Add irqchip calls to set/get interrupt state from the parent interrupt
controller. When GPIOs are renabled as interrupt lines, it is desirable
to clear the interrupt state at the GIC. This avoids any unwanted
interrupt as a result of stale pending state recorded when the line was
used as a GPIO.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
[Lina: updated commit text, rearranged code]
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-8-git-send-email-ilina@codeaurora.org

Introduce a new domain for wakeup capable GPIOs. The domain can be
requested using the bus token DOMAIN_BUS_WAKEUP. In the following
patches, we will specify PDC as the wakeup-parent for the TLMM GPIO
irqchip. Requesting a wakeup GPIO will setup the GPIO and the
corresponding PDC interrupt as its parent.
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-5-git-send-email-ilina@codeaurora.org

When an interrupt is to be serviced, the convention is to mask the
interrupt at the chip and unmask after servicing the interrupt. Enabling
and disabling the interrupt at the PDC irqchip causes an interrupt storm
due to the way dual edge interrupts are handled in hardware.

Skip configuring the PDC when the IRQ is masked and unmasked, instead
use the irq_enable/irq_disable callbacks to toggle the IRQ_ENABLE
register at the PDC. The PDC's IRQ_ENABLE register is only used during
the monitoring mode when the system is asleep and is not needed for
active mode detection.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-4-git-send-email-ilina@codeaurora.org

Newer SoCs have increased the number of interrupts routed to the PDC
interrupt controller. Update the definition of max PDC interrupts.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-3-git-send-email-ilina@codeaurora.org

Some interrupt controllers in a SoC, are always powered on and have a
select interrupts routed to them, so that they can wakeup the SoC from
suspend. Add wakeup-parent DT property to refer to these interrupt
controllers.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-6-git-send-email-ilina@codeaurora.org

On certain QTI chipsets some GPIOs are direct-connect interrupts to the
GIC to be used as regular interrupt lines. When the GPIOs are not used
for interrupt generation the interrupt line is disabled. But disabling
the interrupt at GIC does not prevent the interrupt to be reported as
pending at GIC_ISPEND. Later, when drivers call enable_irq() on the
interrupt, an unwanted interrupt occurs.

Introduce get and set methods for irqchip's parent to clear it's pending
irq state. This then can be invoked by the GPIO interrupt controller on
the parents in it hierarchy to clear the interrupt before enabling the
interrupt.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-7-git-send-email-ilina@codeaurora.org

[updated commit text and minor code fixes]

A single controller can handle normal interrupts and wake-up interrupts
independently, with a different numbering space. It is thus crucial to
allow the driver for such a controller discriminate between the two.

A simple way to do so is to tag the wake-up irqdomain with a "bus token"
that indicates the wake-up domain. This slightly abuses the notion of
bus, but also radically simplifies the design of such a driver. Between
two evils, we choose the least damaging.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-2-git-send-email-ilina@codeaurora.org

A coccicheck run provided information like the following.

drivers/irqchip/irq-ti-sci-inta.c:250:9-16: WARNING: ERR_CAST can be used
with vint_desc.

Generated by: scripts/coccinelle/api/err_cast.cocci

Thus adjust the exception handling in one if branch.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/776b7135-26af-df7d-c3a9-4339f7bf1f15@web.de

Add process for the situation that more than one irq is coming to
a single chip at the same time. The original code will only respond
to the lowest setted bit in JZ_REG_INTC_PENDING, and then exit the
interrupt dispatch function. After exiting the interrupt dispatch
function, since the second interrupt has not yet responded, the
interrupt dispatch function is again entered to process the second
interrupt. This creates additional unnecessary overhead, and the
more interrupts that occur at the same time, the more overhead is
added. The improved method in this patch is to check whether there
are still unresponsive interrupts after processing the lowest
setted bit interrupt. If there are any, the processing will be
processed according to the bit in JZ_REG_INTC_PENDING, and the
interrupt dispatch function will be exited until all processing
is completed.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/1570015525-27018-6-git-send-email-zhouyanjie@zoho.com

