Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In case a descriptor has the "done" bit clear and the
next descriptor has it set, we drop both of them. If
the packet that is received after these two packets
is dropped for some reason, "discard_next" will not cleared.
Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The MIC/PHYERR/CRC error bits are valid only for
the last desc. for chained packets. Check this early
in the preprocess() routine and bail out.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make sure that chained descriptors are handled correctly
before the packet is parsed to determine if it is a beacon.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Handle chained descriptors and increment the RX counter
only for valid packets. Since this is used only by MCI,
use CONFIG_ATH9K_BTCOEX_SUPPORT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The various error bits that ath_debug_stat_rx()
checks are valid only for the last descriptor for
a chained packet, handle this correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Parse the PHY error details only for the last fragment
in case descriptors are chained.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is no need to calculate the mactime for chained
descriptor packets, so make sure that this is done
only for the last fragment of valid packets.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The keymiss events are valid only in the last descriptor
of a packet. Fix this by making sure that we return
early in case of chained descriptors.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Frames with invalid or zero length can be discarded
early, there is no need to check the crypto bits.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since the DFS code appears to process the phy errors
ATH9K_PHYERR_RADAR and ATH9K_PHYERR_FALSE_RADAR_EXT,
check for the correct phyerr status in the main RX
tasklet routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If usb auto suspend is enabled or system run in to suspend/resume
cycle, ath9k-htc adapter will stop to response. It is reproducible on xhci HCs.

Host part of problem:
XHCI do timing calculation based on Transfer Type and bInterval,
immediately after device was detected. Ath9k-htc try to overwrite
this parameters on module probe and some changes in FW,
since we do not initiate usb reset from the driver this changes
are not took to account. So, before any kind of suspend or reset,
host controller will operate with old parameters. Only after suspend/resume
and if interface id stay unchanged, new parameters will by applied. Host
will send bulk data with no intervals (?), which will cause
overflow on FIFO of EP4.

Firmware part of problem:
By default, ath9k-htc adapters configured with EP3 and EP4
as interrupt endpoints. Current firmware will try to overwrite
ConfigDescriptor to make EP3 and EP4 bulk. FIFO for this endpoints
stay not reconfigured, so under the hood it is still Int EP.

This patch is revert of 4a0e8ecc commit which trying to
reduce CPU usage on some systems. Since it will produce more bug
as fixes, we will need to find other way to fix it.

here is comment from kernel source which has some more explanation:
* Some buggy high speed devices have bulk endpoints using
* maxpacket sizes other than 512.  High speed HCDs may not
* be able to handle that particular bug, so let's warn...

in our case EP3 and EP4 have maxpacket sizes = 64!!!
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix for TCP iperf from Windows to Linux stall after about 1sec

Hardware reports false errors in some situations:

Microsoft IP stack, in violation of RFC 1624, set TCP checksum that should be 0x0
as 0xffff. hardware report Rx csum error. If HW csum absolutely trusted,
this frame can be never received, as re-transmitted one will have same csum problem.
In addition, it mess up block ack reorder buffer, as if packet dropped, it is not score boarded
there.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If that flag stays set for a buffer that already ran through the tx path
once, it might cause issues in tx completion processing. Better clear it
early to ensure that this does not happen
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath_tid_drain is only called when a station entry is being removed, so
there is no point in still tracking BAW state. Remove some unnecessary
code and a bogus TODO comment related to this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

They are not implemented, and accessing them might trigger errors

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Writing to that file is unnecessary and quirky, the antenna API should
be used instead. Use debugfs_create_u8 to allow reading the values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 uses debugfs_remove_recursive, so there's no need for the
driver to do an explicit cleanup of its sta debugfs entry.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also reduce the size of a few fields where possible
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Similar to a race condition that exists in the tx path, the hardware
might re-read the 'next' pointer of a descriptor of the last completed
frame. This only affects non-EDMA (pre-AR93xx) devices.

To deal with this race, defer clearing and re-linking a completed rx
descriptor until the next one has been processed.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Host tx glomming require an extended hardware sdio bus header to store
information for dongle. Introduce a variable in struct brcmf_sdio to replace
macro SDPCM_HDRLEN
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Streamlining sdio bus specific header related code as preparation for host
tx glomming
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

remove align from brcmf_bus since it is only used by sdio bus layer internally
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Abstract brcmf_sdio_txpkt_prep and brcmf_sdio_txpkt_postp as a preparation
of chained tx packets for host side tx glomming.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Implement the .tdls_oper() callback and indicate TDLS support
in the wiphy flags.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Not every IF event from the firmware needs to result in a
related interface, netdev or wdev, on the host. This is
indicated in the event message. Handle that flag and effectively
ignore the firmware event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

FWS uses locking to protect its data while being called from
various entries. On bus_txdata the lock was kept resulting in
unnecessary long locking, but also creating possibility for
deadlock. This update changes the locking to release lock when
bus_txdata is called.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When fw signalling is disabled tx is sent immediately. Using
queues and worker thread allows usb to do synchronous autopm. This
patch makes fws use queues and worker thread even if signalling is
not supported by FW or not enabled.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This feature moves the responsibility of collecting all MPDUs in an
AMPDU session in the correct order from the firmware to the host
driver. This reduces buffer requirement on the firmware side.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With firmware-signalling the packet handed to the bus specific driver
layer should not be discarded with brcmf_txcomplete() in the failure
path. Instead only an error is returned and the caller decides what
to do with the packet.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware-signalling needs transmit to firmware to be atomic and
uses a spinlock with irq disabled. Therefor, brcmf_sdbrcm_txdata()
should not use spin_unlock_bh() as it would enable the interrupts.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Samuel Ortiz <sameo@linux.intel.com> says:

"This is the first NFC pull request for the 3.12 release.

With this one we have:

- A few pn533 improvements and minor fixes. Testing our pn533 driver
  against Google's NCI stack triggered a few issues that we fixed now.
  We also added Tx fragmentation support to this driver.

- More NFC secure element handling. We added a GET_SE netlink command
  for getting all the discovered secure elements, and we defined 2
  additional secure element netlink event (transaction and connectivity).
  We also fixed a couple of typos and copy-paste bugs from the secure
  element handling code.

- Firmware download support for the pn544 driver. This chipset can enter a
  special mode where it's waiting for firmware blobs to replace the
  already flashed one. We now support that mode."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The secure element state was not updated from the enable/disable ops,
leaving the SE state to disabled for ever.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Another typo from the initial commit where we check for the secure
element type field instead of its state when enabling or disabling it.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

There is a cut and paste bug so we enable a second time instead of
disabling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The pn544 can enter a firmware update mode where firmware blobs can be
pushed through the i2c line and flashed on the target.
A special command allows to verify that blobs are correctly flashed and
this is what we do for every downloaded firmware blob.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>