This touchscreen does not seem to be inverted in any axis, so remove these
DT properties.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit changes the default brightness level of the backlight on the
prtvt7 device from 20 to 65, roughly equivalent to 75% of the maximum
brightness level defined in the "brightness-levels" property.

The adjustment provides a more optimal default brightness for the
device, improving the overall user experience.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
'fsl,mode' should be specified for AC97 mode only.

The 'fsl,ssi' documentation doesn't say anything about specifying
'sound-dai-cells' so we'll remove that as well.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Devicetree node names should be generic. Use 'eeprom' as node name
to avoid devicetree check warning from at24.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As documented in pfuze100.yaml, the correct name for the regulator is
"coin", so change it to fix the following DT check warning:

imx6ul-ccimx6ulsbcexpress.dtb: pmic@8: regulators: 'vcoin' does not match any of the regexes:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Devicetree node names should be generic. Use 'pmic' as node name
to avoid devicetree check warning from pfuze100.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Documentation/devicetree/bindings/sound/imx-audmux.yaml,
there must be a "mux-" prefix in the audmux port nodes.

Add the "mux-" prefix to avoid devicetree schema warnings.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Describe the SD1_VSELECT pad, which is necessary to allow UHS modes.

Also, to support higher SD card speed modes, describe the 100MHz and
200MHz SD card pinctrl entries.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Improve the devicetree description by adding the SD card regulator
that is controlled via GPIO5_2.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Vybrid FEC is a Fast Ethrnet using RMII.

Additionally, the cpu label has never actually been used in the
binding, so remove it.

Lastly, for DSA links between switches, add a fixed-link node
indicating the expected speed/duplex of the link.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

'vmcc-supply' is not a valid property.

Use 'vmmc-supply' supply instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'clock-names' property is not a valid property for wdog.

Remove it to fix the following DT check warning:

vf610-zii-ssmb-dtu.dtb: watchdog@4003e000: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: /Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'clock-names' property is not a valid property for wdog.

Remove it to fix the following DT check warning:

watchdog@53fdc000: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'num-chipselects' property is not a valid property for ecspi.

Remove it to fix the following DT check warning:

spi@30630000: Unevaluated properties are not allowed ('num-chipselects' was unexpected)
From schema: Documentation/devicetree/bindings/spi/fsl-imx-cspi.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'rs485-rts-active-high' property is not a valid property and is not
documented anywhere.

Remove it to fix the following DT schema warning:

serial@21f0000: Unevaluated properties are not allowed ('rs485-rts-active-high' was unexpected)
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass Ethernet aliases, so that the bootloader can properly pass MAC address
to Linux.

This fixes the problem of getting a random MAC address for eth1 in Linux.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use pinctrl-0 for pinctrl_rfkill to fix the following
'make CHECK_DTBS=y imx7d-smegw01.dtb' warning:

regulator-wlan-rfkill: 'pinctrl-0' is a dependency of 'pinctrl-names'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass 'gpr' to the pinctrl groups to fix the following
'make CHECK_DTBS=y imx7d-smegw01.dtb' warning:

pinctrl@30330000: 'rfkillrp', 'usbotg1', 'usbotg1-pwr', 'usbotg1-pwr-gpio' do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the unneeded #address-cells/#size-cells from sram@0 to fix
the following 'make CHECK_DTBS=y imx7d-smegw01.dtb' warning:

sram@0: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
From schema: Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the invalid #address-cells and #size-cells nodes from
the fan-controller.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the invalid #address-cells and #size-cells nodes from
the fan-controller.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6SX has an LVDS controller that is connected to the eLCDIF.

Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

usdhc1 and usdhc3 node name contain underscores, so replace the
'_' by '-'.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On imx6sll-evk board, eMMC is connect on the usdhc2.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for a COTS monitor connected to X17.
4k monitors can be used, but are limited to 1080p.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The mac address is stored in mainboard eeprom.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The OCOTP node should have address/size-cells so the cells can have unit
address:

  imx7ulp-evk.dtb: efuse@410a6000: '#address-cells' is a required property
  imx7ulp-evk.dtb: efuse@410a6000: '#size-cells' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This fixes the warnings:
pca953x 3-0020: supply vcc not found, using dummy regulator
pca953x 3-0021: supply vcc not found, using dummy regulator
pca953x 3-0022: supply vcc not found, using dummy regulator
at24 3-0051: supply vcc not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to fsl,imx-gpc.yaml the General Power Control requires
a ipg clock and a Power Gating Control node. So add them to fix
the dtbs_check warnings on i.MX6UL boards:

gpc@20dc000: 'clocks' is a required property
gpc@20dc000: 'clock-names' is a required property
gpc@20dc000: 'pgc' is a required property
Suggested-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently the dtbs_check generates warnings like this:

$nodename:0: 'dma-apbh@110000' does not match '^dma-controller(@.*)?$'

So fix all affected dma-apbh node names.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DSA framework has got more picky about always having a phy-mode
for the CPU port. Add a phy-mode based on what the SoC ethernet is
using. For RGMII mode, have the switch add the delays.

Additionally, the cpu label has never actually been used in the
binding, so remove it.

Lastly add a fixed-link node indicating the expected speed/duplex of
the link to the SoC.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DSA framework has got more picky about always having a phy-mode
for the CPU port. The imx51 Ethernet supports MII, and RMII. Set the
switch phy-mode based on how the SoC Ethernet port has been
configured.

Additionally, the cpu label has never actually been used in the
binding, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As stated in Documentation/devicetree/bindings/spi/spi-gpio.yaml,
'gpio-miso', 'gpio-mosi' and 'gpio-sck' are deprecated properties.

Use the recommeded 'miso-gpios', 'mosi-gpios' and 'sck-gpios' instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As stated in Documentation/devicetree/bindings/spi/spi-gpio.yaml,
'gpio-miso', 'gpio-mosi' and 'gpio-sck' are deprecated properties.

Use the recommeded 'miso-gpios', 'mosi-gpios' and 'sck-gpios' instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As stated in Documentation/devicetree/bindings/spi/spi-gpio.yaml,
'gpio-miso', 'gpio-mosi' and 'gpio-sck' are deprecated properties.

Use the recommeded 'miso-gpios', 'mosi-gpios' and 'sck-gpios' instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As stated in Documentation/devicetree/bindings/spi/spi-gpio.yaml,
'gpio-miso', 'gpio-mosi' and 'gpio-sck' are deprecated properties.

Use the recommeded 'miso-gpios', 'mosi-gpios' and 'sck-gpios' instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As stated in Documentation/devicetree/bindings/spi/spi-gpio.yaml,
'gpio-miso', 'gpio-mosi' and 'gpio-sck' are deprecated properties.

Use the recommeded 'miso-gpios', 'mosi-gpios' and 'sck-gpios' instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As stated in Documentation/devicetree/bindings/spi/spi-gpio.yaml,
'gpio-mosi' and 'gpio-sck' are deprecated properties.

Use the recommeded 'mosi-gpios' and 'sck-gpios' instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As stated in Documentation/devicetree/bindings/spi/spi-gpio.yaml,
'gpio-mosi' and 'gpio-sck' are deprecated properties.

Use the recommeded 'mosi-gpios' and 'sck-gpios' instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Marantec maveo box. The system is used to get a
smart conntection to a door drive. It has USB, WiFi, Bluetooth,
Zigbee and NFC interfaces. The core of this system is a soldered
i.MX6ULL DHCOR SoM from DH electronics.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>