- 17 Jul, 2023 3 commits
-
-
Victor Nogueira authored
In the case of an update, when TCA_U32_LINK is set, u32_set_parms will decrement the refcount of the ht_down (struct tc_u_hnode) pointer present in the older u32 filter which we are replacing. However, if u32_replace_hw_knode errors out, the update command fails and that ht_down pointer continues decremented. To fix that, when u32_replace_hw_knode fails, check if ht_down's refcount was decremented and undo the decrement. Fixes: d34e3e18 ("net: cls_u32: Add support for skip-sw flag to tc u32 classifier.") Signed-off-by:
Victor Nogueira <victor@mojatatu.com> Acked-by:
Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by:
Pedro Tammela <pctammela@mojatatu.com> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Victor Nogueira authored
When u32_replace_hw_knode fails, we need to undo the tcf_bind_filter operation done at u32_set_parms. Fixes: d34e3e18 ("net: cls_u32: Add support for skip-sw flag to tc u32 classifier.") Signed-off-by:
-
Victor Nogueira authored
In case an error occurred after mall_set_parms executed successfully, we must undo the tcf_bind_filter call it issues. Fix that by calling tcf_unbind_filter in err_replace_hw_filter label. Fixes: ec2507d2 ("net/sched: cls_matchall: Fix error path") Signed-off-by:
-
- 15 Jul, 2023 10 commits
-
-
Jakub Kicinski authored
Randy Dunlap says: ==================== net: fix kernel-doc problems in include/net/ Fix many (but not all) kernel-doc warnings in include/net/. [PATCH v2 net 1/9] net: bonding: remove kernel-doc comment marker [PATCH v2 net 2/9] net: cfg802154: fix kernel-doc notation warnings [PATCH v2 net 3/9] codel: fix kernel-doc notation warnings [PATCH v2 net 4/9] devlink: fix kernel-doc notation warnings [PATCH v2 net 5/9] inet: frags: remove kernel-doc comment marker [PATCH v2 net 6/9] net: llc: fix kernel-doc notation warnings [PATCH v2 net 7/9] net: NSH: fix kernel-doc notation warning [PATCH v2 net 8/9] pie: fix kernel-doc notation warning [PATCH v2 net 9/9] rsi: remove kernel-doc comment marker ==================== Link: https://lore.kernel.org/r/20230714045127.18752-1-rdunlap@infradead.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Randy Dunlap authored
Change an errant kernel-doc comment marker (/**) to a regular comment to prevent a kernel-doc warning. rsi_91x.h:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst * Copyright (c) 2017 Redpine Signals Inc. Fixes: 4c10d56a ("rsi: add header file rsi_91x") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Cc: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Acked-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230714045127.18752-10-rdunlap@infradead.orgSigned-off-by:
-
Randy Dunlap authored
Spell a struct member's name correctly to prevent a kernel-doc warning. pie.h:38: warning: Function parameter or member 'tupdate' not described in 'pie_params' Fixes: b42a3d7c ("pie: improve comments and commenting style") Signed-off-by:
-
Randy Dunlap authored
Use the struct member's name and the correct format to prevent a kernel-doc warning. nsh.h:200: warning: Function parameter or member 'context' not described in 'nsh_md1_ctx' Fixes: 1f0b7744 ("net: add NSH header structures and helpers") Signed-off-by:
-
Randy Dunlap authored
Use the corrent function parameter name or format to prevent kernel-doc warnings. Add 2 function parameter descriptions to prevent kernel-doc warnings. llc_pdu.h:278: warning: Function parameter or member 'da' not described in 'llc_pdu_decode_da' llc_pdu.h:278: warning: Excess function parameter 'sa' description in 'llc_pdu_decode_da' llc_pdu.h:330: warning: Function parameter or member 'skb' not described in 'llc_pdu_init_as_test_cmd' llc_pdu.h:379: warning: Function parameter or member 'svcs_supported' not described in 'llc_pdu_init_as_xid_cmd' llc_pdu.h:379: warning: Function parameter or member 'rx_window' not described in 'llc_pdu_init_as_xid_cmd' Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Randy Dunlap authored
