- 18 Aug, 2016 12 commits
-
-
Mika Westerberg authored
BugLink: http://bugs.launchpad.net/bugs/1614560 commit a7ae8195 upstream. Many Intel systems the BIOS declares a SystemIO OpRegion below the SMBus PCI device as can be seen in ACPI DSDT table from Lenovo Yoga 900: Device (SBUS) { OperationRegion (SMBI, SystemIO, (SBAR << 0x05), 0x10) Field (SMBI, ByteAcc, NoLock, Preserve) { HSTS, 8, Offset (0x02), HCON, 8, HCOM, 8, TXSA, 8, DAT0, 8, DAT1, 8, HBDR, 8, PECR, 8, RXSA, 8, SDAT, 16 } There are also bunch of AML methods that that the BIOS can use to access these fields. Most of the systems in question AML methods accessing the SMBI OpRegion are never used. Now, because of this SMBI OpRegion many systems fail to load the SMBus driver with an error looking like one below: ACPI Warning: SystemIO range 0x0000000000003040-0x000000000000305F conflicts with OpRegion 0x0000000000003040-0x000000000000304F (\_SB.PCI0.SBUS.SMBI) (20160108/utaddress-255) ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver The reason is that this SMBI OpRegion conflicts with the PCI BAR used by the SMBus driver. It turns out that we can install a custom SystemIO address space handler for the SMBus device to intercept all accesses through that OpRegion. This allows us to share the PCI BAR with the AML code if it for some reason is using it. We do not expect that this OpRegion handler will ever be called but if it is we print a warning and prevent all access from the SMBus driver itself. Link: https://bugzilla.kernel.org/show_bug.cgi?id=110041Reported-by:
Andy Lutomirski <luto@kernel.org> Reported-by:
Pali Rohár <pali.rohar@gmail.com> Suggested-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by:
Jean Delvare <jdelvare@suse.de> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Tested-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Tim Gardner <tim.gardner@canonical.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Benjamin Tissoires authored
BugLink: http://bugs.launchpad.net/bugs/1614560 commit 19f4c2ba upstream. When setting the operational mode, some third party (Speedlink Strike-FX) gamepads refuse the output report. Failing here means we refuse to initialize the gamepad while this should be harmless. The weird part is that the initial commit that added this: a7de9b86 ("HID: sony: Enable Gasia third-party PS3 controllers") mentions this very same controller as one requiring this output report. Anyway, it's broken for one user at least, so let's change it. We will report an error, but at least the controller should work. And no, these devices present themselves as legacy Sony controllers (VID:PID of 054C:0268, as in the official ones) so there are no ways of discriminating them from the official ones. https://bugzilla.redhat.com/show_bug.cgi?id=1255325Reported-and-tested-by:
Max Fedotov <thesourcehim@gmail.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Cc: Laura Abbott <labbott@redhat.com> Signed-off-by:
-
Hannes Reinecke authored
BugLink: http://bugs.launchpad.net/bugs/1614560 commit 221255ae upstream. device handler initialisation might fail due to a number of reasons. But as device_handlers are optional this shouldn't cause us to disable the device entirely. So just ignore errors from scsi_dh_add_device(). Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Cc: Laura Abbott <labbott@redhat.com> Signed-off-by:
-
Ben Hutchings authored
BugLink: http://bugs.launchpad.net/bugs/1614560 Commit e6bd18f5 ("IB/security: Restrict use of the write() interface") fixed a security problem with various write() implementations in the Infiniband subsystem. In older kernel versions the ipath_write() function has the same problem and needs the same restriction. (The ipath driver has been completely removed upstream.) Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Soheil Hassas Yeganeh authored
