- 03 Dec, 2007 8 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6Linus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits) LIB82596: correct data types for hardware addresses via-velocity: don't oops on MTU change (resend) Stop phy code from returning success to unknown ioctls. SET_NETDEV_DEV() in fec_mpc52xx.c net: smc911x: only enable for mpr2 on sh. e1000: Fix NAPI state bug when Rx complete sky2: turn of dynamic Tx watermark workaround (FE+ only) sky2: don't use AER routines sky2: revert to access PCI config via device space cxgb - fix stats cxgb - fix NAPI cxgb - fix T2 GSO ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters phylib: marvell: add support for TX-only and RX-only Internal Delay phylib: add PHY interface modes for internal delay for tx and rx only skge: MTU changing fix skge: serial mode register values skge version 1.13 skge: increase TX threshold for Jumbo skge: fiber link up/down fix ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-devLinus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: sata_mv: Fix broken Marvell 7042 support. libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19)) ata_piix: add more toshiba laptops to broken suspend list libata: More IVB horkage from TSST libata: report protocol and full CDB on error Several fixes for the AVR32 PATA driver sata_mv: fix compilation error when enabling DEBUG Set proper ATA UDMA mode for bf548 according to system clock.
-
Vivek Goyal authored
Signed-off-by:
Vivek Goyal <vgoyal@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Jeff Dike authored
Under the conditions that UML uses it, tcgetattr is guaranteed to return -EINTR when the console is attached to /dev/ptmx, making generic_console_write hang because it loops, calling tcgetattr until it succeeds. This is a host bug - see http://marc.info/?l=linux-kernel&m=119618990807182&w=2 for the details. This patch works around it by blocking SIGIO while the terminal attributes are being fiddled. Signed-off-by:
Jeff Dike <jdike@linux.intel.com> Signed-off-by:
-
Jeff Dike authored
I forgot to have an int-returning function actually return something. Signed-off-by:
-
Al Viro authored
The previous commit ("uml: keep UML Kconfig in sync with x86") is not enough, unfortunately. If we go that way, we need to add dependencies on !UML for several options. Signed-off-by:Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Jeff Dike authored
Fix a UML build breakage introduced by commit 1032c0ba - it introduces X86_32, with many things which UML needs depending on it. This patch adds definitions of X86_32 and RWSEM_XCHGADD_ALGORITHM to the UML/i386 Kconfig. Signed-off-by:
-
Karsten Keil authored
Fix possible memory overrun issue in the isdn ioctl code. Found by ADLAB <adlab@venustech.com.cn> Signed-off-by:
Karsten Keil <kkeil@suse.de> Cc: ADLAB <adlab@venustech.com.cn> Cc: <stable@kernel.org> Signed-off-by:
-
- 01 Dec, 2007 32 commits
-
-
Mark Lord authored
sata_mv: Fix broken Marvell 7042 support. The Marvell 7042 chip is more or less the same as the 6042 internally, but sports a PCIe bus. Despite having identical SATA cores, the 7042 does differ from its PCI bus counterparts in placment and layout of certain bus related registers. This patch fixes sata_mv to distinguish between the PCI bus registers of earlier chips, and the PCIe bus registers of the 7042. Specifically, move the offsets and bit patterns for the PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv, as these values differ between the 6xxx and 7xxx series chips. This fixes the driver to not access reserved PCI addresses, and prevents the lockups reported in linux-2.6.24 with 7042 boards. Also add a new PCI ID for the Highpoint 2300 7042-based board that I'm using for testing this stuff here. Tested with Marvell 6081 + 7042 chips, on x86 & x86_64. Signed-off-by:
Mark Lord <mlord@pobox.com> Signed-off-by:
Jeff Garzik <jeff@garzik.org>
-
Alan Cox authored
On Fri, 30 Nov 2007 14:34:11 +0200 (EET) Meelis Roos <mroos@linux.ee> wrote: > > Can you stick a stack trace in at that point ? That would help diagnose > > it a great deal quicker. > > Finally done - found out hard way that BUG() is too bad and > dump_st5ack() suits me better. Thanks. This should fix the real cause, and also allow for port start to fail politely with -ENODEV. Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
Peter Schwenke authored
Add more toshiba laptops to broken suspend list. This is from OSDL bugzilla bug 7780. tj: re-formatted patch and added description and SOB. Signed-off-by:
Peter Schwenke <peter@bluetoad.com.au> Signed-off-by:
Tejun Heo <htejun@gmail.com> Signed-off-by:
-
Peter Missel authored
libata: Add more TSST (Samsung/Toshiba) IDE drives with broken cable detection validation bits. signed-off-by: Peter Missel (peter.missel@onlinehome.de) Acked-by:
-
Tejun Heo authored
Protocol and CDB allocation size field are important in determining what went wrong with ATAPI commands. Report them on failure. Signed-off-by:
-
Kristoffer Nyborg Gregertsen authored
Several fixes for the AVR32 PATA driver: * Updated to use new AVR32 SMC timing API. This removes the need for "magic" constants in signal timing. * Removed the ATA_FLAG_PIO_POLLING, the driver should use interrupts. * Removed .port_disable and .irq_ack as these are no longer needed. * Improved some comments. Signed-off-by:
Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com> Signed-off-by:
-
Saeed Bishara authored
use sstatus instead status. Signed-off-by:
Saeed Bishara <saeed@marvell.com> Signed-off-by:
-
sonic zhang authored
UDMA Mode - Frequency compatibility UDMA5 - 100 MB/s - SCLK = 133 MHz UDMA4 - 66 MB/s - SCLK >= 80 MHz UDMA3 - 44.4 MB/s - SCLK >= 50 MHz UDMA2 - 33 MB/s - SCLK >= 40 MHz Signed-off-by:
Sonic Zhang <sonic.zhang@analog.com> Signed-off-by:
-
Thomas Bogendoerfer authored
dma_addr_t is 64bit wide on some architectures (for example 64bit MIPS), so it's not a good idea to use it for 32bit wide addresses in descriptors. Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by:
-
Stephen Hemminger authored
The VIA veloicty driver needs the following to allow changing MTU when down. The buffer size needs to be computed when device is brought up, not when device is initialized. This also fixes a bug where the buffer size was computed differently on change_mtu versus initial setting. Signed-off-by:
Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by:
-
David Woodhouse authored
This kind of sucks, and prevents the Fedora installer from using the device for network installs... [root@efika phy]# iwconfig eth0 Warning: Driver for device eth0 has been compiled with an ancient version of Wireless Extension, while this program support version 11 and later. Some things may be broken... eth0 ESSID:off/any Nickname:"" NWID:0 Channel:0 Access Point: 00:00:BF:81:14:E0 Bit Rate:-1.08206e+06 kb/s Sensitivity=0/0 RTS thr:off Fragment thr:off Encryption key:<too big> Power Management:off Signed-off-by:David Woodhouse <dwmw2@infradead.org> Signed-off-by:
-
David Woodhouse authored
This helps to allow the Fedora installer to use the built-in Ethernet on the Efika for a network install. Signed-off-by:
-
Paul Mundt authored
The smc911x.h is a bit of a mess, not supporting any sort of generic configuration. For the moment only ARCH_PXA and SH_MAGIC_PANEL_R2 have suitable definitions, so we reflect this in the Kconfig also. While there are other SH boards that will likely turn this on in the 2.6.25 time frame, it's not worth trying to stub around at the moment. Fixes up the allmodconfig build, as noted by akpm. Signed-off-by:
Paul Mundt <lethal@linux-sh.org> Signed-off-by:
-
Auke Kok authored
Don't exit polling when we have not yet used our budget, this causes the NAPI system to end up with a messed up poll list. Signed-off-by:
Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by:
-
Stephen Hemminger authored
Add workaround for issues FE+ (A0) transmit watermark. This is copied verbatim from vendor driver sk98lin (10.22.4.3). Don't have that chip version and no more information seems to be available. Signed-off-by:
-
Stephen Hemminger authored
Using PCIE advanced error recovery stuff creates more user problems than it's worth. The AER stuff depends on MMCONFIG and in many configurations it just doesn't work. Plus it doesn't add any real functionality to the driver. The sky2 driver handles its own errors fine as is. This reverts 555382cbSigned-off-by:
-
Stephen Hemminger authored
Using the hardware window into PCI config space is more reliable and smaller/faster than using the pci_config routines. It avoids issues with MMCONFIG etc. Reverts: 167f53d0 Please apply for 2.6.24 Signed-off-by:
-
Divy Le Ray authored
Fix MAC stats accounting. Fix get_stats. Signed-off-by:
Divy Le Ray <divy@chelsio.com> Signed-off-by:
-
Divy Le Ray authored
netif_rx_complete() should be called only when work_done < budget. Signed-off-by:
-
Divy Le Ray authored
The patch ensures that a GSO skb has enough headroom to push an encapsulating cpl_tx_pkt_lso header. Signed-off-by:
-
Kim Phillips authored
Extend the RGMII-Internal Delay specification case to include TX-only and RX-only variants. Signed-off-by:
Kim Phillips <kim.phillips@freescale.com> Tested-by:
Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by:
Li Yang <leoli@freescale.com> Signed-off-by:
-
Kim Phillips authored
Previously, Internal Delay specification implied the delay be applied to both TX and RX. This patch allows for separate TX/RX-only internal delay specification. Signed-off-by:
-
Kim Phillips authored
Allow phylib specification of cases where hardware needs to configure PHYs for Internal Delay only on either RX or TX (not both). Signed-off-by:
-
Stephen Hemminger authored
The code to change MTU doesn't correctly handle all the chip variations and requirements for restarting. On Genesis chips changing MTU would just cause receiver to hang. Use a simpler approach of just taking link down/up if needed. Signed-off-by:
-
Stephen Hemminger authored
For compatiablity with sk98lin, make sure and set same values in serial mode register. Signed-off-by:
-
Stephen Hemminger authored
Version for 2.6.24 Signed-off-by:
-
Stephen Hemminger authored
Need to increase TX threshold when doing Jumbo frames on dual port board to avoid underruns. (Code from sk98lin). Signed-off-by:
-
Stephen Hemminger authored
The driver would not work over fibre if other end when down then came back up (would require reloading driver). The correct way to manage the link the same way for both TP and fibre. Resloves problem described in: http://lkml.org/lkml/2007/11/6/395Signed-off-by:
-
Stephen Hemminger authored
Make sure and retry when shutting down the MAC. This code is copied from sk98lin driver. Signed-off-by:
-
Stephen Hemminger authored
Receive FIFO overrun is not catastrophic condition, so don't flush when it happens. Signed-off-by:
-
Stephen Hemminger authored
The calculation of usable FIFO RAM is wrong in the skge driver. First, is doesn't take into account the reserved area on the original SysKonnect Genesis boards. Second it has an off-by-one error because hw->ports is either 1 or 2. Signed-off-by:
-
Peter Tiedemann authored
Currently ctc-device initialization is broken (kernel bug in ctc_new_device). The new network namespace code reveals a deficiency of the ctc driver. It should make use of alloc_netdev() as described in Documentation/networking/netdevices.txt. Signed-off-by:
Peter Tiedemann <ptiedem@de.ibm.com> Signed-off-by:
Ursula Braun <braunu@de.ibm.com> Signed-off-by:
-
