For sinks that do not support audio, there is no need to notify
audio subsystem of the connection event.

This will make sure that audio routes only to the primary display
when connected to such sinks.

changes in v2:
  - Added fixes tag
  - Removed nested if condition and removed usage of global pointer

Fixes: d13e36d7 ("drm/msm/dp: add audio support for Display Port on MSM")
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Some dongles require link training done at irq_hpd request instead
of plugin request. This patch promote irq_hpd handler to handle link
training and setup hpd_state correctly.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Some dongle will not clear LINK_STATUS_UPDATED bit after
DPCD read which cause link training failed. This patch
just read 6 bytes of DPCD link status from sink and return
without checking LINK_STATUS_UPDATED bit.
Only 8 bits are used to represent link rate at sinker DPCD.
The really link rate is 2.7Mb times the 8 bits value.
For example, 0x0A at DPCD is equal to 2.7Gb (10 * 2.7Mb).
This patch also convert 8 bits value of DPCD to really link
rate to fix worng link rate error during phy compliance test.

Fixes: 6625e263 ("drm/msm/dp: DisplayPort PHY compliance tests fixup")
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

DP compo phy have to be enable to start link training. When
link training failed phy need to be disabled so that next
link traning can be proceed smoothly at next plug in. This
patch de-initialize mainlink to disable phy if link training
failed. This prevent system crash due to
disp_cc_mdss_dp_link_intf_clk stuck at "off" state.  This patch
also perform checking power_on flag at dp_display_enable() and
dp_display_disable() to avoid crashing when unplug cable while
display is off.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Connection state is not set correctly happen when either failure of link
train due to cable unplugged in the middle of aux channel reading or
cable plugged in while in suspended state. This patch fixes these problems.
This patch also replace ST_SUSPEND_PENDING with ST_DISPLAY_OFF.

Changes in V2:
-- Add more information to commit message.

Changes in V3:
-- change base

Changes in V4:
-- add Fixes tag
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

During suspend, dp host controller and hpd block are disabled due to
both ahb and aux clock are disabled. Therefore hpd plug/unplug interrupts
will not be generated. At dp_pm_resume(), reinitialize both dp host
controller and hpd block so that hpd plug/unplug interrupts will be
generated and handled by driver so that hpd connection state is updated
correctly. This patch will fix link training flaky issues.

Changes in v2:
-- use container_of to cast correct dp_display_private pointer
   at both dp_pm_suspend() and dp_pm_resume().

Changes in v3:
-- replace hpd_state atomic_t  with u32

Changes in v4
-- call dp_display_host_deinit() at dp_pm_suspend()
-- call dp_display_host_init() at msm_dp_display_enable()
-- fix phy->init_count unbalance which causes link training failed

Changes in v5
--  add Fixes tag

Fixes:  8ede2ecc (drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets)
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Similar to the previous patch, clear shadow on suspend to avoid timeouts
waiting for ringbuffer space.

Fixes: 8907afb4 ("drm/msm: Allow a5xx to mark the RPTR shadow as privileged")
Signed-off-by: Rob Clark <robdclark@chromium.org>

Clear the shadow rptr on suspend.  Otherwise, when we resume, we can
have a stale value until CP_WHERE_AM_I executes.  If we suspend near
the ringbuffer wraparound point, this can lead to a chicken/egg
situation where we are waiting for ringbuffer space to write the
CP_WHERE_AM_I (or CP_INIT) packet, because we mistakenly believe that
the ringbuffer is full (due to stale rptr value in the shadow).

Fixes errors like:

  [drm:adreno_wait_ring [msm]] *ERROR* timeout waiting for space in ringbuffer 0

in the resume path.

Fixes: d3a569fc ("drm/msm: a6xx: Use WHERE_AM_I for eligible targets")
Signed-off-by: Rob Clark <robdclark@chromium.org>

Add cooling device support to gpu. A cooling device is bound to a
thermal zone to allow thermal mitigation.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Register GPU as a devfreq cooling device so that it can be passively
cooled by the thermal framework.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Now that the inactive_list is protected by mm_lock, and everything
else on per-obj basis is protected by obj->resv, we no longer depend
on struct_mutex.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The obj->lock is sufficient for what we need.