BugLink: http://bugs.launchpad.net/bugs/1614560 [ Upstream commit f626300a ] tcp_select_initial_window() intends to advertise a window scaling for the maximum possible window size. To do so, it considers the maximum of net.ipv4.tcp_rmem[2] and net.core.rmem_max as the only possible upper-bounds. However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE to set the socket's receive buffer size to values larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max. Thus, SO_RCVBUFFORCE is effectively ignored by tcp_select_initial_window(). To fix this, consider the maximum of net.ipv4.tcp_rmem[2], net.core.rmem_max and socket's initial buffer space. Fixes: b0573dea ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options") Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Suggested-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Manish Chopra authored
BugLink: http://bugs.launchpad.net/bugs/1614560 [ Upstream commit 59d3f1ce ] Slowpath completion handling is incorrectly changing SPQ_RING_SIZE bits instead of a single one. Fixes: 76a9a364 ("qed: fix handling of concurrent ramrods") Signed-off-by:
Manish Chopra <manish.chopra@qlogic.com> Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
-
Vegard Nossum authored
BugLink: http://bugs.launchpad.net/bugs/1614560 [ Upstream commit d3e6952c ] I ran into this: kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN CPU: 2 PID: 2012 Comm: trinity-c3 Not tainted 4.7.0-rc7+ #19 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014 task: ffff8800b745f2c0 ti: ffff880111740000 task.ti: ffff880111740000 RIP: 0010:[<ffffffff82bbf066>] [<ffffffff82bbf066>] irttp_connect_request+0x36/0x710 RSP: 0018:ffff880111747bb8 EFLAGS: 00010286 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000069dd8358 RDX: 0000000000000009 RSI: 0000000000000027 RDI: 0000000000000048 RBP: ffff880111747c00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000069dd8358 R11: 1ffffffff0759723 R12: 0000000000000000 R13: ffff88011a7e4780 R14: 0000000000000027 R15: 0000000000000000 FS: 00007fc738404700(0000) GS:ffff88011af00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc737fdfb10 CR3: 0000000118087000 CR4: 00000000000006e0 Stack: 0000000000000200 ffff880111747bd8 ffffffff810ee611 ffff880119f1f220 ffff880119f1f4f8 ffff880119f1f4f0 ffff88011a7e4780 ffff880119f1f232 ffff880119f1f220 ffff880111747d58 ffffffff82bca542 0000000000000000 Call Trace: [<ffffffff82bca542>] irda_connect+0x562/0x1190 [<ffffffff825ae582>] SYSC_connect+0x202/0x2a0 [<ffffffff825b4489>] SyS_connect+0x9/0x10 [<ffffffff8100334c>] do_syscall_64+0x19c/0x410 [<ffffffff83295ca5>] entry_SYSCALL64_slow_path+0x25/0x25 Code: 41 89 ca 48 89 e5 41 57 41 56 41 55 41 54 41 89 d7 53 48 89 fb 48 83 c7 48 48 89 fa 41 89 f6 48 c1 ea 03 48 83 ec 20 4c 8b 65 10 <0f> b6 04 02 84 c0 74 08 84 c0 0f 8e 4c 04 00 00 80 7b 48 00 74 RIP [<ffffffff82bbf066>] irttp_connect_request+0x36/0x710 RSP <ffff880111747bb8> ---[ end trace 4cda2588bc055b30 ]--- The problem is that irda_open_tsap() can fail and leave self->tsap = NULL, and then irttp_connect_request() almost immediately dereferences it. Cc: stable@vger.kernel.org Signed-off-by:
Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
-
Florian Fainelli authored
BugLink: http://bugs.launchpad.net/bugs/1614560 [ Upstream commit e86663c4 ] Nothing is decrementing the index "i" while we are cleaning up the fragments we could not successful transmit. Fixes: 9cde9450 ("bgmac: implement scatter/gather support") Reported-by: coverity (CID 1352048) Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Beniamino Galvani authored
BugLink: http://bugs.launchpad.net/bugs/1614560 [ Upstream commit 005db31d ] Commit e826eafa ("bonding: Call netif_carrier_off after register_netdevice") moved netif_carrier_off() from bond_init() to bond_create(), but the latter is called only for initial default devices and ones created through sysfs: $ modprobe bonding $ echo +bond1 > /sys/class/net/bonding_masters $ ip link add bond2 type bond $ grep "MII Status" /proc/net/bonding/* /proc/net/bonding/bond0:MII Status: down /proc/net/bonding/bond1:MII Status: down /proc/net/bonding/bond2:MII Status: up Ensure that carrier is initially off also for devices created through netlink. Signed-off-by:
Beniamino Galvani <bgalvani@redhat.com> Signed-off-by:
-
Julian Anastasov authored