Modify the anonymous enum kernel-doc content so that it doesn't cause a kernel-doc warning. inet_frag.h:33: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst Fixes: 1ab1934e ("inet: frags: enum the flag definitions and add descriptions") Signed-off-by:
-
Randy Dunlap authored
Spell function or struct member names correctly. Use ':' instead of '-' for struct member entries. Mark one field as private in kernel-doc. Add a few entries that were missing. Fix a typo. These changes prevent kernel-doc warnings: devlink.h:252: warning: Function parameter or member 'field_id' not described in 'devlink_dpipe_match' devlink.h:267: warning: Function parameter or member 'field_id' not described in 'devlink_dpipe_action' devlink.h:310: warning: Function parameter or member 'match_values_count' not described in 'devlink_dpipe_entry' devlink.h:355: warning: Function parameter or member 'list' not described in 'devlink_dpipe_table' devlink.h:374: warning: Function parameter or member 'actions_dump' not described in 'devlink_dpipe_table_ops' devlink.h:374: warning: Function parameter or member 'matches_dump' not described in 'devlink_dpipe_table_ops' devlink.h:374: warning: Function parameter or member 'entries_dump' not described in 'devlink_dpipe_table_ops' devlink.h:374: warning: Function parameter or member 'counters_set_update' not described in 'devlink_dpipe_table_ops' devlink.h:374: warning: Function parameter or member 'size_get' not described in 'devlink_dpipe_table_ops' devlink.h:384: warning: Function parameter or member 'headers' not described in 'devlink_dpipe_headers' devlink.h:384: warning: Function parameter or member 'headers_count' not described in 'devlink_dpipe_headers' devlink.h:398: warning: Function parameter or member 'unit' not described in 'devlink_resource_size_params' devlink.h:487: warning: Function parameter or member 'id' not described in 'devlink_param' devlink.h:645: warning: Function parameter or member 'overwrite_mask' not described in 'devlink_flash_update_params' Fixes: 1555d204 ("devlink: Support for pipeline debug (dpipe)") Fixes: d9f9b9a4 ("devlink: Add support for resource abstraction") Fixes: eabaef18 ("devlink: Add devlink_param register and unregister") Fixes: 5d5b4128 ("devlink: introduce flash update overwrite mask") Signed-off-by:
-
Randy Dunlap authored
Use '@' before the struct member names in kernel-doc notation to prevent kernel-doc warnings. codel.h:158: warning: Function parameter or member 'ecn_mark' not described in 'codel_stats' codel.h:158: warning: Function parameter or member 'ce_mark' not described in 'codel_stats' Fixes: 76e3cc12 ("codel: Controlled Delay AQM") Signed-off-by:
-
Randy Dunlap authored
Add an enum heading to the kernel-doc comments to prevent kernel-doc warnings. cfg802154.h:174: warning: Cannot understand * @WPAN_PHY_FLAG_TRANSMIT_POWER: Indicates that transceiver will support on line 174 - I thought it was a doc line cfg802154.h:192: warning: Enum value 'WPAN_PHY_FLAG_TXPOWER' not described in enum 'wpan_phy_flags' cfg802154.h:192: warning: Excess enum value 'WPAN_PHY_FLAG_TRANSMIT_POWER' description in 'wpan_phy_flags' Fixes: edea8f7c ("cfg802154: introduce wpan phy flags") Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20230714045127.18752-3-rdunlap@infradead.orgSigned-off-by:
-
Randy Dunlap authored
Change an errant kernel-doc comment marker (/**) to a regular comment to prevent a kernel-doc warning. bonding.h:282: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst * Returns NULL if the net_device does not belong to any of the bond's slaves Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
