Pull module fix from Luis Chamberlain:
 "Fixes module decompression when CONFIG_SYSFS=n

  The only fix trickled down for v5.17-rc cycle so far is the fix for
  module decompression when CONFIG_SYSFS=n. This was reported through
  0-day"

* tag 'modules-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
  module: fix building with sysfs disabled

Oded Gabbay reports that enabling NUMA balancing causes corruption with
his Gaudi accelerator test load:

 "All the details are in the bug, but the bottom line is that somehow,
  this patch causes corruption when the numa balancing feature is
  enabled AND we don't use process affinity AND we use GUP to pin pages
  so our accelerator can DMA to/from system memory.

  Either disabling numa balancing, using process affinity to bind to
  specific numa-node or reverting this patch causes the bug to
  disappear"

and Oded bisected the issue to commit 09854ba9 ("mm: do_wp_page()
simplification").

Now, the NUMA balancing shouldn't actually be changing the writability
of a page, and as such shouldn't matter for COW.  But it appears it
does.  Suspicious.

However, regardless of that, the condition for enabling NUMA faults in
change_pte_range() is nonsensical.  It uses "page_mapcount(page)" to
decide if a COW page should be NUMA-protected or not, and that makes
absolutely no sense.

The number of mappings a page has is irrelevant: not only does GUP get a
reference to a page as in Oded's case, but the other mappings migth be
paged out and the only reference to them would be in the page count.

Since we should never try to NUMA-balance a page that we can't move
anyway due to other references, just fix the code to use 'page_count()'.
Oded confirms that that fixes his issue.

Now, this does imply that something in NUMA balancing ends up changing
page protections (other than the obvious one of making the page
inaccessible to get the NUMA faulting information).  Otherwise the COW
simplification wouldn't matter - since doing the GUP on the page would
make sure it's writable.

The cause of that permission change would be good to figure out too,
since it clearly results in spurious COW events - but fixing the
nonsensical test that just happened to work before is obviously the
CorrectThing(tm) to do regardless.

Fixes: 09854ba9 ("mm: do_wp_page() simplification")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215616
Link: https://lore.kernel.org/all/CAFCwf10eNmwq2wD71xjUhqkvv5+_pJMR1nPug2RqNDcFT4H86Q@mail.gmail.com/Reported-and-tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Sysfs support might be disabled so we need to guard the code that
instantiates "compression" attribute with an #ifdef.

Fixes: b1ae6dc4 ("module: add in-kernel support for decompressing")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>

Pull MMC fix from Ulf Hansson:
 "Fix recovery logic for multi block I/O reads (MMC_READ_MULTIPLE_BLOCK)"

* tag 'mmc-v5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: block: fix read single on recovery logic

Daniel Gibson reports that the n_tty code gets line termination wrong in
very specific cases:

 "If you feed a line with exactly 64 chars + terminating newline, and
  directly afterwards (without reading) another line into a pseudo
  terminal, the the first read() on the other side will return the 64
  char line *without* terminating newline, and the next read() will
  return the missing terminating newline AND the complete next line (if
  it fits in the buffer)"

and bisected the behavior to commit 3b830a9c ("tty: convert
tty_ldisc_ops 'read()' function to take a kernel pointer").

Now, digging deeper, it turns out that the behavior isn't exactly new:
what changed in commit 3b830a9c was that the tty line discipline
.read() function is now passed an intermediate kernel buffer rather than
the final user space buffer.

And that intermediate kernel buffer is 64 bytes in size - thus that
special case with exactly 64 bytes plus terminating newline.

The same problem did exist before, but historically the boundary was not
the 64-byte chunk, but the user-supplied buffer size, which is obviously
generally bigger (and potentially bigger than N_TTY_BUF_SIZE, which
would hide the issue entirely).

The reason is that the n_tty canon_copy_from_read_buf() code would look
ahead for the EOL character one byte further than it would actually
copy.  It would then decide that it had found the terminator, and unmark
it as an EOL character - which in turn explains why the next read
wouldn't then be terminated by it.

