In order to build the generic syscall table, we need a declaration for
every system call.  sys_pipe2 was added without a proper declaration, so
add this to syscalls.h now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

setup() may fail before ctldata is set, causing a kernel panic on
cleanup().
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'i2c-for-2630-rc5' of git://aeryn.fluff.org.uk/bjdooks/linux:
  i2c-cpm: Pass dev ptr to dma_*_coherent rather than NULL
  i2c: Enable i2c-s3c2410 for S3C64XX too
  i2c-mpc: bug fix for MPC52xx clock setting and printout
  i2c-pxa.c: timeouts off by 1

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: tsc2007 - fix locking in hrtimer handler
  Input: atkbd - add force release keys quirk for Amilo Xi 3650
  Input: ff-memless - fix signed to unsigned bit overflow
  Input: joydev - blacklist digitizers

Remove the return after the goto.  We want the goto because it frees
memory as well as returning err.

Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Recent DMA changes result in a BUG() when NULL is passed to
dma_alloc_coherent in place of a device.
Signed-off-by: Mark Ware <mware@elphinstone.net>
[ben-linux@fluff.org: fix patch moves]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This controller is also present on the S3C64xx series processors so
enable the driver in Kconfig for those platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The clock setting did not work for the MPC52xx due to a stupid bug.
Furthermore, the dev info output "clock=0" for old device trees was
misleading. This patch fixes both issues.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Now that hrtimers are always running in hard irq context we can't
unconditionally enable interrupts at the end of the timer function.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Adrian Batzill <agib@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

* 'for-linus' of git://repo.or.cz/cris-mirror:
  CRISv32: Fix typo compile error in ARTPEC-3 gpio driver.
  CRIS: Wire up syscalls signalfd4 to writev.
  CRISv32: Remove obsolete vcs_hook.o from Makefile
  CRIS: Merge machine dependent boot/compressed and boot/rescue

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ata_piix: The Sony TZ90 needs the cable type hardcoding
  ata_piix: ICH7 does not support correct MWDMA timings
  Avoid world-writable sysfs files in libata driver.
  libata: fix suspend/resume for ATA SEMB devices
  libata: clear ering on resume
  pata_pdc202xx_old: fix UDMA33 handling
  sata_mv: use new sata phy register settings for new devices
  libata: fix attach error handling

The return value of dup2 when oldfd == newfd and the fd isn't valid is
not getting properly sign extended.  We end up with 4294967287 instead
of -EBADF.

I've reproduced this on SLE11 (2.6.27.21), openSUSE Factory
(2.6.29-rc5), and Ubuntu 9.04 (2.6.28).

This patch uses a signed int for the error value so it is properly
extended.

Commit 6c5d0512 introduced this
regression.
Reported-by: Jiri Dluhos <jdluhos@novell.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

See Errata documentation. The recommended workaround is to use PIO4 instead
which will we automatically do by flagging this mode not available.
Signed-off-by: Alan Cox <alan.cox@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

79b42bab fixed identifying ATA devices
reporting 3c/c3 signature which belongs to SEMB devices now. However,
suspending the machine with such device (WDC WD2500AAJS-6 01.0) fails
with the following:

hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/66 mode selected
sd 1:0:0:0: [sda] Starting disk
ata5: SATA link down (SStatus 0 SControl 300)
ata1: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata2: softreset failed (device not ready)
ata2: failed due to HW bug, retry pmp=0
ata4: softreset failed (device not ready)
ata4: failed due to HW bug, retry pmp=0
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: class mismatch 1 != 7
ata2.00: revalidation failed (errno=-19)
ata2: limiting SATA link speed to 1.5 Gbps
ata4.00: configured for UDMA/133
ata2: softreset failed (device not ready)
ata2: failed due to HW bug, retry pmp=0
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: class mismatch 1 != 7
ata2.00: revalidation failed (errno=-19)
ata2.00: disabled
sd 1:0:0:0: rejecting I/O to offline device
sd 1:0:0:0: [sda] START_STOP FAILED
sd 1:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
PM: Device 1:0:0:0 failed to thaw: error 65536
sd 3:0:0:0: [sdb] Starting disk

due to a class mismatch in ata_dev_revalidate(). Fix it by adding the
ATA_DEV_SEMB device class to the check.