By creating the generic chips from the IRQ domain, we don't rely on the
JZ4740_IRQ_BASE macro. It also makes the code a bit cleaner.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1570015525-27018-5-git-send-email-zhouyanjie@zoho.com

Get the virq number from the IRQ domain instead of calculating it from
the hardcoded irq base.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1570015525-27018-4-git-send-email-zhouyanjie@zoho.com

If we cannot create the IRQ domain, the driver should fail to probe
instead of succeeding with just a warning message.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1570015525-27018-3-git-send-email-zhouyanjie@zoho.com

The same behaviour can be obtained by using the IRQCHIP_MASK_ON_SUSPEND
flag on the IRQ chip.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1570015525-27018-2-git-send-email-zhouyanjie@zoho.com

Somehow CONFIG_SIFIVE_PLIC ended up outside of the "IRQ chip support"
menu.

Fixes: 8237f8bc ("irqchip: add a SiFive PLIC driver")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Link: https://lore.kernel.org/r/20191002144452.10178-1-j.neuschaefer@gmx.net

The VLPI map is currently a mutex, and that's a bad idea as
this lock can be taken in non-preemptible contexts. Convert
it to a raw spinlock, and turn the memory allocation of the
VLPI map to be atomic.
Reported-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191108165805.3071-12-maz@kernel.org

Obtaining the mapping ivformation for a VLPI should always be
done with the vlpi_lock for this device held. Otherwise, we
expose ourselves to races against a concurrent unmap.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191108165805.3071-11-maz@kernel.org

We have so far always injected/cleared VLPIs using either
INT+SYNC or CLEAR+SYNC sequences, but that's pretty wrong
for two reasons:

- SYNC only synchronises physical LPIs
- The collection ID that for the associated LPI doesn't match
  the redistributor the vPE is associated with

Instead, send an {INT,CLEAR}+VSYNC for forwarded LPIs, ensuring
that the ITS synchronises against the virtual pending table.
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191108165805.3071-10-maz@kernel.org

We have so far alwways invalidated VLPIs usinc an INV+SYNC
sequence, but that's pretty wrong for two reasons:

- SYNC only synchronises physical LPIs
- The collection ID that for the associated LPI doesn't match
  the redistributor the vPE is associated with

Instead, send an INV+VSYNC for forwarded LPIs, ensuring that
the ITS can properly synchronise the invalidation of VLPIs.

Fixes: 015ec038 ("irqchip/gic-v3-its: Add VLPI configuration handling")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191108165805.3071-9-maz@kernel.org

Obtaining the mapping information for a VLPI is something quite common,
and the GICv4.1 code is going to make even more use of it. Expose it as
a separate set of helpers.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191027144234.8395-8-maz@kernel.org
Link: https://lore.kernel.org/r/20191108165805.3071-8-maz@kernel.org

Now that we have a copy of TYPER in the ITS structure, rely on this
to provide the same service as its->device_ids, which gets axed.
Errata workarounds are now updating the cached fields instead of
requiring a separate field in the ITS structure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191027144234.8395-7-maz@kernel.org
Link: https://lore.kernel.org/r/20191108165805.3071-7-maz@kernel.org

Now that we have a copy of TYPER in the ITS structure, rely on this
to provide the same service as its->ite_size, which gets axed.
Errata workarounds are now updating the cached fields instead of
requiring a separate field in the ITS structure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191027144234.8395-6-maz@kernel.org
Link: https://lore.kernel.org/r/20191108165805.3071-6-maz@kernel.org

Instead of caching the GICv4 compatibility in a discrete way, cache the
TYPER register instead, which can then be used to implement the same
functionnality. This will get used more extensively in subsequent patches.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191027144234.8395-5-maz@kernel.org
Link: https://lore.kernel.org/r/20191108165805.3071-5-maz@kernel.org

We currently don't make much use of the DirectLPI feature, and it would
be beneficial to do this more, if only because it becomes a mandatory
feature for GICv4.1.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191027144234.8395-4-maz@kernel.org
Link: https://lore.kernel.org/r/20191108165805.3071-4-maz@kernel.org

Waiting for a redistributor to have performed an operation is a
common thing to do, and the idiom is already spread around.
As we're going to make even more use of this, let's have a primitive
that does just that.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191027144234.8395-3-maz@kernel.org
Link: https://lore.kernel.org/r/20191108165805.3071-3-maz@kernel.org

We allocate the collection mapping on device creation, but somehow
free it on the irqdomain free path, which is pretty inconsistent
and has led to bugs in the past.