- 14 Jul, 2023 9 commits
-
-
Yan Zhai authored
Commit 1fd54773 ("udp: allow header check for dodgy GSO_UDP_L4 packets.") checks DODGY bit for UDP, but for packets that can be fed directly to the device after gso_segs reset, it actually falls through to fragmentation: https://lore.kernel.org/all/CAJPywTKDdjtwkLVUW6LRA2FU912qcDmQOQGt2WaDo28KzYDg+A@mail.gmail.com/ This change restores the expected behavior of GSO_UDP_L4 packets. Fixes: 1fd54773 ("udp: allow header check for dodgy GSO_UDP_L4 packets.") Suggested-by:
Willem de Bruijn <willemdebruijn.kernel@gmail.com> Signed-off-by:
Yan Zhai <yan@cloudflare.com> Reviewed-by:
Willem de Bruijn <willemb@google.com> Acked-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Wang Ming authored
Identify issues that arise by using the tests/doublebitand.cocci semantic patch. Need to remove duplicate expression in if statement. Signed-off-by:
Wang Ming <machel@vivo.com> Reviewed-by:
Jiawen Wu <jiawenwu@trustnetic.com> Signed-off-by:
-
Wang Ming authored
It is expected that most callers should _ignore_ the errors return by debugfs_create_dir() in bnad_debugfs_init(). Signed-off-by:
-
Daniel Golle authored
Move the call to of_get_ethdev_address to mtk_add_mac which is part of the probe function and can hence itself return -EPROBE_DEFER should of_get_ethdev_address return -EPROBE_DEFER. This allows us to entirely get rid of the mtk_init function. The problem of of_get_ethdev_address returning -EPROBE_DEFER surfaced in situations in which the NVMEM provider holding the MAC address has not yet be loaded at the time mtk_eth_soc is initially probed. In this case probing of mtk_eth_soc should be deferred instead of falling back to use a random MAC address, so once the NVMEM provider becomes available probing can be repeated. Fixes: 656e7052 ("net-next: mediatek: add support for MT7623 ethernet") Signed-off-by:
Daniel Golle <daniel@makrotopia.org> Signed-off-by:
-
Kuniyuki Iwashima authored
When we create an L2 loop on a bridge in netns, we will see packets storm even if STP is enabled. # unshare -n # ip link add br0 type bridge # ip link add veth0 type veth peer name veth1 # ip link set veth0 master br0 up # ip link set veth1 master br0 up # ip link set br0 type bridge stp_state 1 # ip link set br0 up # sleep 30 # ip -s link show br0 2: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000 link/ether b6:61:98:1c:1c:b5 brd ff:ff:ff:ff:ff:ff RX: bytes packets errors dropped missed mcast 956553768 12861249 0 0 0 12861249 <-. Keep TX: bytes packets errors dropped carrier collsns | increasing 1027834 11951 0 0 0 0 <-' rapidly This is because llc_rcv() drops all packets in non-root netns and BPDU is dropped. Let's add extack warning when enabling STP in netns. # unshare -n # ip link add br0 type bridge # ip link set br0 type bridge stp_state 1 Warning: bridge: STP does not work in non-root netns. Note this commit will be reverted later when we namespacify the whole LLC infra. Fixes: e730c155 ("[NET]: Make packet reception network namespace safe") Suggested-by:Harry Coin <hcoin@quietfountain.com> Link: https://lore.kernel.org/netdev/0f531295-e289-022d-5add-5ceffa0df9bc@quietfountain.com/Suggested-by:
Ido Schimmel <idosch@idosch.org> Signed-off-by:
Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by:
Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
-
Tanmay Patil authored
CPSW ALE has 75 bit ALE entries which are stored within three 32 bit words. The cpsw_ale_get_field() and cpsw_ale_set_field() functions assume that the field will be strictly contained within one word. However, this is not guaranteed to be the case and it is possible for ALE field entries to span across up to two words at the most. Fix the methods to handle getting/setting fields spanning up to two words. Fixes: db82173f ("netdev: driver: ethernet: add cpsw address lookup engine support") Signed-off-by:
Tanmay Patil <t-patil@ti.com> [s-vadapalli@ti.com: rephrased commit message and added Fixes tag] Signed-off-by:
Siddharth Vadapalli <s-vadapalli@ti.com> Signed-off-by:
-
Mark Brown authored
The at9331 is only able to read or write a single register at once. The driver has a custom regmap bus and chooses to tell the regmap core about this by reporting the maximum transfer sizes rather than the explicit flags that exist at the regmap level. Since there are a number of problems with the raw transfer limits and the regmap level flags are better integrated anyway convert the driver to use the flags. No functional change. Signed-off-by:
Mark Brown <broonie@kernel.org> Reviewed-by:
-
Alan Stern authored
The syzbot fuzzer identified a problem in the usbnet driver: usb 1-1: BOGUS urb xfer, pipe 3 != type 1 WARNING: CPU: 0 PID: 754 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 Modules linked in: CPU: 0 PID: 754 Comm: kworker/0:2 Not tainted 6.4.0-rc7-syzkaller-00014-g692b7dc8 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023 Workqueue: mld mld_ifc_work RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 Code: 7c 24 18 e8 2c b4 5b fb 48 8b 7c 24 18 e8 42 07 f0 fe 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 a0 c9 fc 8a e8 5a 6f 23 fb <0f> 0b e9 58 f8 ff ff e8 fe b3 5b fb 48 81 c5 c0 05 00 00 e9 84 f7 RSP: 0018:ffffc9000463f568 EFLAGS: 00010086 RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000 RDX: ffff88801eb28000 RSI: ffffffff814c03b7 RDI: 0000000000000001 RBP: ffff8881443b7190 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000003 R13: ffff88802a77cb18 R14: 0000000000000003 R15: ffff888018262500 FS: 0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000556a99c15a18 CR3: 0000000028c71000 CR4: 0000000000350ef0 Call Trace: <TASK> usbnet_start_xmit+0xfe5/0x2190 drivers/net/usb/usbnet.c:1453 __netdev_start_xmit include/linux/netdevice.h:4918 [inline] netdev_start_xmit include/linux/netdevice.h:4932 [inline] xmit_one net/core/dev.c:3578 [inline] dev_hard_start_xmit+0x187/0x700 net/core/dev.c:3594 ... This bug is caused by the fact that usbnet trusts the bulk endpoint addresses its probe routine receives in the driver_info structure, and it does not check to see that these endpoints actually exist and have the expected type and directions. The fix is simply to add such a check. Reported-and-tested-by: syzbot+63ee658b9a100ffadbe2@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-usb/000000000000a56e9105d0cec021@google.com/Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> CC: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/ea152b6d-44df-4f8a-95c6-4db51143dcc1@rowland.harvard.eduSigned-off-by:
-
Linus Walleij authored
I get sporadic timeouts from the driver when using the MV88E6352. Reading the status again after the loop fixes the problem: the operation is successful but goes undetected. Some added prints show things like this: [ 58.356209] mv88e6085 mdio_mux-0.1:00: Timeout while waiting for switch, addr 1b reg 0b, mask 8000, val 0000, data c000 [ 58.367487] mv88e6085 mdio_mux-0.1:00: Timeout waiting for ATU op 4000, fid 0001 (...) [ 61.826293] mv88e6085 mdio_mux-0.1:00: Timeout while waiting for switch, addr 1c reg 18, mask 8000, val 0000, data 9860 [ 61.837560] mv88e6085 mdio_mux-0.1:00: Timeout waiting for PHY command 1860 to complete The reason is probably not the commands: I think those are mostly fine with the 50+50ms timeout, but the problem appears when OpenWrt brings up several interfaces in parallel on a system with 7 populated ports: if one of them take more than 50 ms and waits one or more of the others can get stuck on the mutex for the switch and then this can easily multiply. As we sleep and wait, the function loop needs a final check after exiting the loop if we were successful. Suggested-by:Andrew Lunn <andrew@lunn.ch> Cc: Tobias Waldekranz <tobias@waldekranz.com> Fixes: 35da1dfd ("net: dsa: mv88e6xxx: Improve performance of busy bit polling") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