BugLink: http://bugs.launchpad.net/bugs/1614560 [ Upstream commit 80610229 ] Vegard Nossum is reporting for a crash in fib_dump_info when nh_dev = NULL and fib_nhs == 1: Pid: 50, comm: netlink.exe Not tainted 4.7.0-rc5+ RIP: 0033:[<00000000602b3d18>] RSP: 0000000062623890 EFLAGS: 00010202 RAX: 0000000000000000 RBX: 000000006261b800 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000024 RDI: 000000006245ba00 RBP: 00000000626238f0 R08: 000000000000029c R09: 0000000000000000 R10: 0000000062468038 R11: 000000006245ba00 R12: 000000006245ba00 R13: 00000000625f96c0 R14: 00000000601e16f0 R15: 0000000000000000 Kernel panic - not syncing: Kernel mode fault at addr 0x2e0, ip 0x602b3d18 CPU: 0 PID: 50 Comm: netlink.exe Not tainted 4.7.0-rc5+ #581 Stack: 626238f0 960226a02 00000400 000000fe 62623910 600afca7 62623970 62623a48 62468038 00000018 00000000 00000000 Call Trace: [<602b3e93>] rtmsg_fib+0xd3/0x190 [<602b6680>] fib_table_insert+0x260/0x500 [<602b0e5d>] inet_rtm_newroute+0x4d/0x60 [<60250def>] rtnetlink_rcv_msg+0x8f/0x270 [<60267079>] netlink_rcv_skb+0xc9/0xe0 [<60250d4b>] rtnetlink_rcv+0x3b/0x50 [<60265400>] netlink_unicast+0x1a0/0x2c0 [<60265e47>] netlink_sendmsg+0x3f7/0x470 [<6021dc9a>] sock_sendmsg+0x3a/0x90 [<6021e0d0>] ___sys_sendmsg+0x300/0x360 [<6021fa64>] __sys_sendmsg+0x54/0xa0 [<6021fac0>] SyS_sendmsg+0x10/0x20 [<6001ea68>] handle_syscall+0x88/0x90 [<600295fd>] userspace+0x3fd/0x500 [<6001ac55>] fork_handler+0x85/0x90 $ addr2line -e vmlinux -i 0x602b3d18 include/linux/inetdevice.h:222 net/ipv4/fib_semantics.c:1264 Problem happens when RTNH_F_LINKDOWN is provided from user space when creating routes that do not use the flag, catched with netlink fuzzer. Currently, the kernel allows user space to set both flags to nh_flags and fib_flags but this is not intentional, the assumption was that they are not set. Fix this by rejecting both flags with EINVAL. Reported-by:
Julian Anastasov <ja@ssi.bg> Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Cc: Dinesh Dutt <ddutt@cumulusnetworks.com> Cc: Scott Feldman <sfeldma@gmail.com> Reviewed-by:
Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by:
-
Jason Baron authored
BugLink: http://bugs.launchpad.net/bugs/1614560 [ Upstream commit 083ae308 ] The per-socket rate limit for 'challenge acks' was introduced in the context of limiting ack loops: commit f2b2c582 ("tcp: mitigate ACK loops for connections as tcp_sock") And I think it can be extended to rate limit all 'challenge acks' on a per-socket basis. Since we have the global tcp_challenge_ack_limit, this patch allows for tcp_challenge_ack_limit to be set to a large value and effectively rely on the per-socket limit, or set tcp_challenge_ack_limit to a lower value and still prevents a single connections from consuming the entire challenge ack quota. It further moves in the direction of eliminating the global limit at some point, as Eric Dumazet has suggested. This a follow-up to: Subject: tcp: make challenge acks less predictable Cc: Eric Dumazet <edumazet@google.com> Cc: David S. Miller <davem@davemloft.net> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Yue Cao <ycao009@ucr.edu> Signed-off-by:
Jason Baron <jbaron@akamai.com> Signed-off-by:
-
Sukadev Bhattiprolu authored
BugLink: http://bugs.launchpad.net/bugs/1614309 When trying to boot large kernel and initrd images on large systems (with hundreds of CPUs and Terabytes of memory), we sometimes run out of memory for the flattened device tree (FDT). Increase the memory allocated for the Real Mode Area (RMA) to 512MB to allow more room for the FDT. Signed-off-by:
Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com> Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
- 16 Aug, 2016 4 commits
-
-
Wen-chien Jesse Sung authored
BugLink: https://launchpad.net/bugs/1512999 For Edge Gateway 5000/5100 only. Add code for controlling bluetooth LED via firmware, and turns the LED on and off when the interface is up and down accordingly. Signed-off-by:
Wen-chien Jesse Sung <jesse.sung@canonical.com> Acked-by:
Brad Figg <brad.figg@canonical.com> Acked-by:
-
Iyappan Subramanian authored
BugLink: http://bugs.launchpad.net/bugs/1613157Signed-off-by:
Iyappan Subramanian <isubramanian@apm.com> Signed-off-by:
Khuong Dinh <kdinh@apm.com> Signed-off-by:
Tanmay Inamdar <tinamdar@apm.com> Tested-by:
Toan Le <toanle@apm.com> Signed-off-by:
Craig Magina <craig.magina@canonical.com> Acked-by:
-
Iyappan Subramanian authored
BugLink: http://bugs.launchpad.net/bugs/1613157Signed-off-by:
-
