- 21 Oct, 2013 10 commits
-
-
Merav Sicron authored
Current driver implementation incorrectly sets the flag only if 64-bit DMA mask succeeded. Signed-off-by:
Merav Sicron <meravs@broadcom.com> Signed-off-by:
Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by:
Ariel Elior <ariele@broadcom.com> Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dmitry Kravkov authored
As part of a register dump, the interface pretends to have the identity of other interfaces of the same physical device in order to perform HW configuration for them - specifically, it needs to prevent attentions from generating on those functions as the register dump accesses registers in common blocks which whose reading might generate an attention. However, such pretension is unsafe - unlike other flows in which the driver uses pretend, during register dump there is no guarantee no other HW access will take place (by other flows). If such access will take place, the HW will be accessed by the wrong interface, and leave both functions in an incorrect state. This patch removes all pretensions from the register dump flow. Instead, it changes initial configuration of attentions such that no fatal attention will be generated for other functions as a result of the register dump (notice however, a debug print claiming an attention from other functions IS possible during the register dump) Signed-off-by:
Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
-
Ariel Elior authored
bnx2x has several clients to its DMAE machines - all of them with the exception of the statistics flow used the same locking mechanisms to synchronize the DMAE machines' usage. Since statistics (which are periodically entered) use DMAE without taking the locks, they may erase the commands which were previously set - e.g., it may cause a VF to timeout while waiting for a PF answer on the VF-PF channel as that command header would have been overwritten by the statistics' header. This patch makes certain that all flows utilizing DMAE will use the same API, assuring that the locking scheme will be kept by all said flows. Signed-off-by:
-
Yuval Mintz authored
If debug message is open and bnx2x_vfop_qdtor_cmd() were to fail, the resulting print would have caused a null pointer dereference. Signed-off-by:
-
Ariel Elior authored
Starting with commit b9871bcf "bnx2x: VF RSS support - PF side", if a PF will have SR-IOV supported in its PCI configuration space, storage drivers will not work for that interface. This patch fixes the resource calculation to allow such a configuration to properly work. Signed-off-by:
-
Dmitry Kravkov authored
bnx2x drivers configure coalescing incorrectly (e.g., as a result of a call to 'ethtool -c'). Although this is almost invisible to the user (due to NAPI) designated tests will show the configuration is incorrect. Signed-off-by:
-
Ariel Elior authored
Current code returns upon failure, leaving the VF-PF in an unusable state; This patch adds the missing release so further commands could pass between PF and VF. Signed-off-by:
-
Yuval Mintz authored
During a panic, the driver tries to print the Management FW buffer of recent commands. To do so, the driver reads the address of that buffer from a known address. If the buffer is unavailable (e.g., PCI reads don't work, MCP is failing, etc.), the driver will try to access the address it has read, possibly causing a kernel panic. This check 'sanitizes' the access, validating the read value is indeed a valid address inside the management FW's buffers. The patch also removes a read outside the scope of the buffer, which resulted in some unrelated chraracters appearing in the log. Signed-off-by:
-
Yuval Mintz authored
bnx2x VFs do not support Multi-CoS; Current implementation erroneously sets the VFs maximal number of CoS to be > 1. This will cause the driver to call alloc_etherdev_mqs() with a number of queues it cannot possibly support and reflects in 'odd' driver prints. Signed-off-by:
-
Mugunthan V N authored
When interrupt pacing is enabled, receive/transmit statistics are not updated properly by hardware which leads to ISR return with IRQ_NONE and inturn kernel disables the interrupt. This patch removed the checking of receive/transmit statistics from ISR. This patch is verified with AM335x Beagle Bone Black and below is the kernel warn when interrupt pacing is enabled. [ 104.298254] irq 58: nobody cared (try booting with the "irqpoll" option) [ 104.305356] CPU: 0 PID: 1073 Comm: iperf Not tainted 3.12.0-rc3-00342-g77d4015b #3 [ 104.313284] [<c001bb84>] (unwind_backtrace+0x0/0xf0) from [<c0017db0>] (show_stack+0x10/0x14) [ 104.322282] [<c0017db0>] (show_stack+0x10/0x14) from [<c0507920>] (dump_stack+0x78/0x94) [ 104.330816] [<c0507920>] (dump_stack+0x78/0x94) from [<c0088c1c>] (__report_bad_irq+0x20/0xc0) [ 104.339889] [<c0088c1c>] (__report_bad_irq+0x20/0xc0) from [<c008912c>] (note_interrupt+0x1dc/0x23c) [ 104.349505] [<c008912c>] (note_interrupt+0x1dc/0x23c) from [<c0086d74>] (handle_irq_event_percpu+0xc4/0x238) [ 104.359851] [<c0086d74>] (handle_irq_event_percpu+0xc4/0x238) from [<c0086f24>] (handle_irq_event+0x3c/0x5c) [ 104.370198] [<c0086f24>] (handle_irq_event+0x3c/0x5c) from [<c008991c>] (handle_level_irq+0xac/0x10c) [ 104.379907] [<c008991c>] (handle_level_irq+0xac/0x10c) from [<c00866d8>] (generic_handle_irq+0x20/0x30) [ 104.389812] [<c00866d8>] (generic_handle_irq+0x20/0x30) from [<c0014ce8>] (handle_IRQ+0x4c/0xb0) [ 104.399066] [<c0014ce8>] (handle_IRQ+0x4c/0xb0) from [<c000856c>] (omap3_intc_handle_irq+0x60/0x74) [ 104.408598] [<c000856c>] (omap3_intc_handle_irq+0x60/0x74) from [<c050d8e4>] (__irq_svc+0x44/0x5c) [ 104.418021] Exception stack(0xde4f7c00 to 0xde4f7c48) [ 104.423345] 7c00: 00000001 00000000 00000000 dd002140 60000013 de006e54 00000002 00000000 [ 104.431952] 7c20: de345748 00000040 c11c8588 00018ee0 00000000 de4f7c48 c009dfc8 c050d300 [ 104.440553] 7c40: 60000013 ffffffff [ 104.444237] [<c050d8e4>] (__irq_svc+0x44/0x5c) from [<c050d300>] (_raw_spin_unlock_irqrestore+0x34/0x44) [ 104.454220] [<c050d300>] (_raw_spin_unlock_irqrestore+0x34/0x44) from [<c00868c0>] (__irq_put_desc_unlock+0x14/0x38) [ 104.465295] [<c00868c0>] (__irq_put_desc_unlock+0x14/0x38) from [<c0088068>] (enable_irq+0x4c/0x74) [ 104.474829] [<c0088068>] (enable_irq+0x4c/0x74) from [<c03abd24>] (cpsw_poll+0xb8/0xdc) [ 104.483276] [<c03abd24>] (cpsw_poll+0xb8/0xdc) from [<c044ef68>] (net_rx_action+0xc0/0x1e8) [ 104.492085] [<c044ef68>] (net_rx_action+0xc0/0x1e8) from [<c0048a90>] (__do_softirq+0x100/0x27c) [ 104.501338] [<c0048a90>] (__do_softirq+0x100/0x27c) from [<c0048cd0>] (do_softirq+0x68/0x70) [ 104.510224] [<c0048cd0>] (do_softirq+0x68/0x70) from [<c0048e8c>] (local_bh_enable+0xd0/0xe4) [ 104.519211] [<c0048e8c>] (local_bh_enable+0xd0/0xe4) from [<c048c774>] (tcp_rcv_established+0x450/0x648) [ 104.529201] [<c048c774>] (tcp_rcv_established+0x450/0x648) from [<c0494904>] (tcp_v4_do_rcv+0x154/0x474) [ 104.539195] [<c0494904>] (tcp_v4_do_rcv+0x154/0x474) from [<c043d750>] (release_sock+0xac/0x1ac) [ 104.548448] [<c043d750>] (release_sock+0xac/0x1ac) from [<c04844e8>] (tcp_recvmsg+0x4d0/0xa8c) [ 104.557528] [<c04844e8>] (tcp_recvmsg+0x4d0/0xa8c) from [<c04a8720>] (inet_recvmsg+0xcc/0xf0) [ 104.566507] [<c04a8720>] (inet_recvmsg+0xcc/0xf0) from [<c0439744>] (sock_recvmsg+0x90/0xb0) [ 104.575394] [<c0439744>] (sock_recvmsg+0x90/0xb0) from [<c043b778>] (SyS_recvfrom+0x88/0xd8) [ 104.584280] [<c043b778>] (SyS_recvfrom+0x88/0xd8) from [<c043b7e0>] (sys_recv+0x18/0x20) [ 104.592805] [<c043b7e0>] (sys_recv+0x18/0x20) from [<c0013da0>] (ret_fast_syscall+0x0/0x48) [ 104.601587] handlers: [ 104.603992] [<c03acd94>] cpsw_interrupt [ 104.608040] Disabling IRQ #58 Cc: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by:
Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by:
-
- 19 Oct, 2013 6 commits
-
-
David S. Miller authored
