Fill out the lower three digits for gen2 and gen3 cdclk frqeuncy. It's
not clear if these are accurate frquencies or just in the ballpark, but
without docs this is the best we can do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

ns2501 requires the DVO 2x clock before it will respond to i2c access,
so make sure the clock is enabled when we try to initialize the encoder.

Fixes the display getting lost on module reload on my Fujitsu/Siemens
Lifebook S6010.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

After the GPU has wedged we can't turn on the overlay anymore. Only mark
it as active if we succeed in allocating ring space. This prevents a
WARN (previous;y a BUG) during driver unload if we attempted to use the
overlay after the GPU had already wedged.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

overlay.{active,pfit_active} are just on/off flags, so make them bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

BUG is bad, just use WARN.

Also drop one BUG(!overlay) since we'd oops anyway when dereferencing
it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

On CHV, PUNIT team confirmed that 'VLV_GFX_CLK_STATUS_BIT' is not a
sticky bit and it will always be set. So ignore Check for previous
Gfx force off during suspend and allow the force clk as part S0ix
Sequence
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

BSpec recommends to keep the main link state consistent
between the source and the sink. As per that, update
the main link state in sink DPCD register to 'active',
for Valleyview based platforms.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Thomas Richter <thor@math.tu-berlin.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We were missing a convenience stub to aquire the right mutex whilst
dropping the request, so add it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Makes that code atomic ready.

v2: Acquire crtc_state for the "other" pipe only when needed. (Daniel)

v3: Really only acquire the other state if necessary. (Daniel)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Backmerge Linux 4.0-rc6 because conflicts are (again) getting out of
hand. To make sure we don't lose any bugfixes from the 4.0-rc5-rc6
flurry of patches we've applied them all to -next too.

Conflicts:
	drivers/gpu/drm/i915/intel_display.c

Always take the version from -next, we've already handled all
conflicts with explicit cherrypicking.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

Pull ARM SoC fixes from Olof Johansson:
 "The latest and greatest fixes for ARM platform code.  Worth pointing
  out are:

   - Lines-wise, largest is a PXA fix for dealing with interrupts on DT
     that was quite broken.  It's still newish code so while we could
     have held this off, it seemed appropriate to include now

   - Some GPIO fixes for OMAP platforms added a few lines.  This was
     also fixes for code recently added (this release).

   - Small OMAP timer fix to behave better with partially upstreamed
     platforms, which is quite welcome.

   - Allwinner fixes about operating point control, reducing
     overclocking in some cases for better stability.

  plus a handful of other smaller fixes across the map"

* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: juno: Fix misleading name of UART reference clock
  ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
  ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
  ARM: socfpga: dts: fix spi1 interrupt
  ARM: dts: Fix gpio interrupts for dm816x
  ARM: dts: dra7: remove ti,hwmod property from pcie phy
  ARM: OMAP: dmtimer: disable pm runtime on remove
  ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
  ARM: OMAP2+: Fix socbus family info for AM33xx devices
  ARM: dts: omap3: Add missing dmas for crypto
  ARM: dts: rockchip: disable gmac by default in rk3288.dtsi
  MAINTAINERS: add rockchip regexp to the ARM/Rockchip entry
  ARM: pxa: fix pxa interrupts handling in DT
  ARM: pxa: Fix typo in zeus.c
  ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage

Merge tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes

Allwinner fixes for 4.0

There's a few fixes to merge for 4.0, one to add a select in the machine
Kconfig option to fix a potential build failure, and two fixing cpufreq related
issues.

* tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
  ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
  ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for the -rc cycle:

- Fix a device tree based booting vs legacy booting regression for
  omap3 crypto hardware by adding the missing DMA channels.

- Fix /sys/bus/soc/devices/soc0/family for am33xx devices.

- Fix two timer issues that can cause hangs if the timer related
  hwmod data is missing like it often initially is for new SoCs.

- Remove pcie hwmods entry from dts as that causes runtime PM to
  fail for the PHYs.