Iyappan Subramanian authored
BugLink: http://bugs.launchpad.net/bugs/1613157Signed-off-by:
-
- 15 Aug, 2016 2 commits
-
-
Iyappan Subramanian authored
BugLink: http://bugs.launchpad.net/bugs/1611399 For interrupt controller that doesn't support irq_disable and hardware with level interrupt, an extra interrupt may be pending. This patch fixes the issue by setting IRQ_DISABLE_UNLAZY flag for the interrupt line, as suggested by, 'commit e9849777 ("genirq: Add flag to force mask in disable_irq[_nosync]()")' Signed-off-by:
-
AceLan Kao authored
BugLink: http://bugs.launchpad.net/bugs/1609606 Add MIC mute key which is found on HP Business Slim Keyboard T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 23 Spd=1.5 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=03f0 ProdID=2f4a Rev=00.10 S: Manufacturer=Chicony S: Product=HP Business Slim Keyboard C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid Signed-off-by:
AceLan Kao <acelan.kao@canonical.com> (cherry picked from commit 70e215824134543b75e33236a1988542e9202a07) Signed-off-by:
-
- 12 Aug, 2016 22 commits
-
-
Greg Kroah-Hartman authored
BugLink: http://bugs.launchpad.net/bugs/1611833Signed-off-by:
-
Miklos Szeredi authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit c1892c37 upstream. file_remove_privs() is called with inode lock on file_inode(), which proceeds to calling notify_change() on file->f_path.dentry. Which triggers the WARN_ON_ONCE(!inode_is_locked(inode)) in addition to deadlocking later when ovl_setattr tries to lock the underlying inode again. Fix this mess by not mixing the layers, but doing everything on underlying dentry/inode. Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Fixes: 07a2daab ("ovl: Copy up underlying inode's ->i_mode to overlay inode") Signed-off-by:
-
Alexander Shishkin authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit a36aa80f upstream. Driver initialization tries to request a hub (GTH) driver module from its probe callback, resulting in a deadlock. This patch solves the problem by adding a deferred work for requesting the hub module. Signed-off-by:
Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by:
-
Alexander Shishkin authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 7a1a47ce upstream. This adds Intel(R) Trace Hub PCI ID for Kaby Lake PCH-H. Signed-off-by:
-
Dmitri Epshtein authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 06708f81 upstream. Commit aebea2ba ("net: mvneta: fix Tx interrupt delay") intended to set coalescing threshold to a value guaranteeing interrupt generation per each sent packet, so that buffers can be released with no delay. In fact setting threshold to '1' was wrong, because it causes interrupt every two packets. According to the documentation a reason behind it is following - interrupt occurs once sent buffers counter reaches a value, which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This behavior was confirmed during tests. Also when testing the SoC working as a NAS device, better performance was observed with int-per-packet, as it strongly depends on the fact that all transmitted packets are released immediately. This commit enables NETA controller work in interrupt per sent packet mode by setting coalescing threshold to 0. Signed-off-by:
Dmitri Epshtein <dima@marvell.com> Signed-off-by:
Marcin Wojtas <mw@semihalf.com> Fixes aebea2ba ("net: mvneta: fix Tx interrupt delay") Acked-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Ilya Dryomov authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 930c5328 upstream. Currently, osd_weight and osd_state fields are updated in the encoding order. This is wrong, because an incremental map may look like e.g. new_up_client: { osd=6, addr=... } # set osd_state and addr new_state: { osd=6, xorstate=EXISTS } # clear osd_state Suppose osd6's current osd_state is EXISTS (i.e. osd6 is down). After applying new_up_client, osd_state is changed to EXISTS | UP. Carrying on with the new_state update, we flip EXISTS and leave osd6 in a weird "!EXISTS but UP" state. A non-existent OSD is considered down by the mapping code 2087 for (i = 0; i < pg->pg_temp.len; i++) { 2088 if (ceph_osd_is_down(osdmap, pg->pg_temp.osds[i])) { 2089 if (ceph_can_shift_osds(pi)) 2090 