Now, the reason it did all this in the first place is related to some
historical and pretty obscure EOF behavior, see commit ac8f3bf8
("n_tty: Fix poll() after buffer-limited eof push read") and commit
40d5e090 ("n_tty: Fix EOF push handling").

And the reason for the EOL confusion is that we treat EOF as a special
EOL condition, with the EOL character being NUL (aka "__DISABLED_CHAR"
in the kernel sources).

So that EOF look-ahead also affects the normal EOL handling.

This patch just removes the look-ahead that causes problems, because EOL
is much more critical than the historical "EOF in the middle of a line
that coincides with the end of the buffer" handling ever was.

Now, it is possible that we should indeed re-introduce the "look at next
character to see if it's a EOF" behavior, but if so, that should be done
not at the kernel buffer chunk boundary in canon_copy_from_read_buf(),
but at a higher level, when we run out of the user buffer.

In particular, the place to do that would be at the top of
'n_tty_read()', where we check if it's a continuation of a previously
started read, and there is no more buffer space left, we could decide to
just eat the __DISABLED_CHAR at that point.

But that would be a separate patch, because I suspect nobody actually
cares, and I'd like to get a report about it before bothering.

Fixes: 3b830a9c ("tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer")
Fixes: ac8f3bf8 ("n_tty: Fix  poll() after buffer-limited eof push read")
Fixes: 40d5e090 ("n_tty: Fix EOF push handling")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611Reported-and-tested-by: Daniel Gibson <metalcaedes@gmail.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull kvm fixes from Paolo Bonzini:
 "ARM:

   - Read HW interrupt pending state from the HW

  x86:

   - Don't truncate the performance event mask on AMD

   - Fix Xen runstate updates to be atomic when preempting vCPU

   - Fix for AMD AVIC interrupt injection race

   - Several other AMD fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86/pmu: Use AMD64_RAW_EVENT_MASK for PERF_TYPE_RAW
  KVM: x86/pmu: Don't truncate the PerfEvtSeln MSR when creating a perf event
  KVM: SVM: fix race between interrupt delivery and AVIC inhibition
  KVM: SVM: set IRR in svm_deliver_interrupt
  KVM: SVM: extract avic_ring_doorbell
  selftests: kvm: Remove absent target file
  KVM: arm64: vgic: Read HW interrupt pending state from the HW
  KVM: x86/xen: Fix runstate updates to be atomic when preempting vCPU
  KVM: x86: SVM: move avic definitions from AMD's spec to svm.h
  KVM: x86: lapic: don't touch irr_pending in kvm_apic_update_apicv when inhibiting it
  KVM: x86: nSVM: deal with L1 hypervisor that intercepts interrupts but lets L2 control them
  KVM: x86: nSVM: expose clean bit support to the guest
  KVM: x86: nSVM/nVMX: set nested_run_pending on VM entry which is a result of RSM
  KVM: x86: nSVM: mark vmcb01 as dirty when restoring SMM saved state
  KVM: x86: nSVM: fix potential NULL derefernce on nested migration
  KVM: x86: SVM: don't passthrough SMAP/SMEP/PKE bits in !NPT && !gCR0.PG case
  Revert "svm: Add warning message for AVIC IPI invalid target"

Pull HID fixes from Jiri Kosina:

 - memory leak fix for hid-elo driver (Dongliang Mu)

 - fix for hangs on newer AMD platforms with amd_sfh-driven hardware
   (Basavaraj Natikar )

 - locking fix in i2c-hid (Daniel Thompson)

 - a few device-ID specific quirks

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
  HID: amd_sfh: Add interrupt handler to process interrupts
  HID: amd_sfh: Add functionality to clear interrupts
  HID: amd_sfh: Disable the interrupt for all command
  HID: amd_sfh: Correct the structure field name
  HID: amd_sfh: Handle amd_sfh work buffer in PM ops
  HID:Add support for UGTABLET WP5540
  HID: amd_sfh: Add illuminance mask to limit ALS max value
  HID: amd_sfh: Increase sensor command timeout
  HID: i2c-hid: goodix: Fix a lockdep splat
  HID: elo: fix memory leak in elo_probe
  HID: apple: Set the tilde quirk flag on the Wellspring 5 and later

