The update of stream costs significantly, and we should avoid it
unless the stream really has started.  Check pipe->running flag
instead of pipe->prepared.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The pseudo DMA transfer codes in VX222 and VX-pocket driver have a
slight bug where they check the buffer boundary wrongly, and may
overflow.  Also, the zero sample count might be handled badly for the
playback (although it shouldn't happen in theory).  This patch
addresses these issues.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=141541Signed-off-by: Takashi Iwai <tiwai@suse.de>

Imre Deak reported a deadlock of HD-audio driver at unbinding while
it's still in probing.  Since we probe the codecs asynchronously in a
work, the codec driver probe may still be kicked off while the
controller itself is being unbound.  And, azx_remove() tries to
process all pending tasks via cancel_work_sync() for fixing the other
races (see commit [0b8c8219: ALSA: hda - Cancel probe work instead
of flush at remove]), now we may meet a bizarre deadlock:

Unbind snd_hda_intel via sysfs:
  device_release_driver() ->
    device_lock(snd_hda_intel) ->
      azx_remove() ->
        cancel_work_sync(azx_probe_work)

azx_probe_work():
  codec driver probe() ->
     __driver_attach() ->
       device_lock(snd_hda_intel)

This deadlock is caused by the fact that both device_release_driver()
and driver_probe_device() take both the device and its parent locks at
the same time.  The codec device sets the controller device as its
parent, and this lock is taken before the probe() callback is called,
while the controller remove() callback gets called also with the same
lock.

In this patch, as an ugly workaround, we unlock the controller device
temporarily during cancel_work_sync() call.  The race against another
bind call should be still suppressed by the parent's device lock.
Reported-by: Imre Deak <imre.deak@intel.com>
Fixes: 0b8c8219 ("ALSA: hda - Cancel probe work instead of flush at remove")
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALC299 was similar as ALC225.
Add headset support for ALC299.
ALC3271 was for Dell rename.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

As of kernel 4.10, ALSA dice driver is expected to be used in default
speed. In most cases, it's S400. While, IEEE 1394 specification describes
the other speed such as S800.

According to 'TCD30XX User Guide', its link layer controller supports
several transmission speed up to S800[0]. In Dice software interface,
transmission speed in output direction can be configured by asynchronous
transaction to 'TX_SPEED' offset in its address space. S800 may be
available.

This commit improves configuration of transmission unit before starting
packet streaming for this purpose. The value of 'max_speed' in 'fw_device'
data structure has available maximum speed decided in bus arbitration,
thus it's within capacity of the unit.

[0] TCD3xx User Guide - TCAT 1394 LLC, Revision 0.9.0-41360 (TC Applied Technologies, May 6 2015)
http://www.tctechnologies.tc/index.php/support/support-hardware/dice-iii-detailed-documentationSigned-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The 'amdtp_stream' structure is initialized by a call of
'amdtp_stream_init()'. Although a parameter of this function is for bit
flags of packet attributes, its type is enumerator.

This commit changes the type so that it's proper for a bit flags.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This module has a bug not to return error code in a case that data
structure for transmitted packets fails to be initialized.

This commit fixes the bug.

Fixes: 35efa5c4 ("ALSA: firewire-tascam: add streaming functionality")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA fireworks driver has a bug not to call an API to destroy
'cmp_connection' structure for input direction. Currently this causes no
issues because it just destroys 'mutex' structure, while it's better to
fix it for future work.

Fix: d23c2cc4 ("ALSA: fireworks/bebob/dice/oxfw: allow stream destructor after releasing runtime")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

As of kernel 4.10,  ALSA OXFW driver has no entry for Onyx 1640i produced
by Mackie (Loud Technologies). This commit supplement it.

I note that there're two models produced by Mackie (Loud Technologies),
which have the same name 'Onyx 1640i'. The former model based on OXFW970,
the latter model based on Dice. This is probably due to low quality of
communication of OXFW series.