continue; 2091 2092 temp->osds[temp->size++] = CRUSH_ITEM_NONE; and so requests get directed to the second OSD in the set instead of the first, resulting in OSD-side errors like: [WRN] : client.4239 192.168.122.21:0/2444980242 misdirected client.4239.1:2827 pg 2.5df899f2 to osd.4 not [1,4,6] in e680/680 and hung rbds on the client: [ 493.566367] rbd: rbd0: write 400000 at 11cc00000 (0) [ 493.566805] rbd: rbd0: result -6 xferred 400000 [ 493.567011] blk_update_request: I/O error, dev rbd0, sector 9330688 The fix is to decouple application from the decoding and: - apply new_weight first - apply new_state before new_up_client - twiddle osd_state flags if marking in - clear out some of the state if osd is destroyed Fixes: http://tracker.ceph.com/issues/14901Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Josh Durgin <jdurgin@redhat.com> Signed-off-by:
-
Tejun Heo authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 1488a1e3 upstream. Since 34b48db6 ("block: remove artifical max_hw_sectors cap"), max_sectors is no longer limited to BLK_DEF_MAX_SECTORS and LITE-ON CX1-JB256-HP keeps timing out with higher max_sectors. Revert it to the previous value. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by: dgerasimov@gmail.com Link: https://bugzilla.kernel.org/show_bug.cgi?id=121671 Fixes: 34b48db6 ("block: remove artifical max_hw_sectors cap") Signed-off-by:
-
Lukasz Gemborowski authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 22ebf00e upstream. of_address_to_resource return 0 on successful call but devm_ioremap_resource is called only if it returns non-zero value Signed-off-by:
Lukasz Gemborowski <lukasz.gemborowski@nokia.com> Reviewed-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by:
-
Alexey Dobriyan authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 2c13ce8f upstream. Variable "now" seems to be genuinely used unintialized if branch if (CPUCLOCK_PERTHREAD(timer->it_clock)) { is not taken and branch if (unlikely(sighand == NULL)) { is taken. In this case the process has been reaped and the timer is marked as disarmed anyway. So none of the postprocessing of the sample is required. Return right away. Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Link: http://lkml.kernel.org/r/20160707223911.GA26483@p183.telecom.bySigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Brian King authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 54e430bb upstream. If we fall back to using LSI on the Croc or Crocodile chip we need to clear the interrupt so we don't hang the system. Tested-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Alan Stern authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 5e7ff2ca upstream. Commit b704f70c ("SCSI: fix bug in scsi_dev_info_list matching") changed the way vendor- and model-string matching was carried out in the routine that looks up entries in a SCSI devinfo list. The new matching code failed to take into account the case of a maximum-length string; in such cases it could end up testing for a terminating '\0' byte beyond the end of the memory allocated to the string. This out-of-bounds bug was detected by UBSAN. I don't know if anybody has actually encountered this bug. The symptom would be that a device entry in the blacklist might not be matched properly if it contained an 8-character vendor name or a 16-character model name. Such entries certainly exist in scsi_static_device_list. This patch fixes the problem by adding a check for a maximum-length string before the '\0' test. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Fixes: b704f70c ("SCSI: fix bug in scsi_dev_info_list matching") Tested-by:
Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de> Signed-off-by:
-
Vegard Nossum authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 3dad5424 upstream. If register_pernet_subsys() fails, we shouldn't try to call unregister_pernet_subsys(). Fixes: 467fa153 ("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.") Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