Pull btrfs fixes from David Sterba:

 - yield CPU more often when defragmenting a large file

 - skip defragmenting extents already under writeback

 - improve error message when send fails to write file data

 - get rid of warning when mounted with 'flushoncommit'

* tag 'for-5.17-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: send: in case of IO error log it
  btrfs: get rid of warning on transaction commit when using flushoncommit
  btrfs: defrag: don't try to defrag extents which are under writeback
  btrfs: don't hold CPU for too long when defragging a file

Pull parisc architecture fixes from Helge Deller:

 - Fix miscompilations when function calls are made from inside a
   put_user() call

 - Drop __init from map_pages() declaration to avoid random boot crashes

 - Added #error messages if a 64-bit compiler was used to build a 32-bit
   kernel (and vice versa)

 - Fix out-of-bound data TLB miss faults in sba_iommu and ccio-dma
   drivers

 - Add ioread64_lo_hi() and iowrite64_lo_hi() functions to avoid kernel
   test robot errors

 - Fix link failure when 8250_gsc driver is built without CONFIG_IOSAPIC

* tag 'for-5.17/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  serial: parisc: GSC: fix build when IOSAPIC is not set
  parisc: Fix some apparent put_user() failures
  parisc: Show error if wrong 32/64-bit compiler is being used
  parisc: Add ioread64_lo_hi() and iowrite64_lo_hi()
  parisc: Fix sglist access in ccio-dma.c
  parisc: Fix data TLB miss in sba_unmap_sg
  parisc: Drop __init from map_pages declaration

Merge tag 'hyperv-fixes-signed-20220215' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux

Pull hyperv fixes from Wei Liu:

 - Rework use of DMA_BIT_MASK in vmbus to work around a clang bug
   (Michael Kelley)

 - Fix NUMA topology (Long Li)

 - Fix a memory leak in vmbus (Miaoqian Lin)

 - One minor clean-up patch (Cai Huoqing)

* tag 'hyperv-fixes-signed-20220215' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
  Drivers: hv: utils: Make use of the helper macro LIST_HEAD()
  Drivers: hv: vmbus: Rework use of DMA_BIT_MASK(64)
  Drivers: hv: vmbus: Fix memory leak in vmbus_add_channel_kobj
  PCI: hv: Fix NUMA node assignment when kernel boots with custom NUMA topology

There is a build error when using a kernel .config file from
'kernel test robot' for a different build problem:

hppa64-linux-ld: drivers/tty/serial/8250/8250_gsc.o: in function `.LC3':
(.data.rel.ro+0x18): undefined reference to `iosapic_serial_irq'

when:
  CONFIG_GSC=y
  CONFIG_SERIO_GSCPS2=y
  CONFIG_SERIAL_8250_GSC=y
  CONFIG_PCI is not set
    and hence PCI_LBA is not set.
  IOSAPIC depends on PCI_LBA, so IOSAPIC is not set/enabled.

Make the use of iosapic_serial_irq() conditional to fix the build error.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>

Merge tag 'regulator-fix-v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fix from Mark Brown:
 "One fix here, for initialisation of regulators that don't have an
  in_enabled() operation which would mainly impact cases where they
  aren't otherwise used during early setup for some reason"

* tag 'regulator-fix-v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: core: fix false positive in regulator_late_cleanup()

On newer AMD platforms with SFH, it is observed that random interrupts
get generated on the SFH hardware and until this is cleared the firmware
sensor processing is stalled, resulting in no data been received to
driver side.

Add routines to handle these interrupts, so that firmware operations are
not stalled.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Newer AMD platforms with SFH may generate interrupts on some events
which are unwarranted. Until this is cleared the actual MP2 data
processing maybe stalled in some cases.

Add a mechanism to clear the pending interrupts (if any) during the
driver initialization and sensor command operations.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Sensor data is processed in polling mode. Hence disable the interrupt
for all sensor command.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Misinterpreted intr_enable field name. Hence correct the structure
field name accordingly to reflect the functionality.

