ISP24xx and above ISPs perform a RISC reset in
qla24xx_reset_chip(), which is called prior to
qla24xx_chip_diag().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

With RSCN states not being kept across qla2x00_configure_loop()
invocations, loop-resync distruptions during fabric-discovery may
cause ports to remain in a lost state.  Force state
renegotiation during a follow-on configure-loop iteration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Unlike earlier ISPs, recent ISPs (ISP81xx) can in fact fail this
mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

This patch fixes a NULL pointer bug that occurs when IO is being
carried out on a vport for which the cpu affinity mode is turned on.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

The SCSI-midlayer's fast-fail codes consider an DID_ERROR status
as a driver-error and the failed I/O would then be retried in the
midlayer without being fast-failed to dm-multipath.  DID_BUS_BUSY
status returns would induce unneeded path-failures events being
propagated to the DM/MD.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

In case the onboard firmware is unable to be read or loaded for
operation, attempt to fallback to a limited-operational firmware
image stored in a different flash region.  This will allow a user
to reflash and correct a board with proper operational firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Firmware currently provides PB and PGF TLVs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

FIP is the FCoE Initialization Protocol and this patch
adds the protocol ethertype to the kernel's list of
ethertypes.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

This is not required as VLAN header is added by device
interface driver, this was causing bad FC_CRC in FCoE pkts when
using VLAN interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Removes periodic fcoe_watchdog timer used across all fcoe interface
maintained in fcoe_hostlist instead added new fcoe_queue_timer
per fcoe interface.

Added timer is armed only when some pending skb need to be flushed
as oppose to periodic 1 second fcoe_watchdog, since now
fcoe_queue_timer is used on demand thus set this to 2 jiffies.

Now fcoe_queue_timer is much simple than fcoe_watchdog using lock to
process all fcoe interface from fcoe_hostlist.

I noticed +ve performance result with using 2 jiffies timer as
this helps flushing fcoe_pending_queue quickly.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Currently fcoe_pending_queue.lock held twice for every new skb
adding to this queue when already least one pkt is pending in this
queue and that is not uncommon once skb pkts starts getting queued
here upon fcoe_start_io => dev_queue_xmit failure.

This patch moves most fcoe_pending_queue logic to fcoe_check_wait_queue
function, this new logic grabs fcoe_pending_queue.lock only once to
add a new skb instead twice as used to be.

I think after this patch call flow around fcoe_check_wait_queue
calling in fcoe_xmit is bit simplified with modified
fcoe_check_wait_queue function taking care of adding and
removing pending skb in one function.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

When a sequence is received in response to an exchange we issued previously,
we should check to see if the exchange has completed. If yes, the sequence
should be discarded. Since the exchange might be still in the completion
process, it should be untouched.
Signed-off-by: Steve Ma <steve.ma@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

If we aborted a command, because it timed out we should not use
DID_ABORT. It will fail the command right away back to the upper
layer. We want to use something that indicated that the problem
did not complete normally, but it was not a fatal problem.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

FIP frames should leave the fcoe layer with skb->protocol set to
ETH_P_FIP, not ETH_P_802_3.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

When a reset is sent using fcoeadm on a non-FIP mode NIC,
there's no link flap, so the fcoe_ctlr stays in non-FIP mode.

In that case, FIP wasn't setting the flogi_oxid or map_dest flag,
causing the FLOGI to be sent with the both wrong source MAC and
the wrong destination MAC address, causing it to fail.

This leads to a non-functioning HBA until a link flap or
instance delete/create.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

This driver needs dst_cache->dev so it should include net/dst.h
to ensure that it builds.  While net/tcp.h probably includes it
already, we shouldn't rely on that since there is no guarantee
that this won't change in future.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Bump driver version
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

There are several scenarios where the ibmvfc driver needs to
try to log back into a target on the fabric. Today when these events
occur, we simply go through re-discovery for all attached targets,
assuming that either the query of the name server or an ADISC will
indicate we might need to log back into the target, which doesn't
work for all scenarios. Fix this by taking note of the affected target(s)
in these conditions and ensuring we try to PLOGI back into the target.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