CC: Tejun Heo <htejun@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Error timestamps are in jiffies which doesn't run while suspended and
PHY events during resume isn't too uncommon.  When the two are
combined, it can lead to unnecessary speed downs if the machine is
suspended and resumed repeatedly.  Clear error history on resume.

This was reported and verified in bnc#486803 by Vladimir Botka.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Vladimir Botka <vbotka@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The original driver doesn't use 66 MHz clock for UDMA33.

[ The alternative solution would be to adjust UDMA33 timings
  for 66 MHz clock but I think that it is safer to stick with
  old & tested behavior for now. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Marvell's new SoC (65 nano) needs different settings for its SATA
PHY registers.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

New device attach path in ata_eh_revalidate_and_attach() is divided
into two separate loops because ATA requires IDENTIFY to be issued to
slave first while the user expects to see device probe messages from
the master device.  new_mask is used to track which devices are the
new ones between the first loop and the second.

This usually works well but if an error occurs during configuration
stage, ata_dev_revalidate_and_attach() returns with error code and
forgets new_mask.  On the retry run, dev->class is set and new_mask
for the device is clear, so the device just gets revalidated and thus
ends up skipping post-configuration procedure including scheduling of
SCSI_HOTPLUG for the device.  When this occurs, ATA part of probing
works fine but SCSI probing usually doesn't happen and makes the
device unreachable.

The behavior has been around for a very long time but it has been
uncovered with the recent addition of 1_5_GBPS horkage which uses
-EAGAIN return value from ata_dev_configure() to restart the probing
sequence after forcing cable speed.

This can be fixed by making sure dev->class is permanently set only
after all configurations are successfully complete.  Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tim Connors <tconnors+linuxkml@astro.swin.edu.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

PAGE_MASK is 0xFFFFF000 on i386 -- even with PAE.

So it's not sufficient to ensure that you use phys_addr_t or uint64_t
everywhere you handle physical addresses -- you also have to avoid using
the construct 'addr & PAGE_MASK', because that will strip the high 32
bits of the address.

This patch avoids that problem by using PHYSICAL_PAGE_MASK instead of
PAGE_MASK where appropriate. It leaves '& PAGE_MASK' in a few instances
that don't matter -- where it's being used on the virtual bus addresses
we're dishing out, which are 32-bit anyway.

Since PHYSICAL_PAGE_MASK is not present on other architectures, we have
to define it (to PAGE_MASK) if it's not already defined.

Maybe it would be better just to fix PAGE_MASK for i386/PAE?
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: comedi: David doesn't want to get comedi patches
  Staging: rtl8187se: Fix compilation warnings and procfs directory leak
  Staging: rt2870: new device id
  Staging: w35und: unregister device from the ieee80211 stack upon ->disconnect()

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  usb-serial: ftdi_sio: fix reference counting of ftdi_private
  USB: unusual_devs: extend nokia 6288 bcd range
  USB: Gadget: fix UTF conversion in the usbstring library
  USB: Fix makefile so that CONFIG_WDM and CONFIG_TMC work.
  USB: ftdi_sio: add vendor/product id for the Marvell SheevaPlug
  USB: cxacru: Fix negative dB output

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  Revert driver core: move platform_data into platform_device
  Revert driver core: fix passing platform_data
  Remove old PRINTK_DEBUG config item
  Doc/sysfs-rules: Swap the order of the words so the sentence makes more sense
  Driver core: platform: fix kernel-doc warnings

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (22 commits)
  Fix the race between capifs remount and node creation
  Fix races around the access to ->s_options
  switch ufs directories to ufs_sync_file()
  Switch open_exec() and sys_uselib() to do_open_filp()
  Make open_exec() and sys_uselib() use may_open(), instead of duplicating its parts
  Reduce path_lookup() abuses
  Make checkpatch.pl shut up on fs/inode.c
  NULL noise in fs/super.c:kill_bdev_super()
  romfs: cleanup romfs_fs.h
  ROMFS: romfs_dev_read() error ignored
  fs: dcache fix LRU ordering
  ocfs2: Use nd_set_link().
  Fix deadlock in ipathfs ->get_sb()
  Fix a leak in failure exit in 9p ->get_sb()
  Convert obvious places to deactivate_locked_super()
  New helper: deactivate_locked_super()
  reiserfs: remove privroot hiding in lookup
  reiserfs: dont associate security.* with xattr files
  reiserfs: fixup xattr_root caching
  Always lookup priv_root on reiserfs mount and keep it
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  GFS2: Fix glock ref counting bug