Fixes: f264481a ("HID: amd_sfh: Extend driver capabilities for multi-generation support")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Since in the current amd_sfh design the sensor data is periodically
obtained in the form of poll data, during the suspend/resume cycle,
scheduling a delayed work adds no value.

So, cancel the work and restart back during the suspend/resume cycle
respectively.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

AMD's event select is 3 nybbles, with the high nybble in bits 35:32 of
a PerfEvtSeln MSR. Don't mask off the high nybble when configuring a
RAW perf event.

Fixes: ca724305 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220203014813.2130559-2-jmattson@google.com>
Reviewed-by: David Dunn <daviddunn@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

AMD's event select is 3 nybbles, with the high nybble in bits 35:32 of
a PerfEvtSeln MSR. Don't drop the high nybble when setting up the
config field of a perf_event_attr structure for a call to
perf_event_create_kernel_counter().

Fixes: ca724305 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220203014813.2130559-1-jmattson@google.com>
Reviewed-by: David Dunn <daviddunn@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

After commit 4b9d2a73 ("parisc: Switch user access functions
to signal errors in r29 instead of r8") bash suddenly started
to report those warnings after login:

-bash: cannot set terminal process group (-1): Bad file descriptor
-bash: no job control in this shell

It turned out, that a function call inside a put_user(), e.g.:
put_user(vt_do_kdgkbmode(console), (int __user *)arg);
clobbered the error register (r29) and thus the put_user() call itself
seem to have failed.

Rearrange the C-code to pre-calculate the intermediate value
and then do the put_user().
Additionally prefer the "+" constraint on pu_err and gu_err registers
to tell the compiler that those operands are both read and written by
the assembly instruction.
Reported-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: 4b9d2a73 ("parisc: Switch user access functions to signal errors in r29 instead of r8")
Signed-off-by: Helge Deller <deller@gmx.de>

It happens quite often that people use the wrong compiler to build the
kernel:

make ARCH=parisc   -> builds the 32-bit kernel
make ARCH=parisc64 -> builds the 64-bit kernel

This patch adds a sanity check which errors out with an instruction how
use the correct ARCH= option.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.15+

Merge tag 'kbuild-fixes-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix the truncated path issue for HAVE_GCC_PLUGINS test in Kconfig

 - Move -Wunsligned-access to W=1 builds to avoid sprinkling warnings
   for the latest Clang

 - Fix missing fclose() in Kconfig

 - Fix Kconfig to touch dep headers correctly when KCONFIG_AUTOCONFIG is
   overridden.

* tag 'kbuild-fixes-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: fix failing to generate auto.conf
  kconfig: fix missing fclose() on error paths
  Makefile.extrawarn: Move -Wunaligned-access to W=1
  kconfig: let 'shell' return enough output for deep path names

Pull irq fixes from Thomas Gleixner:
 "Interrupt chip driver fixes:

   - Don't install an hotplug notifier for GICV3-ITS on systems which do
     not need it to prevent a warning in the notifier about inconsistent
     state

   - Add the missing device tree matching for the T-HEAD PLIC variant so
     the related SoC is properly supported"

* tag 'irq-urgent-2022-02-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/sifive-plic: Add missing thead,c900-plic match string
  dt-bindings: update riscv plic compatible string
  irqchip/gic-v3-its: Skip HP notifier when no ITS is registered

Pull objtool fix from Borislav Petkov:
 "Fix a case where objtool would mistakenly warn about instructions
  being unreachable"

* tag 'objtool_urgent_for_v5.17_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/bug: Merge annotate_reachable() into _BUG_FLAGS() asm

Pull scheduler fix from Borislav Petkov:
 "Fix a NULL-ptr dereference when recalculating a sched entity's weight"

* tag 'sched_urgent_for_v5.17_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix fault in reweight_entity

Pull perf fix from Borislav Petkov:
 "Prevent cgroup event list corruption when switching events"