Jiri Pirko says: ==================== UFO fixes Couple of patches fixing UFO functionality in different situations. v1->v2: - minor if{}else{} coding style adjustment suggested by Sergei Shtylyov ==================== Signed-off-by: -
Jiri Pirko authored
Now, if user application does: sendto len<mtu flag MSG_MORE sendto len>mtu flag 0 The skb is not treated as fragmented one because it is not initialized that way. So move the initialization to fix this. introduced by: commit e89e9cf5 "[IPv4/IPv6]: UFO Scatter-gather approach" Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Jiri Pirko authored
Now, if user application does: sendto len<mtu flag MSG_MORE sendto len>mtu flag 0 The skb is not treated as fragmented one because it is not initialized that way. So move the initialization to fix this. introduced by: commit e89e9cf5 "[IPv4/IPv6]: UFO Scatter-gather approach" Signed-off-by:
-
Jiri Pirko authored
if up->pending != 0 dontfrag is left with default value -1. That causes that application that do: sendto len>mtu flag MSG_MORE sendto len>mtu flag 0 will receive EMSGSIZE errno as the result of the second sendto. This patch fixes it by respecting IPV6_DONTFRAG socket option. introduced by: commit 4b340ae2 "IPv6: Complete IPV6_DONTFRAG support" Signed-off-by:
-
Seif Mazareeb authored
When CONFIG_NETLABEL is disabled, the cipso_v4_validate() function could loop forever in the main loop if opt[opt_iter +1] == 0, this will causing a kernel crash in an SMP system, since the CPU executing this function will stall /not respond to IPIs. This problem can be reproduced by running the IP Stack Integrity Checker (http://isic.sourceforge.net) using the following command on a Linux machine connected to DUT: "icmpsic -s rand -d <DUT IP address> -r 123456" wait (1-2 min) Signed-off-by:
Seif Mazareeb <seif@marvell.com> Acked-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Daniel Borkmann authored
In the case of credentials passing in unix stream sockets (dgram sockets seem not affected), we get a rather sparse race after commit 16e57262 ("af_unix: dont send SCM_CREDENTIALS by default"). We have a stream server on receiver side that requests credential passing from senders (e.g. nc -U). Since we need to set SO_PASSCRED on each spawned/accepted socket on server side to 1 first (as it's not inherited), it can happen that in the time between accept() and setsockopt() we get interrupted, the sender is being scheduled and continues with passing data to our receiver. At that time SO_PASSCRED is neither set on sender nor receiver side, hence in cmsg's SCM_CREDENTIALS we get eventually pid:0, uid:65534, gid:65534 (== overflow{u,g}id) instead of what we actually would like to see. On the sender side, here nc -U, the tests in maybe_add_creds() invoked through unix_stream_sendmsg() would fail, as at that exact time, as mentioned, the sender has neither SO_PASSCRED on his side nor sees it on the server side, and we have a valid 'other' socket in place. Thus, sender believes it would just look like a normal connection, not needing/requesting SO_PASSCRED at that time. As reverting 16e57262 would not be an option due to the significant performance regression reported when having creds always passed, one way/trade-off to prevent that would be to set SO_PASSCRED on the listener socket and allow inheriting these flags to the spawned socket on server side in accept(). It seems also logical to do so if we'd tell the listener socket to pass those flags onwards, and would fix the race. Before, strace: recvmsg(4, {msg_name(0)=NULL, msg_iov(1)=[{"blub\n", 4096}], msg_controllen=32, {cmsg_len=28, cmsg_level=SOL_SOCKET, cmsg_type=SCM_CREDENTIALS{pid=0, uid=65534, gid=65534}}, msg_flags=0}, 0) = 5 After, strace: recvmsg(4, {msg_name(0)=NULL, msg_iov(1)=[{"blub\n", 4096}], msg_controllen=32, {cmsg_len=28, cmsg_level=SOL_SOCKET, cmsg_type=SCM_CREDENTIALS{pid=11580, uid=1000, gid=1000}}, msg_flags=0}, 0) = 5 Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by:
-