-
- 13 Jul, 2023 17 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Paolo Abeni: "Including fixes from netfilter, wireless and ebpf. Current release - regressions: - netfilter: conntrack: gre: don't set assured flag for clash entries - wifi: iwlwifi: remove 'use_tfh' config to fix crash Previous releases - regressions: - ipv6: fix a potential refcount underflow for idev - icmp6: ifix null-ptr-deref of ip6_null_entry->rt6i_idev in icmp6_dev() - bpf: fix max stack depth check for async callbacks - eth: mlx5e: - check for NOT_READY flag state after locking - fix page_pool page fragment tracking for XDP - eth: igc: - fix tx hang issue when QBV gate is closed - fix corner cases for TSN offload - eth: octeontx2-af: Move validation of ptp pointer before its usage - eth: ena: fix shift-out-of-bounds in exponential backoff Previous releases - always broken: - core: prevent skb corruption on frag list segmentation - sched: - cls_fw: fix improper refcount update leads to use-after-free - sch_qfq: account for stab overhead in qfq_enqueue - netfilter: - report use refcount overflow - prevent OOB access in nft_byteorder_eval - wifi: mt7921e: fix init command fail with enabled device - eth: ocelot: fix oversize frame dropping for preemptible TCs - eth: fec: recycle pages for transmitted XDP frames" * tag 'net-6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (79 commits) selftests: tc-testing: add test for qfq with stab overhead net/sched: sch_qfq: account for stab overhead in qfq_enqueue selftests: tc-testing: add tests for qfq mtu sanity check net/sched: sch_qfq: reintroduce lmax bound check for MTU wifi: cfg80211: fix receiving mesh packets without RFC1042 header wifi: rtw89: debug: fix error code in rtw89_debug_priv_send_h2c_set() net: txgbe: fix eeprom calculation error net/sched: make psched_mtu() RTNL-less safe net: ena: fix shift-out-of-bounds in exponential backoff netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write() net/sched: flower: Ensure both minimum and maximum ports are specified MAINTAINERS: Add another mailing list for QUALCOMM ETHQOS ETHERNET DRIVER docs: netdev: update the URL of the status page wifi: iwlwifi: remove 'use_tfh' config to fix crash xdp: use trusted arguments in XDP hints kfuncs bpf: cpumap: Fix memory leak in cpu_map_update_elem wifi: airo: avoid uninitialized warning in airo_get_rate() octeontx2-pf: Add additional check for MCAM rules net: dsa: Removed unneeded of_node_put in felix_parse_ports_node net: fec: use netdev_err_once() instead of netdev_err() ... -
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-traceLinus Torvalds authored
Pull tracing fixes from Steven Rostedt: - Fix some missing-prototype warnings - Fix user events struct args (did not include size of struct) When creating a user event, the "struct" keyword is to denote that the size of the field will be passed in. But the parsing failed to handle this case. - Add selftest to struct sizes for user events - Fix sample code for direct trampolines. The sample code for direct trampolines attached to handle_mm_fault(). But the prototype changed and the direct trampoline sample code was not updated. Direct trampolines needs to have the arguments correct otherwise it can fail or crash the system. - Remove unused ftrace_regs_caller_ret() prototype. - Quiet false positive of FORTIFY_SOURCE Due to backward compatibility, the structure used to save stack traces in the kernel had a fixed size of 8. This structure is exported to user space via the tracing format file. A