- A paper bag type dts configuration fix for dm816x GPIO
  interrupts that I just noticed. This is most of the changes
  diffstat wise, but as it's a basic feature for connecting
  devices and things work otherwise, it should be fixed.

* tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: Fix gpio interrupts for dm816x
  ARM: dts: dra7: remove ti,hwmod property from pcie phy
  ARM: OMAP: dmtimer: disable pm runtime on remove
  ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
  ARM: OMAP2+: Fix socbus family info for AM33xx devices
  ARM: dts: omap3: Add missing dmas for crypto
Signed-off-by: Olof Johansson <olof@lixom.net>

Late fix for v4.0 on the SoCFPGA platform:
- Fix interrupt number for SPI1 interface

* tag 'socfpga_fix_for_v4.0_2' of git://git.rocketboards.org/linux-socfpga-next:
  ARM: socfpga: dts: fix spi1 interrupt
Signed-off-by: Olof Johansson <olof@lixom.net>

The UART reference clock speed is 7273.8 kHz, not 72738 kHz.

Dots aren't usually used in node names even though ePAPR permits
them.  However, this can easily be avoided by expressing the
frequency in Hz, not kHz.

This patch changes the name to refclk7273800hz, reflecting the
actual clock speed.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

arm: pxa: fixes for v4.0-rc5

There are only 2 fixes, one for the zeus board about the regulator changes,
where a typo prevented the zeus board from having a working can regulator,
and one regression triggered by the interrupts IRQ shift of 16 affecting all
boards.

* tag 'fixes-for-v4.0-rc5' of https://github.com/rjarzmik/linux:
  ARM: pxa: fix pxa interrupts handling in DT
  ARM: pxa: Fix typo in zeus.c
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull x86 fix from Ingo Molnar:
 "Fix x86 syscall exit code bug that resulted in spurious non-execution
  of TIF-driven user-return worklets, causing big trouble for things
  like KVM that rely on user notifiers for correctness of their vcpu
  model, causing crashes like double faults"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm/entry: Check for syscall exit work with IRQs disabled

Pull timer fixes from Ingo Molnar:
 "Two clocksource driver fixes, and an idle loop RCU warning fix"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/sun5i: Fix cpufreq interaction with sched_clock()
  clocksource/drivers: Fix various !CONFIG_HAS_IOMEM build errors
  timers/tick/broadcast-hrtimer: Fix suspicious RCU usage in idle loop

Pull scheduler fix from Ingo Molnar:
 "A single sched/rt corner case fix for RLIMIT_RTIME correctness"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix RLIMIT_RTTIME when PI-boosting to RT

Pull perf fix from Ingo Molnar:
 "A perf kernel side fix for a fuzzer triggered lockup"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix irq_work 'tail' recursion

Pull locking fix from Ingo Molnar:
 "A module unload lockdep race fix"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  lockdep: Fix the module unload key range freeing logic

Pull parsic fixes from Helge Deller:
 "One patch from Mikulas fixes a bug on parisc by artifically
  incrementing the counter in pmd_free when the kernel tries to free
  the preallocated pmd.

  Other than that we now prevent that syscalls gets added without
  incrementing __NR_Linux_syscalls and fix the initial pmd setup code
  if a default page size greater than 4k has been selected"

* 'parisc-4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix pmd code to depend on PT_NLEVELS value, not on CONFIG_64BIT
  parisc: mm: don't count preallocated pmds
  parisc: Add compile-time check when adding new syscalls

Pull kvm ppc bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Book3S HV: Fix instruction emulation
  KVM: PPC: Book3S HV: Endian fix for accessing VPA yield count
  KVM: PPC: Book3S HV: Fix spinlock/mutex ordering issue in kvmppc_set_lpcr()

Pull ARC fixes from Vineet Gupta:
 "We found some issues with signal handling taking down the system.  I
  know its late, but these are important and all marked for stable.

  ARC signal handling related fixes uncovered during recent testing of
  NPTL tools"

* tag 'arc-4.0-fixes-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: signal handling robustify
  ARC: SA_SIGINFO ucontext regs off-by-one

Pull selinux bugfix from James Morris.

