   - Fix incorrect shift in CMN PMU driver which causes problems with
     newer versions of the IP

   - Reduce alignment of the CFI jump table to avoid huge kernel images
     and link errors with !4KiB page size configurations"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  vmlinux.lds.h: CFI: Reduce alignment of jump-table to function alignment
  perf/arm-cmn: Add more bits to child node address offset field
  arm64: topology: fix possible overflow in amu_fie_setup()
  arm64: mm: don't acquire mutex when rewriting swapper

Commit e9088629 ("certs: make system keyring depend on x509 parser")
is not the right fix because x509_load_certificate_list() can be modular.

The combination of CONFIG_SYSTEM_TRUSTED_KEYRING=y and
CONFIG_X509_CERTIFICATE_PARSER=m still results in the following error:

    LD      .tmp_vmlinux.kallsyms1
  ld: certs/system_keyring.o: in function `load_system_certificate_list':
  system_keyring.c:(.init.text+0x8c): undefined reference to `x509_load_certificate_list'
  make: *** [Makefile:1169: vmlinux] Error 1

Fixes: e9088629 ("certs: make system keyring depend on x509 parser")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Adam Borowski <kilobyte@angband.pl>

There is nowhere calling `menu_get_root_menu` function,
so remove it.
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Remove unused imported 'os' module.
Signed-off-by: yangxingwu <xingwu.yang@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

cgroup has to be one kernfs dir, otherwise kernel panic is caused,
especially cgroup id is provide from userspace.
Reported-by: Marco Patalano <mpatalan@redhat.com>
Fixes: 6b658c48 ("scsi: cgroup: Add cgroup_get_from_id()")
Cc: Muneendra <muneendra.kumar@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Mukesh Ojha <quic_mojha@quicinc.com>
Cc: stable@vger.kernel.org # v5.14+
Signed-off-by: Tejun Heo <tj@kernel.org>

Pull driver core fixes from Greg KH:
 "Here are two tiny driver core fixes for 6.0-rc7 that resolve some
  oft-reported problems.

  The first is a revert of the "fw_devlink.strict=1" default option that
  we keep trying to enable, but we keep finding platforms that this just
  breaks everything on. So again, we need it reverted and hopefully it
  can be worked on in future releases.

  The second is a sysfs file-size bugfix that resolves an issue that
  many people are starting to hit as the fix it is fixing also was
  backported to stable kernels. The util-linux developers are starting
  to get bugreports about sysfs files that contain no data because of
  this problem, and this fix which has been in linux-next in the
  bitfield tree for a long time, resolves it. I'm submitting it here as
  it needs to be merged for 6.0-final, not for 6.1-rc1.

  Both of these have been in linux-next with no reported issues, only
  reports were that these fixed problems"

* tag 'driver-core-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  drivers/base: Fix unsigned comparison to -1 in CPUMAP_FILE_MAX_BYTES
  Revert "driver core: Set fw_devlink.strict=1 by default"

Pull USB / Thunderbolt driver fixes and ids from Greg KH:
 "Here are a few small USB and Thunderbolt driver fixes and new device
  ids for 6.0-rc7.

  They contain:

   - new usb-serial driver ids

   - documentation build warning fix in USB hub code

   - flexcop-usb long-posted bugfix (the v4l maintainer for this is MIA
     so I have finally picked this up as it is a fix for a reported
     problem.)

   - dwc3 64bit DMA bugfix

   - new thunderbolt device ids

   - typec build error fix

  All of these have been in linux-next with no reported issues"

* tag 'usb-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: anx7411: Fix build error without CONFIG_POWER_SUPPLY
  media: flexcop-usb: fix endpoint type check
  USB: serial: option: add Quectel RM520N
  USB: serial: option: add Quectel BG95 0x0203 composition
  thunderbolt: Add support for Intel Maple Ridge single port controller
  usb: dwc3: core: leave default DMA if the controller does not support 64-bit DMA
  USB: core: Fix RST error in hub.c

Pull landlock fix from Mickaël Salaün:
 "Fix out-of-tree builds for Landlock tests"

* tag 'landlock-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
  selftests/landlock: Fix out-of-tree builds

Pull RISC-V fixes from Palmer Dabbelt:

 - A handful of build fixes for the T-Head errata, including some
   functional issues the compilers found

 - A fix for a nasty sigreturn bug

* tag 'riscv-for-linus-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: Avoid coupling the T-Head CMOs and Zicbom
  riscv: fix a nasty sigreturn bug...
  riscv: make t-head erratas depend on MMU
  riscv: fix RISCV_ISA_SVPBMT kconfig dependency warning
  RISC-V: Clean up the Zicbom block size probing

Pull kvm fixes from Paolo Bonzini:
 "As everyone back came back from conferences, here are the pending
  patches for Linux 6.0.