change was made to allow more than 8 functions to be recorded, and user space now uses the size field to know how many functions are actually in the stack. But the structure still has size of 8 (even though it points into the ring buffer that has the required amount allocated to hold a full stack. This was fine until the fortifier noticed that the memcpy(&entry->caller, stack, size) was greater than the 8 functions and would complain at runtime about it. Hide this by using a pointer to the stack location on the ring buffer instead of using the address of the entry structure caller field. - Fix a deadloop in reading trace_pipe that was caused by a mismatch between ring_buffer_empty() returning false which then asked to read the data, but the read code uses rb_num_of_entries() that returned zero, and causing a infinite "retry". - Fix a warning caused by not using all pages allocated to store ftrace functions, where this can happen if the linker inserts a bunch of "NULL" entries, causing the accounting of how many pages needed to be off. - Fix histogram synthetic event crashing when the start event is removed and the end event is still using a variable from it - Fix memory leak in freeing iter->temp in tracing_release_pipe() * tag 'trace-v6.5-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: tracing: Fix memory leak of iter->temp when reading trace_pipe tracing/histograms: Add histograms to hist_vars if they have referenced variables tracing: Stop FORTIFY_SOURCE complaining about stack trace caller ftrace: Fix possible warning on checking all pages used in ftrace_process_locs() ring-buffer: Fix deadloop issue on reading trace_pipe tracing: arm64: Avoid missing-prototype warnings selftests/user_events: Test struct size match cases tracing/user_events: Fix struct arg size match check x86/ftrace: Remove unsued extern declaration ftrace_regs_caller_ret() arm64: ftrace: Add direct call trampoline samples support samples: ftrace: Save required argument registers in sample trampolines
-
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tipLinus Torvalds authored
Pull xen fixes from Juergen Gross: - a cleanup of the Xen related ELF-notes - a fix for virtio handling in Xen dom0 when running Xen in a VM * tag 'for-linus-6.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/virtio: Fix NULL deref when a bridge of PCI root bus has no parent x86/Xen: tidy xen-head.S
-
git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linuxLinus Torvalds authored
Pull sh fixes from John Paul Adrian Glaubitz: "The sh updates introduced multiple regressions. In particular, the change a8ac2961 ("sh: Avoid using IRQ0 on SH3 and SH4") causes several boards to hang during boot due to incorrect IRQ numbers. Geert Uytterhoeven has contributed patches that handle the virq offset in the IRQ code for the dreamcast, highlander and r2d boards while Artur Rojek has contributed a patch which handles the virq offset for the hd64461 companion chip" * tag 'sh-for-v6.5-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux: sh: hd64461: Handle virq offset for offchip IRQ base and HD64461 IRQ sh: mach-dreamcast: Handle virq offset in cascaded IRQ demux sh: mach-highlander: Handle virq offset in cascaded IRL demux sh: mach-r2d: Handle virq offset in cascaded IRL demux
-
Zheng Yejian authored
