- 25 May, 2020 40 commits
-
-
Colin Ian King authored
Currently pointer ep is being dereferenced before it is null checked leading to a null pointer dereference issue. Fix this by only assigning pointer udc once ep is known to be not null. Also remove a debug message that requires a valid udc which may not be possible at that point. Addresses-Coverity: ("Dereference before null check") Fixes: 24a28e42 ("USB: gadget driver for LPC32xx") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org>
-
Yu Chen authored
If the SS PHY is in P3, there is no pipe_clk, HW may use suspend_clk for function, as suspend_clk is slow so EP command need more time to complete, e.g, imx8M suspend_clk is 32K, set ep configuration will take about 380us per below trace time stamp(44.286278 - 44.285897 = 0.000381): configfs_acm.sh-822 [000] d..1 44.285896: dwc3_writel: addr 000000006d59aae1 value 00000401 configfs_acm.sh-822 [000] d..1 44.285897: dwc3_readl: addr 000000006d59aae1 value 00000401 ... ... configfs_acm.sh-822 [000] d..1 44.286278: dwc3_readl: addr 000000006d59aae1 value 00000001 configfs_acm.sh-822 [000] d..1 44.286279: dwc3_gadget_ep_cmd: ep0out: cmd 'Set Endpoint Configuration' [401] params 00001000 00000500 00000000 --> status: Successful This was originally found on Hisilicon Kirin Soc that need more time for the device controller to clear the CmdAct of DEPCMD. Signed-off-by:
Yu Chen <chenyu56@huawei.com> Signed-off-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
Li Jun <jun.li@nxp.com> Signed-off-by:
-
Andrey Konovalov authored
USB gadget subsystem uses the following naming convention for UDC endpoints: - "ep-a" names for fully configurable endpoints (address, direction and transfer type can be changed); - "ep1in", "ep12out-bulk" names for fixed function endpoints (fixed address, direction and/or transfer type). Dummy UDC endpoints are capable of full configuration, but named using the second scheme. This patch changes the names of generic Dummy UDC endpoints to "ep-aout", "ep-bin", etc., to advertise that they have configurable addresses and transfer types (except that Dummy UDC doesn't support ISO transfers), but fixed direction. This is required for Raw Gadget (and perhaps for some other drivers), that reasons about whether an endpoint has configurable address based on its name. Suggested-by:
Alan Stern <stern@rowland.harvard.edu> Acked-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
-
Peter Chen authored
Assign interrupt number to USB gadget structure. Reviewed-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Peter Chen authored
The threaded interrupt handler may still be called after the usb_gadget_disconnect is called, it causes the structures used at interrupt handler was freed before it uses, eg the usb_request. This issue usually occurs we remove the udc function during the transfer. Below is the example when doing stress test for android switch function, the EP0's request is freed by .unbind (configfs_composite_unbind -> composite_dev_cleanup), but the threaded handler accesses this request during handling setup packet request. In fact, there is no protection between unbind the udc and udc interrupt handling, so we have to avoid the interrupt handler is occurred or scheduled during the .unbind flow. init: Sending signal 9 to service 'adbd' (pid 18077) process group... android_work: did not send uevent (0 0 000000007bec2039) libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 6ms init: Service 'adbd' (pid 18077) received signal 9 init: Sending signal 9 to service 'adbd' (pid 18077) process group... libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 0ms init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:14) init: Received control message 'start' for 'adbd' from pid: 399 (/vendor/bin/hw/android.hardware.usb@1. init: starting service 'adbd'... read descriptors read strings Unable to handle kernel read from unreadable memory at virtual address 000000000000002a android_work: sent uevent USB_STATE=CONNECTED Mem abort info: ESR = 0x96000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 Data abort info: ISV = 0, ISS = 0x00000004 CM = 0, WnR = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=00000000e97f1000 using random self ethernet address [000000000000002a] pgd=0000000000000000 Internal error: Oops: 96000004 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 232 Comm: irq/68-5b110000 Not tainted 5.4.24-06075-g94a6b52b5815 #92 Hardware name: Freescale i.MX8QXP MEK (DT) pstate: 00400085 (nzcv daIf +PAN -UAO) using random host ethernet address pc : composite_setup+0x5c/0x1730 lr : android_setup+0xc0/0x148 sp : ffff80001349bba0 x29: ffff80001349bba0 x28: ffff00083a50da00 x27: ffff8000124e6000 x26: ffff800010177950 x25: 0000000000000040 x24: ffff000834e18010 x23: 0000000000000000 x22: 0000000000000000 x21: ffff00083a50da00 x20: ffff00082e75ec40 x19: 0000000000000000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000001 x11: ffff80001180fb58 x10: 0000000000000040 x9 : ffff8000120fc980 x8 : 0000000000000000 x7 : ffff00083f98df50 x6 : 0000000000000100 x5 : 00000307e8978431 x4 : ffff800011386788 x3 : 0000000000000000 x2 : ffff800012342000 x1 : 0000000000000000 x0 : ffff800010c6d3a0 Call trace: composite_setup+0x5c/0x1730 android_setup+0xc0/0x148 cdns3_ep0_delegate_req+0x64/0x90 cdns3_check_ep0_interrupt_proceed+0x384/0x738 cdns3_device_thread_irq_handler+0x124/0x6e0 cdns3_thread_irq+0x94/0xa0 irq_thread_fn+0x30/0xa0 irq_thread+0x150/0x248 kthread+0xfc/0x128 ret_from_fork+0x10/0x18 Code: 910e8000 f9400693 12001ed7 79400f79 (3940aa61) ---[ end trace c685db37f8773fba ]--- Kernel panic - not syncing: Fatal exception SMP: stopping secondary CPUs Kernel Offset: disabled CPU features: 0x0002,20002008 Memory Limit: none Rebooting in 5 seconds.. Reviewed-by:
-
Sandeep Maheswaram authored
Populate USB DT nodes with interconnect properties. Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Signed-off-by:
Sandeep Maheswaram <sanm@codeaurora.org> Signed-off-by:
-
Sandeep Maheswaram authored
Populate USB DT nodes with interconnect properties. Reviewed-by:
-
Sandeep Maheswaram authored
Add documentation for the interconnects and interconnect-names properties for USB. Reviewed-by:
Rob Herring <robh@kernel.org> Reviewed-by:
-
Gregory CLEMENT authored
The endpoint configuration used to be stored in the device tree, however the configuration depend on the "version" of the controller itself. Then the EP child node are useless and describe as deprecated in the documentation binding: remove all the nodes from the SoC device tree file. Remove also the #address-cells and #size-cells properties that are no longer needed. Signed-off-by:
Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by:
-
Gregory CLEMENT authored
There is no need to describe the end point in the deice tree. These properties won't be use anymore, so mark them as deprecated to keep the old device tree documented. Reviewed-by:
-
Gregory CLEMENT authored
The endpoint configuration used to be stored in the device tree, however the configuration depend on the "version" of the controller itself. This information is already documented by the compatible string. It then possible to just rely on the compatible string and completely remove the full ep configuration done in the device tree as it was already the case for all the other USB device controller. Acked-by:
Cristian Birsan <cristian.birsan@microchip.com> Signed-off-by:
-
Thinh Nguyen authored
DWC_usb32 v1.00a and later can use SET_EP_PRIME command to reinitiate a stream. Use the command to handle NoStream rejection instead of ending and restarting the endpoint. Signed-off-by:
Thinh Nguyen <thinhn@synopsys.com> Signed-off-by:
-
Thinh Nguyen authored
Overview of stream transfer requirement: * A transfer will have a set of TRBs of the same stream ID. * A transfer is started with a stream ID in START_TRANSFER command. * A new stream will only start when the previous completes. Overview of stream events: * A "prime" from host indicates that its endpoints are active (buffers prepared and ready to receive/transmit data). The controller automatically initiates stream if it sees this. * A "NoStream" rejection event indicates that the host isn't ready. Host will put the endpoint back to idle state. Device may need to reinitiate the stream to start transfer again. * A Stream Found event means host accepted device initiated stream. Nothing needs to be done from driver. To initiate a stream, the driver will issue START_TRANSFER command with a stream ID. To reinitiate the stream, the driver must issue END_TRANSFER and restart the transfer with START_TRANSFER command with the same stream ID. This implementation handles device-initated streams (e.g. UASP driver). It also handles some hosts' quirky behavior where they only prime each endpoint once. Signed-off-by:
-
Thinh Nguyen authored
Don't prepare TRBs beyond a transfer. In DWC_usb32, its transfer burst capability may try to read and use TRBs beyond the active transfer. For other controllers, they don't process the next transfer TRBs until the current transfer is completed. Explicitly prevent preparing TRBs ahead for all controllers. Signed-off-by:
-
Thinh Nguyen authored
If a transfer is in-progress, any new request should not kick off another transfer. The driver needs to wait for the current transfer to complete before starting off the next transfer. Introduce a new flag DWC3_EP_WAIT_TRANSFER_COMPLETE for this. Signed-off-by:
-
Thinh Nguyen authored
In DWC3, to prepare TRBs for streams, all the TRBs of a transfer will use the same stream ID. To start a new stream, the driver needs to wait for the current transfer to complete or ended (by END_TRANFER command). As a result, inform the controller of the last TRB of a transfer so that it knows when a transfer completes and start a new transfer of a new stream. Even though the transfer completion handling can be applied for other non-isoc endpoints, only do it for streams due to its requirement. It's better to keep the controller's TRB cache full than waiting for transfer completion and starting a new transfer. Signed-off-by:
-
Thinh Nguyen authored
To switch from one stream to another, this requires the driver to start a new transfer with a specific stream ID. For a transfer to complete, the driver needs to indicate the last TRB of a transfer, and it needs to enable XferComplete event to handle completed TRBs of a transfer. Let's enable this event only for stream capable endpoints. Signed-off-by:
-
Thinh Nguyen authored
To prepare for handling of XferComplete event, let's refactor and split up dwc3_gadget_endpoint_transfer_in_progress() to handle TRBs completion for different events. The handling of TRBs completion will be the same, but the status of XferComplete event is different than XferInProgress. No functional change in this commit. Signed-off-by:
-
Thinh Nguyen authored
While handling TRBs completion, if a END_TRANSFER command isn't completed, don't kick new transfer or issue END_TRANSFER command. Signed-off-by:
-
Thinh Nguyen authored
Set the request->is_last to each stream request to indicate that the request is the last stream request of a transfer. The DWC3 controller needs to know this info to properly switch streams. The current implementation of f_tcm uses a single request per transfer, so every stream request is the last of its stream. Signed-off-by:
-
Thinh Nguyen authored
To take advantage of DWC3 internal TRB prefetch and cache for performance, inform the controller the last request with stream_id before switching to a different stream transfer. This allows the controller to maintain its transfer burst within the stream ID. Introduce the usb-request is_last field to help inform the DWC3 controller of this. Signed-off-by:
-
Thinh Nguyen authored
DWC_usb32 supports MDWIDTH value larger than 255 and up to 1023. The field HWPARAMS6[9:8] stores the upper 2-bit values of the DWC_usb32's MDWIDTH. Check that parameter and properly get the MDWIDTH for DWC_usb32. Signed-off-by:
-
Thinh Nguyen authored
Synopsys introduces a new controller DWC_usb32. It supports dual-lane and speed up to 20 Gbps, and the DWC3 driver will drive this controller. Currently the driver uses a single field dwc->revision to ID both DWC_usb3 and DWC_usb31 and their version number. This was sufficient for two IPs, but this method doesn't work with additional IPs. As a result, let's separate the dwc->revision field to 2 separate fields: ip and revision. The ip field now stores the ID of the controller's IP while the revision field stores the controller's version number. This new scheme enforces DWC3 to compare the revision within the same IP only. As a result, we must update all the revision check of the controller to check its corresponding IP. To help with this enforcement, we create a few macros to help with the common version checks: DWC3_IP_IS(IP) DWC3_VER_IS(IP, VERSION) DWC3_VER_IS_PRIOR(IP, VERSION) DWC3_VER_IS_WITHIN(IP, LOWER_VERSION, UPPER_VERSION) DWC3_VER_TYPE_IS_WITHIN(IP, VERSION, LOWER_VERSION_TYPE, UPPER_VERSION_TYPE) The DWC_usb32 controller operates using the same programming model and with very similar configurations as its previous controllers. Please note that the various IP and revision checks in this patch match the current checks for DWC_usb31 version 1.90a. Additional configurations that are unique to DWC_usb32 are applied separately. Signed-off-by:
-
Nagarjuna Kristam authored
OTG port on Tegra194 supports GEN1 speeds when in device mode and GEN2 speeds when in host mode. dd port_speed_quirk that configures port to GEN1/GEN2 speds, corresponding to the mode. Based on work by WayneChang <waynec@nvidia.com> Signed-off-by:
Nagarjuna Kristam <nkristam@nvidia.com> Signed-off-by:
-
Nagarjuna Kristam authored
This commit adds support for XUSB device mode controller support on Tegra194 SoC. This is very similar to the existing Tegra186 XUDC, with lpm support added in addition. Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Nagarjuna Kristam authored