Move it to the point where we teardown the device, making the
alloc/free symetric.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191108165805.3071-2-maz@kernel.org

Add the compatible string for sc7180 SoC from Qualcomm.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191108092824.9773-8-rnayak@codeaurora.org

Remove the sdm845 SoC specific compatible to make the driver
easily reusable across other SoC's with the same IP block.
This will reduce further churn adding any SoC specific
compatibles unless really needed.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191108092824.9773-7-rnayak@codeaurora.org

The LS1021A allows inverting the polarity of six interrupt lines
IRQ[0:5] via the scfg_intpcr register, effectively allowing
IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_EDGE_FALLING for those. We just need to
check the type, set the relevant bit in INTPCR accordingly, and fixup
the type argument before calling the GIC's irq_set_type.

In fact, the power-on-reset value of the INTPCR register on the LS1021A
is so that all six lines have their polarity inverted. Hence any
hardware connected to those lines is unusable without this: If the line
is indeed active low, the generic GIC code will reject an irq spec with
IRQ_TYPE_LEVEL_LOW, while if the line is active high, we must obviously
disable the polarity inversion (writing 0 to the relevant bit) before
unmasking the interrupt.

Some other Layerscape SOCs (LS1043A, LS1046A) have a similar feature,
just with a different number of external interrupt lines (and a
different POR value for the INTPCR register). This driver should be
prepared for supporting those by properly filling out the device tree
node. I have the reference manuals for all three boards, but I've only
tested the driver on an LS1021A.

Unfortunately, the Kconfig symbol ARCH_LAYERSCAPE only exists on
arm64, so do as is done for irq-ls-scfg-msi.c: introduce a new symbol
which is set when either ARCH_LAYERSCAPE or SOC_LS1021A is set.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191107122115.6244-3-linux@rasmusvillemoes.dk

This adds Device Tree binding documentation for the external interrupt
lines with configurable polarity present on some Layerscape SOCs.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191107122115.6244-2-linux@rasmusvillemoes.dk

On some specific chips like 7211 we need to leave some interrupts
untouched/forwarded to the VPU which is another agent in the system
making use of that interrupt controller hardware (goes to both ARM GIC
and VPU L1 interrupt controller). Make that possible by using the
existing brcm,int-fwd-mask property and take necessary actions to avoid
masking that interrupt as well as not allowing Linux to map them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-6-f.fainelli@gmail.com

Indicate that the brcm,int-fwd-mask property is optional and can be set
on platforms which require to leave specific interrupts unmanaged by
Linux and need to retain the firmware configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-5-f.fainelli@gmail.com

If the 'brcm,irq-can-wake' property is specified, make sure we also
enable the corresponding parent interrupt we are attached to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-4-f.fainelli@gmail.com

The BCM7038 L1 interrupt controller can be used as a wake-up interrupt
controller on MIPS and ARM-based systems, document the brcm,irq-can-wake
which has been "standardized" across Broadcom interrupt controllers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-3-f.fainelli@gmail.com

The current L1 controller does not mask any interrupts when dropping
into suspend. This mean we can receive unexpected wake up sources.
Modified the BCM7038 L1 controller to mask the all non-wake interrupts
before dropping into suspend.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-2-f.fainelli@gmail.com

The __iomem attribute should go before the * in the
prototype. Move to silence the following sparse
warnings:

./arch/arm/include/asm/arch_gicv3.h:340:15: warning: incorrect type in argument 1 (different address spaces)
./arch/arm/include/asm/arch_gicv3.h:340:15:    expected void const volatile [noderef] <asn:2> *addr
./arch/arm/include/asm/arch_gicv3.h:340:15:    got void *
./arch/arm/include/asm/arch_gicv3.h:343:17: warning: incorrect type in argument 2 (different address spaces)
./arch/arm/include/asm/arch_gicv3.h:343:17:    expected void volatile [noderef] <asn:2> *addr
./arch/arm/include/asm/arch_gicv3.h:343:17:    got void *
./arch/arm/include/asm/arch_gicv3.h:350:37: warning: incorrect type in argument 2 (different address spaces)
./arch/arm/include/asm/arch_gicv3.h:350:37:    expected void volatile [noderef] <asn:2> *addr
./arch/arm/include/asm/arch_gicv3.h:350:37:    got void *[noderef] <asn:2> addr
drivers/irqchip/irq-gic-v3-its.c:2832:46: warning: incorrect type in argument 2 (different address spaces)
drivers/irqchip/irq-gic-v3-its.c:2832:46:    expected void *[noderef] <asn:2> addr
drivers/irqchip/irq-gic-v3-its.c:2832:46:    got void [noderef] <asn:2> *
./arch/arm/include/asm/arch_gicv3.h:340:15: warning: incorrect type in argument 1 (different address spaces)
./arch/arm/include/asm/arch_gicv3.h:340:15:    expected void const volatile [noderef] <asn:2> *addr
./arch/arm/include/asm/arch_gicv3.h:340:15:    got void *
./arch/arm/include/asm/arch_gicv3.h:343:17: warning: incorrect type in argument 2 (different address spaces)
./arch/arm/include/asm/arch_gicv3.h:343:17:    expected void volatile [noderef] <asn:2> *addr
./arch/arm/include/asm/arch_gicv3.h:343:17:    got void *
./arch/arm/include/asm/arch_gicv3.h:350:37: warning: incorrect type in argument 2 (different address spaces)
./arch/arm/include/asm/arch_gicv3.h:350:37:    expected void volatile [noderef] <asn:2> *addr
./arch/arm/include/asm/arch_gicv3.h:350:37:    got void *[noderef] <asn:2> addr
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191017113341.13778-1-ben.dooks@codethink.co.uk

The its_cmd_block struct can either have u64 or __le64
data in it, so make a anonymous union to remove the
sparse warnings when converting to/from these.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191017112955.15853-1-ben.dooks@codethink.co.uk

check drivers/irqchip with "make coccicheck M=drivers/irqchip/",
it will report unneeded semicolon like below, just remove them.

drivers/irqchip/irq-zevio.c:54:2-3: Unneeded semicolon
drivers/irqchip/irq-gic-v3.c:177:2-3: Unneeded semicolon
drivers/irqchip/irq-gic-v3.c:234:2-3: Unneeded semicolon
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1571300729-38822-1-git-send-email-huangdaode@hisilicon.com

Pull x86 fixes from Thomas Gleixner:
 "Two fixes for the VMWare guest support:

   - Unbreak VMWare platform detection which got wreckaged by converting
     an integer constant to a string constant.

   - Fix the clang build of the VMWAre hypercall by explicitely
     specifying the ouput register for INL instead of using the short
     form"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu/vmware: Fix platform detection VMWARE_PORT macro
  x86/cpu/vmware: Use the full form of INL in VMWARE_HYPERCALL, for clang/llvm

Pull timer fixes from Thomas Gleixner:
 "A small set of fixes for time(keeping):

   - Add a missing include to prevent compiler warnings.

   - Make the VDSO implementation of clock_getres() POSIX compliant
     again. A recent change dropped the NULL pointer guard which is
     required as NULL is a valid pointer value for this function.

   - Fix two function documentation typos"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Fix two trivial comments
  timers/sched_clock: Include local timekeeping.h for missing declarations
  lib/vdso: Make clock_getres() POSIX compliant again