For certain scenarios during device rediscovery, we detect we need
to log back into a target. Currently we do just that - PLOGI/PRLI
back into the target. Change the code to delete and add the target
from the FC transport layer as well, to ensure we handle any cases
where the target may have changed.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

The virtual I/O server controlling the NPIV adapter associated with
a virtual fibre channel adapter can send a HALT event to the client.
When this occurs, the client can no longer send commands until a RESUME
is received. By adding support for flush on halt, we will get all of
our outstanding commands flushed back before the Virtual I/O server
enters the halt state, eliminating potential command timeouts for
outstanding commands which might occur if we did not support this feature.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

This patch adds support for a new command supported by the Virtual I/O
Server, NPIV Logout. The command will abort all outstanding commands
and log out of the fabric. Currently, the only way to do this is
by breaking the CRQ, which can take a fairly long time when lots of
commands are outstanding. The NPIV Logout commands provides a mechanism
to accomplish virtually the same function, but is much faster.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Fixes the following deadlock scenario shown below. We currently allow
queuecommand to send commands when the ibmvfc workqueue is scanning for
new rports, so we should also allow EH to function at this time as well.

scsi_eh_3     D 0000000000000000 12304  1279      2
Call Trace:
[c0000002f7257730] [c0000002f72577e0] 0xc0000002f72577e0 (unreliable)
[c0000002f7257900] [c0000000000118f4] .__switch_to+0x158/0x1a0
[c0000002f72579a0] [c0000000004f8b40] .schedule+0x8d4/0x9dc
[c0000002f7257b60] [c0000000004f8f08] .schedule_timeout+0xa8/0xe8
[c0000002f7257c50] [d0000000001d23e0] .ibmvfc_wait_while_resetting+0xe4/0x140 [ibmvfc]
[c0000002f7257d20] [d0000000001d3984] .ibmvfc_eh_abort_handler+0x60/0xe4 [ibmvfc]
[c0000002f7257dc0] [d000000000366714] .scsi_error_handler+0x38c/0x674 [scsi_mod]
[c0000002f7257f00] [c0000000000a7470] .kthread+0x78/0xc4
[c0000002f7257f90] [c000000000029b8c] .kernel_thread+0x4c/0x68
ibmvfc_3      D 0000000000000000 12432  1280      2
Call Trace:
[c0000002f7253540] [c0000002f72535f0] 0xc0000002f72535f0 (unreliable)
[c0000002f7253710] [c0000000000118f4] .__switch_to+0x158/0x1a0
[c0000002f72537b0] [c0000000004f8b40] .schedule+0x8d4/0x9dc
[c0000002f7253970] [c0000000004f8e98] .schedule_timeout+0x38/0xe8
[c0000002f7253a60] [c0000000004f80cc] .wait_for_common+0x138/0x220
[c0000002f7253b40] [c0000000000a2784] .flush_cpu_workqueue+0xac/0xcc
[c0000002f7253c10] [c0000000000a2960] .flush_workqueue+0x58/0xa0
[c0000002f7253ca0] [d0000000000827fc] .fc_flush_work+0x4c/0x64 [scsi_transport_fc]
[c0000002f7253d20] [d000000000082db4] .fc_remote_port_add+0x48/0x6c4 [scsi_transport_fc]
[c0000002f7253dd0] [d0000000001d7d04] .ibmvfc_work+0x820/0xa7c [ibmvfc]
[c0000002f7253f00] [c0000000000a7470] .kthread+0x78/0xc4
[c0000002f7253f90] [c000000000029b8c] .kernel_thread+0x4c/0x68
fc_wq_3       D 0000000000000000 10720  1283      2
Call Trace:
[c0000002f559ac30] [c0000002f559ace0] 0xc0000002f559ace0 (unreliable)
[c0000002f559ae00] [c0000000000118f4] .__switch_to+0x158/0x1a0
[c0000002f559aea0] [c0000000004f8b40] .schedule+0x8d4/0x9dc
[c0000002f559b060] [c0000000004f8e98] .schedule_timeout+0x38/0xe8
[c0000002f559b150] [c0000000004f80cc] .wait_for_common+0x138/0x220
[c0000002f559b230] [c0000000002721c4] .blk_execute_rq+0xb4/0x100
[c0000002f559b360] [d00000000036a1f8] .scsi_execute+0x118/0x194 [scsi_mod]
[c0000002f559b420] [d00000000036a32c] .scsi_execute_req+0xb8/0x124 [scsi_mod]
[c0000002f559b500] [d0000000000c1330] .sd_sync_cache+0x8c/0x108 [sd_mod]
[c0000002f559b5e0] [d0000000000c15b4] .sd_shutdown+0x9c/0x158 [sd_mod]
[c0000002f559b660] [d0000000000c16d0] .sd_remove+0x60/0xb4 [sd_mod]
[c0000002f559b700] [c000000000392ecc] .__device_release_driver+0xd0/0x118
[c0000002f559b7a0] [c000000000393080] .device_release_driver+0x30/0x54
[c0000002f559b830] [c000000000392108] .bus_remove_device+0x128/0x16c
[c0000002f559b8d0] [c00000000038f94c] .device_del+0x158/0x234
[c0000002f559b960] [d00000000036f078] .__scsi_remove_device+0x5c/0xd4 [scsi_mod]
[c0000002f559b9f0] [d00000000036f124] .scsi_remove_device+0x34/0x58 [scsi_mod]
[c0000002f559ba80] [d00000000036f204] .__scsi_remove_target+0xb4/0x120 [scsi_mod]
[c0000002f559bb10] [d00000000036f338] .__remove_child+0x2c/0x44 [scsi_mod]
[c0000002f559bb90] [c00000000038f11c] .device_for_each_child+0x54/0xb4
[c0000002f559bc50] [d00000000036f2e0] .scsi_remove_target+0x70/0x9c [scsi_mod]
[c0000002f559bce0] [d000000000083454] .fc_starget_delete+0x24/0x3c [scsi_transport_fc]
[c0000002f559bd70] [c0000000000a2368] .run_workqueue+0x118/0x208
[c0000002f559be30] [c0000000000a2580] .worker_thread+0x128/0x154
[c0000002f559bf00] [c0000000000a7470] .kthread+0x78/0xc4
[c0000002f559bf90] [c000000000029b8c] .kernel_thread+0x4c/0x68
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