Extend the Tegra XUSB controller device tree binding with Tegra194 support. Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at set_link_state() warning: context imbalance in set_link_state() - unexpected unlock The root cause is the missing annotation at set_link_state() Add the missing __must_hold(&dum->lock) Signed-off-by:
Jules Irenge <jbi.octave@gmail.com> Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at xudc_handle_setup() warning: context imbalance in xudc_handle_setup() - unexpected unlock The root cause is the missing annotation at xudc_handle_setup() Add the missing __must_hold(&udc->lock) annotation Signed-off-by:
-
Wei Yongjun authored
module_usb_composite_driver() makes the code simpler by eliminating boilerplate code. Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Jason Yan authored
Fix the following coccicheck warning: drivers/usb/gadget/udc/omap_udc.c:2579:2-3: Unneeded semicolon Signed-off-by:
Jason Yan <yanaijie@huawei.com> Signed-off-by:
-
Jason Yan authored
Fix the following coccicheck warning: drivers/usb/gadget/udc/mv_u3d_core.c:1551:5-13: WARNING: Comparison to bool Signed-off-by:
-
Jason Yan authored
Fix the following coccicheck warning: drivers/usb/gadget/udc/net2272.c:57:12-19: WARNING: Assignment of 0/1 to bool variable Signed-off-by:
-
Jason Yan authored
Fix the following coccicheck warning: drivers/usb/dwc3/drd.c:85:3-24: WARNING: Assignment of 0/1 to bool variable drivers/usb/dwc3/drd.c:59:2-23: WARNING: Assignment of 0/1 to bool variable Signed-off-by:
-
Colin Ian King authored
The variable status is being assigned a value that is never read and it is being updated later with a new value. The assignment is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by: -
Nathan Chancellor authored
Clang warns: drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of address of 'ep->queue' equal to a null pointer is always false [-Wtautological-pointer-compare] if (&ep->queue == NULL) ~~~~^~~~~ ~~~~ 1 warning generated. It is not wrong, queue is not a pointer so if ep is not NULL, the address of queue cannot be NULL. No other driver does a check like this and this check has been around since the driver was first introduced, presumably with no issues so it does not seem like this check should be something else. Just remove it. Commit afe956c5 ("kbuild: Enable -Wtautological-compare") exposed this but it is not the root cause of the warning. Fixes: 3fc154b6 ("USB Gadget driver for Samsung s3c2410 ARM SoC") Link: https://github.com/ClangBuiltLinux/linux/issues/1004Reviewed-by:Nick Desaulniers <ndesaulniers@google.com> Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Fabrice Gasnier authored
Add suspend resume callbacks to notify u_serial of the bus suspend/resume state. Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
-
Fabrice Gasnier authored
Add suspend resume callbacks to notify u_serial of the bus suspend/resume state. Signed-off-by:
-
Fabrice Gasnier authored
Add suspend resume callbacks to handle the case seen when the bus is suspended by the HOST, and the device opens the port (cat /dev/ttyGS0). Gadget controller (like DWC2) doesn't accept usb requests to be queued in this case (when in L2 state), from the gs_open() call. Error log is printed - configfs-gadget gadget: acm ttyGS0 can't notify serial state, -11 If the HOST resumes (opens) the bus, the port still isn't functional. Use suspend/resume callbacks to monitor the gadget suspended state by using 'suspended' flag. In case the port gets opened (cat /dev/ttyGS0), the I/O stream will be delayed until the bus gets resumed by the HOST. Signed-off-by:
-
Fabrice Gasnier authored
When the remote wakeup interrupt is triggered, lx_state is resumed from L2 to L0 state. But when the gadget resume is called, lx_state is still L2. This prevents the resume callback to queue any request. Any attempt to queue a request from resume callback will result in: - "submit request only in active state" debug message to be issued - dwc2_hsotg_ep_queue() returns -EAGAIN Call the gadget resume routine after the core is in L0 state. Fixes: f81f46e1 ("usb: dwc2: implement hibernation during bus suspend/resume") Acked-by:
Minas Harutyunyan <hminas@synopsys.com> Signed-off-by:
-
Michael Grzeschik authored
This patch changes the function uvc_video_pump to be a separate scheduled worker. This way the completion handler of each usb request and every direct caller of the pump has only to schedule the worker instead of doing the request handling by itself. Moving the request handling to one thread solves the locking problems between the three queueing cases in the completion handler, v4l2_qbuf and video_enable. Many drivers handle the completion handlers directly in their interrupt handlers. This patch also reduces the workload on each interrupt. Signed-off-by:
Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by:
-