  ARM:

   - Fix for kmemleak with pKVM

  s390:

   - Fixes for VFIO with zPCI

   - smatch fix

  x86:

   - Ensure XSAVE-capable hosts always allow FP and SSE state to be
     saved and restored via KVM_{GET,SET}_XSAVE

   - Fix broken max_mmu_rmap_size stat

   - Fix compile error with old glibc that doesn't have gettid()"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Inject #UD on emulated XSETBV if XSAVES isn't enabled
  KVM: x86: Always enable legacy FP/SSE in allowed user XFEATURES
  KVM: x86: Reinstate kvm_vcpu_arch.guest_supported_xcr0
  KVM: x86/mmu: add missing update to max_mmu_rmap_size
  selftests: kvm: Fix a compile error in selftests/kvm/rseq_test.c
  KVM: s390: pci: register pci hooks without interpretation
  KVM: s390: pci: fix GAIT physical vs virtual pointers usage
  KVM: s390: Pass initialized arg even if unused
  KVM: s390: pci: fix plain integer as NULL pointer warnings
  KVM: arm64: Use kmemleak_free_part_phys() to unregister hyp_mem_base

Pull xen fix from Juergen Gross:
 "A single fix for an issue in the xenbus driver (initialization of
  multi-page rings for Xen PV devices)"

* tag 'for-linus-6.0-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/xenbus: fix xenbus_setup_ring()

Pull drm fixes from Dave Airlie:
 "Regular fixes for the week, i915, mediatek, hisilicon, mgag200 and
  panel have some small fixes.

  amdgpu has more stack size fixes for clang build, and fixes for new
  IPs, but all with low regression chances since they are for stuff new
  in v6.0.

  i915:
   - avoid a general protection failure when using perf/OA
   - avoid kernel warnings on driver release

  amdgpu:
   - SDMA 6.x fix
   - GPUVM TF fix
   - DCN 3.2.x fixes
   - DCN 3.1.x fixes
   - SMU 13.x fixes
   - Clang stack size fixes for recently enabled DML code
   - Fix drm dirty callback change on non-atomic cases
   - USB4 display fix

  mediatek:
   - dsi: Add atomic {destroy,duplicate}_state, reset callbacks
   - dsi: Move mtk_dsi_stop() call back to mtk_dsi_poweroff()
   - Fix wrong dither settings

  hisilicon:
   - Depend on MMU

  mgag200:
   - Fix console on G200ER

  panel:
   - Fix innolux_g121i1_l01 bus format"

* tag 'drm-fixes-2022-09-23-1' of git://anongit.freedesktop.org/drm/drm: (30 commits)
  MAINTAINERS: switch graphics to airlied other addresses
  drm/mediatek: dsi: Move mtk_dsi_stop() call back to mtk_dsi_poweroff()
  drm/amd/display: Reduce number of arguments of dml314's CalculateFlipSchedule()
  drm/amd/display: Reduce number of arguments of dml314's CalculateWatermarksAndDRAMSpeedChangeSupport()
  drm/amdgpu: don't register a dirty callback for non-atomic
  drm/amd/pm: drop the pptable related workarounds for SMU 13.0.0
  drm/amd/pm: add support for 3794 pptable for SMU13.0.0
  drm/amd/display: correct num_dsc based on HW cap
  drm/amd/display: Disable OTG WA for the plane_state NULL case on DCN314
  drm/amd/display: Add shift and mask for ICH_RESET_AT_END_OF_LINE
  drm/amd/display: increase dcn315 pstate change latency
  drm/amd/display: Fix DP MST timeslot issue when fallback happened
  drm/amd/display: Display distortion after hotplug 5K tiled display
  drm/amd/display: Update dummy P-state search to use DCN32 DML
  drm/amd/display: skip audio setup when audio stream is enabled
  drm/amd/display: update gamut remap if plane has changed
  drm/amd/display: Assume an LTTPR is always present on fixed_vs links
  drm/amd/display: fix dcn315 memory channel count and width read
  drm/amd/display: Fix double cursor on non-video RGB MPO
  drm/amd/display: Only consider pixle rate div policy for DCN32+
  ...