kmemleak reports: unreferenced object 0xffff88814d14e200 (size 256): comm "cat", pid 336, jiffies 4294871818 (age 779.490s) hex dump (first 32 bytes): 04 00 01 03 00 00 00 00 08 00 00 00 00 00 00 00 ................ 0c d8 c8 9b ff ff ff ff 04 5a ca 9b ff ff ff ff .........Z...... backtrace: [<ffffffff9bdff18f>] __kmalloc+0x4f/0x140 [<ffffffff9bc9238b>] trace_find_next_entry+0xbb/0x1d0 [<ffffffff9bc9caef>] trace_print_lat_context+0xaf/0x4e0 [<ffffffff9bc94490>] print_trace_line+0x3e0/0x950 [<ffffffff9bc95499>] tracing_read_pipe+0x2d9/0x5a0 [<ffffffff9bf03a43>] vfs_read+0x143/0x520 [<ffffffff9bf04c2d>] ksys_read+0xbd/0x160 [<ffffffff9d0f0edf>] do_syscall_64+0x3f/0x90 [<ffffffff9d2000aa>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8 when reading file 'trace_pipe', 'iter->temp' is allocated or relocated in trace_find_next_entry() but not freed before 'trace_pipe' is closed. To fix it, free 'iter->temp' in tracing_release_pipe(). Link: https://lore.kernel.org/linux-trace-kernel/20230713141435.1133021-1-zhengyejian1@huawei.com Cc: stable@vger.kernel.org Fixes: ff895103 ("tracing: Save off entry when peeking at next entry") Signed-off-by:Zheng Yejian <zhengyejian1@huawei.com> Signed-off-by:
Steven Rostedt (Google) <rostedt@goodmis.org>
-
Paolo Abeni authored
Pedro Tammela says: ==================== net/sched: fixes for sch_qfq Patch 1 fixes a regression introduced in 6.4 where the MTU size could be bigger than 'lmax'. Patch 3 fixes an issue where the code doesn't account for qdisc_pkt_len() returning a size bigger then 'lmax'. Patches 2 and 4 are selftests for the issues above. ==================== Link: https://lore.kernel.org/r/20230711210103.597831-1-pctammela@mojatatu.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Pedro Tammela authored
A packet with stab overhead greater than QFQ_MAX_LMAX should be dropped by the QFQ qdisc as it can't handle such lengths. Signed-off-by:
Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by:
-
Pedro Tammela authored
Lion says: ------- In the QFQ scheduler a similar issue to CVE-2023-31436 persists. Consider the following code in net/sched/sch_qfq.c: static int qfq_enqueue(struct sk_buff *skb, struct Qdisc *sch, struct sk_buff **to_free) { unsigned int len = qdisc_pkt_len(skb), gso_segs; // ... if (unlikely(cl->agg->lmax < len)) { pr_debug("qfq: increasing maxpkt from %u to %u for class %u", cl->agg->lmax, len, cl->common.classid); err = qfq_change_agg(sch, cl, cl->agg->class_weight, len); if (err) { cl->qstats.drops++; return qdisc_drop(skb, sch, to_free); } // ... } Similarly to CVE-2023-31436, "lmax" is increased without any bounds checks according to the packet length "len". Usually this would not impose a problem because packet sizes are naturally limited. This is however not the actual packet length, rather the "qdisc_pkt_len(skb)" which might apply size transformations according to "struct qdisc_size_table" as created by "qdisc_get_stab()" in net/sched/sch_api.c if the TCA_STAB option was set when modifying the qdisc. A user may choose virtually any size using such a table. As a result the same issue as in CVE-2023-31436 can occur, allowing heap out-of-bounds read / writes in the kmalloc-8192 cache. ------- We can create the issue with the following commands: tc qdisc add dev $DEV root handle 1: stab mtu 2048 tsize 512 mpu 0 \ overhead 999999999 linklayer ethernet qfq tc class add dev $DEV parent 1: classid 1:1 htb rate 6mbit burst 15k tc filter add dev $DEV parent 1: matchall classid 1:1 ping -I $DEV 1.1.1.2 This is caused by incorrectly assuming that qdisc_pkt_len() returns a length within the QFQ_MIN_LMAX < len < QFQ_MAX_LMAX. Fixes: 462dbc91 ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost") Reported-by:Lion <nnamrec@gmail.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Pedro Tammela authored
QFQ only supports a certain bound of MTU size so make sure we check for this requirement in the tests. Acked-by:
-
Pedro Tammela authored
25369891 deletes a check for the case where no 'lmax' is specified which 30379334 previously fixed as 'lmax' could be set to the device's MTU without any bound checking for QFQ_LMAX_MIN and QFQ_LMAX_MAX. Therefore, reintroduce the check. Fixes: 25369891 ("net/sched: sch_qfq: refactor parsing of netlink parameters") Acked-by:
-
Artur Rojek authored
