Remove /omit-if-no-ref/ from node usdhc1-pwrseq, because if the compile
flag -@ (include symbols) is used the node will always be there. In this
case, GPIO H is not released and therefore cannot be used. Therefore,
remove this node manually from the corresponding devicetree file and
don't rely on /omit-if-no-ref/.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the new Apalis Evaluation Board v1.2. Because
only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi
has been created which has common hardware configurations for v1.0, v1.1
and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts
files include imx6q-apalis-eval.dtsi.

Versions 1.0 and 1.1 are compatible with each other and should
use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file
should be used.
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add aliases for all ethernet nodes including the switch. It makes it
easier to find this nodes by the boot loader.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

HummingBoard has two RTCs, first integrated within SoC that can be used to
wake up from sleep - and a second on the carrier board including back-up
battery which is intended for keeping time during power-off.

Add aliases for both, ensuring that the battery-backed clock is primary
rtc and used by default during boot for restoring system time.

Fixes keeping time across power-cycle observed on Debian,
which sets RTC_HCTOSYS_DEVICE="rtc0".
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Sielaff i.MX6 Solo board is used as controller and user interface
in vending machines. It is based on the i.MX6 Solo SoC and features
the following peripherals and interfaces:

* 512 MB DDR3 RAM
* 512 MB NAND Flash
* 1 MB NOR Flash
* SD card
* Debug LED
* Debug UART
* Key Inputs
* RTC
* RS232
* 100 MBit Ethernet
* USB Hub
* USB OTG
* HDMI
* 7" LVDS IPS panel
* PWM Backlight
* Optional Extension Board with USB Ethernet NIC
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixes the dtbs_check warning:
  tempmon: '#thermal-sensor-cells' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The display is in landscape orientation, but the touchscreen is in portrait
orientation. Specify that properly in the devicetree.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Due to CPU lifetime consideration of the SoC manufacturer [1] and
the preferred area of operation in the industrial related
environment, set the maximum frequency for each DHCOM i.MX6ULL to
792MHz, as with the industrial type. This is done by removing the
operating point at 900MHz and set the clock-frequency to 792000000.

[1] https://www.nxp.com/docs/en/application-note/AN5337.pdfSigned-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

regulator-*-microvolt is not the range the regulator supports, but the
range which the regulator is allowed to configure. Limit v33 rail to
3.3V only.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixes the warnings:
pca953x 1-0020: supply vcc not found, using dummy regulator
lm75 0-0049: supply vs not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fixes the warnings:
at24 0-0050: supply vcc not found, using dummy regulator
at24 0-0056: supply vcc not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These properties are only used on USB OTG/DR devices, remove them from
a host only device.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

temperature-sensor is the recommended node name and its main purpose.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is manufacturer data and shall not be modified.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

SDMA is enabled by default, so remove the status property.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

USDHC3 is directly connected to an eMMC, so disable other interface modes.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

USDHC1 is directly connected to an SD card, so disable other interface modes.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node name must end with 'grp'
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node name must end with 'grp'
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

0x56 is the EEPROM component of SE97BTP.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the pin muxing and GPIO settings for SCL/SDA for i2c2 & i2c3.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the pin muxing and GPIO settings for SCL/SDA for i2c1.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ECSPI1.SS0 was missing in the list.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Ensure the RTC devices are numbered correctly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This allows using S10 for power down / shutdown.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

I2C expander is capable of generating an IRQ during powersave, so the
attached buttons can be used for waking up the system.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

PCIE_DIS & PCIE_RST (correctly named W_DISABLE# & PERST#) affect USB
devices as well. So hog them to make USB devices attached to Mini PCIe
connector available, despite PCIe being disabled.
Supply voltages are enabled unconditionally.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Using internal PHY refclk is not supported yet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

USB host is an HSIC interface directly connected to a USB hub. USB OTG2
is a direct connection to Mini PCIe interface without any OC signaling.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Split pinctrl as well. 'reset-deassert-us' is added with a small safe
margin.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

make dtbs_check does not warn about this anymore, but bindings mandate
a uint32-matrix.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB

Add line breaks - inode_to_text() is now much easier to read.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>