The ibmvfc driver currently logs errors during discovery for several
transient fabric errors, which generally get retried. If retries
do not work, we see multiple errors in the log. If retries do work,
we see errors in the log which may be confusing since the retry worked.
This patch enhances the discovery time error logging to only log errors
for command failures during discovery if all allowed retries have been
used up. The existing behavior of logging all failures can be restored
by setting the hosts log_level to a value of 3 or greater.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Use DEVICE_ATTR macro for defining device sysfs attributes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Since target allocations can occur while resetting the virtual adapter,
we shouldn't be using GFP_KERNEL for them as it could hang. Switch to
use GFP_NOIO.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Fix an obvious bug in processing error responses for SCSI commands
which can result in successful responses being incorrectly returned
with DID_ERROR.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

The async split up of probing in sd.c created a potential failure case where
something goes wrong with device_add(), but which we don't recover properly.
Since, in general, asynchronous error handling is hard, move the device_add()
into the asynchronous path (it should be fast) and make sure all the deferred
processing cannot fail.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

The Documentation is incorrect (we removed some functions referred to), and
none of the bug warnings now apply.  Additionally remove the spurious check on
the return from blk_get_request() which can't fail if __GFP_WAIT is passed in.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Add support for persistent vport definitions at creation at boot time

Also includes a few misc fixes for:
- conversion to vpi name from vport slang name
- couple of small mailbox references
- some additional discovery mods
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Miscellaneous Changes:
- Convert from SLI2_ACTIVE flag to more correct SLI_ACTIVE (generic) flag
- Reposition log verbose messaging definitions
- Update naming for vpi object name from vport slang name
- Handle deferred error attention condition
- Add 10G link support
- Small bug fixup
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Update of copyrights on modified files
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>