* tag 'perf_urgent_for_v5.17_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix list corruption in perf_cgroup_switch()

Pull x86 fix from Borislav Petkov:
 "Prevent softlockups when tearing down large SGX enclaves"

* tag 'x86_urgent_for_v5.17_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/sgx: Silence softlockup detection when releasing large enclaves

Pull cifs fixes from Steve French:
 "Three small smb3 reconnect fixes and an error log clarification"

* tag '5.17-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: mark sessions for reconnection in helper function
  cifs: call helper functions for marking channels for reconnect
  cifs: call cifs_reconnect when a connection is marked
  [smb3] improve error message when mount options conflict with posix

Merge tag 'irqchip-fixes-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent

Pull irqchip fixes from Marc Zyngier:

 - Don't register a hotplug notifier on GICv3 systems that advertise
   LPI support, but have no ITS to make use of it

 - Add missing DT matching for the thead,c900-plic variant of the
   SiFive PLIC

Link: https://lore.kernel.org/r/20220211110038.1179155-1-maz@kernel.org

Pull SCSI fixes from James Bottomley:
 "Two minor fixes in the lpfc driver. One changing the classification of
  trace messages and the other fixing a build issue when NVME_FC is
  disabled"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: lpfc: Reduce log messages seen after firmware download
  scsi: lpfc: Remove NVMe support if kernel has NVME_FC disabled

Pull char/misc driver fixes from Greg KH:
 "Here are a small number of char/misc driver fixes for 5.17-rc4 for
  reported issues. They contain:

   - phy driver fixes

   - iio driver fix

   - eeprom driver fix

   - speakup regression fix

   - fastrpc fix

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  iio: buffer: Fix file related error handling in IIO_BUFFER_GET_FD_IOCTL
  speakup-dectlk: Restore pitch setting
  bus: mhi: pci_generic: Add mru_default for Cinterion MV31-W
  bus: mhi: pci_generic: Add mru_default for Foxconn SDX55
  eeprom: ee1004: limit i2c reads to I2C_SMBUS_BLOCK_MAX
  misc: fastrpc: avoid double fput() on failed usercopy
  phy: dphy: Correct clk_pre parameter
  phy: phy-mtk-tphy: Fix duplicated argument in phy-mtk-tphy
  phy: stm32: fix a refcount leak in stm32_usbphyc_pll_enable()
  phy: xilinx: zynqmp: Fix bus width setting for SGMII
  phy: cadence: Sierra: fix error handling bugs in probe()
  phy: ti: Fix missing sentinel for clk_div_table
  phy: broadcom: Kconfig: Fix PHY_BRCM_USB config option
  phy: usb: Leave some clocks running during suspend

Pullstaging driver fixes from Greg KH:
 "Here are two staging driver fixes for 5.17-rc4.  These are:

   - fbtft error path fix

   - vc04_services rcu dereference fix

  Both of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: fbtft: Fix error path in fbtft_driver_module_init()
  staging: vc04_services: Fix RCU dereference check

Pull tty/serial fixes from Greg KH:
 "Here are four small tty/serial fixes for 5.17-rc4.  They are:

   - 8250_pericom change revert to fix a reported regression

   - two speculation fixes for vt_ioctl

   - n_tty regression fix for polling

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  vt_ioctl: add array_index_nospec to VT_ACTIVATE
  vt_ioctl: fix array_index_nospec in vt_setactivate
  serial: 8250_pericom: Revert "Re-enable higher baud rates"
  n_tty: wake up poll(POLLRDNORM) on receiving data

Pull USB fixes from Greg KH:
 "Here are some small USB driver fixes for 5.17-rc4 that resolve some
  reported issues and add new device ids:

   - usb-serial new device ids

   - ulpi cleanup fixes

   - f_fs use-after-free fix

   - dwc3 driver fixes

   - ax88179_178a usb network driver fix

   - usb gadget fixes

  There is a revert at the end of this series to resolve a build problem
  that 0-day found yesterday. Most of these have been in linux-next,
  except for the last few, and all have now passed 0-day tests"