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix line-in on Mac Mini Core2 Duo
  ALSA: Release v1.0.20
  sound: via82xx: fix DXS volume range
  sound: serial-u16550: fix buffer overflow
  ASoC: Fix errors in WM8990

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB (11680): cafe_ccic: use = instead of == for setting a value at a var
  V4L/DVB (11679): cafe_ccic: fix sensor detection
  V4L/DVB (11675): ivtv/radio: fix V4L2_TUNER_MODE/V4L2_TUNER_SUB confusion
  V4L/DVB (11674): ivtv: fix incorrect bit tests
  V4L/DVB (11669): uvc: fix compile warning
  V4L/DVB (11668): ivtv: fix compiler warning.
  V4L/DVB (11664): cx23885: Frontend wasn't locking on HVR-1500
  V4L/DVB (11662): v4l2-ioctl: Clear buffer type specific trailing fields/padding
  V4L/DVB (11661): v4l2-ioctl: Check buffer types using g_fmt instead of try_fmt
  V4L/DVB (11660): zoran: fix bug when enumerating format -1
  V4L/DVB (11575): uvcvideo: fix uvc resume failed

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
  bonding: fix panic if initialization fails
  IXP4xx: complete Ethernet netdev setup before calling register_netdev().
  IXP4xx: use "ENODEV" instead of "ENOSYS" in module initialization.
  ipvs: Fix IPv4 FWMARK virtual services
  ipv4: Make INET_LRO a bool instead of tristate.
  net: remove stale reference to fastroute from Kconfig help text
  net: update skb_recycle_check() for hardware timestamping changes
  bnx2: Fix panic in bnx2_poll_work().
  net-sched: fix bfifo default limit
  igb: resolve panic on shutdown when SR-IOV is enabled
  wimax: oops: wimax_dev_add() is the only one that can initialize the state
  wimax: fix oops if netlink fails to add attribute
  Bluetooth: Move dev_set_name() to a context that can sleep
  netfilter: ctnetlink: fix wrong message type in user updates
  netfilter: xt_cluster: fix use of cluster match with 32 nodes
  netfilter: ip6t_ipv6header: fix match on packets ending with NEXTHDR_NONE
  netfilter: add missing linux/types.h include to xt_LED.h
  mac80211: pid, fix memory corruption
  mac80211: minstrel, fix memory corruption
  cfg80211: fix comment on regulatory hint processing
  ...

* fix/asoc:
  ASoC: Fix errors in WM8990

* fix/hda:
  ALSA: hda - Fix line-in on Mac Mini Core2 Duo

* topic/misc:
  ALSA: Release v1.0.20

* fix/misc:
  sound: via82xx: fix DXS volume range
  sound: serial-u16550: fix buffer overflow

/home/v4l/master/v4l/cafe_ccic.c: In function 'cafe_cam_init':
/home/v4l/master/v4l/cafe_ccic.c:778: warning: statement with no effect

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: saeed bishara <saeed.bishara@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Due to an uninitialized chip.ident field the chip identification failed.

Thanks-to: Saeed Bishara <saeed.bishara@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L2_TUNER_MODE_ was used in a few places where V4L2_TUNER_SUB_ should have
been used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Found the coccinelle tool.

Thanks-to: Julia Lawall <julia@diku.dk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The 2.6.30 kernel generates this warning:

uvc_driver.c:1729: warning: 'ret' may be used uninitialized in this function

I guess some new warning flag must have been turned on since this warning
didn't appear with older kernels (gcc version 4.3.1). It's also a bogus
warning, but since this code didn't comply to the coding standard anyway
I've modified it to 1) remove the warning and 2) conform to the coding
standard.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>