Additionally, the tester reports his or her experiences to get unexpected
result at higher sampling transmission frequency as 88.2/96.0 kHz. We
didn't have further investigation yet[0].

$ ./linux-firewire-utils/src/crpp < config_rom
               ROM header and bus information block
               -----------------------------------------------------------------
400  042525ce  bus_info_length 4, crc_length 37, crc 9678
404  31333934  bus_name "1394"
408  20ff5003  irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 5 (64)
40c  000ff205  company_id 000ff2     |
410  00000fcf  device_id 0500000fcf  | EUI-64 000ff20500000fcf

               root directory
               -----------------------------------------------------------------
414  0006c1b7  directory_length 6, crc 49591
418  03000ff2  vendor
41c  8100000a  --> descriptor leaf at 444
420  17001640  model
424  81000011  --> descriptor leaf at 468
428  0c0083c0  node capabilities per IEEE 1394
42c  d1000001  --> unit directory at 430

               unit directory at 430
               -----------------------------------------------------------------
430  00040b97  directory_length 4, crc 2967
434  1200a02d  specifier id: 1394 TA
438  13010001  version: AV/C
43c  17001640  model
440  81000010  --> descriptor leaf at 480

               descriptor leaf at 444
               -----------------------------------------------------------------
444  0008a886  leaf_length 8, crc 43142
448  00000000  textual descriptor
44c  00000000  minimal ASCII
450  4c6f7564  "Loud"
454  20546563  " Tec"
458  686e6f6c  "hnol"
45c  6f676965  "ogie"
460  7320496e  "s In"
464  632e0000  "c."

               descriptor leaf at 468
               -----------------------------------------------------------------
468  00059fcf  leaf_length 5, crc 40911
46c  00000000  textual descriptor
470  00000000  minimal ASCII
474  4f6e7978  "Onyx"
478  20313634  " 164"
47c  30690000  "0i"

               descriptor leaf at 480
               -----------------------------------------------------------------
480  00059fcf  leaf_length 5, crc 40911
484  00000000  textual descriptor
488  00000000  minimal ASCII
48c  4f6e7978  "Onyx"
490  20313634  " 164"
494  30690000  "0i"

[0]: [FFADO-user] Mackie 1640i issues (finer details)
https://sourceforge.net/p/ffado/mailman/message/35229260/Tested-by: Seth O'Bannion <saobannion@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull DAX updates from Dan Williams:
 "The completion of Jan's DAX work for 4.10.

  As I mentioned in the libnvdimm-for-4.10 pull request, these are some
  final fixes for the DAX dirty-cacheline-tracking invalidation work
  that was merged through the -mm, ext4, and xfs trees in -rc1. These
  patches were prepared prior to the merge window, but we waited for
  4.10-rc1 to have a stable merge base after all the prerequisites were
  merged.

  Quoting Jan on the overall changes in these patches:

     "So I'd like all these 6 patches to go for rc2. The first three
      patches fix invalidation of exceptional DAX entries (a bug which
      is there for a long time) - without these patches data loss can
      occur on power failure even though user called fsync(2). The other
      three patches change locking of DAX faults so that ->iomap_begin()
      is called in a more relaxed locking context and we are safe to
      start a transaction there for ext4"

  These have received a build success notification from the kbuild
  robot, and pass the latest libnvdimm unit tests. There have not been
  any -next releases since -rc1, so they have not appeared there"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  ext4: Simplify DAX fault path
  dax: Call ->iomap_begin without entry lock during dax fault
  dax: Finish fault completely when loading holes
  dax: Avoid page invalidation races and unnecessary radix tree traversals
  mm: Invalidate DAX radix tree entries only if appropriate
  ext2: Return BH_New buffers for zeroed blocks

Pull documentation fixes from Jonathan Corbet:
 "Two small fixes:

   - A merge error on my part broke the DocBook build. I've
     requisitioned one of tglx's frozen sharks for appropriate
     disciplinary action and resolved to be more careful about testing
     the DocBook stuff as long as it's still around.