Fix broken return value.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selinux: fix sel_write_enforce broken return value

Pull watchdog fixes from Wim Van Sebroeck:

 - mtk_wdt: signedness bug in mtk_wdt_start()

 - imgpdc: Fix NULL pointer dereference during probe and fix the default
   heartbeat

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: imgpdc: Fix default heartbeat
  watchdog: imgpdc: Fix probe NULL pointer dereference
  watchdog: mtk_wdt: signedness bug in mtk_wdt_start()

Pull sound fixes from Takashi Iwai:
 "Three trivial oneliner fixes for HD-audio.

  Two are device-specific quirks while one is a generic fix for recent
  Realtek codecs"

* tag 'sound-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Add one more node in the EAPD supporting candidate list
  ALSA: hda_intel: apply the Seperate stream_tag for Sunrise Point
  ALSA: hda - Add dock support for Thinkpad T450s (17aa:5036)

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Since

commit 17cabf57
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Wed Jan 14 11:20:57 2015 +0000

    drm/i915: Trim the command parser allocations

we may then try to allocate a zero-sized object and attempt to extract
its pages. Understandably this fails.

Testcase: igt/gem_exec_nop #ivb,byt,hsw
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The return value of one of the calls to drm_atomic_get_connector_state()
in intel_modeset_stage_output_state() wasn't checked for errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

To allow for views where the view type is not defined by the view type only,
like it is in stereo or rotated 90 degree view, change the semantic to require
the whole view structure for comparison when we match a GGTT view.

This allows including parameters like offset to be included in the view which
is useful for eg. partial views.

v3:
- Rely on ggtt_view type being 0 for non-GGTT vma's, which equals to
  I915_GGTT_VIEW_NORMAL. (Daniel Vetter)
- Do not use potentially slower comparison when we only want to know if
  something is or is not a normal view.
- Rebase on top of rotated view patches. Add rotated view singleton.
- If one view is missing in comparison they're equal only if both are missing.

v4:
- Use comparison helper in obj_to_ggtt_view too. (Tvrtko Ursulin)
- Do WARN_ON if one view is NULL. (Tvrtko Ursulin)

Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drivers/gpu/drm/i915/i915_gem_gtt.c:1349:1-4: WARNING: end returns can be simpified and declaration on line 1347 can be dropped

 Simplify a trivial if-return sequence.  Possibly combine with a
 preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci

CC: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This is useful for writing igts to make sure we don't break this,
without being forced to own a one of these dinosaurs.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Some of the crtc_compute_clock() still depended on encoder->new_crtc
since they didn't use intel_pipe_will_have_type() and used an open
coded version of that function instead. This patch replaces those with
the appropriate code that checks the atomic state intead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Separate the if (!connector) continue to facility easier
extraction of a loop iterator for all of these (there's lots more in
i915 and atomic helpers).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The function intel_dp_set_drrs_state() would decide which pipe to
downclock based on the staged config for the given connector. However,
the result of that function is immediate, and it uses input values from
crtc->config, so it should be looking at the current crtc instead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pass a crtc_state to it and find whether the pipe has an encoder of a
given type by looking at the drm_atomic_state the crtc_state points to.

Until recently i9xx_get_refclk() used to be called indirectly from
vlv_force_pll_on() with a dummy crtc_state. That dummy crtc state is not
converted to be part of a full drm atomic state, so add a WARN in case
someone decides to call that again with a such dummy state. This was
removed in

commit 9cbe40c1
Author: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Date:   Thu Mar 5 19:33:08 2015 +0530

    drm/i915: Update prop, int co-eff and gain threshold for CHV

v2: Warn if there is no connectors for a given crtc. (Daniel)
    Replace comment i9xx_get_refclk() with a WARN_ON(). (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Add commit reference for when i9xx_get_refclk was removed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Follow up patches will convert some functions called from there to use
the atomic state, instead of directly accessing the new or current
config. This patch just changes the parameters, but shouldn't have any
functional changes.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>