A recent change to start counting SuperH IRQ #s from 16 breaks support for the Hitachi HD64461 companion chip. Move the offchip IRQ base and HD64461 IRQ # by 16 in order to accommodate for the new virq numbering rules. Fixes: a8ac2961 ("sh: Avoid using IRQ0 on SH3 and SH4") Signed-off-by:
Artur Rojek <contact@artur-rojek.eu> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Link: https://lore.kernel.org/r/20230710233132.69734-1-contact@artur-rojek.euSigned-off-by:
-
Geert Uytterhoeven authored
Take into account the virq offset when translating cascaded interrupts. Fixes: a8ac2961 ("sh: Avoid using IRQ0 on SH3 and SH4") Signed-off-by:
-
Geert Uytterhoeven authored
Take into account the virq offset when translating cascaded IRL interrupts. Fixes: a8ac2961 ("sh: Avoid using IRQ0 on SH3 and SH4") Signed-off-by:
-
Geert Uytterhoeven authored
When booting rts7751r2dplus_defconfig on QEMU, the system hangs due to an interrupt storm on IRQ 20. IRQ 20 aka event 0x280 is a cascaded IRL interrupt, which maps to IRQ_VOYAGER, the interrupt used by the Silicon Motion SM501 multimedia companion chip. As rts7751r2d_irq_demux() does not take into account the new virq offset, the interrupt is no longer translated, leading to an unhandled interrupt. Fix this by taking into account the virq offset when translating cascaded IRL interrupts. Fixes: a8ac2961 ("sh: Avoid using IRQ0 on SH3 and SH4") Reported-by:
Guenter Roeck <linux@roeck-us.net> Closes: https://lore.kernel.org/r/fbfea3ad-d327-4ad5-ac9c-648c7ca3fe1f@roeck-us.netSigned-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski authored
Alexei Starovoitov says: ==================== pull-request: bpf 2023-07-12 We've added 5 non-merge commits during the last 7 day(s) which contain a total of 7 files changed, 93 insertions(+), 28 deletions(-). The main changes are: 1) Fix max stack depth check for async callbacks, from Kumar. 2) Fix inconsistent JIT image generation, from Björn. 3) Use trusted arguments in XDP hints kfuncs, from Larysa. 4) Fix memory leak in cpu_map_update_elem, from Pu. * tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf: xdp: use trusted arguments in XDP hints kfuncs bpf: cpumap: Fix memory leak in cpu_map_update_elem riscv, bpf: Fix inconsistent JIT image generation selftests/bpf: Add selftest for check_stack_max_depth bug bpf: Fix max stack depth check for async callbacks ==================== Link: https://lore.kernel.org/r/20230712223045.40182-1-alexei.starovoitov@gmail.comSigned-off-by:
-
Felix Fietkau authored
Fix ethernet header length field after stripping the mesh header Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/CT5GNZSK28AI.2K6M69OXM9RW5@syracuse/ Fixes: 986e43b1 ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces") Reported-and-tested-by:
Nicolas Escande <nico.escande@gmail.com> Signed-off-by:
Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20230711115052.68430-1-nbd@nbd.nameSigned-off-by:
-
Zhang Shurong authored
If there is a failure during rtw89_fw_h2c_raw() rtw89_debug_priv_send_h2c should return negative error code instead of a positive value count. Fix this bug by returning correct error code. Fixes: e3ec7017 ("rtw89: add Realtek 802.11ax driver") Signed-off-by:
Zhang Shurong <zhang_shurong@foxmail.com> Acked-by:
Ping-Ke Shih <pkshih@realtek.com> Link: https://lore.kernel.org/r/tencent_AD09A61BC4DA92AD1EB0790F5C850E544D07@qq.comSigned-off-by:
-
- 12 Jul, 2023 1 commit
-
-
Jiawen Wu authored
For some device types like TXGBE_ID_XAUI, *checksum computed in txgbe_calc_eeprom_checksum() is larger than TXGBE_EEPROM_SUM. Remove the limit on the size of *checksum. Fixes: 049fe536 ("net: txgbe: Add operations to interact with firmware") Fixes: 5e2ea780 ("net: txgbe: Fix unsigned comparison to zero in txgbe_calc_eeprom_checksum()") Signed-off-by:
-