   - Fix an error in unaligned-memory-access.txt"

* tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux:
  Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
  docs: Fix build failure

Pull crypto fix from Herbert Xu:
 "This fixes a boot failure on some platforms when crypto self test is
  enabled along with the new acomp interface"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: testmgr - Use heap buffer for acomp test input

 mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
  mm/filemap.c:933:9: error: too few arguments to function 'test_bit'
    return test_bit(PG_waiters);
         ^~~~~~~~

Fixes: b91e1302 ('mm: optimize PageWaiters bit use for unlock_page()')
Signed-off-by: Olof Johansson <olof@lixom.net>
Brown-paper-bag-by: Linus Torvalds <dummy@duh.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In commit 62906027 ("mm: add PageWaiters indicating tasks are
waiting for a page bit") Nick Piggin made our page locking no longer
unconditionally touch the hashed page waitqueue, which not only helps
performance in general, but is particularly helpful on NUMA machines
where the hashed wait queues can bounce around a lot.

However, the "clear lock bit atomically and then test the waiters bit"
sequence turns out to be much more expensive than it needs to be,
because you get a nasty stall when trying to access the same word that
just got updated atomically.

On architectures where locking is done with LL/SC, this would be trivial
to fix with a new primitive that clears one bit and tests another
atomically, but that ends up not working on x86, where the only atomic
operations that return the result end up being cmpxchg and xadd.  The
atomic bit operations return the old value of the same bit we changed,
not the value of an unrelated bit.

On x86, we could put the lock bit in the high bit of the byte, and use
"xadd" with that bit (where the overflow ends up not touching other
bits), and look at the other bits of the result.  However, an even
simpler model is to just use a regular atomic "and" to clear the lock
bit, and then the sign bit in eflags will indicate the resulting state
of the unrelated bit #7.

So by moving the PageWaiters bit up to bit #7, we can atomically clear
the lock bit and test the waiters bit on x86 too.  And architectures
with LL/SC (which is all the usual RISC suspects), the particular bit
doesn't matter, so they are fine with this approach too.

This avoids the extra access to the same atomic word, and thus avoids
the costly stall at page unlock time.

The only downside is that the interface ends up being a bit odd and
specialized: clear a bit in a byte, and test the sign bit.  Nick doesn't
love the resulting name of the new primitive, but I'd rather make the
name be descriptive and very clear about the limitation imposed by
trying to work across all relevant architectures than make it be some
generic thing that doesn't make the odd semantics explicit.

So this introduces the new architecture primitive

    clear_bit_unlock_is_negative_byte();

and adds the trivial implementation for x86.  We have a generic
non-optimized fallback (that just does a "clear_bit()"+"test_bit(7)"
combination) which can be overridden by any architecture that can do
better.  According to Nick, Power has the same hickup x86 has, for
example, but some other architectures may not even care.

All these optimizations mean that my page locking stress-test (which is
just executing a lot of small short-lived shell scripts: "make test" in
the git source tree) no longer makes our page locking look horribly bad.
Before all these optimizations, just the unlock_page() costs were just
over 3% of all CPU overhead on "make test".  After this, it's down to
0.66%, so just a quarter of the cost it used to be.

(The difference on NUMA is bigger, but there this micro-optimization is
likely less noticeable, since the big issue on NUMA was not the accesses
to 'struct page', but the waitqueue accesses that were already removed
by Nick's earlier commit).
Acked-by: Nick Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The Samsung Ativ Book 8 makes a loud click noise on boot, shutdown
and when the audio card enters or exits power saving states. All
these noises disappear applying ALC269_FIXUP_NO_SHUTUP.