Oliver Hartkopp authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 25e1ed6e upstream. For 'real' hardware CAN devices the netlink interface is used to set CAN specific communication parameters. Real CAN hardware can not be created nor removed with the ip tool ... This patch adds a private dellink function for the CAN device driver interface that does just nothing. It's a follow up to commit 993e6f2f ("can: fix oops caused by wrong rtnl newlink usage") but for dellink. Reported-by:
ajneu <ajneu1@gmail.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Oliver Hartkopp authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit bce271f2 upstream. With upstream commit bb208f14 (can: fix handling of unmodifiable configuration options) a new can_validate() function was introduced. When invoking 'ip link set can0 type can' without any configuration data can_validate() tries to validate the content without taking into account that there's totally no content. This patch adds a check for missing content. Reported-by:
-
Thor Thayer authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 427460c8 upstream. When testing CAN write floods on Altera's CycloneV, the first 2 bytes are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also observed bytes 4 & 5 were corrupted in some cases. The D_CAN Data registers are 32 bits and changing from 16 bit writes to 32 bit writes fixes the problem. Testing performed on Altera CycloneV (D_CAN). Requesting tests on other C_CAN & D_CAN platforms. Reported-by:
Richard Andrysek <richard.andrysek@gomtec.de> Signed-off-by:
Thor Thayer <tthayer@opensource.altera.com> Signed-off-by:
-
Wolfgang Grandegger authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 43200a44 upstream. At high bus load it could happen that "at91_poll()" enters with all RX message boxes filled up. If then at the end the "quota" is exceeded as well, "rx_next" will not be reset to the first RX mailbox and hence the interrupts remain disabled. Signed-off-by:
Wolfgang Grandegger <wg@grandegger.com> Tested-by:
Amr Bekhit <amrbekhit@gmail.com> Signed-off-by:
-
Stephane Eranian authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 1424a09a upstream. This patch fixes broken PEBS support on Intel Atom and Core2 due to wrong pointer arithmetic in intel_pmu_drain_pebs_core(). The get_next_pebs_record_by_bit() was called on PEBS format fmt0 which does not use the pebs_record_nhm layout. Signed-off-by:
Stephane Eranian <eranian@google.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: kan.liang@intel.com Fixes: 21509084 ("perf/x86/intel: Handle multiple records in the PEBS buffer") Link: http://lkml.kernel.org/r/1449182000-31524-3-git-send-email-eranian@google.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Miklos Szeredi authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit b99c2d91 upstream. Before 4bacc9c9 ("overlayfs: Make f_path...") file->f_path pointed to the underlying file, hence suid/sgid removal on write worked fine. After that patch file->f_path pointed to the overlay file, and the file mode bits weren't copied to overlay_inode->i_mode. So the suid/sgid removal simply stopped working. The fix is to copy the mode bits, but then ovl_setattr() needs to clear ATTR_MODE to avoid the BUG() in notify_change(). So do this first, then in the next patch copy the mode. Reported-by:
Eryu Guan <eguan@redhat.com> Signed-off-by:
-
Peter Zijlstra authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 7dd49125 upstream. Starting with the following commit: fde7d22e ("sched/fair: Fix overly small weight for interactive group entities") calc_tg_weight() doesn't compute the right value as expected by effective_load(). The difference is in the 'correction' term. In order to ensure \Sum rw_j >= rw_i we cannot use tg->load_avg directly, since that might be lagging a correction on the current cfs_rq->avg.load_avg value. Therefore we use tg->load_avg - cfs_rq->tg_load_avg_contrib + cfs_rq->avg.load_avg. Now, per the referenced commit, calc_tg_weight() doesn't use cfs_rq->avg.load_avg, as is later used in @w, but uses cfs_rq->load.weight instead. So stop using calc_tg_weight() and do it explicitly. The effects of this bug are wake_affine() making randomly poor choices in cgroup-intense workloads. Signed-off-by:
-