- 18 Oct, 2013 8 commits
-
-
Himanshu Madhani authored
o validate Tx queue only in case of adapters which supports multi Tx queue. This patch is to fix regression introduced in commit aa4a1f7d "qlcnic: Enable Tx queue changes using ethtool for 82xx Series adapter" Signed-off-by:
Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by:
-
Vasundhara Volam authored
It is a required field for all TX_CREATE cmd versions > 0. This fixes a driver initialization failure, caused by recent SH-R Firmwares (versions > 10.0.639.0) failing the TX_CREATE cmd when if_id field is not passed. Signed-off-by:
Sathya Perla <sathya.perla@emulex.com> Signed-off-by:
-
Salva Peiró authored
The wanxl_ioctl() code fails to initialize the two padding bytes of struct sync_serial_settings after the ->loopback member. Add an explicit memset(0) before filling the structure to avoid the info leak. Signed-off-by:
Salva Peiró <speiro@ai2.upv.es> Signed-off-by:
-
David S. Miller authored
Toshiaki Makita says: ==================== bridge: Fix problems around the PVID There seem to be some undesirable behaviors related with PVID. 1. It has no effect assigning PVID to a port. PVID cannot be applied to any frame regardless of whether we set it or not. 2. FDB entries learned via frames applied PVID are registered with VID 0 rather than VID value of PVID. 3. We can set 0 or 4095 as a PVID that are not allowed in IEEE 802.1Q. This leads interoperational problems such as sending frames with VID 4095, which is not allowed in IEEE 802.1Q, and treating frames with VID 0 as they belong to VLAN 0, which is expected to be handled as they have no VID according to IEEE 802.1Q. Note: 2nd and 3rd problems are potential and not exposed unless 1st problem is fixed, because we cannot activate PVID due to it. This is my analysis for each behavior. 1. We are using VLAN_TAG_PRESENT bit when getting PVID, and not when adding/deleting PVID. It can be fixed in either way using or not using VLAN_TAG_PRESENT, but I think the latter is slightly more efficient. 2. We are setting skb->vlan_tci with the value of PVID but the variable vid, which is used in FDB later, is set to 0 at br_allowed_ingress() when untagged frames arrive at a port with PVID valid. I'm afraid that vid should be updated to the value of PVID if PVID is valid. 3. According to IEEE 802.1Q-2011 (6.9.1 and Table 9-2), we cannot use VID 0 or 4095 as a PVID. It looks like that there are more stuff to consider. - VID 0: VID 0 shall not be configured in any FDB entry and used in a tag header to indicate it is a 802.1p priority-tagged frame. Priority-tagged frames should be applied PVID (from IEEE 802.1Q 6.9.1). In my opinion, since we can filter incomming priority-tagged frames by deleting PVID, we don't need to filter them by vlan_bitmap. In other words, priority-tagged frames don't have VID 0 but have no VID, which is the same as untagged frames, and should be filtered by unsetting PVID. So, not only we cannot set PVID as 0, but also we don't need to add 0 to vlan_bitmap, which enables us to simply forbid to add vlan 0. - VID 4095: VID 4095 shall not be transmitted in a tag header. This VID value may be used to indicate a wildcard match for the VID in management operations or FDB entries (from IEEE 802.1Q Table 9-2). In current implementation, we can create a static FDB entry with all existing VIDs by not specifying any VID when creating it. I don't think this way to add wildcard-like entries needs to change, and VID 4095 looks no use and can be unacceptable to add. Consequently, I believe what we should do for 3rd problem is below: - Not allowing VID 0 and 4095 to be added. - Applying PVID to priority-tagged (VID 0) frames. Note: It has been descovered that another problem related to priority-tags remains. If we use vlan 0 interface such as eth0.0, we cannot communicate with another end station via a linux bridge. This problem exists regardless of whether this patch set is applied or not