This *does* have the implication that userspace can try to shoot
themselves in the foot by racing madvise(DONTNEED) with submit.  But
the result will be about the same if they did madvise(DONTNEED) before
the submit ioctl, ie. they might not get want they want if they race
with shrinker.  But iova fault handling is robust enough, so userspace
is only shooting it's own foot.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Now that we don't need struct_mutex in the free path, we can get rid of
the asynchronous free altogether.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Now that active_list/inactive_list is protected by mm_lock, we no longer
need dev->struct_mutex in the free_object() path.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Now that we are not relying on dev->struct_mutex to protect the
ring->submits lists, drop the struct_mutex lock.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

It cannot be atomically updated with obj->active_count, and the only
purpose is a useless WARN_ON() (which becomes a buggy WARN_ON() once
retire_submits() is not serialized with incoming submits via
struct_mutex)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Before we remove dev->struct_mutex from the retire path, we have to deal
with the situation of a submit retiring before the submit ioctl returns.

To deal with this, ring->submits will hold a reference to the submit,
which is dropped when the submit is retired.  And the submit ioctl path
holds it's own ref, which it drops when it is done with the submit.

Also, add to submit list *after* getting/pinning bo's, to prevent badness
in case the completed fence is corrupted, and retire_worker mistakenly
believes the submit is done too early.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

One less place to rely on dev->struct_mutex.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Before adding another lock, give ring->lock a more descriptive name.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Rather than relying on the big dev->struct_mutex hammer, introduce a
more specific lock for protecting the bo lists.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Small cleanup, update_fences() is used in the hangcheck path, but also
in the normal retire path.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

It is somewhat redundant with the gpu tracepoints, and anyways not too
useful to justify spamming the log when debug traces are enabled.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

We only want to use the _unlocked() variant in the unlocked case.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

This also converts the special msm_gem_get_vaddr_active() to expect the
lock to already be held.  There are two call-sites for this, one already
has the lock held, so it is more straightforward to just open-code the
locking for the other caller.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Unfortunately, due to an dev_pm_opp locking interaction with
mm->mmap_sem, we need to do pm get before aquiring obj locks,
otherwise we can have anger lockdep with the chain:

  opp_table_lock --> &mm->mmap_sem --> reservation_ww_class_mutex

For an explicit fencing userspace, the impact should be minimal
as we do all the fence waits before this point.  It could result
in some needless resumes in error cases, etc.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

We cannot switch to using obj->resv for locking without first moving all
the copy_from_user() ahead of submit_lock_objects().  Otherwise in the
mm fault path we aquire mm->mmap_sem before obj lock, but in the submit
path the order is reversed.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Move grabbing the bo lock into shrinker, with a msm_gem_trylock() to
skip over bo's that are already locked.  This gets rid of the nested
lock classes.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

When we cut-over to using dma_resv_lock/etc instead of msm_obj->lock,
we'll need these for the submit path (where resv->lock is already held).
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

We'll need to introduce a _locked() version of msm_gem_get_iova(), so we
need to make that name available.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

This will make it easier to transition over to obj->resv locking for
everything that is per-bo locking.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The microcode bo's should never be madvise(WONTNEED), so these should
not be using msm_gem_get_vaddr_active().
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Reading VCO rate for this PLL can cause boot stalls, if it is not
enabled. Guard clk_hw_get_rate with a call to
dsi_pll_28nm_clk_is_enabled().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The dev_pm_opp_of_add_table() api initializes the icc nodes for gpu
indirectly. So we can avoid using of_icc_get() api in the common
probe path. To improve this, move of_icc_get() to target specific code
where it is required.

This patch helps to fix duplicate gpu node listed in the interconnect
summary from the debugfs.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

c33b7c03 ("drm/msm/dpu: add support for clk and bw scaling for
display") has added support for handling bandwidth voting in kms path in
addition to old mdss path. However this broke all other platforms since
_dpu_core_perf_crtc_update_bus() will now error out instead of properly
calculating bandwidth and core clocks. Fix
_dpu_core_perf_crtc_update_bus() to just skip bandwidth setting instead
of returning an error in case kms->num_paths == 0 (MDSS is used for
bandwidth management).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c33b7c03 ("drm/msm/dpu: add support for clk and bw scaling for display")
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Handle new merge_3d block setup in dpu encoder code. Pass correct mode
and id. Note, that merge_3d blocks are not handled via usual RM
reservation mechanism, as each merge_3d block is tied to two PPs, so by
reserving PP you get merge_3d automatically.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Handle setting up merge mode in merge_3d hardware block.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Active HW CTL blocks need separate handling for merge_3d flushes.
Implement necessary merge_3d configuration and flushing.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Add initial support for merge3D hardware block on SM8[12]50. Merge3D is
reposible for merging contents of two LMs (two PPs) into single
interface.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Instead of calling 4 callbacks to set pending masks, call just one to
update both pending_flush_mask and pending_intf_flush mask. Note, that
CMD mode support incorrectly did not update pending_intf_flush mask,
breaking CMD support on SC7180/SM8x50.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>