Taras Kondratiuk authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit f68381a7 upstream. The code that fills packed command header assumes that CPU runs in little-endian mode. Hence the header is malformed in big-endian mode and causes MMC data transfer errors: [ 563.200828] mmcblk0: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc40 [ 563.219647] mmcblk0: packed cmd failed, nr 2, sectors 16, failure index: -1 Convert header data to LE. Signed-off-by:
Taras Kondratiuk <takondra@cisco.com> Fixes: ce39f9d1 ("mmc: support packed write command for eMMC4.5 devices") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Omar Sandoval authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 8ba86821 upstream. get_task_ioprio() accesses the task->io_context without holding the task lock and thus can race with exit_io_context(), leading to a use-after-free. The reproducer below hits this within a few seconds on my 4-core QEMU VM: #define _GNU_SOURCE #include <assert.h> #include <unistd.h> #include <sys/syscall.h> #include <sys/wait.h> int main(int argc, char **argv) { pid_t pid, child; long nproc, i; /* ioprio_set(IOPRIO_WHO_PROCESS, 0, IOPRIO_PRIO_VALUE(IOPRIO_CLASS_IDLE, 0)); */ syscall(SYS_ioprio_set, 1, 0, 0x6000); nproc = sysconf(_SC_NPROCESSORS_ONLN); for (i = 0; i < nproc; i++) { pid = fork(); assert(pid != -1); if (pid == 0) { for (;;) { pid = fork(); assert(pid != -1); if (pid == 0) { _exit(0); } else { child = wait(NULL); assert(child == pid); } } } pid = fork(); assert(pid != -1); if (pid == 0) { for (;;) { /* ioprio_get(IOPRIO_WHO_PGRP, 0); */ syscall(SYS_ioprio_get, 2, 0); } } } for (;;) { /* ioprio_get(IOPRIO_WHO_PGRP, 0); */ syscall(SYS_ioprio_get, 2, 0); } return 0; } This gets us KASAN dumps like this: [ 35.526914] ================================================================== [ 35.530009] BUG: KASAN: out-of-bounds in get_task_ioprio+0x7b/0x90 at addr ffff880066f34e6c [ 35.530009] Read of size 2 by task ioprio-gpf/363 [ 35.530009] ============================================================================= [ 35.530009] BUG blkdev_ioc (Not tainted): kasan: bad access detected [ 35.530009] ----------------------------------------------------------------------------- [ 35.530009] Disabling lock debugging due to kernel taint [ 35.530009] INFO: Allocated in create_task_io_context+0x2b/0x370 age=0 cpu=0 pid=360 [ 35.530009] ___slab_alloc+0x55d/0x5a0 [ 35.530009] __slab_alloc.isra.20+0x2b/0x40 [ 35.530009] kmem_cache_alloc_node+0x84/0x200 [ 35.530009] create_task_io_context+0x2b/0x370 [ 35.530009] get_task_io_context+0x92/0xb0 [ 35.530009] copy_process.part.8+0x5029/0x5660 [ 35.530009] _do_fork+0x155/0x7e0 [ 35.530009] SyS_clone+0x19/0x20 [ 35.530009] do_syscall_64+0x195/0x3a0 [ 35.530009] return_from_SYSCALL_64+0x0/0x6a [ 35.530009] INFO: Freed in put_io_context+0xe7/0x120 age=0 cpu=0 pid=1060 [ 35.530009] __slab_free+0x27b/0x3d0 [ 35.530009] kmem_cache_free+0x1fb/0x220 [ 35.530009] put_io_context+0xe7/0x120 [ 35.530009] put_io_context_active+0x238/0x380 [ 35.530009] exit_io_context+0x66/0x80 [ 35.530009] do_exit+0x158e/0x2b90 [ 35.530009] do_group_exit+0xe5/0x2b0 [ 35.530009] SyS_exit_group+0x1d/0x20 [ 35.530009] entry_SYSCALL_64_fastpath+0x1a/0xa4 [ 35.530009] INFO: Slab 0xffffea00019bcd00 objects=20 used=4 fp=0xffff880066f34ff0 flags=0x1fffe0000004080 [ 35.530009] INFO: Object 0xffff880066f34e58 @offset=3672 fp=0x0000000000000001 [ 35.530009] ================================================================== Fix it by grabbing the task lock while we poke at the io_context. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Omar Sandoval <osandov@fb.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Dan Carpenter authored
BugLink: http://bugs.launchpad.net/bugs/1611833 commit 096cdc6f upstream. We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure that those values have not changed between the two copy_from_user() calls. Otherwise it could lead to a buffer overflow. Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value. We should use the new smaller value so we don't copy too much data to the user. Reported-by:
Pengfei Wang <wpengfeinudt@gmail.com> Fixes: a8411784 ('mfd: cros_ec: Use a zero-length array for command data') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Tested-by:
Gwendal Grignou <gwendal@chromium.org> Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