In addition to that, fix the loud click noise that the laptop
makes when inserting or removing the headphone jack by automuting
via amp instead of pinctl.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Setting shutup when the action is HDA_FIXUP_ACT_PRE_PROBE might
not have the desired effect since it could be overridden by
another more generic shutup function. Prevent this by setting
the more specific shutup function on HDA_FIXUP_ACT_PROBE.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fix a comment typo in mixart.h.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add DSD support for both little endian (DSD_U32_LE) and big endian
(DSD_U32_BE) version of the Amanero firmware.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When CONFIG_PM_SLEEP is disabled, SIMPLE_DEV_PM_OPS does not use
snd_cs5535audio_resume and snd_cs5535audio_suspend functions:

sound/pci/cs5535audio/cs5535audio_pm.c:77:12: warning: ‘snd_cs5535audio_resume’ defined but not used [-Wunused-function]
 static int snd_cs5535audio_resume(struct device *dev)
            ^~~~~~~~~~~~~~~~~~~~~~
sound/pci/cs5535audio/cs5535audio_pm.c:58:12: warning: ‘snd_cs5535audio_suspend’ defined but not used [-Wunused-function]
 static int snd_cs5535audio_suspend(struct device *dev)
            ^~~~~~~~~~~~~~~~~~~~~~~

Adding __maybe_unused to the declaration of these functions removes the
warnings.
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull crypto fix from Herbert Xu:
 "This fixes a hash corruption bug in the marvell driver"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: marvell - Copy IVDIG before launching partial DMA ahash requests

Pull networking fixes from David Miller:

 1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.

    The most important is to not assume the packet is RX just because
    the destination address matches that of the device. Such an
    assumption causes problems when an interface is put into loopback
    mode.

 2) If we retry when creating a new tc entry (because we dropped the
    RTNL mutex in order to load a module, for example) we end up with
    -EAGAIN and then loop trying to replay the request. But we didn't
    reset some state when looping back to the top like this, and if
    another thread meanwhile inserted the same tc entry we were trying
    to, we re-link it creating an enless loop in the tc chain. Fix from
    Daniel Borkmann.

 3) There are two different WRITE bits in the MDIO address register for
    the stmmac chip, depending upon the chip variant. Due to a bug we
    could set them both, fix from Hock Leong Kweh.

 4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: stmmac: fix incorrect bit set in gmac4 mdio addr register
  r8169: add support for RTL8168 series add-on card.
  net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
  openvswitch: upcall: Fix vlan handling.
  ipv4: Namespaceify tcp_tw_reuse knob
  net: korina: Fix NAPI versus resources freeing
  net, sched: fix soft lockup in tc_classify
  net/mlx4_en: Fix user prio field in XDP forward
  tipc: don't send FIN message from connectionless socket
  ipvlan: fix multicast processing
  ipvlan: fix various issues in ipvlan_process_multicast()

In the actual implementation ether_addr_equal function tests for equality to 0
when returning. It seems in commit 0d74c4 it is somehow overlooked to change
this operator to reflect the actual function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

The 80211.tmpl DocBook file was removed in commit 819bf593 ("docs-rst:
sphinxify 802.11 documentation"), but the 80211.xml target was re-added to
the Makefile by commit 7ddedebb ("ALSA: doc: ReSTize
writing-an-alsa-driver document"), leading to a failure when building the
documentation:

*** No rule to make target 'Documentation/DocBook/80211.xml', needed by
'Documentation/DocBook/80211.aux.xml'.

cc: stable@vger.kernel.org
Signed-off-by: John Brooks <john@fastquake.com>
Mea-culpa-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Linux 4.10-rc1

Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 73b62bd0 ("virtio-net:
remove the warning before XDP linearizing"), there's no users for
bpf_warn_invalid_xdp_buffer(), so remove it. This is a revert for
commit f23bc46c.

Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Networking stack accelerate vlan tag handling by
keeping topmost vlan header in skb. This works as
long as packet remains in OVS datapath. But during
OVS upcall vlan header is pushed on to the packet.
When such packet is sent back to OVS datapath, core
networking stack might not handle it correctly. Following
patch avoids this issue by accelerating the vlan tag
during flow key extract. This simplifies datapath by
bringing uniform packet processing for packets from
all code paths.