* tag 'usb-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  Revert "usb: dwc2: drd: fix soft connect when gadget is unconfigured"
  usb: dwc2: drd: fix soft connect when gadget is unconfigured
  usb: gadget: rndis: check size of RNDIS_MSG_SET command
  USB: gadget: validate interface OS descriptor requests
  usb: core: Unregister device on component_add() failure
  net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup
  usb: dwc3: gadget: Prevent core from processing stale TRBs
  USB: serial: cp210x: add CPI Bulk Coin Recycler id
  USB: serial: cp210x: add NCR Retail IO box id
  USB: serial: ftdi_sio: add support for Brainboxes US-159/235/320
  usb: gadget: f_uac2: Define specific wTerminalType
  usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
  usb: raw-gadget: fix handling of dual-direction-capable endpoints
  usb: usb251xb: add boost-up property support
  usb: ulpi: Call of_node_put correctly
  usb: ulpi: Move of_node_put to ulpi_dev_release
  USB: serial: option: add ZTE MF286D modem
  USB: serial: ch341: add support for GW Instek USB2.0-Serial devices
  usb: f_fs: Fix use-after-free for epfile
  usb: dwc3: xilinx: fix uninitialized return value

Pull s390 updates from Vasily Gorbik:
 "Maintainers and reviewers changes:

    - Add Alexander Gordeev as maintainer for s390.

    - Christian Borntraeger will focus on s390 KVM maintainership and
      stays as s390 reviewer.

  Fixes:

   - Fix clang build of modules loader KUnit test.

   - Fix kernel panic in CIO code on FCES path-event when no driver is
     attached to a device or the driver does not provide the path_event
     function"

* tag 's390-5.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/cio: verify the driver availability for path_event call
  s390/module: fix building test_modules_helpers.o with clang
  MAINTAINERS: downgrade myself to Reviewer for s390
  MAINTAINERS: add Alexander Gordeev as maintainer for s390

Pull xen fixes from Juergen Gross:

 - Two small cleanups

 - Another fix for addressing the EFI framebuffer above 4GB when running
   as Xen dom0

 - A patch to let Xen guests use reserved bits in MSI- and IO-APIC-
   registers for extended APIC-IDs the same way KVM guests are doing it
   already

* tag 'for-linus-5.17a-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/pci: Make use of the helper macro LIST_HEAD()
  xen/x2apic: Fix inconsistent indenting
  xen/x86: detect support for extended destination ID
  xen/x86: obtain full video frame buffer address for Dom0 also under EFI

Pull seccomp fixes from Kees Cook:
 "This fixes a corner case of fatal SIGSYS being ignored since v5.15.
  Along with the signal fix is a change to seccomp so that seeing
  another syscall after a fatal filter result will cause seccomp to kill
  the process harder.

  Summary:

   - Force HANDLER_EXIT even for SIGNAL_UNKILLABLE

   - Make seccomp self-destruct after fatal filter results

   - Update seccomp samples for easier behavioral demonstration"

* tag 'seccomp-v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  samples/seccomp: Adjust sample to also provide kill option
  seccomp: Invalidate seccomp mode to catch death failures
  signal: HANDLER_EXIT should clear SIGNAL_UNKILLABLE

Merge misc fixes from Andrew Morton:
 "5 patches.

  Subsystems affected by this patch series: binfmt, procfs, and mm
  (vmscan, memcg, and kfence)"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  kfence: make test case compatible with run time set sample interval
  mm: memcg: synchronize objcg lists with a dedicated spinlock
  mm: vmscan: remove deadlock due to throttling failing to make progress
  fs/proc: task_mmu.c: don't read mapcount for migration entry
  fs/binfmt_elf: fix PT_LOAD p_align values for loaders

When the KCONFIG_AUTOCONFIG is specified (e.g. export \
KCONFIG_AUTOCONFIG=output/config/auto.conf), the directory of
include/config/ will not be created, so kconfig can't create deps
files in it and auto.conf can't be generated.
Signed-off-by: Jing Leng <jleng@ambarella.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>