because we might receive untagged frames from another end station even if we are sending priority-tagged frames. This issue will be addressed by another patch set introducing an additional egress policy, on which Vlad Yasevich is working. See http://marc.info/?t=137880893800001&r=1&w=2 for detailed discussion. Patch set follows this mail. The order of patches is not the same as described above, because the way to fix 1st problem is based on the assumption that we don't use VID 0 as a PVID, which is realized by fixing 3rd problem. (1/4)(2/4): Fix 3rd problem. (3/4): Fix 1st problem. (4/4): Fix 2nd probelm. v2: - Add descriptions about the problem related to priority-tags in cover letter. - Revise patch comments to reference the newest spec. ==================== Signed-off-by:
-
Toshiaki Makita authored
We currently set the value that variable vid is pointing, which will be used in FDB later, to 0 at br_allowed_ingress() when we receive untagged or priority-tagged frames, even though the PVID is valid. This leads to FDB updates in such a wrong way that they are learned with VID 0. Update the value to that of PVID if the PVID is applied. Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Reviewed-by:
Vlad Yasevich <vyasevic@redhat.com> Signed-off-by:
-
Toshiaki Makita authored
We are using the VLAN_TAG_PRESENT bit to detect whether the PVID is set or not at br_get_pvid(), while we don't care about the bit in adding/deleting the PVID, which makes it impossible to forward any incomming untagged frame with vlan_filtering enabled. Since vid 0 cannot be used for the PVID, we can use vid 0 to indicate that the PVID is not set, which is slightly more efficient than using the VLAN_TAG_PRESENT. Fix the problem by getting rid of using the VLAN_TAG_PRESENT. Signed-off-by:
-
Toshiaki Makita authored
IEEE 802.1Q says that when we receive priority-tagged (VID 0) frames use the PVID for the port as its VID. (See IEEE 802.1Q-2011 6.9.1 and Table 9-2) Apply the PVID to not only untagged frames but also priority-tagged frames. Signed-off-by:
-
Toshiaki Makita authored
IEEE 802.1Q says that: - VID 0 shall not be configured as a PVID, or configured in any Filtering Database entry. - VID 4095 shall not be configured as a PVID, or transmitted in a tag header. This VID value may be used to indicate a wildcard match for the VID in management operations or Filtering Database entries. (See IEEE 802.1Q-2011 6.9.1 and Table 9-2) Don't accept adding these VIDs in the vlan_filtering implementation. Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
- 17 Oct, 2013 16 commits
-
-
Vlad Yasevich authored
Commit be4f154d bridge: Clamp forward_delay when enabling STP had a typo when attempting to clamp maximum forward delay. It is possible to set bridge_forward_delay to be higher then permitted maximum when STP is off. When turning STP on, the higher then allowed delay has to be clamed down to max value. CC: Herbert Xu <herbert@gondor.apana.org.au> CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
Veaceslav Falico <vfalico@redhat.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Eric Dumazet authored
sk_can_gso() should only be used as a hint in tcp_sendmsg() to build GSO packets in the first place. (As a performance hint) Once we have GSO packets in write queue, we can not decide they are no longer GSO only because flow now uses a route which doesn't handle TSO/GSO. Core networking stack handles the case very well for us, all we need is keeping track of packet counts in MSS terms, regardless of segmentation done later (in GSO or hardware) Right now, if tcp_fragment() splits a GSO packet in two parts, @left and @right, and route changed through a non GSO device, both @left and @right have pcount set to 1, which is wrong, and leads to incorrect packet_count tracking. This problem was added in commit d5ac99a6 ("[TCP]: skb pcount with MTU discovery") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Reported-by:
Maciej Żenczykowski <maze@google.com> Signed-off-by:
-
Eric Dumazet authored
TCP stack should make sure it owns skbs before mangling them. We had various crashes using bnx2x, and it turned out gso_size was cleared right before bnx2x driver was populating TC descriptor of the _previous_ packet send. TCP stack can sometime retransmit packets that are still in Qdisc. Of course we could make bnx2x driver more robust (using ACCESS_ONCE(shinfo->gso_size) for example), but the bug is TCP stack. We have identified two points where skb_unclone() was needed. This patch adds a WARN_ON_ONCE() to warn us if we missed another fix of this kind. Kudos to Neal for finding the root cause of this bug. Its visible using small MSS. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirelessDavid S. Miller authored
John W. Linville says: ==================== Please pull this batch of fixes intended for the 3.12 stream! For the mac80211 bits, Johannes says: "Jouni fixes a remain-on-channel vs. scan bug, and Felix fixes client TX probing on VLANs." And also: "This time I have two fixes from Emmanuel for RF-kill issues, and fixed two issues reported by Evan Huus and Thomas Lindroth respectively." On top of those... Avinash Patil adds a couple of mwifiex fixes to properly inform cfg80211 about some different types of disconnects, avoiding WARNINGs. Mark Cave-Ayland corrects a pointer arithmetic problem in rtlwifi, avoiding incorrect automatic gain calculations. Solomon Peachy sends a cw1200 fix for locking around calls to cw1200_irq_handler, addressing "lost interrupt" problems. Please let me know if there are problems! ==================== Signed-off-by: -
Enrico Mioso authored
This is a QMI device, manufactured by TCT Mobile Phones. A companion patch blacklisting this device's QMI interface in the option.c driver has been sent. Signed-off-by:
Enrico Mioso <mrkiko.rs@gmail.com> Signed-off-by:
Antonella Pellizzari <anto.pellizzari83@gmail.com> Tested-by:
Dan Williams <dcbw@redhat.com> Acked-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Jason Wang authored
We used to schedule the refill work unconditionally after changing the number of queues. This may lead an issue if the device is not up. Since we only try to cancel the work in ndo_stop(), this may cause the refill work still work after removing the device. Fix this by only schedule the work when device is up. The bug were introduce by commit 9b9cd802. (virtio-net: fix the race between channels setting and refill) Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Jason Wang authored
We're trying to re-configure the affinity unconditionally in cpu hotplug callback. This may lead the issue during resuming from s3/s4 since - virt queues haven't been allocated at that time. - it's unnecessary since thaw method will re-configure the affinity. Fix this issue by checking the config_enable and do nothing is we're not ready. The bug were introduced by commit 8de4b2f3 (virtio-net: reset virtqueue affinity when doing cpu hotplug). Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Wanlong Gao <gaowanlong@cn.fujitsu.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Reviewed-by:
Wanlong Gao <gaowanlong@cn.fujitsu.com> Signed-off-by:
-
Dan Carpenter authored
We overwrite the ->bitrate with the user supplied information on the next line. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Dan Carpenter authored
We cap bitrate at YAM_MAXBITRATE in yam_ioctl(), but it could also be negative. I don't know the impact of using a negative bitrate but let's prevent it. Signed-off-by:
-
Markus Pargmann authored
If interrupts happen before napi_enable was called, the driver will not work as expected. Network transmissions are impossible in this state. This bug can be reproduced easily by restarting the network interface in a loop. After some time any network transmissions on the network interface will fail. This patch fixes the bug by enabling napi before enabling the network interface interrupts. Signed-off-by:
Markus Pargmann <mpa@pengutronix.de> Acked-by:
Peter Korsgaard <jacmet@sunsite.dk> Acked-by:
-
Eric Dumazet authored
RPS support is kind of broken on bnx2x, because only non LRO packets get proper rx queue information. This triggers reorders, as it seems bnx2x like to generate a non LRO packet for segment including TCP PUSH flag : (this might be pure coincidence, but all the reorders I've seen involve segments with a PUSH) 11:13:34.335847 IP A > B: . 415808:447136(31328) ack 1 win 457 <nop,nop,timestamp 3789336 3985797> 11:13:34.335992 IP A > B: . 447136:448560(1424) ack 1 win 457 <nop,nop,timestamp 3789336 3985797> 11:13:34.336391 IP A > B: . 448560:479888(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985797> 11:13:34.336425 IP A > B: P 511216:512640(1424) ack 1 win 457 <nop,nop,timestamp 3789337 3985798> 11:13:34.336423 IP A > B: . 479888:511216(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798> 11:13:34.336924 IP A > B: . 512640:543968(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798> 11:13:34.336963 IP A > B: . 543968:575296(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798> We must call skb_record_rx_queue() to properly give to RPS (and more generally for TX queue selection on forward path) the receive queue information. Similar fix is needed for skb_mark_napi_id(), but will be handled in a separate patch to ease stable backports. Signed-off-by:
-
Yuchung Cheng authored
On receiving an ACK that covers the loss probe sequence, TLP immediately sets the congestion state to Open, even though some packets are not recovered and retransmisssion are on the way. The later ACks may trigger a WARN_ON check in step D of tcp_fastretrans_alert(), e.g., https://bugzilla.redhat.com/show_bug.cgi?id=989251 The fix is to follow the similar procedure in recovery by calling tcp_try_keep_open(). The sender switches to Open state if no packets are retransmissted. Otherwise it goes to Disorder and let subsequent ACKs move the state to Recovery or Open. Reported-By:
Michael Sterrett <michael@sterretts.net> Tested-By:
Dormando <dormando@rydia.net> Signed-off-by:
-
Wei Yongjun authored
Fix to return -ENOMEM in the padding pkt alloc fail error handling case instead of 0, as done elsewhere in this function. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
David S. Miller authored
Vlad Yasevich says: ==================== sctp: Use software checksum under certain circumstances. There are some cards that support SCTP checksum offloading. When using these cards with IPSec or forcing IP fragmentation of SCTP traffic, the checksum is computed incorrectly due to the fact that xfrm and IP/IPv6 fragmentation code do not know that this is SCTP traffic and do not know that checksum has to be computed differently. To fix this, we let SCTP detect these conditions and perform software checksum calculation. ==================== Signed-off-by: -
Vlad Yasevich authored
IP/IPv6 fragmentation knows how to compute only TCP/UDP checksum. This causes problems if SCTP packets has to be fragmented and ipsummed has been set to PARTIAL due to checksum offload support. This condition can happen when retransmitting after MTU discover, or when INIT or other control chunks are larger then MTU. Check for the rare fragmentation condition in SCTP and use software checksum calculation in this case. CC: Fan Du <fan.du@windriver.com> Signed-off-by:
Vlad Yasevich <vyasevich@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Fan Du authored
igb/ixgbe have hardware sctp checksum support, when this feature is enabled and also IPsec is armed to protect sctp traffic, ugly things happened as xfrm_output checks CHECKSUM_PARTIAL to do checksum operation(sum every thing up and pack the 16bits result in the checksum field). The result is fail establishment of sctp communication. Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
Fan Du <fan.du@windriver.com> Signed-off-by:
-