Fixes: 5108bbad ("openvswitch: add processing of L3 packets").
CC: Jarno Rajahalme <jarno@ovn.org>
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Christopher Covington reported a crash on aarch64 on recent Fedora
kernels:

kernel BUG at ./include/linux/scatterlist.h:140!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 752 Comm: cryptomgr_test Not tainted 4.9.0-11815-ge93b1cc8 #162
Hardware name: linux,dummy-virt (DT)
task: ffff80007c650080 task.stack: ffff800008910000
PC is at sg_init_one+0xa0/0xb8
LR is at sg_init_one+0x24/0xb8
...
[<ffff000008398db8>] sg_init_one+0xa0/0xb8
[<ffff000008350a44>] test_acomp+0x10c/0x438
[<ffff000008350e20>] alg_test_comp+0xb0/0x118
[<ffff00000834f28c>] alg_test+0x17c/0x2f0
[<ffff00000834c6a4>] cryptomgr_test+0x44/0x50
[<ffff0000080dac70>] kthread+0xf8/0x128
[<ffff000008082ec0>] ret_from_fork+0x10/0x50

The test vectors used for input are part of the kernel image. These
inputs are passed as a buffer to sg_init_one which eventually blows up
with BUG_ON(!virt_addr_valid(buf)). On arm64, virt_addr_valid returns
false for the kernel image since virt_to_page will not return the
correct page. Fix this by copying the input vectors to heap buffer
before setting up the scatterlist.
Reported-by: Christopher Covington <cov@codeaurora.org>
Fixes: d7db7a88 ("crypto: acomp - update testmgr with support for acomp")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Now that dax_iomap_fault() calls ->iomap_begin() without entry lock, we
can use transaction starting in ext4_iomap_begin() and thus simplify
ext4_dax_fault(). It also provides us proper retries in case of ENOSPC.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Currently ->iomap_begin() handler is called with entry lock held. If the
filesystem held any locks between ->iomap_begin() and ->iomap_end()
(such as ext4 which will want to hold transaction open), this would cause
lock inversion with the iomap_apply() from standard IO path which first
calls ->iomap_begin() and only then calls ->actor() callback which grabs
entry locks for DAX (if it faults when copying from/to user provided
buffers).

Fix the problem by nesting grabbing of entry lock inside ->iomap_begin()
- ->iomap_end() pair.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

The only case when we do not finish the page fault completely is when we
are loading hole pages into a radix tree. Avoid this special case and
finish the fault in that case as well inside the DAX fault handler. It
will allow us for easier iomap handling.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Currently dax_iomap_rw() takes care of invalidating page tables and
evicting hole pages from the radix tree when write(2) to the file
happens. This invalidation is only necessary when there is some block
allocation resulting from write(2). Furthermore in current place the
invalidation is racy wrt page fault instantiating a hole page just after
we have invalidated it.

So perform the page invalidation inside dax_iomap_actor() where we can
do it only when really necessary and after blocks have been allocated so
nobody will be instantiating new hole pages anymore.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Currently invalidate_inode_pages2_range() and invalidate_mapping_pages()
just delete all exceptional radix tree entries they find. For DAX this
is not desirable as we track cache dirtiness in these entries and when
they are evicted, we may not flush caches although it is necessary. This
can for example manifest when we write to the same block both via mmap
and via write(2) (to different offsets) and fsync(2) then does not
properly flush CPU caches when modification via write(2) was the last
one.

Create appropriate DAX functions to handle invalidation of DAX entries
for invalidate_inode_pages2_range() and invalidate_mapping_pages() and
wire them up into the corresponding mm functions.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

So far we did not return BH_New buffers from ext2_get_blocks() when we
allocated and zeroed-out a block for DAX inode to avoid racy zeroing in
DAX code. This zeroing is gone these days so we can remove the
workaround.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

If mce_device_init() fails then the mce device pointer is NULL and the
AMD mce code happily dereferences it.

Add a sanity check.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>